The kerneldoc for struct tegra_dfll_soc_data is stale. Update it to
match the current structure definition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The post divider value in the frequency table is wrong as it would lead
to the PLL producing an output rate of 960 MHz instead of the desired
480 MHz. This wasn't a problem as nothing used the table to actually
initialize the PLL rate, but the bootloader configuration was used
unaltered.
If the bootloader does not set up the PLL it will fail to come when used
under Linux. To fix this don't rely on the bootloader, but set the
correct rate in the clock driver.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the bootloader does not touch PLL_C it will stay in its reset state,
failing to lock when enabled. This leads to consumers of this clock to
fail probing. Fix this by always programming the PLL with a sane rate,
which allows it to lock, at startup.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a new Tegra210 version of the pll_register_pllre function to
allow setting the proper settings for the m and n div fields.
Additionally define PLL_RE_OUT1 on Tegra210.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: define PLLRE_OUT1 register offset]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The sor_safe clock is a fixed factor (1:17) clock derived from pll_p. It
has a gate bit in the peripheral clock registers. While the SOR is being
powered up, sor_safe can be used as the source until the SOR brick can
generate its own clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dpaux (on Tegra124 and Tegra210) and dpaux1 (on Tegra210) are fixed
factor clocks (1:17) and derived from pll_p_out0 (pll_p). They also have
a gate bit in the peripheral clock registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is of the same type as dpaux and is added to feed into the
second DPAUX block used in conjunction with SOR1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the peripheral clocks on Tegra are derived from one of the top-
level PLLs with a fixed factor. Support these clocks by implementing the
->enable() and ->disable() callbacks using the peripheral clock register
banks and the ->recalc_rate() by dividing the parent rate by the fixed
factor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Starting with Tegra124, the mipi-cal clock uses the 72 MHz clock as its
source. On Tegra114 this clock's parent was clk_m, so it is the one-off
chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Trailing blank lines are undesirable (several tools, such as git,
complain about them), so remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The peripheral clock registers are defined in static tables. These
tables never need to be modified at runtime, so they can reside in
read-only memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra210, hardware control of the SATA and XUSB pad PLLs must be
done during the UPHY enable sequence rather than the PLLE enable
sequence. Export functions to do this so that hardware control can
be enabled from the XUSB padctl driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The rst_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This flag is a no-op now. Remove usage of the flag.
Acked-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sparse reports the following warnings for structures and functions that
should be declared static:
drivers/clk/tegra/clk-tegra-super-gen4.c:70:35: warning: symbol
'tegra_super_gen_info_gen4' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra-super-gen4.c:96:35: warning: symbol
'tegra_super_gen_info_gen5' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra-super-gen4.c:174:13: warning: symbol
'tegra_super_clk_init' was not declared. Should it be static?
Fix this by making the above static.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sparse reports the following warnings for functions in clk-tegra210.c
that should be declared as static:
drivers/clk/tegra/clk-tegra210.c:460:6: warning: symbol
'tegra210_pllcx_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:485:6: warning: symbol
'_pllc_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:490:6: warning: symbol
'_pllc2_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:495:6: warning: symbol
'_pllc3_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:500:6: warning: symbol
'_plla1_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:510:6: warning: symbol
'tegra210_plla_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:562:6: warning: symbol
'tegra210_plld_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:701:6: warning: symbol
'tegra210_plld2_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:709:6: warning: symbol
'tegra210_plldp_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:722:6: warning: symbol
'tegra210_pllc4_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:731:6: warning: symbol
'tegra210_pllre_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:844:6: warning: symbol
'tegra210_pllx_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:904:6: warning: symbol
'tegra210_pllmb_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:963:6: warning: symbol
'tegra210_pllp_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:1025:6: warning: symbol
'tegra210_pllu_set_defaults' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra210.c:1215:15: warning: symbol
'tegra210_clk_adjust_vco_min' was not declared. Should it be static?
Fix this by declaring the above as static.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sparse generates the following warning for the pll_m params structure:
drivers/clk/tegra/clk-tegra210.c:1569:10: warning: Initializer entry
defined twice
drivers/clk/tegra/clk-tegra210.c:1570:10: also defined here
Fix this by correcting the index for the MISC1 register.
Fixes: b31eba5ff3f7 ("clk: tegra: Add support for Tegra210 clocks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The definition, PLLU_BASE_OVERRIDE, for the pll_u OVERRIDE bit is defined
but not used and when the OVERRIDE bit is cleared in tegra210_pll_init()
the code directly uses the bit number. Therefore, use the definition,
PLLU_BASE_OVERRIDE when clearing the OVERRIDE bit.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the pll_u is not configured by the bootloader, then on kernel boot the
following warning is seen:
clk_pll_wait_for_lock: Timed out waiting for pll pll_u_vco lock
tegra_init_from_table: Failed to enable pll_u_out1
------------[ cut here ]------------
WARNING: at drivers/clk/tegra/clk.c:269
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc4-next-20151214+ #1
Hardware name: NVIDIA Tegra210 P2371 reference board (E.1) (DT)
task: ffffffc0bc0a0000 ti: ffffffc0bc0a8000 task.ti: ffffffc0bc0a8000
PC is at tegra_init_from_table+0x140/0x164
LR is at tegra_init_from_table+0x140/0x164
pc : [<ffffffc0008fee78>] lr : [<ffffffc0008fee78>] pstate: 80000045
sp : ffffffc0bc0abd50
x29: ffffffc0bc0abd50 x28: ffffffc00090b8a8
x27: ffffffc000a06000 x26: ffffffc0bc019780
x25: ffffffc00086a708 x24: ffffffc00086a790
x23: ffffffc0006d7188 x22: ffffffc0bc010000
x21: 000000000000016e x20: ffffffc0bc00d100
x19: ffffffc000944178 x18: 0000000000000007
x17: 000000000000000e x16: 0000000000000001
x15: 0000000000000007 x14: 000000000000000e
x13: 0000000000000013 x12: 000000000000001a
x11: 000000000000004d x10: 0000000000000750
x9 : ffffffc0bc0a8000 x8 : ffffffc0bc0a07b0
x7 : 0000000000000001 x6 : 0000000002d5f0f8
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000002 x2 : ffffffc000996724
x1 : 0000000000000000 x0 : 0000000000000032
---[ end trace cbd20ae519e92ced ]---
Call trace:
[<ffffffc0008fee78>] tegra_init_from_table+0x140/0x164
[<ffffffc000900ac8>] tegra210_clock_apply_init_table+0x20/0x28
[<ffffffc0008fec40>] tegra_clocks_apply_init_table+0x18/0x24
[<ffffffc00008291c>] do_one_initcall+0x90/0x194
[<ffffffc0008cfab0>] kernel_init_freeable+0x148/0x1e8
[<ffffffc000636bb0>] kernel_init+0x10/0xdc
[<ffffffc000085cd0>] ret_from_fork+0x10/0x40
clk_pll_wait_for_lock: Timed out waiting for pll pll_u_vco lock
tegra_init_from_table: Failed to enable pll_u_out2
------------[ cut here ]------------
pll_u can be either controlled by software or hardware and this is
selected via the OVERRIDE bit in the pll_u base register. In the function
tegra210_pll_init(), the OVERRIDE bit for pll_u is cleared, which selects
hardware control of the pll. However, at the same time the pll_u clocks
are populated in the init_table for tegra210 and so software will try to
configure the pll_u if it is not already configured and hence, the above
warning is seen when the pll fails to lock. Remove the pll_u clocks from
the init_table so that software does not try to configure this pll on
boot.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock sources for Tegra210 currently incorrectly include pll_c2
and pll_c3. However, both of these should have been pll_mb as shown in
the TRM. If Tegra210 happens to be configured such that the pll_mb is the
default clock for the EMC, as configured by the bootloader, then this will
cause a system hang on boot. This is because the kernel will disable the
pll_mb when disabling unused clock as it appears to be unused when it is
not.
Also add the additional pll_p clock source for the EMC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The APB2APE clock for the audio subsystem is required for powering up the
audio power domain and accessing the various modules in this subsystem on
Tegra210 devices. Add this clock for Tegra210.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
for_each_child_of_node() performs an of_node_get() on each iteration, so
before breaking out of the loop an of_node_put() is required.
Found using Coccinelle. The semantic patch used for this is as follows:
// <smpl>
@@
expression e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PLLE SS coefficients are different between Tegra210 and Tegra114.
Add SoC generation specific versions for Tegra114 and Tegra210 and use
them in their respective ->enable() callbacks.
Signed-off-by: Mark Kuo <mkuo@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
While enabling PLLE on both Tegra114 and Tegra210, we should be clearing
PLLE_MISC_VREG_BG_CTRL_MASK and PLLE_MISC_VREG_CTRL_MASK not setting
them. This patch fixes both places where we incorrectly set instead of
cleared those bits.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Software should not disable PLLE if PLLE is already put under hardware
control.
Signed-off-by: Mark Kuo <mkuo@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The logic for calculating the input rate used when figuring out the
proper dynamic steps for pllx was incorrect. It is supposed to be
calculated using parent_rate / m but it was just using the parent rate
directly, therefore using the wrong step values.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the ->enable() callback is called with a spinlock held, we cannot
call potentially blocking functions such as clk_get_rate() or
clk_get_parent(), so use the unlocked versions instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
[rklein: Adapted from ChromeOS patch, removing pllu_enable cleanup as
it isn't present upstream]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When adding the nvenc clock, it was partially named msenc in the code.
Since the msenc clock isn't present in Tegra210 and has been replaced by
the nvenc clock, its misleading to see it present. Therefore, properly
rename it.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some register for PLLM and PLLMB were named MISC0 but according to the
TRM, they have different names. Sync up the names to make it easier to
understand which register they are really referring to.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Most PLL's don't actually have LOCK_ENABLE bits. However, most PLL's
also had that flag set, which meant that the clk code was trying to
enable locks, and inadvertantly flipping bits in other fields.
For PLLM, ensure the correct register is used for the misc_register.
PLL_MISC0 contains the EN_LCKDET bit which should be used for enabling
the lock, and PLLM_MISC1 shouldn't be used at all.
Lastly, remove some of the settings which would point to the EN_LCKDET
bits for some PLLs. There is no need to enable the locks, and that is
done as part of the set_defaults logic already.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
VI-I2C has 16 bits available for its divider. Switch the divider width
to 16 instead of 8 so correct rates can be set.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures. This also adds stricter
type checking for callers of do_div, which has uncovered a number
of bugs in existing code, and fixes up the ones we have found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4psa
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures.
This also adds stricter type checking for callers of do_div, which has
uncovered a number of bugs in existing code, and fixes up the ones we
have found"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ARM: asm/div64.h: adjust to generic codde
__div64_32(): make it overridable at compile time
__div64_const32(): abstract out the actual 128-bit cross product code
do_div(): generic optimization for constant divisor on 32-bit machines
div64.h: optimize do_div() for power-of-two constant divisors
mtd/sm_ftl.c: fix wrong do_div() usage
drm/mgag200/mgag200_mode.c: fix wrong do_div() usage
hid-sensor-hub.c: fix wrong do_div() usage
ti/fapll: fix wrong do_div() usage
ti/clkt_dpll: fix wrong do_div() usage
tegra/clk-divider: fix wrong do_div() usage
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
nouveau/nvkm/subdev/clk/gk20a.c: fix wrong do_div() usage
This fixes a bug in tegra_clk_register_pllss() which mistakenly assume
the IDDQ register is the PLL base address.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This fixes two things.
- Read the correct IDDQ register
- Check the correct IDDQ bit position
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Without this change clk_get_rate would return the final output
rather than the VCO output as it would factor in the pdiv when
it shouldn't. This will cause problems for all dividers in the
subtree of the VCO PLL.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Super clock divider control and clock source mux of Tegra210 has changed
a little against prior SoCs, this patch adds Gen5 logic to address those
differences.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add some logic for Spread Spectrum control. It is used in conjuncture
with SDM fractional dividers. SSC has to be disabled when we configure
the divider settings.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a callback to the pll_params for custom dynamic ramping
functions which can be specified per PLL.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add logic which (if specified for a pll) can verify that a PLL is set
to the proper default value and if not can set it. This can be
specified per PLL as each will have different default values.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code makes use of the SDM fractional divider if present to
constrain the allowable programming range of the PLL divider register
bitfields to take advantage of higher frequency granularity that can
be induced by the SDM divider.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 SoC's have 2 PLLs for memory usage. Add plumbing to register
and handle PLLMB.
PLLMB is used to allow switching between 2 PLLM's without having to use
and intermediate backup PLL, as we need to lock the PLL before we can
switch to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra210 SoC's, the logic to enable several of the plls is different
from previous generations. Therefore, add registration functions specific
to Tegra210 which will handle them appropriately.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLLM is fixed for Tegra30 up through Tegra114. Starting with Tegra124
PLLM can change rate. Mark PLLM as TEGRA_PLL_FIXED for the generations
where it should be. Modify the check in clk_pll_round_rate() and
clk_pll_recalc_rate() to allow for the non-fixed version to return the
correct rate.
Note that there is no change for Tegra20. This is because PLLM is not
distinguished in that driver, and adding either the PLLM or FIXED_RATE
flags will cause potential problems.
PLLM never supported dynamic ramping. On Tegra20 and Tegra30, there is
no dynamic ramping at all, and on Tegra114, Tegra124 and Tegra132, only
PLLX and PLLC support dynamic ramping, so we can go ahead and remove the
specialized pllm_ops.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This removes the conversion from pdiv to hw, which is already taken
care of by _get_table_rate before this code is run. This avoids
incorrectly converting pdiv to hw twice and getting the wrong hw value.
Also set the input_rate in the freq cfg in _calc_dynamic_ramp_rate while
setting all the other fields.
In order to prevent regressions on earlier SoC generations, all of the
frequency tables need to be updated so that they contain the actual
divider values. If they contain hardware values these would be converted
to hardware values again, yielding the wrong value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: fix regressions on earlier SoC generations]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If a PLL has a reset_reg specified, properly handle that in the
enable/disable logic paths.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra210, the logic to calculate out-of-table rates is different
from previous generations. Add callbacks that can be overridden to
allow for different ways of calculating rates. Default to
_cal_rate when not specified.
This patch also includes a new flag which is used to set which method
of fixed_mdiv calculation is used. The new method for calculating the
fixed divider value for M can be more accurate especially when
fractional dividers are in play. This allows for older chipsets to use
the existing logic and new generations to use a newer version which
may work better for them.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds logic for taking SDM_DIN (Sigma Delta Modulator) setting into
the equation to calculate the effective N value for PLL which supports
fractional divider.
The effective N = NDIV + 1/2 + SDM_DIN/2^13, where NDIV is the integer
feedback divider.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
SoC specific drivers should define the appropriate flags for each
PLL rather than relying on the registration functions to automatically
set flags on their behalf. This will properly allow for changes between
SoC generations where flags might be different and allow sharing the
same logic functions.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
New SoC's may have more than 3 MISC registers, so bump up the array size
and use a #define to be more informative about the value.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Swap out the generic WARN_ON with a WARN which gives more information
about what is happening.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of having multiple similar wrapper functions for
_clk_pll_[enable|disable], we can simplify it to single
wrappers and use checks to avoid the logic we don't want to use.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Create a wrapper interface to make use of the existing
clk_pll_wait_for_lock. This will be useful for implementations
of callbacks in Tegra SoC specific clock drivers.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has significant differences in muxes for peripheral clocks.
One of the most important changes is that pll_m isn't to be used
as a source for peripherals. Therefore, we need to define the new
muxes and new clocks to use those muxes for Tegra210 support.
Tegra210 has some differences in the PLLP clock tree:
- Four new output clocks: PLLP_OUT_CPU, PLLP_OUT_ADSP, PLLP_OUT_HSIO,
and PLLP_OUT_XUSB.
- PLLP_OUT2 is fixed at 1/2 the rate of PLLP_VCO.
- PLLP_OUT4 is the child of PLLP_OUT_CPU.
Update the xusb_hs_src mux and add the xusb_ssp_src mux for Tegra210.
Including work by Andrew Bresticker <abrestic@chromium.org> and
Bill Huang <bilhuang@nvidia.com>.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use unsigned int for loop variables that can never become negative and
remove a couple of gratuitous blank lines. Also use single spaces around
operators and use a single space instead of a tab to separate comments
from code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OSC_FREQ field of the OSC_CTRL register uses the value 12 for an
oscillator frequency of 26 MHz, not 260 MHz. This isn't really critical
because I don't think boards with such an oscillator have ever existed,
much less been supported upstream.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains a patch that allows the DFLL to use clock rates higher
than 2^31-1 Hz by using the ->determine_rate() operation instead of the
->round_rate() operation. Other than that there's a couple of cleanups
in preparation for Tegra210 support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4qKy
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.4-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.4-rc1
This contains a patch that allows the DFLL to use clock rates higher
than 2^31-1 Hz by using the ->determine_rate() operation instead of the
->round_rate() operation. Other than that there's a couple of cleanups
in preparation for Tegra210 support.
tegra_audio_clk_init was written expecting a single PLL to be
passed in directly. Change this to accept an array which will
allow for supporting multiple plls and specifying specific data
about them, like their parent, which may change over time.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Benson Leung pointed out that the kerneldoc for this structure has
become stale. Update the field descriptions to match the structure
content.
Reported-by: Benson Leung <bleung@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some fields moved from the tegra_clk_pll struct to the tegra_pll_params
struct. Update the struct comments to reflect where the fields really
are.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The monitor code is used with DEBUG_FS only, so move it into the
corresponding #ifdef block to avoid potential compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
for_each_child_of_node performs an of_node_put on each iteration, so
putting an of_node_put before a continue results in a double put.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The OPP list needs to be protected against concurrent accesses. Using
simple RCU read locks does the trick and gets rid of the following
lockdep warning:
===============================
[ INFO: suspicious RCU usage. ]
4.2.0-next-20150908 #1 Not tainted
-------------------------------
drivers/base/power/opp.c:460 Missing rcu_read_lock() or dev_opp_list_lock protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
4 locks held by kworker/u8:0/6:
#0: ("%s""deferwq"){++++.+}, at: [<c0040d8c>] process_one_work+0x118/0x4bc
#1: (deferred_probe_work){+.+.+.}, at: [<c0040d8c>] process_one_work+0x118/0x4bc
#2: (&dev->mutex){......}, at: [<c03b8194>] __device_attach+0x20/0x118
#3: (prepare_lock){+.+...}, at: [<c054bc08>] clk_prepare_lock+0x10/0xf8
stack backtrace:
CPU: 2 PID: 6 Comm: kworker/u8:0 Not tainted 4.2.0-next-20150908 #1
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: deferwq deferred_probe_work_func
[<c001802c>] (unwind_backtrace) from [<c00135a4>] (show_stack+0x10/0x14)
[<c00135a4>] (show_stack) from [<c02a8418>] (dump_stack+0x94/0xd4)
[<c02a8418>] (dump_stack) from [<c03c6f6c>] (dev_pm_opp_find_freq_ceil+0x108/0x114)
[<c03c6f6c>] (dev_pm_opp_find_freq_ceil) from [<c0551a3c>] (dfll_calculate_rate_request+0xb8/0x170)
[<c0551a3c>] (dfll_calculate_rate_request) from [<c0551b10>] (dfll_clk_round_rate+0x1c/0x2c)
[<c0551b10>] (dfll_clk_round_rate) from [<c054de2c>] (clk_calc_new_rates+0x1b8/0x228)
[<c054de2c>] (clk_calc_new_rates) from [<c054e44c>] (clk_core_set_rate_nolock+0x44/0xac)
[<c054e44c>] (clk_core_set_rate_nolock) from [<c054e4d8>] (clk_set_rate+0x24/0x34)
[<c054e4d8>] (clk_set_rate) from [<c0512460>] (tegra124_cpufreq_probe+0x120/0x230)
[<c0512460>] (tegra124_cpufreq_probe) from [<c03b9cbc>] (platform_drv_probe+0x44/0xac)
[<c03b9cbc>] (platform_drv_probe) from [<c03b84c8>] (driver_probe_device+0x218/0x304)
[<c03b84c8>] (driver_probe_device) from [<c03b69b0>] (bus_for_each_drv+0x60/0x94)
[<c03b69b0>] (bus_for_each_drv) from [<c03b8228>] (__device_attach+0xb4/0x118)
ata1: SATA link down (SStatus 0 SControl 300)
[<c03b8228>] (__device_attach) from [<c03b77c8>] (bus_probe_device+0x88/0x90)
[<c03b77c8>] (bus_probe_device) from [<c03b7be8>] (deferred_probe_work_func+0x58/0x8c)
[<c03b7be8>] (deferred_probe_work_func) from [<c0040dfc>] (process_one_work+0x188/0x4bc)
[<c0040dfc>] (process_one_work) from [<c004117c>] (worker_thread+0x4c/0x4f4)
[<c004117c>] (worker_thread) from [<c0047230>] (kthread+0xe4/0xf8)
[<c0047230>] (kthread) from [<c000f7d0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: c4fe70ada4 ("clk: tegra: Add closed loop support for the DFLL")
[vince.h@nvidia.com: Unlock rcu on error path]
Signed-off-by: Vince Hsu <vince.h@nvidia.com>
[sboyd@codeaurora.org: Dropped second hunk that nested the rcu
read lock unnecessarily]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The new determine_rate prototype allows for clock rates exceeding
2^31-1 Hz to be used. Switch the DFLL clock to use determine_rate
instead of round_rate and unlock the top rates supported by the
Tegra124.
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The latest Tegra clk pull had some problems. Fix them.
drivers/clk/tegra/clk-tegra124.c:1450:6: warning: symbol 'tegra124_clock_assert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1466:6: warning: symbol 'tegra124_clock_deassert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1476:5: warning: symbol 'tegra124_reset_assert' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1486:5: warning: symbol 'tegra124_reset_deassert' was not declared. Should it be static?
drivers/clk/tegra/clk-dfll.c:590 dfll_load_i2c_lut() warn: inconsistent indenting
drivers/clk/tegra/clk-dfll.c:1448 dfll_build_i2c_lut() warn: unsigned 'td->i2c_lut[0]' is never less than zero.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QWKO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.3-rc1
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Only include clk.h in files that are using
it. Also add in a clkdev.h include that was missing in a file
using clkdev APIs.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The DFLL clocksource was missing from the list of possible parents for
the fast CPU cluster. Add it to the list.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Save and restore this register since the LP1 restore assembly routines
fiddle with it. Otherwise the CPU would keep running on PLLX after
resume from suspend even when DFLL was the original clocksource.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic platform driver support for the fast CPU cluster DFLL
clocksource found on Tegra124 SoCs. This small driver selects the
appropriate Tegra124-specific characterization data and integration
code. It relies on the DFLL common code to do most of the work.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
[treding@nvidia.com: move setup code into ->probe()]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DVCO present in the DFLL IP block has a separate reset line,
exposed via the CAR IP block. This reset line is asserted upon SoC
reset. Unless something (such as the DFLL driver) deasserts this
line, the DVCO will not oscillate, although reads and writes to the
DFLL IP block will complete.
Thanks to Aleksandr Frid <afrid@nvidia.com> for identifying this and
saving hours of debugging time.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
[ttynkkynen: ported to tegra124 from tegra114]
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
[mikko.perttunen: ported to special reset callback]
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch allows SoC-specific CAR initialization routines to register
their own reset_assert and reset_deassert callbacks with the common Tegra
CAR code. If defined, the common code will call these callbacks when a
reset control with number >= num_periph_banks * 32 is attempted to be asserted
or deasserted respectively. Numbers greater than or equal to num_periph_banks * 32
are used to avoid clashes with low numbers that are automatically mapped to
standard CAR reset lines.
Each SoC with these special resets should specify the defined reset control
numbers in a device tree header file.
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra CVB tables encode the relationship between operating voltage
and optimal frequency as a function of the so-called speedo value.
The speedo value is written to the on-chip fuses at the factory,
which allows the voltage-frequency operating points to be calculated
on an per-chip basis.
Add utility functions to parse the Tegra-specific tables and export the
voltage-frequency pairs to the generic OPP framework for other drivers
to use.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With closed loop support, the clock rate of the DFLL can be adjusted.
The oscillator itself in the DFLL is a free-running oscillator whose
rate is directly determined the supply voltage. However, the DFLL
module contains logic to compare the DFLL output rate to a fixed
reference clock (51 MHz) and make a decision to either lower or raise
the DFLL supply voltage. The DFLL module can then autonomously change
the supply voltage by communicating with an off-chip PMIC via either I2C
or PWM signals. This driver currently supports only I2C.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add shared code to support the Tegra DFLL clocksource in open-loop
mode. This root clocksource is present on the Tegra124 SoCs. The
DFLL is the intended primary clock source for the fast CPU cluster.
This code is very closely based on a patch by Paul Walmsley from
December (http://comments.gmane.org/gmane.linux.ports.tegra/15273),
which in turn comes from the internal driver by originally created
by Aleksandr Frid <afrid@nvidia.com>.
Subsequent patches will add support for closed loop mode and drivers
for the Tegra124 fast CPU cluster DFLL devices, which rely on this
code.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HDA to codec clock is named hda2codec_2x, so use the proper name in
the clock table.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As opposed to round_rate(), determine_rate() can take rate constraints
into account when choosing the best rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra124, as we now have a proper driver for the EMC.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock has never been able to do anything.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current parent, plld_out0, does not exist. The proper name is
pll_d_out0. While at it, rename the plld_dsi clock to pll_d_dsi_out to
be more consistent with other clock names.
Fixes: b270491eb9 ("clk: tegra: Define PLLD_DSI and remove dsia(b)_mux")
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no reason why Tegra114 cannot use the same generic code to set
up the oscillator, clk_m and pll_ref clocks. The only effective change
that this causes is that the CLK_SET_PARENT_RATE flag is dropped, but
since these clocks are all fixed it is not needed anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the Tegra clock driver simplifies the clock tree somewhat by
taking advantage of the fact that clk_m runs at the same frequency as
the oscillator. While that's true on all currently supported SoCs, it
does not apply to Tegra210 anymore. On Tegra210 clk_m is typically
divided down from the oscillator frequency. To support that setup, add
a separate clock for the oscillator that both clk_m and pll_ref derive
from.
Modify the tegra_osc_clk_init() function to take an additional divider
parameter for clk_m. Existing SoCs always pass in 1, whereas Tegra210
will read the divider from a register in the clock & reset controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Fixes: 6d5b988e7d ("clk: tegra: implement a reset driver")
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ret variable is often explicitly initialized to 0, but there is no
need to do so in many cases because it will immediately be overwritten
with the return value from a function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the .dev_id entries in the devclks table were oddly indented.
Make them consistent with the rest of the table.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the clocks used for HDMI audio played through the HDA controller.
Initialize the codec clock to 48Mhz and the HDA clock to 102MHz per
the TRM.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The second to last parameter of the TEGRA_CLK_PERIPH macro denotes a
table and should therefore users should pass in NULL instead of 0.
Fixes a bunch of sparse warnings like this:
warning: Using plain integer as NULL pointer
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock initialization structure is named struct clk_init_table.
Update the kerneldoc comment to use the correct name.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Tegra132 CAR supports almost the same clocks as Tegra124 CAR. This
patch mostly deals with the small differences.
Since Tegra132 contains many of the same PLL clock sources used on
Tegra114 and Tegra124, enable them in drivers/clk/tegra/clk-pll.c when
the kernel is configured to include Tegra132 support.
This patch is based on several patches from others:
1. a patch from Peter De Schrijver:
http://lkml.iu.edu/hypermail/linux/kernel/1407.1/06094.html
2. a patch from Bill Huang ("clk: tegra: enable cclk_g at boot on
Tegra132"), and
3. a patch from Allen Martin ("clk: Enable tegra clock driver for
tegra132").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Bill Huang <bilhuang@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
tegra_clocks_apply_init_table() needs to be called after the udelay
loop has been calibrated (see commit
441f199a37 ("clk: tegra: defer
application of init table") for why that is). On existing Tegra SoCs
this was done by calling tegra_clocks_apply_init_table() from
tegra_dt_init(). To make this also work on ARM64, we need to change
this into an initcall. tegra_dt_init() is called from
customize_machine which is an arch_initcall. Therefore this should
also work on existing 32bit Tegra SoCs.
Tested on Tegra20 (ventana), Tegra30 (beaverboard), Tegra124 (jetson TK1) and
Tegra132.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[paul@pwsan.com: tweaked the commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
As previously the names of the present clock and its parent were swapped.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Set the parent of the dsi lp clocks to pll_p and the rate
to 68MHz. The default parent is clk_m and rate is 12MHz, this
is too slow to receive data from the peripheral.
Per NVidia HW engineers, the optimal rate is 70MHz, but 68MHz
will suffice.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Since the SDMMC controller registers are accessed via the APB,
the APB must be flushed before gating the SDMMC clocks to prevent
register accesses to the SDMMC controllers after their clocks are
gated.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The memory controller clock runs either at half or the same frequency as
the EMC clock.
Reviewed-By: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Don't abort clock initialization if we cannot match an entry in
tegra_clk_init_table to a valid entry in the clk array.
Also log a corresponding error message.
This was discovered when testing a patch that removed the EMC clock from
tegra124_clks but left a mention in tegra_clk_init_table.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DYPAAoJEIwa5zzehBx37egQAIiatNiLLqZnfo3rwGADRz/a
POfPovktj68aPcobyzoyhFtToMqGvi9PpysyFTIQD2HJFG+5BtiIAuqtg0875zDe
EpBWgsfugrm0YktJWAtUerj60oAmNPbKfaEm1cOOWuM2lb2mV+QkRrwSTAgsqkT7
927BzMXKKBRPOVLL0RYhoF8EXa0Eg8kCqAHP8fJrzVYkRp+UrZJDnGiUP1XmWJN+
VXQMu5SEjcPMtqT7+tfX455RfREHJfBcJ1ZN/dPF8HMWDwClQG0lyc6hifh1MxwO
8DjIZNkfZeKqgDqVyC17re7pc7p8md5HL8WXbrKpK0A9vQ5bRexbPHxcwJ1T/C2Y
465H+st5XXbuzV1gbMwjK1/ycsH0tCyffckk8Yl/2e1Fs7GgPNbAELtTdl+5vV1Y
xmDXkyo/9WlRM3LQ23IGKwW7VzN86EfWVuShssfro0fO7xDdb4OOYLdQI+4bCG+h
ytQYun1vU32OEyNik5RVNQuZaMrv2c93a3bID4owwuPHPmYOPVUQaqnRX/0E51eA
aHZYbk2GlUOV3Kq5aSS4iyLg1Yj+I9/NeH9U+A4nc+PQ5FlgGToaVSCuYuw4DqbP
AAG+sqQHbkBMvDPobQz/yd1qZbAb4eLhGy11XK1t5S65rApWI55GwNXnvbyxqt8x
wpmxJTASGxcfuZZgKXm7
=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sequence for enabling hardware control of the SATA PLL
that works both when using the SATA lane with SATA and when
using it with XUSB.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
When writing a module for testing or debugging purposes, there is no way to
get hold of clk handles. This patch solves this by exposing all valid clocks
as clkdev's for the virtual device tegra-clk-debug.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Ensure some clocks critical for system operation are always. Also enable csite
for JTAG debugging and set the tsensor and soc_therm clock frequencies for the
upcoming soctherm driver.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This adds two clocks, SATA and SATA_OOB, to the Tegra124 clock initialization
table. The clocks are needed for working SATA support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This makes the SATA PLL be controlled by hardware instead of software.
This is required for working SATA support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
vi_sensor and vi_sensor2 have a wrong hw clkid on Tegra124. Fix this by
correcting the hw clkid for Tegra124 and creating the Tegra114 vi_sensor clock
from its own data. Tegra124 was also using the wrong internal clock id.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Initialize the XUSB-related clocks with appropriate parents and rates
for both Tegra114 and Tegra124.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently the Tegra1x4 clock init code hard-codes the mux setting
for xusb_hs_src and treats it as a fixed-factor clock. It is,
however, a mux which can be parented by either xusb_ss_src/2 or
pll_u_60M. Add the fixed-factor clock xusb_ss_div2 and put an
entry in periph_clks[] for the xusb_hs_src mux.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The parent-to-index mapping for xusb_fs_src is incorrect.
Fix it by adding a mux table.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Enable hardware control of PLLE spread-spectrum, IDDQ, and enable
controls when enabling PLLE. The hardware (e.g. XUSB) using PLLE
will use these controls for power-saving optimizations.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The value written to PLLE_AUX was incorrect due to a wrong variable
being used. Without this fix SATA does not work.
Cc: stable@vger.kernel.org
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved changelog]
The Tegra124 clock driver currently provides 3 clocks that don't actually
exist; 2 for NAND and one for UART5/UARTE. Delete these.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When enabling the PLLE as its final step, clk_plle_enable() would
accidentally OR in the value previously written to the PLLE_SS_CTRL
register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add div{m,n,p}_shift() and div{m,n,p}_mask_shifted() helpers to make the
code that modifies the m-, n- and p-divider fields of PLLs shorter and
easier to read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLLE has M, N and P divider shift and width parameters that differ from
the defaults. Furthermore, when clearing the M, N and P divider fields
the corresponding masks were never shifted, thereby clearing only the
lowest bits of the register. This lead to a situation where the PLLE
programming would only work if the register hadn't been touched before.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
tegra_clk_periph_no_gate_ops is a local symbol.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Tegra124 does not have gr2d and gr3d clocks. They have been replaced by the
vic03 and gpu clocks respectively.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
When requesting a rate less than the minimum clock rate for a divider,
use the maximum divider value instead of bailing out with an error.
This matches the behavior of the generic clock divider.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
When pll_x is the parent of cclk_lp, PLLX_DIV2_BYPASS_LP determines
whether cclk_lp output is divided by 2. Set TEGRA_DIVIDER_2 so that
the clk_super driver is aware of this.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The sdmmc clocks on Tegra114 and Tegra124 are 3-bit wide muxes with
6 parents. Add support for tegra_clk_sdmmc*_8 and switch Tegra114
and Tegra124 to use these clocks instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The host1x clock on Tegra124 is a 3-bit wide mux with 6 parents.
Change thte id to tegra_clk_host1x_8 so that the correct clock gets
registered.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Set correct pll_d2_out0 divider and correct the p div values for pll_d2.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
PLLD was using the same mnp table as PLLP. Fix it to use its own
table which is different from PLLP's.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
This table had settings for 216MHz, but PLLP is (and is supposed to be)
configured at 408MHz. If that table is used and PLLP_BASE_OVRRIDE is
not set, the kernel will panic in clk_pll_recalc_rate().
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Add clocks required for accessing fuses on Tegra20.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
entirely of new platform/driver support. There are some conversions of
existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc tree
this pull request is broken into two pieces. The second piece will be
sent out after arm-soc sends you the pull request that merged in core
support for the HiSilicon 3620 platform. That same pull request from
arm-soc depends on this pull request to merge in those HiSilicon bits
without causing build failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Hh66
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
tegra_clk_periph_nodiv_ops is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The "pcie_xclk" clock is not actually a clock at all, but rather a reset
domain. Now that the custom Tegra module reset API has been removed, we
can remove the definition of any "clocks" that existed solely to support
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
The Tegra CAR module implements both a clock and reset controller. So
far, the driver exposes the clock feature via the common clock API and
the reset feature using a custom API. This patch adds an implementation
of the common reset framework API (include/linux/reset*.h). The legacy
reset implementation will be removed once all drivers have been
converted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
In case of error, the function __clk_lookup() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
clk_round_rate() can be used by drivers to determine whether or not a
frequency is supported by the clock. The current Tegra clock driver
outputs an error message and a stacktrace when the requested rate isn't
supported. That's fine for clk_set_rate(), but it's confusing when all
the driver does is query whether or not a frequency is supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The low-power DSI clocks are used during host-driven transactions on the
DSI bus. Documentation recommends that they be children of PLLP and run
at a frequency of at least 52 MHz.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock for the PWM controller is slightly different from other
peripheral clocks on Tegra30. The clock source mux field start at
bit position 28 rather than 30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two GPUs on Tegra30 and each of them uses a separate clock, so
the secondary clock needs to be initialized in order for the gr3d module
to work properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add disp1 and disp2 clocks to the clock initialization table. These
clocks are required for display and HDMI support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Hook the functions for CPU hotplug support. After the CPU is hot
unplugged, the flow controller will handle to clock gate the CPU clock.
But still need to implement an empty function to avoid warning message.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tegra124 introduces a number of new peripheral clocks. This patch adds those
to the common peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 introduces a number of a new clocks. Introduce the corresponding
the IDs for them.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 has a clock which consists of a mux and a fractional divider.
Add support for this.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has periph clocks which share the hw register. Hence locking is
required.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a common function which performs super clock initialization for
Tegra114 and beyond.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce new files for fixed and PMC clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a new file for peripheral clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure. Also PLLP and the PLLP_OUT
clocks will be initialized here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move audio clocks and PLLA initialization to a common file so it can be used by
multiple Tegra SoCs. Also a new array tegra114_clks is introduced for Tegra114
which specifies which common clocks are available on Tegra114 and what their
DT IDs are.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Add a common infra for registering clkdev. This allows decoupling clk
registration from clkdev registration.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Many clocks are common between several Tegra SoCs. Define an enum to list
them so we can move them to separate files which can be shared between
SoCs. Each SoC specific file will provide an array with the common clocks
which are present on the SoC and their DT binding ID.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move some fields related to the PLL HW description to the tegra_clk_pll_params.
This allows some PLL code to be moved to common files later.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Use pll_ref instead of pll_re_vco as the pll_e parent on Tegra114. Also
add a 12Mhz pll_ref table entry for pll_e for Tegra114. This prevents
the system from crashing at bootup because of an unsupported pll_re_vco
rate.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
VCO min clipping, dynamic ramp setup and IDDQ init can be done in the
respective PLL clk_register functions if the parent is already registered.
This is done for other some PLLs already.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This flag indicates the peripheral clock does not have a divider. It will
simplify the initialization tables and avoids some very similar code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch makes periph_clk_enb_refcnt a global array, dynamically allocated
at boottime. It simplifies the macros somewhat and allows clocks common to
several Tegra SoCs to be defined in a separate files. Also the clks array
becomes global and dynamically allocated which allows the DT registration to
be moved to a generic funcion.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch determines the register bank for clock enable/disable and reset
based on the clock ID instead of hardcoding it in the tables describing the
clocks. This results in less data to be maintained in the tables, making the
code easier to understand. The full benefit of the change will be realized once
also other clocktypes will be table based.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The PLL output frequency is multiplied during the P-divider computation,
so it needs to be divided by the P-divider again before returning.
This fixes an issue where clk_round_rate() would return the multiplied
frequency instead of the real one after the P-divider.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The power-on default parent for this clock is pll_m, which turns out to
be wrong. Previously, bootloader reparented this clock. We'll do it in
the kernel as well, so that there's one less thing that we depend on
bootloader to initialize.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Perform upwards rounding when calculating dividers for periph clks on Tegra30
and Tegra114.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
pll_m will be the parent of gr2d/gr3d if we don't do this.
And because pll_m runs at a high rate so gr2d/gr3d will be
unstable. So change the parent of them to pll_c2.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
In Tegra114, vde/gr_2d/gr_3d have 3 bits for clock source selection.
So change the clock init macro for these clocks from
"TEGRA_INIT_DATA_INT" to "TEGRA_INIT_DATA_INT8".
Besides, no one uses "TEGRA_INIT_DATA_INT" after this change, so
remove this macro.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra114 sbc1-sbc6 have more possible parent clocks than Tegra30.
So correct the parents and mux width for them.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
As the clock IDs are now specified in a header file, we can use those
definitions instead of maintaining an internal enum.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
The lock bit on PLL_U does not seem to be working correctly and
sometimes never gets set when waiting for the PLL to come up.
Remove the TEGRA_PLL_USE_LOCK flag to use a constant delay.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a CLK_SET_RATE_NO_REPARENT clock flag, which will prevent muxes
being reparented during clk_set_rate.
To avoid breaking existing platforms, all callers of clk_register_mux()
are adjusted to pass the new flag. Platform maintainers are encouraged
to remove the flag if they wish to allow mux reparenting on set_rate.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Chao Xie <xiechao.mail@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spear-devel@list.st.com
Cc: linux-tegra@vger.kernel.org
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com> [tegra]
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [sunxi]
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com> [Zynq]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
across several different platforms and architectures, fixes to existing
drivers, a MAINTAINERS file fix and improvements to the basic clock
types that allow them to be of use to more platforms than before. Only a
few fixes to the core framework are included with most all of the
changes landing in the various clock drivers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SwMB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux
Pull clock framework updates from Mike Turquette:
"The common clock framework changes for 3.11 include new clock drivers
across several different platforms and architectures, fixes to
existing drivers, a MAINTAINERS file fix and improvements to the basic
clock types that allow them to be of use to more platforms than before.
Only a few fixes to the core framework are included with most all of
the changes landing in the various clock drivers themselves."
* tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux: (55 commits)
clk: tegra: fix ifdef for tegra_periph_reset_assert inline
clk: tegra: provide tegra_periph_reset_assert alternative
clk: exynos4: Fix clock aliases for cpufreq related clocks
clk: samsung: Add MUX_FA macro to pass flag and alias
clk: add support for Rockchip gate clocks
clk: vexpress: Make the clock drivers directly available for arm64
clk: vexpress: Use full node name to identify individual clocks
clk: tegra: T114: add DFLL DVCO reset control
clk: tegra: T114: add DFLL source clocks
clk: tegra: T114: add FCPU clock shaper programming, needed by the DFLL
clk: gate: add CLK_GATE_HIWORD_MASK
clk: divider: add CLK_DIVIDER_HIWORD_MASK flag
clk: mux: add CLK_MUX_HIWORD_MASK
clk: Always notify whole subtree when reparenting
MAINTAINERS: make drivers/clk entry match subdirs
clk: honor CLK_GET_RATE_NOCACHE in clk_set_rate
clk: use clk_get_rate() for debugfs
clk: tegra: Use override bits when needed
clk: tegra: override bits for Tegra30 PLLM
clk: tegra: override bits for Tegra114 PLLM
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
