Put correct values (depending on CPU arch) into IOR and ISR on fault.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Move functionality to set IOR and ISR on fault into own
function. This will be used by follow-up patches.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The value of unwind_breg may reference register %r0, but we need to avoid
accessing gr0 directly and use the value 0 instead.
At runtime I've seen unwind_breg being zero with the Linux kernel when
rfi is used to jump to smp_callin().
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Bruno Haible <bruno@clisp.org>
The various operating systems (e.g. Linux, NetBSD) have issues
mapping the power button when it's stored in page zero.
NetBSD even crashes, because it fails to map that page and then
accesses unmapped memory.
Since we now have a consistent memory mapping of PDC in 32-bit
and 64-bit address space (the lower 32-bits of the address are in
sync) the power button can be moved back to PDC space.
This patch fixes the power button on Linux, NetBSD and HP-UX.
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Bruno Haible <bruno@clisp.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Fix the address translation for PDC space on PA2.0 if PSW.W=0.
Basically, for any address in the 32-bit PDC range from 0xf0000000 to
0xf1000000 keep the lower 32-bits and just set the upper 32-bits to
0xfffffff0.
This mapping fixes the emulated power button in PDC space for 32- and
64-bit machines and is how the physical C3700 machine seems to map
PDC.
Figures H-10 and H-11 in the parisc2.0 spec [1] show that the 32-bit
region will be mapped somewhere into a higher and bigger 64-bit PDC
space. The start and end of this 64-bit space is defined by the
physical address bits. But the figures don't specifiy where exactly the
mapping will start inside that region. Tests on a real HP C3700
regarding the address of the power button indicate, that the lower
32-bits will stay the same though.
[1] https://parisc.wiki.kernel.org/images-parisc/7/73/Parisc2.0.pdf
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Bruno Haible <bruno@clisp.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
NetBSD accesses some astro and elroy registers which aren't accessed
by Linux yet. Add emulation for those registers to allow NetBSD to
boot further.
Please note that this patch is not sufficient to completely boot up
NetBSD on the 64-bit C3700 machine yet.
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: Bruno Haible <bruno@clisp.org>
Recognize the qemu --nodefaults option, which will disable the
following default devices on hppa:
- lsi53c895a SCSI controller,
- artist graphics card,
- LASI 82596 NIC,
- tulip PCI NIC,
- second serial PCI card,
- USB OHCI controller.
Adding this option is very useful to allow manual testing and
debugging of the other possible devices on the command line.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The physical hardware allows DIMMs of 4 MB size and above, allowing up
to 3840 MB of memory, but is restricted by setup code to 3 GB.
Increase the limit to allow up to the maximum amount of memory.
Btw. the memory area from 0xf000.0000 to 0xffff.ffff is reserved by
the architecture for firmware and I/O memory and can not be used for
standard memory.
An upcoming 64-bit SeaBIOS-hppa firmware will allow more than 3.75GB
on 64-bit HPPA64. In this case the ram_max for the pa20 case will change.
Signed-off-by: Helge Deller <deller@gmx.de>
Noticed-by: Nelson H. F. Beebe <beebe@math.utah.edu>
Fixes: b7746b1194 ("hw/hppa/machine: Restrict the total memory size to 3GB")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Bruno Haible <bruno@clisp.org>
- add LE microblaze test to avocado
- use modern snapshot=on to avoid trashing disk image
- use plain bool for fe_is_open
- various updates to qtest timeouts
- enable meson test timeouts
- tweak the readthedocs environment
- partially revert un-flaking x86_64
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmWhPccACgkQ+9DbCVqe
KkS5agf+OoW6HOitt34YeL6cGGtIKaxbta+Fs6jq+ucIbN63TmLTuKrmPiRNxjuo
Fj2Qvh9R7Tl7Q/a7ZAym0Fze7GtsvvsidkiQS4pmi9vYuJrhS734CxXHT8JS6zJr
ymQ0nGZODg1cVB4oAR9sXo/OwEQdDTSgKp8wdNr930fxYwokUKBUgcOqElu3SWHv
duSYDuaflnP5B8ZGbb1ZnOlwS9lZIHTwjZyN5J1YtxF0T8Ez4A+xseEOpQ/00MoE
Ecjdp3ELCxzOI+1U33Yni7ol//fxQpRKi+xf2fGIxhuSA3i32rmY5NWTvl7VwuS1
gXryjX2rukSujySP3vkdtTp0dmkbpg==
=ZuDd
-----END PGP SIGNATURE-----
Merge tag 'pull-testing-updates-120124-2' of https://gitlab.com/stsquad/qemu into staging
testing and misc updates
- add LE microblaze test to avocado
- use modern snapshot=on to avoid trashing disk image
- use plain bool for fe_is_open
- various updates to qtest timeouts
- enable meson test timeouts
- tweak the readthedocs environment
- partially revert un-flaking x86_64
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmWhPccACgkQ+9DbCVqe
# KkS5agf+OoW6HOitt34YeL6cGGtIKaxbta+Fs6jq+ucIbN63TmLTuKrmPiRNxjuo
# Fj2Qvh9R7Tl7Q/a7ZAym0Fze7GtsvvsidkiQS4pmi9vYuJrhS734CxXHT8JS6zJr
# ymQ0nGZODg1cVB4oAR9sXo/OwEQdDTSgKp8wdNr930fxYwokUKBUgcOqElu3SWHv
# duSYDuaflnP5B8ZGbb1ZnOlwS9lZIHTwjZyN5J1YtxF0T8Ez4A+xseEOpQ/00MoE
# Ecjdp3ELCxzOI+1U33Yni7ol//fxQpRKi+xf2fGIxhuSA3i32rmY5NWTvl7VwuS1
# gXryjX2rukSujySP3vkdtTp0dmkbpg==
# =ZuDd
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 12 Jan 2024 13:25:27 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* tag 'pull-testing-updates-120124-2' of https://gitlab.com/stsquad/qemu: (22 commits)
tests/avocado: partially revert unmasking of replay_linux tests
readthodocs: fully specify a build environment
mtest2make: stop disabling meson test timeouts
tests/fp: Bump fp-test-mulAdd test timeout to 3 minutes
tests/unit: Bump test-crypto-block test timeout to 5 minutes
tests/unit: Bump test-aio-multithread test timeout to 2 minutes
tests/qtest: Bump the device-introspect-test timeout to 12 minutes
qtest: bump bios-table-test timeout to 9 minutes
qtest: bump aspeed_smc-test timeout to 6 minutes
qtest: bump qos-test timeout to 2 minutes
qtest: bump boot-serial-test timeout to 3 minutes
qtest: bump prom-env-test timeout to 6 minutes
qtest: bump pxe-test timeout to 10 minutes
qtest: bump test-hmp timeout to 4 minutes
qtest: bump npcm7xx_pwm-test timeout to 5 minutes
qtest: bump qom-test timeout to 15 minutes
qtest: bump migration-test timeout to 8 minutes
qtest: bump min meson timeout to 60 seconds
chardev: use bool for fe_is_open
gitlab: include microblazeel in testing
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix device presence checking in the virtio-ccw qtest
* Support codespell checking in checkpatch.pl
* Fix emulation of LAE s390x instruction
* Work around htags bug when environment is large
* Some other small clean-ups here and there
-----BEGIN PGP SIGNATURE-----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=F/j2
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-01-11' of https://gitlab.com/thuth/qemu into staging
* Fix non-deterministic failures of the 'netdev-socket' qtest
* Fix device presence checking in the virtio-ccw qtest
* Support codespell checking in checkpatch.pl
* Fix emulation of LAE s390x instruction
* Work around htags bug when environment is large
* Some other small clean-ups here and there
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmWgHlgRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXAnBAAjQve/Jmfp9p8eQmswG7cl/a2TuJ59b9X
# SFRja2PprV/Wp4kxxEJX4er9F2+rlMusNL62LBp/QjZi9u4lCvCmuB7sMa0wEkjr
# BPPBrkxkAT+/8vhGpYg2GrxZv/UOLkycp3sjEp4v5yXWQw+OEBnkZZ+AuHddpnEr
# NKMKss71uQmccvuzD5FMDfbJQcSBD/yGPyFfDrv1RKreYRlbkEDVlcVoZpfoMwQY
# Pl167iDdmjVtsT+4wf8vHo5W/AYKDOjlV6AoujCnJVZnGx6BtDLiF/iNJ/VU1Ty5
# cRxySPT64HG+cGrbRqz9IjDvs++WW5EQn1jPY8NO2XFz3sney6Cs/pLKjqJY9S7P
# kfOXOBZG3zOI1kgd/CSR5b4szg4XvtTZaupczKiGOpYC9klf0oQNXGU5jXi3Csop
# Q332oUgiPeNdOx/4tXobFX6RwVCqLRYZbHx9RRYSxWlqJJPAB74/n+RZsmOtsxuJ
# RaiPKDmbVlslkUm78gIa5e6DMwDk2wmlkqa64W7VZxyqfQTRDPiPvfMGePkj6tmZ
# h9vUsELwwORlHpZyL08n0fzs3aeIYwzPwhfr+5iQZIawIp4Zqo8i8Lic/WfIlok9
# rmPIA0mjs1VtrUsroItw4NcY04xcVa7hkhz4EbkZROrfGamdkLuvbk2OKuOeoL0U
# lpgtQL6jA7E=
# =F/j2
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 11 Jan 2024 16:59:04 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-01-11' of https://gitlab.com/thuth/qemu:
.gitlab-ci.d/buildtest.yml: Work around htags bug when environment is large
tests/tcg/s390x: Test LOAD ADDRESS EXTENDED
target/s390x: Fix LAE setting a wrong access register
scripts/checkpatch: Support codespell checking
hw/s390x/ccw: Replace dirname() with g_path_get_dirname()
hw/s390x/ccw: Replace basename() with g_path_get_basename()
target/s390x/kvm/pv: Provide some more useful information if decryption fails
gitlab: fix s390x tag for avocado-system-centos
tests/qtest/virtio-ccw: Fix device presence checking
qtest: ensure netdev-socket tests have non-overlapping names
net: handle QIOTask completion to report useful error message
net: add explicit info about connecting/listening state
Revert "tests/qtest/netdev-socket: Raise connection timeout to 120 seconds"
Revert "osdep: add getloadavg"
Revert "netdev: set timeout depending on loadavg"
qtest: use correct boolean type for failover property
q800: move dp8393x_prom memory region to Q800MachineState
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are warning messages printed from tests/qtest/numa-test.c,
to complain the CPU cluster and NUMA node boundary is broken. Since
the broken boundary is expected, we don't want to see the warning
messages.
# cd /home/gavin/sandbox/qemu.main/build
# MALLOC_PERTURB_=255 QTEST_QEMU_BINARY=./qemu-system-aarch64 \
G_TEST_DBUS_DAEMON=../tests/dbus-vmstate-daemon.sh \
QTEST_QEMU_IMG=./qemu-img \
QTEST_QEMU_STORAGE_DAEMON_BINARY=./storage-daemon/qemu-storage-daemon \
tests/qtest/numa-test --tap -k
:
qemu-system-aarch64: warning: CPU-0 and CPU-4 in socket-0-cluster-0 \
have been associated with node-0 and node-1 respectively. \
It can cause OSes like Linux to misbehave
:
Skip the invalidation of CPU cluster and NUMA node boundary when
qtest is enabled, to avoid the warning messages.
Fixes: a494fdb715 ("numa: Validate cluster and NUMA node boundary if required")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It seems we were premature in declaring replay_linux.py fixed. The
x86_64 image still seems to hang occasionally. I've raised a new bug
to cover it:
https://gitlab.com/qemu-project/qemu/-/issues/2094
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This is now expected by rtd so I've expanded using their example as
22.04 is one of our supported platforms. I tried to work out if there
was an easy way to re-generate a requirements.txt from our
pythondeps.toml but in the end went for the easier solution.
Cc: <qemu-stable@nongnu.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231221174200.2693694-1-alex.bennee@linaro.org>
The mtest2make.py script passes the arg '-t 0' to 'meson test' which
disables all test timeouts. This is a major source of pain when running
in GitLab CI and a test gets stuck. It will stall until GitLab kills the
CI job. This leaves us with little easily consumable information about
the stalled test. The TAP format doesn't show the test name until it is
completed, and TAP output from multiple tests it interleaved. So we
have to analyse the log to figure out what tests had un-finished TAP
output present and thus infer which test case caused the hang. This is
very time consuming and error prone.
By allowing meson to kill stalled tests, we get a direct display of what
test program got stuck, which lets us more directly focus in on what
specific test case within the test program hung.
The other issue with disabling meson test timeouts by default is that it
makes it more likely that maintainers inadvertantly introduce slowdowns.
For example the recent-ish change that accidentally made migrate-test
take 15-20 minutes instead of around 1 minute.
The main risk of this change is that the individual test timeouts might
be too short to allow completion in high load scenarios. Thus, there is
likely to be some short term pain where we have to bump the timeouts for
certain tests to make them reliable enough. The preceeding few patches
raised the timeouts for all failures that were immediately apparent
in GitLab CI.
Even with the possible short term instability, this should still be a
net win for debuggability of failed CI pipelines over the long term.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230717182859.707658-13-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-17-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
When running the tests in slow mode with --enable-debug on a very loaded
system, the fp-test-mulAdd test can take longer than 2 minutes. Bump the
timeout to three minutes to make sure it passes in such situations, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-16-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
When running the tests in slow mode on a very loaded system and with
--enable-debug, the test-crypto-block can take longer than 4 minutes.
Bump the timeout to 5 minutes to make sure that it also passes in
such situations.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-15-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
When running the tests in slow mode on a very loaded system and with
--enable-debug, the test-aio-multithread can take longer than 1 minute.
Bump the timeout to two minutes to make sure that it also passes in
such situations.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-14-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
When running the test in slow mode on a very loaded system with the
arm/aarch64 target and with --enable-debug, it can take longer than
10 minutes to finish the introspection test. Bump the timeout to twelve
minutes to make sure that it also finishes in such situations.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-13-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This is reliably hitting the current 2 minute timeout in GitLab CI,
and for the TCI job, it even hits a 6 minute timeout.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20230717182859.707658-12-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-12-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
On a loaded system with --enable-debug, this test can take longer than
5 minutes. Raising the timeout to 6 minutes gives greater headroom for
such situations.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
[thuth: Increase the timeout to 6 minutes for very loaded systems]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-11-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The qos-test takes just under 1 minute in a --enable-debug
build. Bumping to 2 minutes will give more headroom.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230717182859.707658-10-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-10-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The boot-serial-test takes about 1 + 1/2 minutes in a --enable-debug
build. Bumping to 3 minutes will give more headroom.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230717182859.707658-9-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-9-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The prom-env-test can take more than 5 minutes in a --enable-debug
build on a loaded system. Bumping to 6 minutes will give more headroom.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
[thuth: Bump timeout to 6 minutes instead of 3]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-8-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The pxe-test uses the boot_sector_test() function, and that already
uses a timeout of 600 seconds. So adjust the timeout on the meson
side accordingly.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
[thuth: Bump timeout to 600s and adjust commit description]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-7-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The hmp test takes just under 3 minutes in a --enable-debug
build. Bumping to 4 minutes will give more headroom.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230717182859.707658-6-berrange@redhat.com>
[thuth: fix copy-n-paste error in the description]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-6-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The npcm7xx_pwm-test takes 3 & 1/2 minutes in a --enable-debug build.
Bumping to 5 minutes will give more headroom.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230717182859.707658-5-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-5-thuth@redhat.com>
[AJB: s/pwn/pwm]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The qom-test is periodically hitting the 5 minute timeout when running
on the aarch64 emulator under GitLab CI. With an --enable-debug build
it can take over 10 minutes for arm/aarch64 targets. Setting timeout
to 15 minutes gives enough headroom to hopefully make it reliable.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20230717182859.707658-4-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-4-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The migration test should take between 1 min 30 and 2 mins on reasonably
modern hardware. The test is not especially compute bound, rather its
running time is dominated by the guest RAM size relative to the
bandwidth cap, which forces each iteration to take at least 30 seconds.
None the less under high load conditions with multiple QEMU processes
spawned and competing with other parallel tests, the worst case running
time might be somewhat extended. Bumping the timeout to 8 minutes gives
us good headroom, while still catching stuck tests relatively quickly.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20230717182859.707658-3-berrange@redhat.com>
[thuth: Bump timeout to 8 minutes to make it work on very loaded systems, too]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-3-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Even some of the relatively fast qtests can sometimes hit the 30 second
timeout in GitLab CI under high parallelism/load conditions. Bump the
min to 60 seconds to give a higher margin for reliability.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20230717182859.707658-2-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215070357.10888-2-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The function qemu_chr_fe_init already treats be->fe_open as a bool and
if it acts like a bool it should be one. While we are at it make the
variable name more descriptive and add kdoc decorations.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231211145959.93759-1-alex.bennee@linaro.org>
This reverts aeb5f8f248 (gitlab: build the correct microblaze target)
now we actually have a little-endian test in avocado thanks to this
years advent calendar.
Message-Id: <20240103173349.398526-4-alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This ensures the rootfs is never permanently changed as we don't need
persistence between tests anyway.
Message-Id: <20240103173349.398526-3-alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We've already got a test for a big endian microblaze machine, but so
far we lack one for a little endian machine. Now that the QEMU advent
calendar featured such an image, we can test the little endian mode,
too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231215161851.71508-1-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Sometimes the CI "pages" job fails with a message like this from
htags:
$ htags -anT --tree-view=filetree -m qemu_init -t "Welcome to the QEMU sourcecode"
htags: Negative exec line limit = -371
This is due to a bug in hflags where if the environment is too large it
falls over:
https://lists.gnu.org/archive/html/bug-global/2024-01/msg00000.html
This happens to us because GitLab CI puts the commit message of the
commit under test into the CI_COMMIT_MESSAGE and/or CI_COMMIT_TAG_MESSAGE
environment variables, so the job will fail if the commit happens to
have a verbose commit message.
Work around the htags bug by unsetting these variables while running
htags.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2080
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240111125543.1573473-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This updates edk2 to git master as of today. This picks up a patch
(merged only yesterday, that's why this last-minute PR) which allows to
work around a bug in shim, and enables that workaround in the qemu
firmware builds.
This solves a real-world problem on arm hardware, walk over to
https://gitlab.com/qemu-project/qemu/-/issues/1990 to see the details.
Merging this firmware update that close to the 8.2 release clearly is
not without risks. If I get a 'no', I'm not going to complain.
That said I'm not aware of any bugs, and landing this in 8.2.0 would
make a bunch of folks hanging around in issue 1990 very happy.
Alternative plan would be to merge this after the release, give it some
time for testing, and assuming everything goes well schedule a backport
for 8.2.1
-----BEGIN PGP SIGNATURE-----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=bcZj
-----END PGP SIGNATURE-----
Merge tag 'firmware/edk2-20231213-pull-request' of https://gitlab.com/kraxel/qemu into staging
edk2: update to git snapshot (maybe for-8.2)
This updates edk2 to git master as of today. This picks up a patch
(merged only yesterday, that's why this last-minute PR) which allows to
work around a bug in shim, and enables that workaround in the qemu
firmware builds.
This solves a real-world problem on arm hardware, walk over to
https://gitlab.com/qemu-project/qemu/-/issues/1990 to see the details.
Merging this firmware update that close to the 8.2 release clearly is
not without risks. If I get a 'no', I'm not going to complain.
That said I'm not aware of any bugs, and landing this in 8.2.0 would
make a bunch of folks hanging around in issue 1990 very happy.
Alternative plan would be to merge this after the release, give it some
time for testing, and assuming everything goes well schedule a backport
for 8.2.1
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEEoDKM/7k6F6eZAf59TLbY7tPocTgFAmV5i70ACgkQTLbY7tPo
# cTg5mA//VDjGNmBYWhIhf5c7Z8+h1FspnqkxqResX3KgE2indCWkTlyZnCFGb7CO
# NgDiCR7xKMw9S1Cun14vTs/OK8BVFvmXGhTIgjecK+k6w6D8PtR4QvfXYUKxNajA
# Sd6reWAlojlgKOkpcrejrSSvtBTZqrJc8CrkowMR3FZXzD0GstUCMZ0jBvVhzlO6
# o9RMk0kbf+VNupsA+v9ZWPstMHXjLKs8v1eUqrc6LYOanY6mqQM5Wz9yWteUfrNp
# /0zShBrkmB+BgPoRQypphFdXRacP82fVXDMeTSbbXaReI0PR9MLKZnyk0UUkES6k
# BTtEVEM0cCAYLGaGFjHZVEpbrtFmVBisE0fLgdozsCU8SMCuxjNzXyj0HGRsJ7m4
# UQ+qGJLOR3Zx/Bnz3LLKOmWBlq6MQD5lYgxk3dwSPKzXTqun1ndlVKenJ3Z9fgXQ
# gibVbS/2fNylR9aoPSYkXnlE8l8vSo24sXIn8R2wX8rJ0xBc6bFDs1MKizzv2b9l
# YUeybDwgDvbbDLGSN4DgIeNSZxQBgNO/nmuFnx8jNxTqcNlCJFHO2jR7gPijj5ct
# ZPQQwLCCEIxD3OY3Dg94zXDm1EfWZQpNBFDD/83joJt/15Vu9GLsPqEs4QUdiQsp
# MO4Bd7HFavLSGsyX1rMe0yonWirbRX2uKYmyc+KwGjjS9LRGesU=
# =bcZj
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 13 Dec 2023 10:47:25 GMT
# gpg: using RSA key A0328CFFB93A17A79901FE7D4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* tag 'firmware/edk2-20231213-pull-request' of https://gitlab.com/kraxel/qemu:
tests/acpi: disallow tests/data/acpi/virt/SSDT.memhp changes
tests/acpi: update expected data files
edk2: update binaries to git snapshot
edk2: update build config, set PcdUninstallMemAttrProtocol = TRUE.
edk2: update to git snapshot
tests/acpi: allow tests/data/acpi/virt/SSDT.memhp changes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZZ/QKgAKCRBAov/yOSY+
34eqBADA48++Z9gETFNheLUHdYEaja2emn+gSaoHLFquyq/l53w8RfrUII+BzV1o
T7D8xjlVQldAYZzqQn2pQe2S7r4ggfeNmxGxwJbCTW9sooGMwBnU8+Ix3ruSet7K
gI+UHLU4oHk6jdrT384tux2EG+qUmlLN1c7j4G/z1OzKEwFv7Q==
=+Pi0
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20240111' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20240111
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZZ/QKgAKCRBAov/yOSY+
# 34eqBADA48++Z9gETFNheLUHdYEaja2emn+gSaoHLFquyq/l53w8RfrUII+BzV1o
# T7D8xjlVQldAYZzqQn2pQe2S7r4ggfeNmxGxwJbCTW9sooGMwBnU8+Ix3ruSet7K
# gI+UHLU4oHk6jdrT384tux2EG+qUmlLN1c7j4G/z1OzKEwFv7Q==
# =+Pi0
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 11 Jan 2024 11:25:30 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240111' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_extioi: Add vmstate post_load support
hw/intc/loongarch_extioi: Add dynamic cpu number support
hw/loongarch/virt: Set iocsr address space per-board rather than percpu
hw/intc/loongarch_ipi: Use MemTxAttrs interface for ipi ops
target/loongarch: Add loongarch kvm into meson build
target/loongarch: Implement set vcpu intr for kvm
target/loongarch: Restrict TCG-specific code
target/loongarch: Implement kvm_arch_handle_exit
target/loongarch: Implement kvm_arch_init_vcpu
target/loongarch: Implement kvm_arch_init function
target/loongarch: Implement kvm get/set registers
target/loongarch: Supplement vcpu env initial when vcpu reset
target/loongarch: Define some kvm_arch interfaces
linux-headers: Synchronize linux headers from linux v6.7.0-rc8
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a small test to prevent regressions. Userspace runs in primary
mode, so LAE should always set the access register to 0.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20240111092328.929421-3-iii@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
LAE should set the access register corresponding to the first operand,
instead, it always modifies access register 1.
Co-developed-by: Ido Plat <Ido.Plat@ibm.com>
Cc: qemu-stable@nongnu.org
Fixes: a1c7610a68 ("target-s390x: implement LAY and LAEY instructions")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-ID: <20240111092328.929421-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add two spelling check options (--codespell and --codespellfile) to
enhance spelling check through dictionary, which copied the Linux
kernel's implementation in checkpatch.pl.
This check uses the dictionary at "/usr/share/codespell/dictionary.txt"
by default, if there is no dictionary specified under this path, it
will look for the dictionary of python3's codespell (This requires user
to add python3's path in environment variable $PATH, and to install
codespell by "pip install codespell").
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Tested-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240105083848.267192-1-zhao1.liu@linux.intel.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
As commit 3e015d815b ("use g_path_get_basename instead of basename")
said, g_path_get_dirname() should be preferred over dirname() since
the former is a portable utility function that has the advantage of not
modifying the string argument.
Replace dirname() with g_path_get_dirname().
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20231221171921.57784-3-zhao1.liu@linux.intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
g_path_get_basename() is a portable utility function that has the
advantage of not modifying the string argument, so it should be
preferred over basename().
And also to avoid potential compile breakage with the Musl C library
similar to [1], replace basename() with g_path_get_basename().
[1]: https://lore.kernel.org/all/20231212010228.2701544-1-raj.khem@gmail.com/
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20231221171921.57784-2-zhao1.liu@linux.intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It's a common scenario to copy guest images from one host to another
to run the guest on the other machine. This (of course) does not work
with "secure execution" guests since they are encrypted with one certain
host key. However, if you still (accidentally) do it, you only get a
very user-unfriendly error message that looks like this:
qemu-system-s390x: KVM PV command 2 (KVM_PV_SET_SEC_PARMS) failed:
header rc 108 rrc 5 IOCTL rc: -22
Let's provide at least a somewhat nicer hint to the users so that they
are able to figure out what might have gone wrong.
Buglink: https://issues.redhat.com/browse/RHEL-18212
Message-ID: <20240110142916.850605-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There are elements sw_ipmap and sw_coremap, which is usd to speed
up irq injection flow. They are saved and restored in vmstate during
migration, indeed they can calculated from hw registers. Here
post_load is added for get sw_ipmap and sw_coremap from extioi hw
state.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-5-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
On LoongArch physical machine, one extioi interrupt controller only
supports 4 cpus. With processor more than 4 cpus, there are multiple
extioi interrupt controllers; if interrupts need to be routed to
other cpus, they are forwarded from extioi node0 to other extioi nodes.
On virt machine model, there is simple extioi interrupt device model.
All cpus can access register of extioi interrupt controller, however
interrupt can only be route to 4 vcpu for compatible with old kernel.
This patch adds dynamic cpu number support about extioi interrupt.
With old kernel legacy extioi model is used, however kernel can detect
and choose new route method in future, so that interrupt can be routed to
all vcpus.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-4-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
LoongArch system has iocsr address space, most iocsr registers are
per-board, however some iocsr register spaces banked for percpu such
as ipi mailbox and extioi interrupt status. For banked iocsr space,
each cpu has the same iocsr space, but separate data.
This patch changes iocsr address space per-board rather percpu,
for iocsr registers specified for cpu, MemTxAttrs.requester_id
can be parsed for the cpu. With this patches, the total address space
on board will be simple, only iocsr address space and system memory,
rather than the number of cpu and system memory.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
There are two interface pairs for MemoryRegionOps, read/write and
read_with_attrs/write_with_attrs. The later is better for ipi device
emulation since initial cpu can be parsed from attrs.requester_id.
And requester_id can be overrided for IOCSR_IPI_SEND and mail_send
function when it is to forward message to another vcpu.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Add kvm.c into meson.build to compile it when kvm
is configed. Meanwhile in meson.build, we set the
kvm_targets to loongarch64-softmmu when the cpu is
loongarch. And fix the compiling error when config
is enable-kvm,disable-tcg.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-10-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement loongarch kvm set vcpu interrupt interface,
when a irq is set in vcpu, we use the KVM_INTERRUPT
ioctl to set intr into kvm.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-ID: <20240105075804.1228596-9-zhaotianrui@loongson.cn>
[PMD: Split from bigger patch, part 2]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240110094152.52138-2-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
In preparation of supporting KVM in the next commit.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-ID: <20240105075804.1228596-9-zhaotianrui@loongson.cn>
[PMD: Split from bigger patch, part 1]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240110094152.52138-1-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement kvm_arch_handle_exit for loongarch. In this
function, the KVM_EXIT_LOONGARCH_IOCSR is handled,
we read or write the iocsr address space by the addr,
length and is_write argument in kvm_run.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-8-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
