Previously not all references mentioned any spec version at all.
Given r3.1 is the current specification available for evaluation at
www.computeexpresslink.org update references to refer to that.
Hopefully this won't become a never ending job.
A few structure definitions have been updated to add new fields.
Defaults of 0 and read only are valid choices for these new DVSEC
registers so go with that for now.
There are additional error codes and some of the 'questions' in
the comments are resolved now.
Update documentation reference to point to the CXL r3.1 specification
with naming closer to what is on the cover.
For cases where there are structure version numbers, add defines
so they can be found next to the register definitions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As a failure of g_malloc() will result in QEMU exiting, it
won't return a NULL to check. As such, drop the incorrect handling
of such NULL returns in the cdat table building code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CONFIG_ALL is tricky to use and was ported over to Meson from the
recursive processing of Makefile variables. Meson sourcesets
however have all_sources() and all_dependencies() methods that
remove the need for it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Without these being set the PCIE Link Capabilities register has
invalid values in these two fields.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-10-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable it for the switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid repetition of switch upstream port specific data in the
CXLDeviceState structure it will be necessary to access the switch USP
specific data from mailbox callbacks. Hence move it to cxl_device.h so it
is no longer an opaque structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023160806.13206-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Done to reduce line lengths where this is used.
Ext seems sufficiently obvious that it need not be spelt out
fully.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Will be needed so there is a defined serial number for
information queries via the Switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913133615.29876-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to ACPI spec 6.5 5.2.28.4 System Locality Latency and Bandwidth
Information Structure, if the "Entry Base Unit" is 1024 for BW and the
matrix entry has the value of 100, the BW is 100 GB/s. So the
entry_base_unit should be changed from 1000 to 1024 given the comment notes
it's 16GB/s for .latency_bandwidth.
Fixes: 882877fc35 ("hw/pci-bridge/cxl-upstream: Add a CDAT table access DOE")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In build_cdat_table() we do:
*cdat_table = g_malloc0(sizeof(*cdat_table) * CXL_USP_CDAT_NUM_ENTRIES);
This is wrong because:
- cdat_table has type CDATSubHeader ***
- so *cdat_table has type CDATSubHeader **
- so the array we're allocating here should be items of type CDATSubHeader *
- but we pass sizeof(*cdat_table), which is sizeof(CDATSubHeader **),
implying that we're allocating an array of CDATSubHeader **
It happens that sizeof(CDATSubHeader **) == sizeof(CDATSubHeader *)
so nothing blows up, but this should be sizeof(**cdat_table).
Avoid this excessively hard-to-understand code by using
g_new0() instead, which will do the type checking for us.
While we're here, we can drop the useless check against failure,
as g_malloc0() and g_new0() never fail.
This fixes Coverity issue CID 1508120.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230718101327.1111374-1-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Introduce a CONFIG option to build the pcie-to-pci bridge. No
functional change since it's enabled per default for PCIE_PORT=y.
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Message-Id: <72b6599d-6b27-00b5-aac5-2ebc16a2e023@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The failure paths in CDAT file loading did not clear up properly.
Change to using g_auto_free and a local pointer for the buffer to
ensure this function has no side effects on error.
Also drop some unnecessary checks that can not fail.
Cleanup properly after a failure to load a CDAT file.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230421132020.7408-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previously, PXB_CXL_DEVICE, PXB_PCIE_DEVICE and PXB_DEVICE all
have PCI_DEVICE as their direct parent but share a common state
struct PXBDev. convert_to_pxb() is used to get the PXBDev
instance from which ever of these types it is called on.
This patch switches to an explicit hierarchy based on shared
functionality. To allow use of OBJECT_DECLARE_SIMPLE_TYPE()
whilst minimizing code changes, all types are renamed to have
the postfix _DEV rather than _DEVICE. The new heirarchy
has PXB_CXL_DEV with parent PXB_PCIE_DEV which in turn
has parent PXB_DEV which continues to have parent PCI_DEVICE.
This allows simple use of PXB_DEV() etc rather than a custom function
+ removal of duplicated properties and moving the CXL specific
elements out of struct PXBDev.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230420142750.6950-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reproduce issue with
configure --enable-qom-cast-debug ...
qemu-system-x86_64 -display none -machine q35,cxl=on -device pxb-cxl,bus=pcie.0
hw/pci-bridge/pci_expander_bridge.c:54:PXB_DEV: Object 0x5570e0b1ada0 is not an instance of type pxb
Aborted
The type conversion results in the right state structure, but PXB_DEV is
not a parent of PXB_CXL_DEV hence the error. Rather than directly
cleaning up the inheritance, this is the minimal fix which will be
followed by the cleanup.
Fixes: 154070eaf6 ("hw/pxb-cxl: Support passthrough HDM Decoders unless overridden")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230420142750.6950-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The CXL r3.0 specification allows for there to be no HDM decoders on CXL
Host Bridges if they have only a single root port. Instead, all accesses
directed to the host bridge (as specified in CXL Fixed Memory Windows)
are assumed to be routed to the single root port.
Linux currently assumes this implementation choice. So to simplify testing,
make QEMU emulation also default to no HDM decoders under these particular
circumstances, but provide a hdm_for_passthrough boolean option to have
HDM decoders as previously.
Technically this is breaking backwards compatibility, but given the only
known software stack used with the QEMU emulation is the Linux kernel
and this configuration did not work before this change, there are
unlikely to be any complaints that it now works. The option is retained
to allow testing of software that does allow for these HDM decoders to exist,
once someone writes it.
Reported-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
--
v2: Pick up and fix typo in tag from Fan Ni
Message-Id: <20230227153128.8164-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Done to avoid fixing ACPI route description of traditional PCI interrupts on q35
and because we should probably move with the times anyway.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Message-Id: <20230302133709.30373-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
We are missing necessary config write handling for AER emulation in
the CXL root port. Add it based on pcie_root_port.c
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Message-Id: <20230302133709.30373-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Fix capitalization difference between struct name and typedef.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230206172816.8201-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ICH9 is a south bridge which doesn't necessarily depend on x86, so move
it into the southbridge folder, analoguous to PIIX.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-13-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When ACPI PCI hotplug for Q35 was introduced (6.1), it was implemented
by hiding HPC capability on PCIE slot. That however led to a number of
regressions and to fix it, it was decided to keep HPC cap exposed
in ACPI PCI hotplug case and force guest in ACPI PCI hotplug mode
by other means [1].
That reduced meaning of x-native-hotplug to a compat knob [2] for
broken 6.1 machine type.
Rename property to match its current purpose.
1) 211afe5c69 (hw/i386/acpi-build: Deny control on PCIe Native Hot-plug in _OSC)
2) c318bef762 (hw/acpi/ich9: Add compat prop to keep HPC bit set for 6.1 machine type)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-10-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
hw/cxl/cxl.h uses the PXBDev structure tag instead of the typedef
name. The typedef name is defined in hw/pci/pci_bridge.h. Its
inclusion was dropped in the previous commit to break an inclusion
loop.
Move the typedef to hw/cxl/cxl.h, and use it there. Delete an extra
typedef in hw/pci-bridge/pci_expander_bridge.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/pci/pci_bridge.h and hw/cxl/cxl.h include each other.
Fortunately, breaking the loop is merely a matter of deleting
unnecessary includes from headers, and adding them back in places
where they are now missing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
and use cast to TYPE_PCI_BRIDGE instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221129101341.185621-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Code has not been used practically since its inception (2004)
f2aa58c6f4 UniNorth PCI bridge support
or maybe even earlier, but it was consuming contributors time
as QEMU was being rewritten.
Drop it for now. Whomever would like to actually
use the thing, can make sure it actually works/reintroduce
it back when there is a user.
PS:
I've stumbled upon this when replacing PCIDeviceClass::is_bridge
field with QOM cast to PCI_BRIDGE type. Unused DEC 21154
was the only one trying to use the field with plain PCIDevice.
It's not worth keeping the field around for the sake of the code
that was commented out 'forever'.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221129101341.185621-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert the TYPE_CXL_ROOT_PORT and TYPE_PNV_PHB_ROOT_PORT classes to
3-phase reset, so they don't need to use the deprecated
device_class_set_parent_reset() function any more.
We have to do both in the same commit, because they keep the
parent_reset field in their common parent class's class struct.
Note that pnv_phb_root_port_class_init() was pointlessly setting
dc->reset twice, once by calling device_class_set_parent_reset()
and once directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-5-peter.maydell@linaro.org
Convert the TYPE_PCIE_ROOT_PORT device to 3-phase reset; this is a
necessary precursor to converting any of its child classes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-4-peter.maydell@linaro.org
This Data Object Exchange Mailbox allows software to query the
latency and bandwidth between ports on the switch. For now
only provide information on routes between the upstream port and
each downstream port (not p2p).
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
--
Changes since v8: Mostly to match the type 3 equivalent
- Move enum out of function and give it a more descriptive namespace.
Message-Id: <20221014151045.24781-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Emulation of a simple CXL Switch downstream port.
The Device ID has been allocated for this use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220616145126.8002-3-Jonathan.Cameron@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An initial simple upstream port emulation to allow the creation
of CXL switches. The Device ID has been allocated for this use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220616145126.8002-2-Jonathan.Cameron@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the CXLState will no long be accessible via MachineState
at time of PXB_CXL realization, come back later from the machine specific
code to fill in the missing memory region setup. Only at this stage
is it possible to check if cxl=on, so that check is moved to this
later point.
Note that for multiple host bridges, the allocation order of the
register spaces is changed. This will be reflected in ACPI CEDT.
Stubs are added to handle case of CONFIG_PXB=n for machines that
call these functions.
The bus walking logic is common to all machines so add a utility
function + stub to cxl-host*.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Message-Id: <20220608145440.26106-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Paolo Bonzini requested this change to simplify the ongoing
effort to allow machine setup entirely via RPC.
Includes shortening the command line form cxl-fixed-memory-window
to cxl-fmw as the command lines are extremely long even with this
change.
The json change is needed to ensure that there is
a CXLFixedMemoryWindowOptionsList even though the actual
element in the json is never used. Similar to existing
SgxEpcProperties.
Update qemu-options.hx to reflect that this is now a -machine
parameter. The bulk of -M / -machine parameters are documented
under machine, so use that in preference to M.
Update cxl-test and bios-tables-test to reflect new parameters.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Message-Id: <20220608145440.26106-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Accessor to get hold of the cxl state for a CXL host bridge
without exposing the internals of the implementation.
Signed-off-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-32-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The CXL Early Discovery Table is defined in the CXL 2.0 specification as
a way for the OS to get CXL specific information from the system
firmware.
CXL 2.0 specification adds an _HID, ACPI0016, for CXL capable host
bridges, with a _CID of PNP0A08 (PCIe host bridge). CXL aware software
is able to use this initiate the proper _OSC method, and get the _UID
which is referenced by the CEDT. Therefore the existence of an ACPI0016
device allows a CXL aware driver perform the necessary actions. For a
CXL capable OS, this works. For a CXL unaware OS, this works.
CEDT awaremess requires more. The motivation for ACPI0017 is to provide
the possibility of having a Linux CXL module that can work on a legacy
Linux kernel. Linux core PCI/ACPI which won't be built as a module,
will see the _CID of PNP0A08 and bind a driver to it. If we later loaded
a driver for ACPI0016, Linux won't be able to bind it to the hardware
because it has already bound the PNP0A08 driver. The ACPI0017 device is
an opportunity to have an object to bind a driver will be used by a
Linux driver to walk the CXL topology and do everything that we would
have preferred to do with ACPI0016.
There is another motivation for an ACPI0017 device which isn't
implemented here. An operating system needs an attach point for a
non-volatile region provider that understands cross-hostbridge
interleaving. Since QEMU emulation doesn't support interleaving yet,
this is more important on the OS side, for now.
As of CXL 2.0 spec, only 1 sub structure is defined, the CXL Host Bridge
Structure (CHBS) which is primarily useful for telling the OS exactly
where the MMIO for the host bridge is.
Link: https://lore.kernel.org/linux-cxl/20210115034911.nkgpzc756d6qmjpl@intel.com/T/#t
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-26-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL host bridges themselves may have MMIO. Since host bridges don't have
a BAR they are treated as special for MMIO. This patch includes
i386/pc support.
Also hook up the device reset now that we have have the MMIO
space in which the results are visible.
Note that we duplicate the PCI express case for the aml_build but
the implementations will diverge when the CXL specific _OSC is
introduced.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-24-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds just enough of a root port implementation to be able to
enumerate root ports (creating the required DVSEC entries). What's not
here yet is the MMIO nor the ability to write some of the DVSEC entries.
This can be added with the qemu commandline by adding a rootport to a
specific CXL host bridge. For example:
-device cxl-rp,id=rp0,bus="cxl.0",addr=0.0,chassis=4
Like the host bridge patch, the ACPI tables aren't generated at this
point and so system software cannot use it.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-17-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This works like adding a typical pxb device, except the name is
'pxb-cxl' instead of 'pxb-pcie'. An example command line would be as
follows:
-device pxb-cxl,id=cxl.0,bus="pcie.0",bus_nr=1
A CXL PXB is backward compatible with PCIe. What this means in practice
is that an operating system that is unaware of CXL should still be able
to enumerate this topology as if it were PCIe.
One can create multiple CXL PXB host bridges, but a host bridge can only
be connected to the main root bus. Host bridges cannot appear elsewhere
in the topology.
Note that as of this patch, the ACPI tables needed for the host bridge
(specifically, an ACPI object in _SB named ACPI0016 and the CEDT) aren't
created. So while this patch internally creates it, it cannot be
properly used by an operating system or other system software.
Also necessary is to add an exception to scripts/device-crash-test
similar to that for exiting pxb as both must created on a PCIexpress
host bus.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan.Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-15-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The easiest way to differentiate a CXL bus, and a PCIE bus is using a
flag. A CXL bus, in hardware, is backward compatible with PCIE, and
therefore the code tries pretty hard to keep them in sync as much as
possible.
The other way to implement this would be to try to cast the bus to the
correct type. This is less code and useful for debugging via simply
looking at the flags.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-13-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This opens up the possibility for more types of expanders (other than
PCI and PCIe). We'll need this to create a CXL expander.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-12-Jonathan.Cameron@huawei.com>
Type name will be used in followup patch for cast check
in pcihp code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220301151200.3507298-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Wrong goto label, so msi cleanup would not occur if there is
an error in the ssvid initialization.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220218102303.7061-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Goto label is incorrect so msi cleanup would not occur if there is
an error in the ssvid initialization.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220218102303.7061-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pxb_map_irq_fn() handled the necessary removal of the swizzle
applied to the PXB interrupts by the bus to which it was attached
but neglected to apply the normal swizzle for PCI root ports
on the expander bridge.
Result of this was on ARM virt, the PME interrupts for a second
RP on a PXB instance were miss-routed to #45 rather than #46.
Tested with a selection of different configurations with 1 to 5
RP per PXB instance. Note on my x86 test setup the PME interrupts
are not triggered so I haven't been able to test this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-Id: <20220118174855.19325-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
DeviceState.id is a pointer to a string that is stored in the QemuOpts
object DeviceState.opts and freed together with it. We want to create
devices without going through QemuOpts in the future, so make this a
separately allocated string.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211008133442.141332-9-kwolf@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Q35 has now ACPI hotplug enabled by default for PCI(e) devices.
As opposed to native PCIe hotplug, guests like Fedora 34
will not assign IO range to pcie-root-ports not supporting
native hotplug, resulting into a regression.
Reproduce by:
qemu-bin -M q35 -device pcie-root-port,id=p1 -monitor stdio
device_add e1000,bus=p1
In the Guest OS the respective pcie-root-port will have the IO range
disabled.
Fix it by setting the "reserve-io" hint capability of the
pcie-root-ports so the firmware will allocate the IO range instead.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <20210802090057.1709775-1-marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
