After 292fac464b ("net: ethtool: eee: Remove legacy _u32 from keee")
this function has no user any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b4ff9b51-092b-4d44-bfce-c95342a05b51@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch updates the mlxbf_gige driver to support the
"get_pause_stats()" callback, which enables display of
pause frame counters via "ethtool -I -a oob_net0".
The pause frame counters are only enabled if the "counters_en"
bit is asserted in the LLU general config register. The driver
will only report stats, and thus overwrite the default stats
state of ETHTOOL_STAT_NOT_SET, if "counters_en" is asserted.
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240305212137.3525-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel bot has discovered that if CONFIG_GPIOLIB is not set compilation
will fail.
Upon investigation the issue is that qca807x_gpio() is guarded by a
preprocessor check but then it is called under
if (IS_ENABLED(CONFIG_GPIOLIB)) in the probe call so the compiler will
error out since qca807x_gpio() has not been declared if CONFIG_GPIOLIB has
not been set.
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403031332.IGAbZzwq-lkp@intel.com/
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20240305142113.795005-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305172911.502058-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the geneve driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305172911.502058-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign netdev to gtp->dev at setup time, so, we can get rid of
gtp_dev_init() completely.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240305121524.2254533-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240305121524.2254533-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the gtp driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20240305121524.2254533-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the macsec driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240305113728.1974944-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add check for usbnet_get_endpoints() and return the error if it fails
in order to transfer the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Link: https://lore.kernel.org/r/20240305075927.261284-1-nichen@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Always run fixture setup in the grandchild process, and by default also
run the teardown in the same process. However, this change makes it
possible to run the teardown in a parent process when
_metadata->teardown_parent is set to true (e.g. in fixture setup).
Fix TEST_SIGNAL() by forwarding grandchild's signal to its parent. Fix
seccomp tests by running the test setup in the parent of the test
thread, as expected by the related test code. Fix Landlock tests by
waiting for the grandchild before processing _metadata.
Use of exit(3) in tests should be OK because the environment in which
the vfork(2) call happen is already dedicated to the running test (with
flushed stdio, setpgrp() call), see __run_test() and the call to fork(2)
just before running the setup/test/teardown. Even if the test
configures its own exit handlers, they will not be run by the parent
because it never calls exit(3), and the test function either ends with a
call to _exit(2) or a signal.
Cc: Günther Noack <gnoack@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Fixes: 0710a1a73f ("selftests/harness: Merge TEST_F_FORK() into TEST_F()")
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Reported-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240305201029.1331333-1-mic@digikod.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: some clean-up patches
Here are some clean-up patches for MPTCP:
- Patch 1 drops duplicated header inclusions.
- Patch 2 updates PM 'set_flags' interface, to make it more similar to
others.
- Patch 3 adds some error messages for the PM 'set_flags' command to
help the userspace understanding what's wrong in case of error.
- Patch 4 simplifies __lookup_addr() function from pm_netlink.c.
Except for the 3rd patch, the behaviour is not supposed to be modified.
====================
Link: https://lore.kernel.org/r/20240305-upstream-net-next-20240304-mptcp-misc-cleanup-v1-0-c436ba5e569b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the lookup_by_id parameter of __lookup_addr() is true, it's the same
as __lookup_addr_by_id(), it can be replaced by __lookup_addr_by_id()
directly. So drop this parameter, let __lookup_addr() only looks up address
on the local address list by comparing addresses in it, not address ids.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240305-upstream-net-next-20240304-mptcp-misc-cleanup-v1-4-c436ba5e569b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In addition to returning the error value, this patch also sets an error
messages with GENL_SET_ERR_MSG or NL_SET_ERR_MSG_ATTR both for pm_netlink.c
and pm_userspace.c. It will help the userspace to identify the issue.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240305-upstream-net-next-20240304-mptcp-misc-cleanup-v1-3-c436ba5e569b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The headers net/tcp.h, net/genetlink.h and uapi/linux/mptcp.h are included
in protocol.h already, no need to include them again directly. This patch
removes these duplicate header inclusions.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240305-upstream-net-next-20240304-mptcp-misc-cleanup-v1-1-c436ba5e569b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently getsockopt does not support IP_ROUTER_ALERT and
IPV6_ROUTER_ALERT, and we are unable to get the values of these two
socket options through getsockopt.
This patch adds getsockopt support for IP_ROUTER_ALERT and
IPV6_ROUTER_ALERT.
Signed-off-by: Juntong Deng <juntong.deng@outlook.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
tools: ynl: add --dbg-small-recv for easier kernel testing
When testing netlink dumps I usually hack some user space up
to constrain its user space buffer size (iproute2, ethtool or ynl).
Netlink will try to fill the messages up, so since these apps use
large buffers by default, the dumps are rarely fragmented.
I was hoping to figure out a way to create a selftest for dump
testing, but so far I have no idea how to do that in a useful
and generic way.
Until someone does that, make manual dump testing easier with YNL.
Create a special option for limiting the buffer size, so I don't
have to make the same edits each time, and maybe others will benefit,
too :)
Example:
$ ./cli.py [...] --dbg-small-recv >/dev/null
Recv: read 3712 bytes, 29 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
Recv: read 3968 bytes, 31 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
Recv: read 532 bytes, 5 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
nl_len = 20 (4) nl_flags = 0x2 nl_type = 3
Now let's make the DONE not fit in the last message:
$ ./cli.py [...] --dbg-small-recv 4499 >/dev/null
Recv: read 3712 bytes, 29 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
Recv: read 4480 bytes, 35 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
Recv: read 20 bytes, 1 messages
nl_len = 20 (4) nl_flags = 0x2 nl_type = 3
A real test would also have to check the messages are complete
and not duplicated. That part has to be done manually right now.
Note that the first message is always conservatively sized by the kernel.
Still, I think this is good enough to be useful.
v2:
- patch 2:
- move the recv_size setting up
- change the default to 0 so that cli.py doesn't have to worry
what the "unset" value is
v1: https://lore.kernel.org/all/20240301230542.116823-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Most "production" netlink clients use large buffers to
make dump efficient, which means that handling of dump
continuation in the kernel is not very well tested.
Add an option for debugging / testing handling of dumps.
It enables printing of extra netlink-level debug and
lowers the recv() buffer size in one go. When used
without any argument (--dbg-small-recv) it picks
a very small default (4000), explicit size can be set,
too (--dbg-small-recv 5000).
Example:
$ ./cli.py [...] --dbg-small-recv
Recv: read 3712 bytes, 29 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
Recv: read 3968 bytes, 31 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
Recv: read 532 bytes, 5 messages
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
[...]
nl_len = 128 (112) nl_flags = 0x0 nl_type = 19
nl_len = 20 (4) nl_flags = 0x2 nl_type = 3
(the [...] are edits to shorten the commit message).
Note that the first message of the dump is sized conservatively
by the kernel.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For manual debug, allow printing the netlink level messages
to stderr.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the size of the buffer we use for recv() configurable.
The details of the buffer sizing in netlink are somewhat
arcane, we could spend a lot of time polishing this API.
Let's just leave some hopefully helpful comments for now.
This is a for-developers-only feature, anyway.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the new line even if message has no error or extack,
which leads to print(nl_msg) ending with two new lines.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
tools: ynl: clean up make clean
First change renames the clean target which removes build results,
to a more common name. Second one add missing .PHONY targets.
Third one ensures that clean deletes __pycache__.
v2: add patch 2
v1: https://lore.kernel.org/all/20240301235609.147572-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Build process uses python to generate the user space code.
Remove __pycache__ on make clean.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Donald points out most YNL makefiles are missing distclean
in .PHONY, even tho generated/Makefile does list it.
Suggested-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The make target to remove all generated files used to be called
"hardclean" because it deleted files which were tracked by git.
We no longer track generated user space files, so use the more
common "distclean" name.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-04 (ice)
This series contains updates to ice driver only.
Jake changes the driver to use relative VSI index for VF VSIs as the VF
driver has no direct use of the VSI number on ice hardware. He also
reworks some Tx/Rx functions to clarify their uses, cleans up some style
issues, and utilizes kernel helper functions.
Maciej removes a redundant call to disable Tx queues on ifdown and
removes some unnecessary devm usages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Söderlund says:
====================
ravb: Align Rx descriptor setup and maintenance
When RZ/G2L support was added the Rx code path was split in two, one to
support R-Car and one to support RZ/G2L. One reason for this is that
R-Car uses the extended Rx descriptor format, while RZ/G2L uses the
normal descriptor format.
In many aspects this is not needed as the extended descriptor format is
just a normal descriptor with extra metadata (timestamsp) appended. And
the R-Car SoCs can also use normal descriptors if hardware timestamps
were not desired. This split has led to RZ/G2L gaining support for
split descriptors in the Rx path while R-Car still lacks this.
This series is the first step in trying to merge the R-Car and RZ/G2L Rx
paths so features and bugs corrected in one will benefit the other.
The first patch in the series clarifies that the driver now supports
either normal or extended descriptors, not both at the same time by
grouping them in a union. This is the foundation that later patches will
build on the aligning the two Rx paths.
Patches 2-5 deals with correcting small issues in the Rx frame and
descriptor sizes that either were incorrect at the time they were added
in 2017 (my bad) or concepts built on-top of this initial incorrect
design.
While finally patch 6 merges the R-Car and RZ/G2L for Rx descriptor
setup and maintenance.
When this work has landed I plan to follow up with more work aligning
the rest of the Rx code paths and hopefully bring split descriptor
support to the R-Car SoCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car and RZ/G2L Rx code paths were split in two separate
implementations when support for RZ/G2L was added due to the fact that
R-Car uses the extended descriptor format while RZ/G2L uses normal
descriptors. This has led to a duplication of Rx logic with the only
difference being the different Rx descriptors types used. The
implementation however neglects to take into account that extended
descriptors are normal descriptors with additional metadata at the end
to carry hardware timestamp information.
The hardware timestamp information is only consumed in the R-Car Rx
loop and all the maintenance code around the Rx ring can be shared
between the two implementations if the difference in descriptor length
is carefully considered.
This change merges the two implementations for Rx ring maintenance by
adding a method to access both types of descriptors as normal
descriptors, as this part covers all the fields needed for Rx ring
maintenance the only difference between using normal or extended
descriptor is the size of the memory region to allocate/free and the
step size between each descriptor in the ring.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make it possible to merge the R-Car and RZ/G2L code paths move the
maximum usable size of a single Rx descriptor data slice into the
hardware information instead of using two different defines in the two
different code paths.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the define describing the RZ/G2L maximum frame size and only use
the information in the hardware information struct. This will make it
easier to merge the R-Car and RZ/G2L code paths.
There is no functional change as both the define and the maximum frame
length in the hardware information is set to 8K.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EtherAVB device requires the SKB data to be aligned to 128 bytes.
The alignment is done by allocating an skb 128 bytes larger than the
maximum frame size supported by the device and adjusting the headroom to
fit the requirement.
This code has been refactored a few times and small issues have been
added along the way. The issues are not harmful but prevent merging
parts of the Rx code which have been split in two implementations with
the addition of RZ/G2L support, a device that supports larger frame
sizes.
This change removes the need for duplicated and somewhat inaccurate
hardware alignment constrains stored in the hardware information struct
by creating a helper to handle the allocation of an skb and alignment of
an skb data.
For the R-Car class of devices the maximum frame size is 4K and each
descriptor is limited to 2K of data. The current implementation does not
support split descriptors, this limits the frame size to 2K. The
current hardware information however records the descriptor size just
under 2K due to bad understanding of the device when larger MTUs where
added.
For the RZ/G2L device the maximum frame size is 8K and each descriptor
is limited to 4K of data. The current hardware information records this
correctly, but it gets the alignment constrains wrong as just aligns it
by 128, it does not extend it by 128 bytes to allow the full frame to be
stored. This works because the RZ/G2L device supports split descriptors
and allocates each skb to 8K and aligns each 4K descriptor in this
space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct member rx_max_buf_size was added before split descriptor
support was added. It is unclear if the value describes the full skb
frame buffer or the data descriptor buffer which can be combined into a
single skb.
Rename it to make it clear it referees to the maximum frame size and can
cover multiple descriptors.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx ring can either be made up of normal or extended descriptors, not
a mix of the two at the same time. Make this explicit by grouping the
two variables in a rx_ring union.
The extension of the storage for more than one queue of normal
descriptors from a single to NUM_RX_QUEUE queues have no practical
effect. But aids in making the code readable as the code that uses it
already piggyback on other members of struct ravb_private that are
arrays of max length NUM_RX_QUEUE, e.g. rx_desc_dma. This will also make
further refactoring easier.
While at it, rename the normal descriptor Rx ring to make it clear it's
not strictly related to the GbEthernet E-MAC IP found in RZ/G2L, normal
descriptors could be used on R-Car SoCs too.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Tony Nguyen <anthony.l.nguyen@intel.com>
To: davem@davemloft.net, kuba@kernel.org, pabeni@redhat.com,
edumazet@google.com, netdev@vger.kernel.org
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>, alan.brady@intel.com
Tony Nguyen says:
====================
idpf: refactor virtchnl messages
Alan Brady says:
The motivation for this series has two primary goals. We want to enable
support of multiple simultaneous messages and make the channel more
robust. The way it works right now, the driver can only send and receive
a single message at a time and if something goes really wrong, it can
lead to data corruption and strange bugs.
To start the series, we introduce an idpf_virtchnl.h file. This reduces
the burden on idpf.h which is overloaded with struct and function
declarations.
The conversion works by conceptualizing a send and receive as a
"virtchnl transaction" (idpf_vc_xn) and introducing a "transaction
manager" (idpf_vc_xn_manager). The vcxn_mngr will init a ring of
transactions from which the driver will pop from a bitmap of free
transactions to track in-flight messages. Instead of needing to handle a
complicated send/recv for every a message, the driver now just needs to
fill out a xn_params struct and hand it over to idpf_vc_xn_exec which
will take care of all the messy bits. Once a message is sent and
receives a reply, we leverage the completion API to signal the received
buffer is ready to be used (assuming success, or an error code
otherwise).
At a low-level, this implements the "sw cookie" field of the virtchnl
message descriptor to enable this. We have 16 bits we can put whatever
we want and the recipient is required to apply the same cookie to the
reply for that message. We use the first 8 bits as an index into the
array of transactions to enable fast lookups and we use the second 8
bits as a salt to make sure each cookie is unique for that message. As
transactions are received in arbitrary order, it's possible to reuse a
transaction index and the salt guards against index conflicts to make
certain the lookup is correct. As a primitive example, say index 1 is
used with salt 1. The message times out without receiving a reply so
index 1 is renewed to be ready for a new transaction, we report the
timeout, and send the message again. Since index 1 is free to be used
again now, index 1 is again sent but now salt is 2. This time we do get
a reply, however it could be that the reply is _actually_ for the
previous send index 1 with salt 1. Without the salt we would have no
way of knowing for sure if it's the correct reply, but with we will know
for certain.
Through this conversion we also get several other benefits. We can now
more appropriately handle asynchronously sent messages by providing
space for a callback to be defined. This notably allows us to handle MAC
filter failures better; previously we could potentially have stale,
failed filters in our list, which shouldn't really have a major impact
but is obviously not correct. I also managed to remove fairly
significant more lines than I added which is a win in my book.
Additionally, this converts some variables to use auto-variables where
appropriate. This makes the alloc paths much cleaner and less prone to
memory leaks. We also fix a few virtchnl related bugs while we're here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
netlink: handle EMSGSIZE errors in the core
Ido discovered some time back that we usually force NLMSG_DONE
to be delivered in a separate recv() syscall, even if it would
fit into the same skb as data messages. He made nexthop try
to fit DONE with data in commit 8743aeff5b ("nexthop: Fix
infinite nexthop bucket dump when using maximum nexthop ID"),
and nobody has complained so far.
We have since also tried to follow the same pattern in new
genetlink families, but explaining to people, or even remembering
the correct handling ourselves is tedious.
Let the netlink socket layer consume -EMSGSIZE errors.
Practically speaking most families use this error code
as "dump needs more space", anyway.
v2:
- init err to 0 in last patch
v1: https://lore.kernel.org/all/20240301012845.2951053-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure ctrl_fill_info() returns sensible error codes and
propagate them out to netlink core. Let netlink core decide
when to return skb->len and when to treat the exit as an
error. Netlink core does better job at it, if we always
return skb->len the core doesn't know when we're done
dumping and NLMSG_DONE ends up in a separate read().
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous change added -EMSGSIZE handling to af_netlink, we don't
have to hide these errors any longer.
Theoretically the error handling changes from:
if (err == -EMSGSIZE)
to
if (err == -EMSGSIZE && skb->len)
everywhere, but in practice it doesn't matter.
All messages fit into NLMSG_GOODSIZE, so overflow of an empty
skb cannot happen.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric points out that our current suggested way of handling
EMSGSIZE errors ((err == -EMSGSIZE) ? skb->len : err) will
break if we didn't fit even a single object into the buffer
provided by the user. This should not happen for well behaved
applications, but we can fix that, and free netlink families
from dealing with that completely by moving error handling
into the core.
Let's assume from now on that all EMSGSIZE errors in dumps are
because we run out of skb space. Families can now propagate
the error nla_put_*() etc generated and not worry about any
return value magic. If some family really wants to send EMSGSIZE
to user space, assuming it generates the same error on the next
dump iteration the skb->len should be 0, and user space should
still see the EMSGSIZE.
This should simplify families and prevent mistakes in return
values which lead to DONE being forced into a separate recv()
call as discovered by Ido some time ago.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
selftest harness uses various exit codes to signal test
results. Avoid calling exit() directly, otherwise tests
may get broken by harness refactoring (like the commit
under Fixes). SKIP() will instruct the harness that the
test shouldn't run, it used to not be the case, but that
has been fixed. So just return, no need to exit.
Note that for hmm-tests this actually changes the result
from pass to skip. Which seems fair, the test is skipped,
after all.
Reported-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/all/05f7bf89-04a5-4b65-bf59-c19456aeb1f0@sirena.org.uk
Fixes: a724707976 ("selftests: kselftest_harness: use KSFT_* exit codes")
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240304233621.646054-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksij Rempel says:
====================
net: ethernet: Rework EEE
with Andrew's permission I'll continue mainlining this patches:
==============================================================
Most MAC drivers get EEE wrong. The API to the PHY is not very
obvious, which is probably why. Rework the API, pushing most of the
EEE handling into phylib core, leaving the MAC drivers to just
enable/disable support for EEE in there change_link call back.
MAC drivers are now expect to indicate to phylib if they support
EEE. This will allow future patches to configure the PHY to advertise
no EEE link modes when EEE is not supported. The information could
also be used to enable SmartEEE if the PHY supports it.
With these changes, the uAPI configuration eee_enable becomes a global
on/off. tx-lpi must also be enabled before EEE is enabled. This fits
the discussion here:
https://lore.kernel.org/netdev/af880ce8-a7b8-138e-1ab9-8c89e662eecf@gmail.com/T/
This patchset puts in place all the infrastructure, and converts one
MAC driver to the new API. Following patchsets will convert other MAC
drivers, extend support into phylink, and when all MAC drivers are
converted to the new scheme, clean up some unneeded code.
====================
Link: https://lore.kernel.org/r/20240302195306.3207716-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enabling/disabling of EEE in the MAC should happen as a result of
auto negotiation. So move the enable/disable into
fec_enet_adjust_link() which gets called by phylib when there is a
change in link status.
fec_enet_set_eee() now just stores away the LPI timer value.
Everything else is passed to phylib, so it can correctly setup the
PHY.
fec_enet_get_eee() relies on phylib doing most of the work,
the MAC driver just adds the LPI timer value.
Call phy_support_eee() if the quirk is present to indicate the MAC
actually supports EEE.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> (On iMX8MP debix)
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240302195306.3207716-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FEC is about to get its EEE code re-written. To allow this, move
fec_enet_eee_mode_set() before fec_enet_adjust_link() which will
need to call it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240302195306.3207716-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order for EEE to operate, both the MAC and the PHY need to support
it, similar to how pause works. With some exception - a number of PHYs
have SmartEEE or AutoGrEEEn support in order to provide some EEE-like
power savings with non-EEE capable MACs.
Copy the pause concept and add the call phy_support_eee() which the MAC
makes after connecting the PHY to indicate it supports EEE. phylib will
then advertise EEE when auto-neg is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MAC driver changes its EEE hardware configuration in its
adjust_link callback. This is called when auto-neg
completes. Disabling EEE via eee_enabled false will trigger an
autoneg, and as a result the adjust_link callback will be called with
phydev->enable_tx_lpi set to false. Similarly, eee_enabled set to true
and with a change of advertised link modes will result in a new
autoneg, and a call the adjust_link call.
If set_eee is called with only a change to tx_lpi_enabled which does
not trigger an auto-neg, it is necessary to call the adjust_link
callback so that the MAC is reconfigured to take this change into
account.
When setting phydev->enable_tx_lpi, take both eee_enabled and
tx_lpi_enabled into account, so the MAC drivers just needs to act on
phydev->enable_tx_lpi and not the whole EEE configuration.
The same check should be done for tx_lpi_timer too.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240302195306.3207716-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Have phylib keep track of the EEE configuration. This simplifies the
MAC drivers, in that they don't need to store it.
Future patches to phylib will also make use of this information to
further simplify the MAC drivers.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAC drivers which support EEE need to know the results of the EEE
auto-neg in order to program the hardware to perform EEE or not. The
oddly named phy_init_eee() can be used to determine this, it returns 0
if EEE should be used, or a negative error code,
e.g. -EOPPROTONOTSUPPORT if the PHY does not support EEE or negotiate
resulted in it not being used.
However, many MAC drivers get this wrong. Add phydev->enable_tx_lpi
which indicates the result of the autoneg for EEE, including if EEE is
administratively disabled with ethtool. The MAC driver can then access
this in the same way as link speed and duplex in the adjust link
callback. If enable_tx_lpi is true, the MAC should send low power
indications and does not need to consider anything else with respect
to EEE.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add helpers that phylib and phylink can use to manage EEE configuration
and determine whether the MAC should be permitted to use LPI based on
that configuration.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function is used with the set_eee() ethtool operation. Certain
fields of struct ethtool_keee() are relevant only for the get_eee()
operation. In addition, in case of the ioctl interface, we have no
guarantee that userspace sends sane values in struct ethtool_eee.
Therefore explicitly ignore all fields not needed for set_eee().
This protects from drivers trying to use unchecked and unreliable
data, relying on specific userspace behavior.
Note: Such unsafe driver behavior has been found and fixed in the
tg3 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ad7ee11e-eb7a-4975-9122-547e13a161d8@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
