We can safely allow a VM to be migrated with invtsc enabled if
tsc-khz is set explicitly, because:
* QEMU already refuses to start if it can't set the TSC frequency
to the configured value.
* Management software is already required to keep device
configuration (including CPU configuration) the same on
migration source and destination.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170108173234.25721-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of searching the table we have just built, we can check
the env->features field directly.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170108173234.25721-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Return the migration-safe field on query-cpu-definitions. All CPU
models in x86 are migration-safe except "host".
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170116181212.31565-1-ehabkost@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When CPU vendor is set to AMD, the AMD feature alias bits on
CPUID[0x80000001].EDX are already automatically copied from CPUID[1].EDX
on x86_cpu_realizefn(). When CPU vendor is Intel, those bits are
reserved and should be zero. On either case, those bits shouldn't be set
in the CPU model table.
Commit 726a8ff686 removed those
bits from most CPU models, but the Opteron_* entries still have
them. Remove the alias bits from Opteron_* too.
Add an assert() to x86_register_cpudef_type() to ensure we don't
make the same mistake again.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170113190057.6327-1-ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
For linux, page 0 is mapped as an execute-only gateway. A gateway
page is a special bit in the page table that allows a B,GATE insn
within that page to raise processor permissions. This is how system
calls are implemented for HPPA.
Rather than actually map anything here, or handle permissions at all,
implement the semantics of the actual linux syscall entry points.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The HPPA cpu has a unique form of predicated execution in which
almost any instruction can set the PSW[N] (or "nullify") bit,
which suppresses execution (and even decoding) of the following
instruction. Execution of a nullified insn clears the PSW[N] bit.
This adds a generic framework for branching over nullified insns,
or for sufficiently simple insns, transforming the writeback of
the result to a conditional move. In the process, we want to be
able to represent PSW[N] as a TCG condition, which implies management
of the related tcg temps.
Signed-off-by: Richard Henderson <rth@twiddle.net>
This is just about the minimum required to enable compilation
without actually executing any instructions. This contains the
HPPACPU structure and the required callbacks, the gdbstub, the
basic translation loop, and a translate_one function that always
results in an illegal instruction.
Signed-off-by: Richard Henderson <rth@twiddle.net>
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fzmu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170120-v2' into staging
First set of s390x patches for 2.9:
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
# gpg: Signature made Fri 20 Jan 2017 09:11:58 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170120-v2:
virtio-ccw: fix ring sizing
s390x/pci: merge msix init functions
s390x/pci: handle PCIBridge bus number
s390x/pci: use hashtable to look up zpci via fh
s390x/pci: PCI multibus bridge handling
s390x/pci: optimize calling s390_get_phb()
s390x/pci: change the device array to a list
s390x/pci: dynamically allocate iommu
s390x/pci: make S390PCIIOMMU inherit Object
s390x/kvm: use kvm_gsi_routing_enabled in flic
s390x: add compat machine for 2.9
s390x: remove double compat statement
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the ARM_FEATURE_EL2 bit on Cortex-A52 and
Cortex-A57, since this is all now sufficiently implemented
to work with the GICv3. We provide the usual CPU property
to disable it for backwards compatibility with the older
virt boards.
In this commit, we disable the EL2 feature on the
virt and ZynpMP boards, so there is no overall effect.
Another commit will expose a board-level property to
allow the user to enable EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-18-git-send-email-peter.maydell@linaro.org
The PSCI spec states that a CPU_ON call should cause the new
CPU to be started in the highest implemented Non-secure
exception level. We were incorrectly starting it at the
exception level of the caller, which happens to be correct
if EL2 is not implemented. Implement the correct logic
as described in the PSCI 1.0 spec section 6.4:
* if EL2 exists and SCR_EL3.HCE is set: start in EL2
* otherwise start in EL1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-17-git-send-email-peter.maydell@linaro.org
Add fields to the ARMCPU structure to allow CPU classes to
specify the configurable aspects of their GIC CPU interface.
In particular, the virtualization support allows different
values for number of list registers, priority bits and
preemption bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-6-git-send-email-peter.maydell@linaro.org
The GICv3 support for virtualization includes an outbound
maintenance interrupt signal which is asserted when the
CPU interface wants to signal to the hypervisor that it
needs attention. Expose this as an outbound GPIO line from
the CPU object which can be wired up as a physical interrupt
line by the board code (as we do already for the CPU timers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-4-git-send-email-peter.maydell@linaro.org
The DBGVCR_EL2 system register is needed to run a 32-bit
EL1 guest under a Linux EL2 64-bit hypervisor. Its only
purpose is to provide AArch64 with access to the state of
the DBGVCR AArch32 register. Since we only have a dummy
DBGVCR, implement a corresponding dummy DBGVCR32_EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
To run a VM in 32-bit EL1 our AArch32 interrupt handling code
needs to be able to cope with VIRQ and VFIQ exceptions.
These behave like IRQ and FIQ except that we don't need to try
to route them to Monitor mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
A function may recursively call device search functions or may call
serveral different device search function. Passing the S390pciState to
search functions as an argument instead of looking up it inside the
search functions lowers the number of calling s390_get_phb().
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Re-add the MacOSX/Darwin support:
Use the Intel HAX is kernel-based hardware acceleration module
(similar to KVM on Linux).
Based on the original "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com> from emu-2.2-release branch in
the external/qemu-android repository.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <81b85c3032da902e73e77302af508b4b1a7c0ead.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the Intel HAX is kernel-based hardware acceleration module for
Windows (similar to KVM on Linux).
Based on the "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <7b9cae28a0c379ab459c7a8545c9a39762bd394f.1484045952.git.vpalatin@chromium.org>
[Drop hax_populate_ram stub. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
That's a forward port of the core HAX interface code from the
emu-2.2-release branch in the external/qemu-android repository as used by
the Android emulator.
The original commit was "target/i386: Add Intel HAX to android emulator"
saying:
"""
Backport of 2b3098ff27bab079caab9b46b58546b5036f5c0c
from studio-1.4-dev into emu-master-dev
Intel HAX (harware acceleration) will enhance android emulator performance
in Windows and Mac OS X in the systems powered by Intel processors with
"Intel Hardware Accelerated Execution Manager" package installed when
user runs android emulator with Intel target.
Signed-off-by: David Chou <david.j.chou@intel.com>
"""
It has been modified to build and run along with the current code base.
The formatting has been fixed to go through scripts/checkpatch.pl,
and the DPRINTF macros have been updated to get the instanciations checked by
the compiler.
The FPU registers saving/restoring has been updated to match the current
QEMU registers layout.
The implementation has been simplified by doing the following modifications:
- removing the code for supporting the hardware without Unrestricted Guest (UG)
mode (including all the code to fallback on TCG emulation).
- not including the Darwin support (which is not yet debugged/tested).
- simplifying the initialization by removing the leftovers from the Android
specific code, then trimming down the remaining logic.
- removing the unused MemoryListener callbacks.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <e1023837f8d0e4c470f6c4a3bf643971b2bca5be.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are not needed since linux-headers/ provides up-to-date definitions.
The constants are in linux-headers/asm-powerpc/kvm.h.
The sole users, hw/intc/xics_kvm.c and target/ppc/kvm.c, include asm/kvm.h
via sysemu/kvm.h->linux/kvm.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In OpenSPARC T1+ TWINX ASIs in store instructions are aliased
with Block Initializing Store ASIs.
"UltraSPARC T1 Supplement Draft D2.1, 14 May 2007" describes them
in the chapter "5.9 Block Initializing Store ASIs"
Integer stores of all sizes are allowed with these ASIs.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
According to chapter 13.3 of the
UltraSPARC T1 Supplement to the UltraSPARC Architecture 2005,
only the sun4u format is available for data-access loads.
Store UA2005 entries in the sun4u format to simplify processing.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Implement the behavior described in the chapter 13.9.11 of
UltraSPARC T1™ Supplement to the UltraSPARC Architecture 2005:
"If a TLB Data-In replacement is attempted with all TLB
entries locked and valid, the last TLB entry (entry 63) is
replaced."
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Please note that QEMU doesn't impelement Real->Physical address
translation. The "Real Address" is always the "Physical Address".
Suggested-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Accordinf to UA2005, 9.3.3 "Address Space Identifiers",
"In hyperprivileged mode, all instruction fetches and loads and stores with implicit
ASIs use a physical address, regardless of the value of TL".
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
As described in Chapter 5.7.6 of the UltraSPARC Architecture 2005,
outstanding disrupting exceptions that are destined for privileged mode can only
cause a trap when the virtual processor is in nonprivileged or privileged mode and
PSTATE.ie = 1. At all other times, they are held pending.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Use explicit register pointers while accessing D/I-MMU registers.
Call cpu_unassigned_access on access to missing registers.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
while IMMU/DMMU is disabled
- ignore MMU-faults in hypervisorv mode or if CPU doesn't have hypervisor
- signal TT_INSN_REAL_TRANSLATION_MISS/TT_DATA_REAL_TRANSLATION_MISS otherwise
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
RER and WER are privileged instructions for accessing external
registers. External register address space is local to processor core.
There's no alignment requirements, addressable units are 32-bit wide
registers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYeOOmAAoJEPvQ2wlanipE3ZUH/Rsfpl23kXCMmqoXEIhWXy+h
yf8ARWCmpU6UKfwb+sH4vLegBfU56f62vVkGQ6oaaAbuyQ4SxCUlZGMO/rqY8/TE
m57aM+VfEE+bIdinAtLjFM24EVp/exMfkeutK7ItzLv7GwlrBos0J5veyCuyJ15q
pccV24jrpbJGilEeJ2GblKp3r2I3dInQGauOQhtoP3MNjHmYNSQD7noSbdN/JiTR
9H2eV700pg3ZPaSfO+CTVQN+cHjK1FC6qLi6916YZY9llnSOnDAegBYgbwE1RIBw
AULpWrezYveKy71eFhHVtGxnPeCJ8J4GVECMK0P0cdxzprIXFh1kZezyM4bxAGk=
=sboI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1' into staging
This is the same as the v3 posted except a re-base and a few extra signoffs
# gpg: Signature made Fri 13 Jan 2017 14:26:46 GMT
# gpg: using RSA key 0xFBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>"
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1:
cputlb: drop flush_global flag from tlb_flush
cpu_common_reset: wrap TCG specific code in tcg_enabled()
qom/cpu: move tlb_flush to cpu_common_reset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the useless is_external argument. Since the iohandler
AioContext is never used for block devices, aio_disable_external
is never called on it. This lets us remove stubs/iohandler.c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Configuration overlay does not explicitly say whether there are ICACHE
and DCACHE in the core. Current code uses XCHAL_[ID]CACHE_WAYS to detect
if corresponding cache option is enabled, but that's not correct: on
cores without cache these macros are defined as 1, not as 0.
Check XCHAL_[ID]CACHE_SIZE instead.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There's no point in continuing translating guest instructions once an
unconditional exception is thrown.
There's also no point in updating pc before any instruction is
translated, don't do it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Delimit each instruction that may access timers or IRQ state with
qemu_io_start/qemu_io_end, so that qemu-system-xtensa could be run with
-icount option.
Raise EXCP_YIELD after CCOMPARE reprogramming to let tcg_cpu_exec
recalculate how long this CPU is allowed to run.
RSR now may need to terminate TB, but it can't be done in RSR handler
because the same handler is used for XSR together with WSR handler, which
may also need to terminate TB. Change RSR and WSR handlers return type
to bool indicating whether TB termination is needed (RSR) or has been
done (WSR), and add TB termination after RSR/WSR dispatcher call.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Xtensa cores may have a register (CCOUNT) that counts core clock cycles.
It may also have a number of registers (CCOMPAREx); when CCOUNT value
passes the value of CCOMPAREx, timer interrupt x is raised.
Currently xtensa target counts a number of completed instructions and
assumes that for CCOUNT one instruction takes one cycle to complete.
It calls helper function to update CCOUNT register at every TB end and
raise timer interrupts. This scheme works very predictably and doesn't
have noticeable performance impact, but it is hard to use with multiple
synchronized processors, especially with coming MTTCG.
Derive CCOUNT from the virtual simulation time, QEMU_CLOCK_VIRTUAL.
Use native QEMU timers for CCOMPARE timers, one timer for each register.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
RUNSTALL signal stalls core execution while it's applied. It is widely
used in multicore configurations to control activity of additional
cores.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Xtensa cores may have two distinct addresses for the static vectors
group. Provide a function to select one of them.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
On 680x0 family only.
Address Register indirect With postincrement:
When using the stack pointer (A7) with byte size data, the register
is incremented by two.
Address Register indirect With predecrement:
When using the stack pointer (A7) with byte size data, the register
is decremented by two.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1484332593-16782-6-git-send-email-laurent@vivier.eu>
In these cases we must update the address register after
the operation.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1484332593-16782-4-git-send-email-laurent@vivier.eu>
gen_flush_flags() is setting unconditionally cc_op_synced to 1
and s->cc_op to CC_OP_FLAGS, whereas env->cc_op can be set
to something else by a previous tcg fragment.
We fix that by not setting cc_op_synced to 1
(except for gen_helper_flush_flags() that updates env->cc_op)
FIX: https://github.com/vivier/qemu-m68k/issues/19
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1484332593-16782-3-git-send-email-laurent@vivier.eu>
M680x0 bit operations with an immediate value use 9 bits of the 16bit
value, while coldfire ones use only 8 bits.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1484332593-16782-2-git-send-email-laurent@vivier.eu>
We have never has the concept of global TLB entries which would avoid
the flush so we never actually use this flag. Drop it and make clear
that tlb_flush is the sledge-hammer it has always been.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
[DG: ppc portions]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
It is a common thing amongst the various cpu reset functions want to
flush the SoftMMU's TLB entries. This is done either by calling
tlb_flush directly or by way of a general memset of the CPU
structure (sometimes both).
This moves the tlb_flush call to the common reset function and
additionally ensures it is only done for the CONFIG_SOFTMMU case and
when tcg is enabled.
In some target cases we add an empty end_of_reset_fields structure to the
target vCPU structure so have a clear end point for any memset which
is resetting value in the structure before CPU_COMMON (where the TLB
structures are).
While this is a nice clean-up in general it is also a precursor for
changes coming to cputlb for MTTCG where the clearing of entries
can't be done arbitrarily across vCPUs. Currently the cpu_reset
function is usually called from the context of another vCPU as the
architectural power up sequence is run. By using the cputlb API
functions we can ensure the right behaviour in the future.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
The new typename attribute on query-cpu-definitions will be used
to help management software use device-list-properties to check
which properties can be set using -cpu or -global for the CPU
model.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1479320499-29818-1-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In commit c52ab08aee,
the patch snippet for the "syscall" insn got applied to "iret".
Signed-off-by: Doug Evans <dje@google.com>
Message-Id: <f403045cde4049058c05446d5c04@google.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
If D[15] is != sign_ext(const4) then PC will be set to (PC +
zero_ext(disp4 + 16)).
[BK: fixed style errors]
Signed-off-by: Peer Adelt <peer.adelt@c-lab.de>
Message-Id: <1465314555-11501-5-git-send-email-peer.adelt@c-lab.de>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Puts the content of data register D[a] into E[c][63:32] and the
content of data register D[b] into E[c][31:0].
[BK: fix style error]
[BK: Allocate temporaries only when needed]
Signed-off-by: Peer Adelt <peer.adelt@c-lab.de>
Message-Id: <1465314555-11501-4-git-send-email-peer.adelt@c-lab.de>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Multiplies D[a] and D[b] and adds/subtracts the result to/from D[d].
The result is put in D[c]. All operands are floating-point numbers.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Converts a 32-bit floating point number to an unsigned int. The
result is rounded towards zero.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
