linux/arch/openrisc
Paul Gortmaker 8e8550ef01 openrisc: delete __cpuinit usage from all openrisc files
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit  -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings.  In any case, they are temporary and harmless.

This removes all the arch/openrisc uses of the __cpuinit macros from
all C files.  Currently openrisc does not have any __CPUINIT used in
assembly files.

[1] https://lkml.org/lkml/2013/5/20/589

Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2013-07-14 19:36:55 -04:00
..
boot/dts openrisc: use new common dtc rule 2012-12-03 17:17:48 -06:00
configs OpenRISC: Build infrastructure 2011-07-22 18:46:30 +02:00
include Merge branch 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k 2013-07-03 11:12:08 -07:00
kernel openrisc: delete __cpuinit usage from all openrisc files 2013-07-14 19:36:55 -04:00
lib ARCH: drivers remove __dev* attributes. 2013-01-03 15:57:13 -08:00
mm mm: invoke oom-killer from remaining unconverted page fault handlers 2013-07-09 10:33:20 -07:00
Kconfig consolidate per-arch stack overflow debugging options 2013-07-04 11:25:39 -07:00
Makefile openrisc: use new common dtc rule 2012-12-03 17:17:48 -06:00
README.openrisc OpenRISC: Miscellaneous 2011-07-22 18:46:41 +02:00
TODO.openrisc OpenRISC: Miscellaneous 2011-07-22 18:46:41 +02:00

OpenRISC Linux
==============

This is a port of Linux to the OpenRISC class of microprocessors; the initial
target architecture, specifically, is the 32-bit OpenRISC 1000 family (or1k).

For information about OpenRISC processors and ongoing development:

	website		http://openrisc.net

For more information about Linux on OpenRISC, please contact South Pole AB.

	email:		info@southpole.se

	website:	http://southpole.se
			http://southpoleconsulting.com

---------------------------------------------------------------------

Build instructions for OpenRISC toolchain and Linux
===================================================

In order to build and run Linux for OpenRISC, you'll need at least a basic
toolchain and, perhaps, the architectural simulator.  Steps to get these bits
in place are outlined here.

1)  The toolchain can be obtained from openrisc.net.  Instructions for building
a toolchain can be found at:

http://openrisc.net/toolchain-build.html

2) or1ksim (optional)

or1ksim is the architectural simulator which will allow you to actually run
your OpenRISC Linux kernel if you don't have an OpenRISC processor at hand.

	git clone git://openrisc.net/jonas/or1ksim-svn

	cd or1ksim
	./configure --prefix=$OPENRISC_PREFIX
	make
	make install

3)  Linux kernel

Build the kernel as usual

	make ARCH=openrisc defconfig
	make ARCH=openrisc

4)  Run in architectural simulator

Grab the or1ksim platform configuration file (from the or1ksim source) and
together with your freshly built vmlinux, run your kernel with the following
incantation:

	sim -f arch/openrisc/or1ksim.cfg vmlinux

---------------------------------------------------------------------

Terminology
===========

In the code, the following particles are used on symbols to limit the scope
to more or less specific processor implementations:

openrisc: the OpenRISC class of processors
or1k:     the OpenRISC 1000 family of processors
or1200:   the OpenRISC 1200 processor

---------------------------------------------------------------------

History
========

18. 11. 2003	Matjaz Breskvar (phoenix@bsemi.com)
	initial port of linux to OpenRISC/or32 architecture.
        all the core stuff is implemented and seams usable.

08. 12. 2003	Matjaz Breskvar (phoenix@bsemi.com)
	complete change of TLB miss handling.
	rewrite of exceptions handling.
	fully functional sash-3.6 in default initrd.
	a much improved version with changes all around.

10. 04. 2004	Matjaz Breskvar (phoenix@bsemi.com)
	alot of bugfixes all over.
	ethernet support, functional http and telnet servers.
	running many standard linux apps.

26. 06. 2004	Matjaz Breskvar (phoenix@bsemi.com)
	port to 2.6.x

30. 11. 2004	Matjaz Breskvar (phoenix@bsemi.com)
	lots of bugfixes and enhancments.
	added opencores framebuffer driver.

09. 10. 2010    Jonas Bonn (jonas@southpole.se)
	major rewrite to bring up to par with upstream Linux 2.6.36