Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to make TI button interrupt working max98090 codec
Need provide mic bias all the time as long as mic is present
so SHDN and micbias pin are forced on.we also need set max98090
codec bias close or lower than TI bias.We set them in bios/coreboot
kernel reads them from device property
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some tiny improvements, cutting 180 bytes off the generated code.
- use strchr() for single-character needle
- compute index using pointer subtraction instead of two strlen()
calls
- factor out the common check for whether the initial part of
kctl->id.name (before the space) is identical to w->name.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed below error/warnings
sound/built-in.o: In function `rt5645_i2c_probe':
>> rt5645.c:(.text+0xe38f5): undefined reference to
>> `devm_regmap_init_i2c'
sound/built-in.o: In function `rt5645_i2c_driver_exit':
>> rt5645.c:(.exit.text+0x60e): undefined reference to `i2c_del_driver'
sound/built-in.o: In function `rt5645_i2c_driver_init':
>> rt5645.c:(.init.text+0x1a90): undefined reference to
>> `i2c_register_driver'
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was spotted by Fernando Lopez-Lezcano <nando@ccrma.Stanford.EDU>
while he tried to compile a -RT kernel with this driver enabled.
"make C=2" would also warn about this. This is is based on his patch.
Reported-by: Fernando Lopez-Lezcano <nando@ccrma.Stanford.EDU>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It needs free pcm runtime modules before unloading firmware, here
add hsw_pcm_suspend() to handle this procedure:
suspends firmware ==> frees runtime modules ==> unloads firmware.
This fixes the broadwell module unload failed issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add check runtime module pointers before freeing them, and clear
them to NULL after freed.
With this implemented, we can avoid NULL pointer dereference or
double free errors.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 01f202c7b4.
We shouldn't leave the device as suspended state after module freed,
it is not good to do runtime suspend at driver free, here revert
this fixing, and replace it with the procedure:
suspends firmware ==> frees runtime modules ==> unloads firmware.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 506c148ee5.
We still need this hsw_pcm_free_modules(), we plan to remove the
runtime modules at both fw_unload(D0->D3) and snd_soc_sst_haswell_pcm
module removing.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need compress offload feature for broadwell broadwell machine,
here remove the non exist dependency.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In haswell-pcm module unloading, we can't free runtime modules
directly, for they may be already freed in runtime suspend.
Here add executing suspend call to unload runtime modules, only
for status not equal to RPM_SUSPEND, to fix broadwell module
removing failed issue.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unused function hsw_pcm_free_modules() to fix the
compling warning:
sound/soc/intel/haswell/sst-haswell-pcm.c:923:13:
warning: 'sw_pcm_free_modules' defined but not used
[-Wunused-function]
static void hsw_pcm_free_modules(struct hsw_priv_data *pdata)
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mailbox size can be different for different platforms. So allow the drivers
to configure the size.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Created an ops to check if DSP busy, to avoid using platform
specific registers in common IPC.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this machines can now configure TDM settings for SSP port using
set_tdm_slot API
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this machines can configure the PCM format applied on SSP port using
the set_fmt API
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have the SSP defaults now and we need to load then in hw_params callback
of BE SSP DAI ops.
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
So right now SSP configuration is statically coded in the driver. While we
would like to keep this configuration intact for the users who are using
these defaults, we need to provide a way for users to program it.
So create a local value in driver structure which is populate with default
value for now
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current ssp configuration was not configuring the frame sync polarity
and data polarity. Some codecs do need these different so add them in ssp
configuration now
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 codec supports 4 buttons detections so enabled it
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fix following sparse warnings: (new ones prefixed by >>)
>> sound/soc/intel/boards/cht_bsw_max98090_ti.c:168:37: sparse:
>> incorrect type in argument 2 (different base types)
sound/soc/intel/boards/cht_bsw_max98090_ti.c:168:37: expected
unsigned int [unsigned] val
sound/soc/intel/boards/cht_bsw_max98090_ti.c:168:37: got
restricted snd_pcm_format_t [usertype] <noident>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 are similar codec so reuse the cht_bsw_rt5645 driver
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for two Intel Cherryview-based platforms, Cherrytrail
and Braswell. This machine driver will support max98090 codec as primary
codec. it can also support TI jack detect chip as aux device if platform
supports it.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added entry in sst driver to support max98090 codec
for intel Braswell platform.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The volume blocks have an step of 0.375dB, but TLV uses 0.01dB for
units. Only use the resolution supported, ignoring the LSB of the
volume register. This results in half the steps and 0.75dB per step,
but reports accurate levels through TLV.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds TDM slot control into dapm route. The control bits
are different between rt5645 and rt5650, so we have separate dapm
routes for each codec.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645_I2S_BCLK_MS1 (reg 0x73 [5]) is reserverd in rt5645 and rt5650.
This function is move to TDM control. We can configure it by
snd_soc_dai_set_tdm_slot's slot_width parameter.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645->btn_jack is for jack button report. So the mask should be
SND_JACK_BTN_0 | SND_JACK_BTN_1 | SND_JACK_BTN_2 | SND_JACK_BTN_3.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild robot reports a implicit declaration of function
'rt5645_irq_detection' error.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 support headset button detection. Currently, the button detection
is only implemented for rt5650 codec. The button detection configuration
register's default value is different from rt5645.
And we didn't touch the register in the driver, so we will get the wrong
value when we dump the registers. We will fix it in another patch.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
while building as a module we are getting warning about
section mismatch.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild robot reports following error/warnings
sound/soc/codecs/rt5645.c: In function 'rt5645_i2c_probe':
>> sound/soc/codecs/rt5645.c:2720:4: error: implicit declaration of
>> function 'devm_gpiod_get_index'
>> [-Werror=implicit-function-declaration]
gpiod = devm_gpiod_get_index(&i2c->dev, "rt5645", 0);
^
>> sound/soc/codecs/rt5645.c:2720:10: warning: assignment makes pointer
>> from integer without a cast
gpiod = devm_gpiod_get_index(&i2c->dev, "rt5645", 0);
^
>> sound/soc/codecs/rt5645.c:2722:4: error: implicit declaration of
>> function 'gpiod_direction_input'
>> [-Werror=implicit-function-declaration]
if (IS_ERR(gpiod) || gpiod_direction_input(gpiod)) {
^
>> sound/soc/codecs/rt5645.c:2726:5: error: implicit declaration of
>> function 'desc_to_gpio' [-Werror=implicit-function-declaration]
rt5645->pdata.hp_det_gpio = desc_to_gpio(gpiod);
^
>> sound/soc/codecs/rt5645.c:2728:7: error: implicit declaration of
>> function 'gpiod_is_active_low'
>> [-Werror=implicit-function-declaration]
= !gpiod_is_active_low(gpiod);
^
cc1: some warnings being treated as errors
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
set platform specific data for intel strago platform
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code uses wrong mask when setting RT5645_DMIC_2_DP_GPIO12 bit,
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added entry in sst driver to support rt5650 codec
for intel Braswell platform.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
we have defined SNDRV_CTL_ELEM_ID_NAME_MAXLEN as size of name array so use
this define instead of numeric value
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild robot reports following warning:
"sound/soc/intel/haswell/sst-haswell-ipc.c:2204:1-6:
WARNING: invalid free of devm_ allocated data"
As julia explains to me, the memory allocated with devm_kalloc
is freed automatically on failure of a probe function. So this
kfree should be removed otherwise the double free will be got in
error handler path.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.
Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.
This was exposed by a recent vDSO cleanup.
Fixes: e7d6eefaaa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull intel drm fixes from Dave Airlie.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
drm/i915: Workaround to avoid lite restore with HEAD==TAIL
drm/i915: cope with large i2c transfers
Pull intel iommu updates from David Woodhouse:
"This lays a little of the groundwork for upcoming Shared Virtual
Memory support — fixing some bogus #defines for capability bits and
adding the new ones, and starting to use the new wider page tables
where we can, in anticipation of actually filling in the new fields
therein.
It also allows graphics devices to be assigned to VM guests again.
This got broken in 3.17 by disallowing assignment of RMRR-afflicted
devices. Like USB, we do understand why there's an RMRR for graphics
devices — and unlike USB, it's actually sane. So we can make an
exception for graphics devices, just as we do USB controllers.
Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
persistent requests. X2APIC_OPT_OUT was added to the spec as a nasty
hack to allow broken BIOSes to forbid us from using X2APIC when they
do stupid and invasive things and would break if we did.
Someone noticed that since Windows doesn't have full IOMMU support for
DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
initialising the IOMMU on the graphics unit altogether.
This means that it would be available for use in "driver mode", where
the IOMMU registers are made available through a BAR of the graphics
device and the graphics driver can do SVM all for itself.
So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
SVM capabilities. And even the platforms which *might*, if the
planets had been aligned correctly, possibly have had SVM capability
but which in practice actually don't"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: support extended root and context entries
iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
iommu/vt-d: Allow RMRR on graphics devices too
iommu/vt-d: Print x2apic opt out info instead of printing a warning
iommu/vt-d: kill bogus ecap_niotlb_iunits()
