This support was limited to the Malta board, drop it.
I do not have a machine that can run VZ KVM, so I am assuming
that it works for -M malta as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221221091718.71844-1-philmd@linaro.org>
IRQRC[A:D] registers reset value is 0x80. We were forcing
the MIPS Malta machine routing to be able to boot a Linux
kernel without any bootloader.
We now have these registers initialized in the Malta machine
write_bootloader(), so we can use the correct reset values.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-4-philmd@linaro.org>
Linux kernel expects the northbridge & southbridge chipsets
configured by the BIOS firmware. We emulate that by writing
a tiny bootloader code in write_bootloader().
Upon introduction in commit 5c2b87e34d ("PIIX4 support"),
the PIIX4 configuration space included values specific to
the Malta board.
Set the Malta-specific IRQ routing values in the embedded
bootloader, so the next commit can remove the Malta specific
bits from the PIIX4 PCI-ISA bridge and make it generic
(matching the real hardware).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-3-philmd@linaro.org>
The PIIX4 PCI-ISA bridge function is always located at 10:0.
Since we want to re-use its address, add the PIIX4_PCI_DEVFN
definition.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-2-philmd@linaro.org>
Merge common code shared between write_bootloader() and
write_bootloader_nanomips() into bl_setup_gt64120_jump_kernel().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-12-philmd@linaro.org>
Part 5/5: Convert jumping to kernel
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-11-philmd@linaro.org>
Part 4/5: Convert GT64120 ISD base address setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-10-philmd@linaro.org>
Part 3/5: Convert PCI0 I/O BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-9-philmd@linaro.org>
Part 2/5: Convert PCI0 MEM0 BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-8-philmd@linaro.org>
Similarly to how commit 0c8427baf0 ("hw/mips/malta: Use bootloader
helper to set BAR registers") converted write_bootloader(), convert
the equivalent write_bootloader_nanomips(), allowing us to modify
the bootloader code more easily in the future.
Part 1/5: Convert PCI0 MEM1 BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-7-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-6-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-5-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-4-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211204533.85359-3-philmd@linaro.org>
It is irrelevant to the API what the buffers to fill are made of.
In particular, some MIPS ISA have 16-bit wide instructions.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-2-philmd@linaro.org>
The GT-64120 is a north-bridge, and it is not MIPS specific.
Move it with the other north-bridge devices.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221209151533.69516-8-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The single machine using this device explicitly sets its
endianness. We don't need to set a default. This allow us
to remove the target specificity from the build system.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20221209151533.69516-7-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Propagate the controller endianess from the machine, setting
the "cpu-little-endian" property.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221209151533.69516-6-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This device does not have to be TARGET-dependent.
Add a 'cpu_big_endian' property which sets the byte-swapping
options if required.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221220113436.14299-5-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221220113436.14299-4-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Per the comment in the Malta board, the [0x0000.0000-0x2000.0000]
range is decoded by the GT64120, so move the "empty_slot" there.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221209151533.69516-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221209151533.69516-2-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
GT64120's PCI endianness swapping works on little-endian hosts,
but doesn't on big-endian ones. Instead of complicating how
CFGADDR/CFGDATA registers deal with endianness, use the existing
MemoryRegionOps from hw/pci/pci_host.c. Doing so also reduce the
access to internal PCI_HOST_BRIDGE fields.
Map the PCI_HOST_BRIDGE MemoryRegionOps into the corresponding
CFGADDR/CFGDATA regions in the ISD MMIO and remove the unused
code in the current ISD read/write handlers.
Update the mapping when PCI0_CMD register is accessed (in case
the endianness is changed).
This allows using the GT64120 on a big-endian host (and boot
the MIPS Malta machine in little-endian).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-6-philmd@linaro.org>
Single registers access in ISD can produce multiple changes
in the address spaces. To reduce computational effort,
accumulate these as a single memory transaction.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-5-philmd@linaro.org>
The FPGA LEDs/ASCII display is mostly used by the bootloader
to show very low-level debug info. QEMU connects its output
to a character device backend, which is not very practical
to correlate with ASM instruction executed, interrupts or
MMIO accesses. Also, the display discard the previous states.
To ease bootloader debugging experience, add a pair of trace
events. Such events can be analyzed over time or diff-ed
between different runs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-4-philmd@linaro.org>
No need to refresh the ASCII bar when a LED is toggled
(and vice versa).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-3-philmd@linaro.org>
When using --disable-virglrenderer, QEMU still creates
hw-display-virtio-gpu-gl.so
hw-display-virtio-vga-gl.so
hw-display-virtio-gpu-pci-gl.so
but when these are loaded, they provide no functionality as the code
which registers types is not compiled in. Funtionally this is
relatively harmless, because QEMU is fine loading a module with no
types.
This is rather confusing for users and OS distro maintainers though,
as they think they have the GL functionality built, but in fact the
module they are looking at provides nothing of value.
The root cause is the use of 'when/if_true' rules when adding sources
to the module source set. If all the rules evaluate to false, then we
have declared the module, but not added anything to it. We need to
put declaration of the entire module inside a condition based on
existance of the 3rd party library deps that are mandatory.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1352
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221219125830.2369169-1-berrange@redhat.com>
[Do not check for pixman. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20221219130205.687815-3-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This API allows the accelerators to prevent vcpus from issuing
new ioctls while execting a critical section marked with the
accel_ioctl_inhibit_begin/end functions.
Note that all functions submitting ioctls must mark where the
ioctl is being called with accel_{cpu_}ioctl_begin/end().
This API requires the caller to always hold the BQL.
API documentation is in sysemu/accel-blocker.h
Internally, it uses a QemuLockCnt together with a per-CPU QemuLockCnt
(to minimize cache line bouncing) to keep avoid that new ioctls
run when the critical section starts, and a QemuEvent to wait
that all running ioctls finish.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221111154758.1372674-2-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the local Error variable with errp and ERRP_GUARD() and change
the return value to bool.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Remove an unnecessary local Error value in nvme_realize(). In the
process, change nvme_check_constraints() to return a bool.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* Rework and improvements of the EINTR handling by Nikita
* Deprecate the -no-hpet command line option
* Disable the qtests in the 32-bit Windows CI job again
* Some other misc fixes here and there
-----BEGIN PGP SIGNATURE-----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=D+Yw
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-01-09' of https://gitlab.com/thuth/qemu into staging
* s390x header clean-ups from Philippe
* Rework and improvements of the EINTR handling by Nikita
* Deprecate the -no-hpet command line option
* Disable the qtests in the 32-bit Windows CI job again
* Some other misc fixes here and there
# gpg: Signature made Mon 09 Jan 2023 14:21:19 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-01-09' of https://gitlab.com/thuth/qemu:
.gitlab-ci.d/windows: Do not run the qtests in the msys2-32bit job
error handling: Use RETRY_ON_EINTR() macro where applicable
Refactoring: refactor TFR() macro to RETRY_ON_EINTR()
docs/interop: Change the vnc-ledstate-Pseudo-encoding doc into .rst
i386: Deprecate the -no-hpet QEMU command line option
tests/qtest/bios-tables-test: Replace -no-hpet with hpet=off machine parameter
tests/readconfig: spice doesn't support unix socket on windows yet
target/s390x: Restrict sysemu/reset.h to system emulation
target/s390x/tcg/excp_helper: Restrict system headers to sysemu
target/s390x/tcg/misc_helper: Remove unused "memory.h" include
hw/s390x/pv: Restrict Protected Virtualization to sysemu
exec/memory: Expose memory_region_access_valid()
MAINTAINERS: Add MIPS-related docs and configs to the MIPS architecture section
tests/vm: Update get_default_jobs() to work on non-x86_64 non-KVM hosts
qemu-iotests/stream-under-throttle: do not shutdown QEMU
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a defined RETRY_ON_EINTR() macro in qemu/osdep.h
which handles the same while loop.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/415
Signed-off-by: Nikita Ivanov <nivanov@cloudlinux.com>
Message-Id: <20221023090422.242617-3-nivanov@cloudlinux.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[thuth: Dropped the hunk that changed socket_accept() in libqtest.c]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Instead of having hardware device poking into memory
internal API, expose memory_region_access_valid().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221217152454.96388-2-philmd@linaro.org>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmO6eGMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpoUIIALqC3UtJcK3AuAMbeqVokxl5CPwoeXMyi+rT
0QuN8m8dpBtJFpy3Vyq0afixOFmlwvORW5ye4QI97OyIhtLJq00buzQsgHjNoPo3
zN2L0BDyofDmfFHgCxcEbv2aAO8TaqRSHmKffEFmf8JDMDL9Ev1QvPTWHhfm2eJf
VKPHOtCA/3WXBD9JNfYJ0YuzCrrJaMhIO6/5tqv9yjMxWTfEFa1J2Sr2tWkRLuDk
FPfApy7afjI705Guv6PllZ3JdOMwf7iZaoBK6mSdCDSyi1xciYM0VeWi8SLD4qbM
N+9NkUQOIYS5ZC4BXrULy6HDUsECJ71I0pvHveX7nwbK6xPD4RQ=
=0tPe
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 08 Jan 2023 08:01:39 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (50 commits)
vhost-scsi: fix memleak of vsc->inflight
acpi: cpuhp: fix guest-visible maximum access size to the legacy reg block
tests: acpi: aarch64: Add *.topology tables
tests: acpi: aarch64: Add topology test for aarch64
tests: acpi: Add and whitelist *.topology blobs
tests: virt: Update expected ACPI tables for virt test
hw/acpi/aml-build: Only generate cluster node in PPTT when specified
tests: virt: Allow changes to PPTT test table
virtio-pci: fix proxy->vector_irqfd leak in virtio_pci_set_guest_notifiers
vdpa: commit all host notifier MRs in a single MR transaction
vhost: configure all host notifiers in a single MR transaction
vhost: simplify vhost_dev_enable_notifiers
vdpa: harden the error path if get_iova_range failed
vdpa-dev: get iova range explicitly
docs/devel: Rules on #include in headers
include: Include headers where needed
include/hw/virtio: Break inclusion loop
include/hw/cxl: Break inclusion loop cxl_pci.h and cxl_cdat_h
include/hw/pci: Include hw/pci/pci.h where needed
include/hw/pci: Split pci_device.h off pci.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prior to reading the shadow doorbell cq head, we have to update the
eventidx. Otherwise, we risk that the driver will skip an mmio doorbell
write. This happens on riscv64, as reported by Guenter.
Adding the missing update to the cq eventidx fixes the issue.
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Cc: qemu-riscv@nongnu.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The eventidx and doorbell value are not handling endianness correctly.
Fix this.
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Rename the trace events related to writing the event index and reading
the doorbell value to make it more clear that the event is associated
with an actual update (write or read respectively).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Replace various ->parent_obj use with the equivalent QOM accessors.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* Always send errors to logfile when daemonized (Greg)
* Add support for IDE CompactFlash card (Lubomir)
* First round of build system cleanups (myself)
* First round of feature removals (myself)
* Reduce "qemu/accel.h" inclusion (Philippe)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmO3Ym0UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNYmwf+LHEw+4T0fk1+2NfgIzH3+8s1EqDm
Ai56EjxO/p5NUptflXAnhn4P3LawswmmNE0ZIFFFBgwG5E9L+Jj/u5efuLu4uYPg
bboEBDn8nxSNN2l08u9TyS6kSWSxbwwrs7i2+V+4uQIlVIcCHu+A0vpXns4vWwY0
zZGF8CgJKDQdPIxdXrH8+6/xtadQ8uDkYsAWDiY/nhozCsCUTAZGTXWEQbHJLARI
Z4X+Cmz/NFB9G4ka6K/y0HbQw99KA8G/EMPUSglN0ya10yjpyzrmeI7IlIves+5U
8lhCZXyBhaV9GXlIK1vIgEXlHf83C19a+v0DpW0bpxK631n2VR5y3CArBg==
=2Koq
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* Atomic memslot updates for KVM (Emanuele, David)
* Always send errors to logfile when daemonized (Greg)
* Add support for IDE CompactFlash card (Lubomir)
* First round of build system cleanups (myself)
* First round of feature removals (myself)
* Reduce "qemu/accel.h" inclusion (Philippe)
# gpg: Signature made Thu 05 Jan 2023 23:51:09 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (24 commits)
i386: SGX: remove deprecated member of SGXInfo
target/i386: Add SGX aex-notify and EDECCSSA support
util: remove support -chardev tty and -chardev parport
util: remove support for hex numbers with a scaling suffix
KVM: remove support for kernel-irqchip=off
docs: do not talk about past removal as happening in the future
meson: accept relative symlinks in "meson introspect --installed" data
meson: cleanup compiler detection
meson: support meson 0.64 -Doptimization=plain
configure: test all warnings
tests/qapi-schema: remove Meson workaround
meson: cleanup dummy-cpus.c rules
meson: tweak hardening options for Windows
configure: remove backwards-compatibility and obsolete options
configure: preserve qemu-ga variables
configure: cleanup $cpu tests
configure: remove dead function
configure: remove useless write_c_skeleton
ide: Add "ide-cf" driver, a CompactFlash card
ide: Add 8-bit data mode
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is below memleak detected when to quit the qemu-system-x86_64 (with
vhost-scsi-pci).
(qemu) quit
=================================================================
==15568==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 40 byte(s) in 1 object(s) allocated from:
#0 0x7f00aec57917 in __interceptor_calloc (/lib64/libasan.so.6+0xb4917)
#1 0x7f00ada0d7b5 in g_malloc0 (/lib64/libglib-2.0.so.0+0x517b5)
#2 0x5648ffd38bac in vhost_scsi_start ../hw/scsi/vhost-scsi.c:92
#3 0x5648ffd38d52 in vhost_scsi_set_status ../hw/scsi/vhost-scsi.c:131
#4 0x5648ffda340e in virtio_set_status ../hw/virtio/virtio.c:2036
#5 0x5648ff8de281 in virtio_ioport_write ../hw/virtio/virtio-pci.c:431
#6 0x5648ff8deb29 in virtio_pci_config_write ../hw/virtio/virtio-pci.c:576
#7 0x5648ffe5c0c2 in memory_region_write_accessor ../softmmu/memory.c:493
#8 0x5648ffe5c424 in access_with_adjusted_size ../softmmu/memory.c:555
#9 0x5648ffe6428f in memory_region_dispatch_write ../softmmu/memory.c:1515
#10 0x5648ffe8613d in flatview_write_continue ../softmmu/physmem.c:2825
#11 0x5648ffe86490 in flatview_write ../softmmu/physmem.c:2867
#12 0x5648ffe86d9f in address_space_write ../softmmu/physmem.c:2963
#13 0x5648ffe86e57 in address_space_rw ../softmmu/physmem.c:2973
#14 0x5648fffbfb3d in kvm_handle_io ../accel/kvm/kvm-all.c:2639
#15 0x5648fffc0e0d in kvm_cpu_exec ../accel/kvm/kvm-all.c:2890
#16 0x5648fffc90a7 in kvm_vcpu_thread_fn ../accel/kvm/kvm-accel-ops.c:51
#17 0x56490042400a in qemu_thread_start ../util/qemu-thread-posix.c:505
#18 0x7f00ac3b6ea4 in start_thread (/lib64/libpthread.so.0+0x7ea4)
Free the vsc->inflight at the 'stop' path.
Fixes: b82526c7ee ("vhost-scsi: support inflight io track")
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Li Feng <fengli@smartx.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Message-Id: <20230104160433.21353-1-dongli.zhang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The modern ACPI CPU hotplug interface was introduced in the following
series (aa1dd39ca307..679dd1a957df), released in v2.7.0:
1 abd49bc2ed docs: update ACPI CPU hotplug spec with new protocol
2 16bcab97eb pc: piix4/ich9: add 'cpu-hotplug-legacy' property
3 5e1b5d9388 acpi: cpuhp: add CPU devices AML with _STA method
4 ac35f13ba8 pc: acpi: introduce AcpiDeviceIfClass.madt_cpu hook
5 d2238cb678 acpi: cpuhp: implement hot-add parts of CPU hotplug
interface
6 8872c25a26 acpi: cpuhp: implement hot-remove parts of CPU hotplug
interface
7 76623d00ae acpi: cpuhp: add cpu._OST handling
8 679dd1a957 pc: use new CPU hotplug interface since 2.7 machine type
Before patch#1, "docs/specs/acpi_cpu_hotplug.txt" only specified 1-byte
accesses for the hotplug register block. Patch#1 preserved the same
restriction for the legacy register block, but:
- it specified DWORD accesses for some of the modern registers,
- in particular, the switch from the legacy block to the modern block
would require a DWORD write to the *legacy* block.
The latter functionality was then implemented in cpu_status_write()
[hw/acpi/cpu_hotplug.c], in patch#8.
Unfortunately, all DWORD accesses depended on a dormant bug: the one
introduced in earlier commit a014ed07bd ("memory: accept mismatching
sizes in memory_region_access_valid", 2013-05-29); first released in
v1.6.0. Due to commit a014ed07bd, the DWORD accesses to the *legacy*
CPU hotplug register block would work in spite of the above series *not*
relaxing "valid.max_access_size = 1" in "hw/acpi/cpu_hotplug.c":
> static const MemoryRegionOps AcpiCpuHotplug_ops = {
> .read = cpu_status_read,
> .write = cpu_status_write,
> .endianness = DEVICE_LITTLE_ENDIAN,
> .valid = {
> .min_access_size = 1,
> .max_access_size = 1,
> },
> };
Later, in commits e6d0c3ce68 ("acpi: cpuhp: introduce 'Command data 2'
field", 2020-01-22) and ae340aa3d2 ("acpi: cpuhp: spec: add typical
usecases", 2020-01-22), first released in v5.0.0, the modern CPU hotplug
interface (including the documentation) was extended with another DWORD
*read* access, namely to the "Command data 2" register, which would be
important for the guest to confirm whether it managed to switch the
register block from legacy to modern.
This functionality too silently depended on the bug from commit
a014ed07bd.
In commit 5d971f9e67 ('memory: Revert "memory: accept mismatching sizes
in memory_region_access_valid"', 2020-06-26), first released in v5.1.0,
the bug from commit a014ed07bd was fixed (the commit was reverted).
That swiftly exposed the bug in "AcpiCpuHotplug_ops", still present from
the v2.7.0 series quoted at the top -- namely the fact that
"valid.max_access_size = 1" didn't match what the guest was supposed to
do, according to the spec ("docs/specs/acpi_cpu_hotplug.txt").
The symptom is that the "modern interface negotiation protocol"
described in commit ae340aa3d2:
> + Use following steps to detect and enable modern CPU hotplug interface:
> + 1. Store 0x0 to the 'CPU selector' register,
> + attempting to switch to modern mode
> + 2. Store 0x0 to the 'CPU selector' register,
> + to ensure valid selector value
> + 3. Store 0x0 to the 'Command field' register,
> + 4. Read the 'Command data 2' register.
> + If read value is 0x0, the modern interface is enabled.
> + Otherwise legacy or no CPU hotplug interface available
falls apart for the guest: steps 1 and 2 are lost, because they are DWORD
writes; so no switching happens. Step 3 (a single-byte write) is not
lost, but it has no effect; see the condition in cpu_status_write() in
patch#8. And step 4 *misleads* the guest into thinking that the switch
worked: the DWORD read is lost again -- it returns zero to the guest
without ever reaching the device model, so the guest never learns the
switch didn't work.
This means that guest behavior centered on the "Command data 2" register
worked *only* in the v5.0.0 release; it got effectively regressed in
v5.1.0.
To make things *even more* complicated, the breakage was (and remains, as
of today) visible with TCG acceleration only. Commit 5d971f9e67 makes
no difference with KVM acceleration -- the DWORD accesses still work,
despite "valid.max_access_size = 1".
As commit 5d971f9e67 suggests, fix the problem by raising
"valid.max_access_size" to 4 -- the spec now clearly instructs the guest
to perform DWORD accesses to the legacy register block too, for enabling
(and verifying!) the modern block. In order to keep compatibility for the
device model implementation though, set "impl.max_access_size = 1", so
that wide accesses be split before they reach the legacy read/write
handlers, like they always have been on KVM, and like they were on TCG
before 5d971f9e67 (v5.1.0).
Tested with:
- OVMF IA32 + qemu-system-i386, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32X64 + qemu-system-x86_64, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32 + qemu-system-i386, SMM enabled, using TCG accel; verified the
register block switch and the present/possible CPU counting through the
modern hotplug interface, during OVMF boot (bugfix test);
- I do not have any testcase (guest payload) for regression-testing CPU
hotplug through the *legacy* CPU hotplug register block.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: qemu-stable@nongnu.org
Ref: "IO port write width clamping differs between TCG and KVM"
Link: http://mid.mail-archive.com/aaedee84-d3ed-a4f9-21e7-d221a28d1683@redhat.com
Link: https://lists.gnu.org/archive/html/qemu-devel/2023-01/msg00199.html
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230105161804.82486-1-lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently we'll always generate a cluster node no matter user has
specified '-smp clusters=X' or not. Cluster is an optional level
and will participant the building of Linux scheduling domains and
only appears on a few platforms. It's unncessary to always build
it when it cannot reflect the real topology on platforms having no
cluster implementation and to avoid affecting the linux scheduling
domains in the VM. So only generate the cluster topology in ACPI
PPTT when the user has specified it explicitly in -smp.
Tested qemu-system-aarch64 with `-smp 8` and linux 6.1-rc1, without
this patch:
estuary:/sys/devices/system/cpu/cpu0/topology$ cat cluster_*
ff # cluster_cpus
0-7 # cluster_cpus_list
56 # cluster_id
with this patch:
estuary:/sys/devices/system/cpu/cpu0/topology$ cat cluster_*
ff # cluster_cpus
0-7 # cluster_cpus_list
36 # cluster_id, with no cluster node kernel will make it to
physical package id
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Tested-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Message-Id: <20221229065513.55652-3-yangyicong@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
proxy->vector_irqfd did not free when kvm_virtio_pci_vector_use or
msix_set_vector_notifiers failed in virtio_pci_set_guest_notifiers.
Fixes: 7d37d351
Signed-off-by: Lei Xiang <leixiang@kylinos.cn>
Tested-by: Zeng Chi <zengchi@kylinos.cn>
Suggested-by: Xie Ming <xieming@kylinos.cn>
Message-Id: <20221227081604.806415-1-leixiang@kylinos.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows the vhost-vdpa device to batch the setup of all its MRs of
host notifiers.
This significantly reduces the device starting time, e.g. the time spend
on setup the host notifier MRs reduce from 423ms to 32ms for a VM with
64 vCPUs and 3 vhost-vDPA generic devices (vdpa_sim_blk, 64vq per device).
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-4-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This allows the vhost device to batch the setup of all its host notifiers.
This significantly reduces the device starting time, e.g. the time spend
on enabling notifiers reduce from 376ms to 9.1ms for a VM with 64 vCPUs
and 3 vhost-vDPA generic devices (vdpa_sim_blk, 64vq per device)
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-3-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Simplify the error path in vhost_dev_enable_notifiers by using
vhost_dev_disable_notifiers directly.
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-2-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
