Alias GMAC as ethernet0 so U-boot can fill in the MAC address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has the same GMAC found on the A20 SoC, except it has
an extra reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 SoC has a GMAC gigabit ethernet controller supporting
MII, GMII, RGMII modes. Add pin muxing options for these modes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add generic device tree for s5pv210 and s5pv210-pinctrl
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add I2S (Inter-IC Sound) dt node which supports 1-port
stereo (1 channels) IIS-bus for audio interface with DMA-based
operation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Tested-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds cros_ec to exynos5420-peach-pit and exynos5800-peach-pi,
including:
* The keyboard
* The i2c tunnel
* The tps65090 under the i2c tunnel
* The battery under the i2c tunnel
To add extra motivation, it should be noted that tps65090 is one of
the things needed to get display-related FETs turned on for pit and
pi.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch cleans a arm-pmu node up for exynos4. Only exynos4412 series
boards have four pmu interrupts. Rest of exynos4 boards, except 4412, have only
two pmu interrupts. Thus, we can define two interrupts in the
exynos4.dtsi and extends the interrupts only exynos4412.dtsi.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The pwm driver requires a clocks property referencing the pwm peripheral
clk.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Correct the typo error for the second "uhphs_clk".
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These properties are deprecated and no longer of any use.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add FlexCAN node for the two FlexCAN IP instances in Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add initial Rex Pro i.mx6dl board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with
cat zImage imx6dl-rex-basic.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with
cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch splits the M53EVK device tree file into a common SoM
part and an EVK part. This is needed to make it easier for users
of the SoM to put it into different, non-reference baseboard.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Instead of relying on defaults or bootloader settings, explicitly define
all pad settings.
This resolves reported issues of no analogue audio output.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The rev C1 Wandboard uses the Broadcom 4330 for WiFi and Bluetooth instead of
the 4329. This changes the PADS assigned for the control lines. Another
side effect of the change is that on the rev C1 board, usdhc driver can't
detect the chip presence correctly so usdhc2 now needs its 'non-removeable'
property removed.
So that rev B1 and earlier can continue to work, this patch splits the
board-specific definitions from imx6qdl-wandboard.dtsi into
imx6qdl-wandboard-revb1.dtsi and imx6qdl-wandboard-revc1.dtsi. The new files
include the original base imx6qdl-wandboard.dtsi which retains the common
definitions.
The existing imx6dl-wandboard.dts includes imx6qdl-wandboard-revc1.dtsi and
imx6dl-wandboard-revb1.dts (new) includes imx6qdl-wandboard-revb1.dtsi.
This makes the rev C1 board the new default. The same pattern is used for
imx6q-wandboard.dts.
So, from U-Boot on a WB-Quad you use imxq-wandboard-revb1.dtb for the older B1
board and imxq-wandboard.dtb for the current rev C1 board.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Per the binding doc imx-sata.txt, the first entry of clock-names should
be "sata" than anything else. Correct it for imx53 SATA node.
It works for now only because SATA driver gets clock by index so far.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit 98ea6ad2ed (ARM: dts: imx6: use imx51-ssi) the mx6 ssi is
compatible with imx51, so align all the mx6 variant ssi compatible strings as:
compatible = "fsl,<imx6-soc>-ssi", "fsl,imx51-ssi";
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use clock definitions in i.MX27 DTS files.
Additional changes included in this patch (imx27.dtsi):
- Fix IPG clock for UART6.
- Use EMI_AHB_GATE clock for WEIM.
- Added GPIO_IPG_GATE clock for GPIO nodes. Currently this clock is
not used by the driver, but it can be added in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The SDMA on imx6sl and imx6sx is more compatible with imx6q one than
imx35. Let's use "fsl,imx6q-sdma" instead of "fsl,imx35-sdma", so that
SDMA ROM script on imx6sl and imx6sx can work for audio driver just like
the case of imx6q.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Robin Gong <yibin.gong@freescale.com>
Like the other mx6 variants, we need to pass fsl,fifo-depth property in dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use the correct compatible string for sdma and also provide the sdma firmware
path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add support for the PCI express bus available on MX6 Data Modul
edm-qmx6 board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested by loading the g_ether module and doing a ping between mx25pdk and the
host PC via USB.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The AHB to IP bridges (AIPSTZ) allow fine grained access rights management.
Add both bridges to the DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch splits the M28EVK device tree file into a common SoM
part and an EVK part. This is needed to make it easier for users
of the SoM to put it into different, non-reference baseboard.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Without that fix, the board freeze during boot.
This appeared after the following commit:
496f065 ARM: i.MX: Use of_clk_get_by_name() for timer clocks for DT case.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:
imx-keypad 20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@02000000/kpp@020b8000
imx-keypad 20b8000.kpp: failed to build keymap
imx-keypad: probe of 20b8000.kpp failed with error -2
Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Spread-spectrum doesn't work with Cubox-i hardware. eSATA devices are
detected, but then fail on normal IO. Therefore, disable this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add the transmit level, boost and attenuation parameters necessary for
the eSATA interface on Cubox-i to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fix usbmisc compatible string so that usbmisc node can be found and USB
functionality can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx6sx iomuxc-gpr syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sx iomuxc-gpr syscon node.
This is necessary to enable SW workaround for ERR007265,
please refer to imx6_pm_common_init of arch/arm/mach-imx/pm-imx6.c
for detail.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch add support for the imx6dl based aristainetos board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
DRAM: 1 GiB
NAND: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The fixed-regulator's enable-active-high property
is needed to indicate that the GPIO regulator is
active high.
Before that the regulator state was inverted.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.
With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
All dtsi files where already moved to generic dma bindings. Remove the
old non-generic DMA properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
All imx5*.dtsi files define the generic dma bindings. Drop the old
non-generic fsl,ssi-dma-events.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Replace old ssi dma properties by the generic dma properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The other i.mx6 variants use "vddarm" as the name of the internal regulator
that powers the core. Use the same convention here for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The S/PDIF rxtx4 and rxtx6 clock inputs are "ESAI_HCKT" and "MLB clock",
respectively, according to the SoC documentation, and they are currently
mapped to clocks "esai" and "mlb".
However, they do not seem to actually work correctly. Testing on a
Cubox-i system with fsl_spdif driver forced to select one of those as
input will result in I/O errors on audio playback, which I believe means
missing clock signal.
Possibly the "ESAI_HCKT" and "MLB clock" refer to some other clocks
related to ESAI and MLB, or we are missing something else.
Since audio playback will not work if fsl_spdif selects these clocks
(which happens rarely), set the inputs do dummy clocks, at least for
now.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The rxtx2 clock of i.MX6 S/PDIF is currently set to "asrc" clock.
However, according to SoC documentation, rxtx2 is connected to
ASRC_EXT_CLK, a different external clock.
Testing on Cubox-i system seems to confirm that: when fsl_spdif is
forced to select rxtx2 as input clock, audio playback fails with an I/O
error.
Set rxtx2 to the dummy clock by default to prevent fsl_spdif from
selecting it.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are five distinct module types with either i.MX6Q or i.MX6DL and
LVDS or LCD display interface and one DTS file for a complete system
with an i.MX6DL based TX6 module and a baseboard mounted on the back
of a display (imx6dl-tx6dl-comtft.dts).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 2.5V VDD_ETH_IO voltage supplied by the DA9063 LDO4 is used
to power the KSZ9031 PHY DVDDH input and to pull the necessary
pins (including bootstrap pins) high.
It also powers the i.MX6 NVCC_RGMII and NVCC_ENET inputs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx6dl dts supports both DualLite and Solo CPU variants
The imx6q dts supports both Dual and Quad CPU variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The PWM3 pinmux configuration conflicts with gpio 3.28. Introduce a regulator
for mmc0 so that it conflicts with the pwm driver and fails gracefully. The
kernel will then able to access mmc0 normally.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
GPIO4_9 is used as ECSPI1 chip select and it needs to be configured as GPIO.
Configure the pin functionality explicitly in the dts file instead of relying
on the fact that it comes configured as GPIO from POR or from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch replaces the "cs-gpio" from "controller-data" node
as was specified in the old binding and uses the standard
"cs-gpios" property expected by the SPI core as is defined now
in the spi-s3c64xx driver DT binding.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Keystone 2 has MDIO HW block which are compatible
to Davinci SoCs:
See "Gigabit Ethernet (GbE) Switch Subsystem"
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
Hence, add corresponding DT entry for Keystone 2.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tegra DSI support has been fixed to support continuous clock behavior that
the panel used on SHIELD requires, so finally add its device tree node
since it is functional.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The property for enabling external rail control on the AS3722 is
ams,ext-control, not ams,external-control. Since the external rail
control property was previously being ignored, LP1 suspend on these
boards wasn't actually turning the CPU rail off at all.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign lanes to the XUSB pads as used on the Jetson TK1.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device tree node in the SoC file contains only the resources (such
as registers, resets, ...) but none of the lane assignment information
since that's board specific and belongs in the board file.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Input had been disabled by mistake on these pins, leading to issues with
SDIO devices like the Wifi module not being probed or random errors
occuring on the SD card.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The pinmux subsystem complained that the nvidia,low-power-mode property
is not supported by the sdio1, sdio3 and gma drive groups. In addition
gma also does not support nvidia,drive-type. Remove these properties so
the pinmux configuration can properly be applied.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This migration is required for continued PCIe operation after commit
d3c7e24b84fc "PCI: tegra: Implement accurate power supply scheme".
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[swarren: added commit subject and shortened hash]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable the RGB output and add the panel definition to the Medcom Wide
DTS. Also add a label to the backlight defintion to reference it in
the panel definition.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Currently the Tamonten DTS define a fixed regulator for the 5V supply.
However this regulator is in fact on the base board. Fix this by
properly defining the regulators found on the base boards.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds the device tree to support Toradex Apalis T30, a
computer on module which can be used on different carrier boards.
The module consists of a Tegra 3 SoC, two PMICs, 1 or 2 GB of DDR3L
RAM, eMMC, an LM95245 temperature sensor chip, an i210 resp. i211
gigabit Ethernet controller, an STMPE811 ADC/touch controller as well
as two MCP2515 CAN controllers. Furthermore, there is an SGTL5000 audio
codec which is not yet supported. Anything that is not self contained
on the module is disabled by default.
The device tree for the Evaluation Board includes the modules device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
While at it also add the device tree binding documentation for Apalis
T30.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[swarren: fixed some node sort orders]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The eMMC is soldered to the board, reflect this in the DT.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Turn on the HDA controller in Venice2, it is used for HDMI audio.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add a device node for the HDA controller found on Tegra124.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the EC i2c tunnel (and devices under it) to the
tegra124-venice2 device tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add efuse and apbmisc bindings for Tegra20, Tegra30, Tegra114 and
Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to support dynamic frequency scaling:
* the cpuclk Device Tree node needs to be updated to describe a
second set of registers describing the PMU DFS registers.
* the clock-latency property of the CPUs must be filled, otherwise
the ondemand and conservative cpufreq governors refuse to work. The
latency is high because the cost of a frequency transition is quite
high on those CPUs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404920715-19834-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The CA9 MPcore SoC Control block is a set of registers that allows to
configure certain internal aspects of the core blocks of the SoC
(Cortex-A9, L2 cache controller, etc.). In most cases, the default
values are fine so they aren't many reasons to touch those registers,
but there is one exception: to support cpuidle on Armada 38x, we need
to modify the value of the CA9 MPcore Reset Control register.
Therefore, this commit adds a new Device Tree binding for this
hardware block, and uses this new binding for the Armada 38x Device
Tree file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Link: https://lkml.kernel.org/r/1404913221-17343-11-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Display domain is removed due to instability issues. Explaining
the problem below:
exynos_init_late triggers the pm_genpd_poweroff_unused which powers
off the unused power domains. This call hits before the trigger to
deferred probes.
DRM DP Panel defers the probe due to supply get failure. By the time,
deferred probe is scheduled again, Display Power Domain is powered
off by pm_genpd_poweroff_unused.
FIMD and DP drivers are accessing registers during Probe and Bind
callbacks. If display domain is enabled/disabled around register
accesses, display domain gets unstable and we are getting Power Domain
Disable fail notification. Increasing the Timeout also didn't help.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add MAX98090 audio codec, I2S interface and the sound complex
nodes to enable audio on Odroid-X2/U3 boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
TFLASH (SDHCI2 controller) uses internal card detect line, but it looks
that the driver fails to operate it properly. Use GPIO interrupt on
SD_CDn line for detecting SD card state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for simple GPIO-based button availabled on
Exynos4 based Odroid boards. All supported boards have POWER button,
which has been defined in exynos4412-odroid-common.dtsi. X/X2 boards
also have additional user-configurable button which has been mapped to
KEY_HOME. All defined keys have been marked as possible wakeup source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On Odroid U2/U3 BUCK8 is used for providing power to also to P3V3
source, which is also connected to LAN9730 chip's nRESET signal. To
reset lan chip on system reboot, the BUCK8 output should not be used in
'always on' mode. This change has no impact on X/X2 boards.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves some parts of exynos4412-odroidx.dts to common
exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and
U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz
instead of 1.4GHz), while U2/U3 differs from X2 by different way of
routing signals to host USB hub. It also lacks some hw modules not yet
supported by those dts files (i.e. LCD & touch panel).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Last megabyte of RAM is used by secure firmware and should not be accessed
by Linux kernel, so correct available memory size in DTS file.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds basic support for USB modules (host and device) on
OdroidX board.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[removed incorrect port@2 node]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for common hardware modules available on all
Exynos4412-based Odroid boards, which already have complete support in
mainline kernel. This includes secure firmware calls, watchdog, g2d and
fimc (mem2mem) multimedia accelerators.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds port sub-nodes to exynos4 ehci and ohci modules, which
are required by recently merged new exynos4 usb2 phy support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake. If we don't set it to anything then
the TPM will be reset. U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything. It will get pulled back high again during a
normal warm reset when it will default back to an input.
To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake. If we don't set it to anything then
the TPM will be reset. U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything. It will get pulled back high again during a
normal warm reset when it will default back to an input.
To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
DRA7xx has 13 system mailboxes, and is present on both the
DRA72x and DRA74x family of SoCs. Add the DT nodes for all
these 13 mailboxes. Except for mailbox 1, all other mailboxes
do not have interrupts mapped into the MPU GIC by default.
All the mailboxes have been disabled and the interrupts
property information is left out intentionally for now,
because of the dependencies against the crossbar driver.
These mailboxes can be enabled when a usecase arises
and the crossbar driver dependencies are met.
NOTE: The mailbox 1 has different number of mailbox fifos
and IP interrupts compared to the remaining 12 mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox DT node for AM4372 is enabled and is corrected to
remove some properties that have crept in by mistake.
Fixes: 9e3269b (ARM: dts: AM4372: Add L2, EDMA, mailbox, MMC and SHAM nodes)
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox DT node data has been added for AM33xx device.
The mailbox IP in AM33xx is similar to the version found in
OMAP4+ devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox DT node data has been added for OMAP44xx
devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The number of mailbox fifos and users (IP interrupts) are added
to the Mailbox DT nodes on OMAP2420, OMAP2430, OMAP3, and OMAP5
family of SoCs through the DT properties "ti,mbox-num-fifos" and
"ti,mbox-num-users" properties. This data represents the same data
that used to be represented in hwmod attribute data through the
.num_fifos and .num_users fields previously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses twl6040 codec connected via McPDM link. McBSP1 and McBSP2 can
be used for FM/BT.
At the same time move the pinctrl handling to the correct place - under the
corresponding nodes.
Audio connectors on the board:
Headset in/out
Stereo Line out
Stereo Line in.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses twl6040 as audio codec. Move the corresponding pinctrl as
well under the node.
twl6040 needs 32k clock from palams.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added dt data for PCIe controller. This node contains dt data for
both the DRA7 part of designware controller and for the designware core.
The documention for this node can be found @ ../bindings/pci/ti-pci.txt.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added dt data for PCIe PHY as a child node of ocp2scp3.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt.
26.3.3 PCIe Shared PHY Subsystem Integration in vE of DRA7xx ES1.0
describes the PCIe PHY subsystem-related components integrated in the device.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added dt data for PCIe PHY control module used by PCIe PHY.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added missing clocks used by second instance of PCIe PHY.
The documention for this nodes can be found @ ../bindings/clock/ti/gate.txt.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two instances of PCIe PHY in DRA7xx. So renamed
optfclk_pciephy_32khz, optfclk_pciephy_clk and optfclk_pciephy_div_clk to
optfclk_pciephy1_32khz, optfclk_pciephy1_clk and optfclk_pciephy1_div_clk
respectively. This is needed for adding the clocks for second PCIe PHY
instance.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added missing 32KHz clock used by PCIe PHY.
Figure 26-19. PCIe PHY Subsystem Integration in vE of DRA7xx ES1.0 TRM shows
32KHz is used by PCIe PHY.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
from dpll_pcie_ref_ck.
Figure 26-22. DPLL_PCIE_REF Functional Block Diagram in vE of DRA7xx ES1.0 TRM
shows the signal name for the output of post divider (M2) is CLKOUTLDO.
Figure 26-21. PCIe PHY Clock Generator Overview shows CLKOUTLDO is used as
input to apll mux.
So the actual output of dpll is dpll_pcie_ref_m2ldo_ck which is also the input
of apll.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add divider table to optfclk_pciephy_div clock. The 8th bit of
CM_CLKMODE_APLL_PCIE can be programmed to either 0x0 or 0x1
based on if the divider value is 0x2 or 0x1.
Figure 26-21. PCIe PHY Clock Generator Overview in vE of DRA7xx ES1.0 shows the
block diagram of Clock Generator Subsystem of PCIe PHY module. The divider
value if '1' should be programmed in order to get the correct
PCIE_PHY_DIV_GCLK frequency (2.5GHz).
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With sun8i PRCM support available, we can add the PRCM clock and
reset controller nodes to the DTSI. Also update R_UART's clock
phandle and add it's reset control phandle.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
add #reset-cells to socfpga.dtsi. This was missing from the
latest updates and caused the socfpga reset controller to fail
to load like so:
ffd05000.rstmgr: /soc/rstmgr@ffd05000 missing #reset-cells property
probe of ffd05000.rstmgr failed with error -22
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds necessary DT nodes for pcie controllers and miphys for SPEAr13xx
SoCs.
SPEAr1310 has 3 PCIe ports and SPEAr1340 has 1, which are multiplexed with
ahci/sata pins. By default evaluation board of both controller works in ahci
mode. Because of this, these nodes are marked "disabled" by default.
In order to use pcie controller on evaluation boards do necessary modifications
on board and enable (By replacing "disabled" with "okay") pcie and miphy from
respective 'evb' dtsi file.
Phy specific initialization was previously done from spear1340.c, which isn't
required anymore as we have separate drivers for it. Remove it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
[viresh: fixed logs/cclist/checkpatch warnings, clubbed multiple patches into one]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr SOCs have some miscellaneous registers which are used to configure
peripheral.
This patch adds dt node and binding information for this block.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Cc: devicetree@vger.kernel.org
[viresh: fixed logs/cclist]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that all boards have been converted to DT and all the support code
lives in mach-mvebu, we can remove mach-kirkwood.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1405028192-9623-2-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT support for the LaCie NAS d2 Network v2 (d2net_v2).
Most of the hardware characteristics are shared with the 2Big and 5Big
Network v2 boards.
- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-3-git-send-email-simon.guinot@sequanux.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The d2 Network v2 board (d2net_v2) shares a lot of hardware
characteristics with the 2Big and 5Big Network v2 boards. This patch
prepares the kirkwood-netxbig.dtsi file in order to allow to include it
from the d2net_v2 DTS file. The DT nodes only relevant for the 2Big and
5Big Network v2 boards are moved into their respective DTS files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-2-git-send-email-simon.guinot@sequanux.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* Consistently use tabs for indentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2i0p
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7779-multiplatform3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Third Round of Renesas ARM Based SoC r8a7779-multiplatform Updates
for v3.17" from Simon Horman:
- Consistently use tabs for indentation
* tag 'renesas-r8a7779-multiplatform3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen: Consistently use tabs for indentation
Signed-off-by: Olof Johansson <olof@lixom.net>
some constification from static code analysis.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmbF
-----END PGP SIGNATURE-----
Merge tag 'ux500-core-for-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
Merge "Ux500 core changes for v3.17 take 1" from Linus Walleij:
Some minor cleanups to the Ux500 core. DT-only probe path and
some constification from static code analysis.
* tag 'ux500-core-for-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: remove pointless cache setup complexity
ARM: ux500: storage class should be before const qualifier
ARM: ux500: Staticize ab8505_regulators
ARM: ux500: Staticize local symbols in cpu-db8500.c
ARM: ux500: Staticise ux500_soc_attr
+ Linux 3.16-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add regulators to STMPE expanders
- Add proper DMA channels for all SD/MMC blocks
- Add sensors to the device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLY8
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Ux500 devicetree changes for v3.17" from Linus Walleij:
Ux500 device tree patches for v3.17:
- Add regulators to STMPE expanders
- Add proper DMA channels for all SD/MMC blocks
- Add sensors to the device tree
* tag 'ux500-devicetree-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: add misc sensors to the device trees
ARM: ux500: add some DB8500 DMA channel info
ARM: ux500: add VCC and VIO regulators to STMPE IC
+ Linux 3.16-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=didu
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:
Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
on/off, its regarding clock source will be reset and it causes
a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
system failure will be happened on other exynos SoCs.
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: dts: Update the parent for Audss clocks in Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
* Extend hardware coverage
- Add DVC support for sound nodes on r8a7791 and r8a7790
- Enable internal PCI on r8a7790/lager
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6laJ
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v3.17" from Simon
Horman:
- Extend hardware coverage
* Add DVC support for sound nodes on r8a7791 and r8a7790
* Enable internal PCI on r8a7790/lager
* tag 'renesas-dt2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: add DVC support for sound node on DTSI
ARM: shmobile: r8a7790: add DVC support for sound node on DTSI
ARM: shmobile: lager: enable internal PCI
ARM: shmobile: r8a7790: add internal PCI bridge nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This describes all of the SCIF hardware of the sh73a0.
Each node is disabled and may be enabled as necessary
by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the SCIF hardware of the r8a7740.
Each node is disabled and may be enabled as necessary
by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the SCIF hardware of the r8a73a4.
Each node is disabled and may be enabled as necessary
by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Initialise SCIF device using DT when booting bockw
using DT reference.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the SCIF hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pads for PB0-PB3, PC0-PC4, PE26-PE31 and PF24-PF31 does not exist on
the i.MX27 SOC. There is no reason to define them, the presence of
such definitions in the DTS files is a bug.
This patch removes these nonexistent pad definitions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Lager board, i2c and iic cores can be interchanged since they can be
muxed to the same wires. Commit e489c2a9bc
("ARM: shmobile: lager: enable i2c devices") activated the i2c cores,
yet the iic cores should be default since they have the more interesting
features for generic use cases, i.e. SMBUS_QUICK and DMA (yet to be
supported).
Reported-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
I2C bus for VDD MPU regulator is IIC3, not I2C3.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adding the optional clock property for the mfc_pd for
handling the re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=paeu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.16-rc4" from Tony Lindgren:
Fixes for omaps for the -rc series. It's mostly fixes for clock rates,
restart handling and phy regulators and SATA interconnect data.
Also few build fixes related to the DSP driver in staging, and trivial
stuff like removal of broken and soon to be unused platform data init
for HDMI audio that would be good to get into the -rc series if not
too late.
* tag 'omap-for-v3.16/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds alias entries for UART nodes of all SoCs using
samsung-uart compatible UART controllers, so that the dependency on
probe order is removed and deterministic device naming is assured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new properties to all of the Tegra PHYs that are now required
according to the binding.
In order to stay compatible with old device trees, the USB drivers
will still function without these reset properties but with the old,
potentially buggy behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define at91sam9263ek main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the at91sam9263 clocks in the SoC dtsi file.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define at91sam9m10g45ek main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the at91sam9g45 clocks in the SoC dtsi file.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define Somfy Animeo IP main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define AK signal CDU slow crystal frequency
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define Calao TNY-A9260 and TNY-A9G20 main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define Calao USB-A9260, USB-A9G20 and USB-A9G20-LPW main and slow crystals
frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define Acme Systems srl Fox G20 main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define at91sam9g20ek main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the at91sam9g20 clocks that differ from at91sam9260 in the SoC dtsi file.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the at91sam9260 clocks in the SoC dtsi file.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define at91rm9200ek main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define Acme Systems Aria G25 board main and slow crystals frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the "atmel,nand-has-dma" property to NAND node
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As the at91sam9n12ek has switch to CCF, so add clock for wm8904
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviwed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the sama5d3xek board has switch to CCF, so add clock for wm8904
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviwed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Having clocks grouped in a subnode is common practice, so move the crystals
under a clocks node for the sama5d3 SoC and sama5d3 based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Having clocks grouped in a subnode is common practice, so move the crystals and
the ADC clock under a clocks node for the at91sam9x5 SoC and at91sam9x5 based
boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Having clocks grouped in a subnode is common practice, so move the crystals
under a clocks node for the at91sam9rl SoC and at91sam9rl based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Having clocks grouped in a subnode is common practice, so move the crystals
under a clocks node for the at91sam9n12 SoC and at91sam9n12 based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Having clocks grouped in a subnode is common practice, so move the crystals
under a clocks node for the at91sam9261 SoC and at91sam9261 based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The ldousb_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a IRQ crossbar device in the soc, which
maps the irq requests from the peripherals to the
mpu interrupt controller's inputs. The Peripheral irq
requests are connected to only one crossbar
input and the output of the crossbar is connected to only one
controller's input line. The crossbar device is used to map
a peripheral input to a free mpu's interrupt controller line.
Here, adding a new crossbar device node and replacing all the peripheral
interrupt numbers with its fixed crossbar input lines.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a IRQ crossbar device in the soc, which maps the
irq requests from the peripherals to the mpu interrupt
controller's inputs. The gic provides the support for such
IPs in the form of routable-irqs. So adding the property
here to gic node.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
