Some computations in intel_pstate_get_min_max() are not necessary
and one of its two callers doesn't even use the full result.
First off, the fixed-point value of cpu->max_perf represents a
non-negative number between 0 and 1 inclusive and cpu->min_perf
cannot be greater than cpu->max_perf. It is not necessary to check
those conditions every time the numbers in question are used.
Moreover, since intel_pstate_max_within_limits() only needs the
upper boundary, it doesn't make sense to compute the lower one in
there and returning min and max from intel_pstate_get_min_max()
via pointers doesn't look particularly nice.
For the above reasons, drop intel_pstate_get_min_max(), add a helper
to get the base P-state for min/max computations and carry out them
directly in the previous callers of intel_pstate_get_min_max().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
intel_pstate_hwp_set() is the only function walking policy->cpus
in intel_pstate. The rest of the code simply assumes one CPU per
policy, including the initialization code.
Therefore it doesn't make sense for intel_pstate_hwp_set() to
walk policy->cpus as it is guaranteed to have only one bit set
for policy->cpu.
For this reason, rearrange intel_pstate_hwp_set() to take the CPU
number as the argument and drop the loop over policy->cpus from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a new function pid_in_use() to return the information on whether
or not the PID-based P-state selection algorithm is in use.
That allows a couple of complicated conditions in the code to be
reduced to simple checks against the new function's return value.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpu_defaults structure is redundant, because it only contains
one member of type struct pstate_funcs which can be used directly
instead of struct cpu_defaults.
For this reason, drop struct cpu_defaults, use struct pstate_funcs
directly instead of it where applicable and rename all of the
variables of that type accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move the definitions of the cpu_defaults structures after the
definitions of utilization update callback routines to avoid
extra declarations of the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid using extra function pointers during P-state selection by
dropping the get_target_pstate member from struct pstate_funcs,
adding a new update_util callback to it (to be registered with
the CPU scheduler as the utilization update callback in the active
mode) and reworking the utilization update callback routines to
invoke specific P-state selection functions directly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that some overhead in the utilization update callbacks
registered by intel_pstate in the active mode can be avoided if
those callbacks are tailored to specific configurations of the
driver. For example, the utilization update callback for the HWP
enabled case only needs to update the average CPU performance
periodically whereas the utilization update callback for the
PID-based algorithm does not need to take IO-wait boosting into
account and so on.
With that in mind, define three utilization update callbacks for
three different use cases: HWP enabled, the CPU load "powersave"
P-state selection algorithm and the PID-based "powersave" P-state
selection algorithm and modify the driver initialization to
choose the callback matching its current configuration.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
One of the checks in intel_pstate_update_status() implicitly relies
on the information that there are only two struct cpufreq_driver
objects available, but it is better to do it directly against the
value it really is about (to make the code easier to follow if
nothing else).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The driver_registered variable in intel_pstate is used for checking
whether or not the driver has been registered, but intel_pstate_driver
can be used for that too (with the rule that the driver is not
registered as long as it is NULL).
That is a bit more straightforward and the code may be simplified
a bit this way, so modify the driver accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PID controller parameters only need to be initialized if the
get_target_pstate_use_performance() P-state selection routine
is going to be used. It is not necessary to initialize them
otherwise, so don't do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the HWP enabled case pid_params.sample_rate_ns only needs to be
updated once, because it is global, so do that when setting hwp_active
instead of doing it during the initialization of every CPU.
Moreover, pid_params.sample_rate_ms is never used if HWP is enabled,
so do not update it at all then.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
intel_pstate_busy_pid_reset() is the only caller of pid_reset(),
pid_p_gain_set(), pid_i_gain_set(), and pid_d_gain_set(). Moreover,
it passes constants as two parameters of pid_reset() and all of
the other routines above essentially contain the same code, so
fold all of them into the caller and drop unnecessary computations.
Introduce percent_fp() for converting integer values in percent
to fixed-point fractions and use it in the above code cleanup.
Finally, rename intel_pstate_busy_pid_reset() to
intel_pstate_pid_reset() as it also is used for the
initialization of PID parameters for every CPU and the
meaning of the "busy" part of the name is not particularly
clear.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is only one caller of intel_pstate_reset_all_pid(), which is
pid_param_set() used in the debugfs interface only, and having that
code split does not make it particularly convenient to follow.
For this reason, move the body of intel_pstate_reset_all_pid() into
its caller and drop that function.
Also change the loop from for_each_online_cpu() (which is obviously
racy with respect to CPU offline/online) to for_each_possible_cpu(),
so that all PID parameters are reset for all CPUs regardless of their
online/offline status (to prevent, for example, a previously offline
CPU from going online with a stale set of PID parameters).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that both the existing struct cpu_defaults instances in which
PID parameters are actually initialized use the same values of those
parameters, so it is not really necessary to copy them over to
pid_params dynamically.
Instead, initialize pid_params statically with those values and
drop the unused pid_policy member from struct cpu_defaults along
with copy_pid_params() used for initializing it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The P-state selection algorithm used by intel_pstate for Atom
processors is not based on the PID controller and the initialization
of PID parametrs for those processors is pointless and confusing, so
drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After recent changes the purpose of struct perf_limits is not
particularly clear any more and the code may be made somewhat
easier to follow by eliminating it, so go for that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Both intel_pstate_verify_policy() and intel_cpufreq_verify_policy()
set policy->cpuinfo.max_freq depending on the turbo status, but the
updates made by them are discarded by the core, because the policy
object passed to them by the core is temporary and cpuinfo.max_freq
from that object is not copied to the final policy object in
cpufreq_set_policy().
However, cpufreq_set_policy() passes the temporary policy object
to the ->setpolicy callback of the driver, so intel_pstate_set_policy()
actually sees the policy->cpuinfo.max_freq value updated by
intel_pstate_verify_policy() and not the final one. It also
updates policy->max sometimes which basically has no effect after
it returns, because the core discards that update.
To avoid confusion, eliminate policy->cpuinfo.max_freq updates from
intel_pstate_verify_policy() and intel_cpufreq_verify_policy()
entirely and check the maximum frequency explicitly in
intel_pstate_update_perf_limits() instead of relying on the
transiently updated policy->cpuinfo.max_freq value.
Moreover, move the max->policy adjustment carried out in
intel_pstate_set_policy() to a separate function and call that
function from the ->verify driver callbacks to ensure that it will
actually be effective.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The coordination of P-state limits used by intel_pstate in the active
mode (ie. by default) is problematic, because it synchronizes all of
the limits (ie. the global ones and the per-policy ones) so as to use
one common pair of P-state limits (min and max) across all CPUs in
the system. The drawbacks of that are as follows:
- If P-states are coordinated in hardware, it is not necessary
to coordinate them in software on top of that, so in that case
all of the above activity is in vain.
- If P-states are not coordinated in hardware, then the processor
is actually capable of setting different P-states for different
CPUs and coordinating them at the software level simply doesn't
allow that capability to be utilized.
- The coordination works in such a way that setting a per-policy
limit (eg. scaling_max_freq) for one CPU causes the common
effective limit to change (and it will affect all of the other
CPUs too), but subsequent reads from the corresponding sysfs
attributes for the other CPUs will return stale values (which
is confusing).
- Reads from the global P-state limit attributes, min_perf_pct and
max_perf_pct, return the effective common values and not the last
values set through these attributes. However, the last values
set through these attributes become hard limits that cannot be
exceeded by writes to scaling_min_freq and scaling_max_freq,
respectively, and they are not exposed, so essentially users
have to remember what they are.
All of that is painful enough to warrant a change of the management
of P-state limits in the active mode.
To that end, redesign the active mode P-state limits management in
intel_pstate in accordance with the following rules:
(1) All CPUs are affected by the global limits (that is, none of
them can be requested to run faster than the global max and
none of them can be requested to run slower than the global
min).
(2) Each individual CPU is affected by its own per-policy limits
(that is, it cannot be requested to run faster than its own
per-policy max and it cannot be requested to run slower than
its own per-policy min).
(3) The global and per-policy limits can be set independently.
Also, the global maximum and minimum P-state limits will be always
expressed as percentages of the maximum supported turbo P-state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Extend the set of systems for which intel_pstate will use the
"powersave" P-state selection algorithm based on CPU load in the
active mode by systems with ACPI preferred profile set to "tablet",
"appliance PC", "desktop", or "workstation" (ie. everything with a
specified preferred profile that is not a "server").
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, some processors supporting HWP are only supported by
intel_pstate if HWP is actually going to be used and not supported
otherwise which is confusing.
Specifically, they are not supported if "intel_pstate=no_hwp" is
passed to the kernel in the command line or if the driver is started
in the passive mode ("intel_pstate=passive").
There is no real reason for that, because everything about those
processor is known anyway and the driver can work with them in all
modes, so make that happen, but use the load-based P-state selection
algorithm for the active mode "powersave" policy with them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy->cpuinfo.max_freq and policy->max updates in
intel_cpufreq_turbo_update() are excessive as they are done for no
good reason and may lead to problems in principle, so they should be
dropped. However, after dropping them intel_cpufreq_turbo_update()
becomes almost entirely pointless, because the check made by it is
made again down the road in intel_pstate_prepare_request(). The
only thing in it that still needs to be done is the call to
update_turbo_state(), so drop intel_cpufreq_turbo_update() altogether
and make its callers invoke update_turbo_state() directly instead of
it.
In addition to that, fix intel_cpufreq_verify_policy() so that it
checks global.no_turbo in addition to global.turbo_disabled when
updating policy->cpuinfo.max_freq to make it consistent with
intel_pstate_verify_policy().
Fixes: 001c76f05b (cpufreq: intel_pstate: Generic governors support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the active mode intel_pstate currently uses two sets of global
limits, each associated with one of the possible scaling_governor
settings in that mode: "powersave" or "performance".
The driver switches over from one of those sets to the other
depending on the scaling_governor setting for the last CPU whose
per-policy cpufreq interface in sysfs was last used to change
parameters exposed in there. That obviously leads to no end of
issues when the scaling_governor settings differ between CPUs.
The most recent issue was introduced by commit a240c4aa5d (cpufreq:
intel_pstate: Do not reinit performance limits in ->setpolicy)
that eliminated the reinitialization of "performance" limits in
intel_pstate_set_policy() preventing the max limit from being set
to anything below 100, among other things.
Namely, an undesirable side effect of commit a240c4aa5d is that
now, after setting scaling_governor to "performance" in the active
mode, the per-policy limits for the CPU in question go to the highest
level and stay there even when it is switched back to "powersave"
later.
As it turns out, some distributions set scaling_governor to
"performance" temporarily for all CPUs to speed-up system
initialization, so that change causes them to misbehave later.
To fix that, get rid of the performance/powersave global limits
split and use just one set of global limits for everything.
From the user's persepctive, after this modification, when
scaling_governor is switched from "performance" to "powersave"
or the other way around on one CPU, the limits settings (ie. the
global max/min_perf_pct and per-policy scaling_max/min_freq for
any CPUs) will not change. Still, switching from "performance"
to "powersave" or the other way around changes the way in which
P-states are selected and in particular "performance" causes the
driver to always request the highest P-state it is allowed to ask
for for the given CPU.
Fixes: a240c4aa5d (cpufreq: intel_pstate: Do not reinit performance limits in ->setpolicy)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, intel_pstate_update_perf_limits() first converts the
policy minimum and maximum limits into percentages of the maximum
turbo frequency (rounding up to an integer) and then converts these
percentages to fractions (by using fixed-point arithmetic to divide
them by 100).
That introduces a rounding error unnecessarily, because the fractions
can be obtained by carrying out fixed-point divisions directly on the
input numbers.
Rework the computations in intel_pstate_hwp_set() to use fractions
instead of percentages (and drop redundant local variables from
there) and modify intel_pstate_update_perf_limits() to compute the
fractions directly and percentages out of them.
While at it, introduce percent_ext_fp() for converting percentages
to fractions (with extended number of fraction bits) and use it in
the computations.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the functions intel_pstate_hwp_set(), min/max range from HWP capability
MSR along with max_perf_pct and min_perf_pct, is used to set the HWP
request MSR. In some cases this doesn't result in the correct HWP max/min
in HWP request.
For example: In the following case:
HWP capabilities from MSR 0x771
0x70a1220
Here cpufreq min/max frequencies from above MSR dump are 700MHz and 3.2GHz
respectively.
This will result in
hwp_min = 0x07
hwp_max = 0x20
To limit max frequency to 2GHz:
perf_limits->max_perf_pct = 63 (2GHz as a percent of 3.2GHz rounded up)
With the current calculation:
adj_range = max_perf_pct * range / 100;
adj_range = 63 * (32 - 7) / 100
adj_range = 15
max = hw_min + adj_range;
max = 7 + 15 = 22
This will result in HWP request of 0x160f, which will result in a
frequency cap of 2.2GHz not 2GHz.
The problem with the above calculation is that hwp_min of 7 is treated
as 0% in the range. But max_perf_pct is calculated with respect to minimum
as 0 and max as 3.2GHz or hwp_max, so adding hwp_min to it will result in
more than the desired.
Since the min_perf_pct and max_perf_pct is already a percent of max
frequency or hwp_max, this min/max HWP request value can be calculated
directly applying these percentage to hwp_max.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the debugfs interface for PID tuning to actually update
pid_params.sample_rate_ns on PID parameters updates, as changing
pid_params.sample_rate_ms via debugfs has no effect now.
Fixes: a4675fbc4a (cpufreq: intel_pstate: Replace timers with utilization update callbacks)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
intel_pstate_hwp_set_policy() is a wrapper around
intel_pstate_hwp_set(), but the only value it adds is to check
hwp_active before calling the latter and one of its two callers
has already checked hwp_active before that happens, so in that
code path the additional check is redundant and using the wrapper
is rather pointless.
For this reason, drop intel_pstate_hwp_set_policy() and make its
callers invoke intel_pstate_hwp_set() directly (after checking
hwp_active).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull s390 fixes from Martin Schwidefsky:
- four patches to get the new cputime code in shape for s390
- add the new statx system call
- a few bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up statx system call
KVM: s390: Fix guest migration for huge guests resulting in panic
s390/ipl: always use load normal for CCW-type re-IPL
s390/timex: micro optimization for tod_to_ns
s390/cputime: provide archicture specific cputime_to_nsecs
s390/cputime: reset all accounting fields on fork
s390/cputime: remove last traces of cputime_t
s390: fix in-kernel program checks
s390/crypt: fix missing unlock in ctr_paes_crypt on error path
Pull x86 fixes from Thomas Gleixner:
- a fix for the kexec/purgatory regression which was introduced in the
merge window via an innocent sparse fix. We could have reverted that
commit, but on deeper inspection it turned out that the whole
machinery is neither documented nor robust. So a proper cleanup was
done instead
- the fix for the TLB flush issue which was discovered recently
- a simple typo fix for a reboot quirk
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tlb: Fix tlb flushing when lguest clears PGE
kexec, x86/purgatory: Unbreak it and clean it up
x86/reboot/quirks: Fix typo in ASUS EeeBook X205TA reboot quirk
Pull irq fixes from Thomas Gleixner:
- a workaround for a GIC erratum
- a missing stub function for CONFIG_IRQDOMAIN=n
- fixes for a couple of type inconsistencies
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Fix incorrect type of register size
irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
irqdomain: Add empty irq_domain_check_msi_remap
irqchip/crossbar: Fix incorrect type of local variables
Fengguang reported random corruptions from various locations on x86-32
after commits d2852a2240 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79df ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.
After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.
There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush. For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.
It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e630 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.
Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf9599
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.
Fixes: c109bf9599 ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ARM updates from Marc Zyngier:
"vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with
many PCIe devices
General bug fixes:
- Gracefully handle exception generated with syndroms that
the host doesn't understand
- Properly invalidate TLBs on VHE systems"
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU reset
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYxENfAAoJEED/6hsPKofoEEkIAIWglnOGOHqf4pPv9OThKzKm
5CGINdPVEkJ56QNaYrINiQRHAzIUg8dsrhsisYmEdYGv3Mxf5WO0OebfzTrniNm4
GXIM8OuYD04MSnIomfGGBAwFZ6ptgdeD+PVkSFYHArkvWYfPm54ghjVj3AXmkicf
tRiIsPSiL/QT0vha5LBGfwsWOYavmZRfQBNA5yYUIHgO0Mp7LI24AeZOQiSM2ngx
Gl5xfzk0bayhZSBr+r/fvxqbEd0udiY7klGEvt3hrPT+JzzpoamEgCCZ6eLFZbGM
eABeQUzm7StD4Ib3WHkVU81ysOWndL0TK94BBBLIn1j+ht9FLi9iGkmTYspk9po=
=/phS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM updates from Marc Zyngier:
- vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
- I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
PCIe devices
- General bug fixes:
- Gracefully handle exception generated with syndroms that the host
doesn't understand
- Properly invalidate TLBs on VHE systems
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
reset
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: do not warn when MSR bitmap address is not backed
KVM: arm64: Increase number of user memslots to 512
KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
arm64: KVM: Survive unknown traps from guests
arm: KVM: Survive unknown traps from guests
KVM: arm/arm64: Let vcpu thread modify its own active state
KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=khtX
-----END PGP SIGNATURE-----
Merge tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull extable.h fix from Paul Gortmaker:
"Fixup for arch/score after extable.h introduction.
It seems that Guenter is the only one on the planet doing builds for
arch/score -- we don't have compile coverage for it in linux-next or
in the kbuild-bot either. Guenter couldn't even recall where he got
his toolchain, but was kind enough to share it with me so I could
validate this change and also add arch/score to my build coverage.
I sat on this a bit in case there was any other fallout in other arch
dirs, but since this still seems to be the only one, I might as well
send it on its way"
* tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
score: Fix implicit includes now failing build after extable change
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAljCENEACgkQ8vlZVpUN
gaP8lwf7BFtF52mKQcsVYxxZtRPH5dQwJCh3rohQ0WEJi5hHyZPZNz24dPHgc8Xl
GDq7v7o10dL3aeK6P51lYNcDb9xwYakCXm5sw46c5juca/VAVaxHb/kSDPSPUCNj
7n7mNSM61UhYAN10AXi9FGJo/Rdr0U5F1VfoWVYqaHYsItYLCjlSk6ob7vKxCPUd
458qaGBvK8luwQgFPQftJ20j81zXNuRe5JHjCQ2LtaRWM8kNI/wmyNSokD73BkZl
k8B7VqG4YpKp+4xgThp12GpXHrKB9kzQfmM4dZQQiGai9Ni59+iNqEcumv0Jb5MG
gY/m5Wc1Q45/5FosPXQYHzMPHrSJ3A==
=g1OD
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Change get_random_{int,log} to use the CRNG used by /dev/urandom and
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
random: convert get_random_int/long into get_random_u32/u64
random: use chacha20 for get_random_int/long
random: fix comment for unused random_min_urandom_seed
random: remove variable limit
random: remove stale urandom_init_wait
random: remove stale maybe_reseed_primary_crng
After changing from module.h to extable.h, score builds fail with:
arch/score/kernel/traps.c: In function 'do_ri':
arch/score/kernel/traps.c:248:4: error: implicit declaration of function 'user_disable_single_step'
arch/score/mm/extable.c: In function 'fixup_exception':
arch/score/mm/extable.c:32:38: error: dereferencing pointer to incomplete type
arch/score/mm/extable.c:34:24: error: dereferencing pointer to incomplete type
because extable.h doesn't drag in the same amount of headers as the
module.h did. Add in the headers which were implicitly expected.
Fixes: 90858794c9 ("module.h: remove extable.h include now users have migrated")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[PG: tweak commit log; refresh for sched header refactoring.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Here are 2 bugfixes for tty stuff for 4.11-rc2. One of them resolves
the pretty bad bug in the n_hdlc code that Alexander Popov found and
fixed and has been reported everywhere. The other just fixes a samsung
serial driver issue when DMA fails on some systems.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWMOjpg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykWqQCdGhbRifnxpafp5N7+aHpDHhptCnoAoK6S6gDY
hn2PYO9gz8oUxXmjwdqo
=hsvZ
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes frpm Greg KH:
"Here are two bugfixes for tty stuff for 4.11-rc2.
One of them resolves the pretty bad bug in the n_hdlc code that
Alexander Popov found and fixed and has been reported everywhere. The
other just fixes a samsung serial driver issue when DMA fails on some
systems.
Both have been in linux-next with no reported issues"
* tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Continue to work if DMA request fails
tty: n_hdlc: get rid of racy n_hdlc.tbuf
Here are two small build warning fixes for some staging drivers that
Arnd has found on his valiant quest to get the kernel to build properly
with no warnings. Both of these have been in linux-next this week and
resolve the reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWMOhww8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykjowCgtBkY+JCK4s3fdjD5ICDj05OSSy8AnR9qX6E9
o0cE++TYkutSjkR2L5og
=TVuW
-----END PGP SIGNATURE-----
Merge tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small build warning fixes for some staging drivers that
Arnd has found on his valiant quest to get the kernel to build
properly with no warnings.
Both of these have been in linux-next this week and resolve the
reported issues"
* tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: octeon: remove unused variable
staging/vc04_services: add CONFIG_OF dependency
Here is a number of different USB fixes for 4.11-rc2. Seems like there
were a lot of unresolved issues that people have been finding for this
subsystem, and a bunch of good security auditing happening as well from
Johan Hovold. There's the usual batch of gadget driver fixes and xhci
issues resolved as well.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWMOkLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymiCACeIL3h4bNEc6+XLiB+sfmQx4wV2MUAnRMD1gB0
GxkBXY1Iny94vhZC8x5r
=dlkm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
- Add a get_direction() function to the qcom driver.
- Fix two pin names in the uniphier driver.
-----BEGIN PGP SIGNATURE-----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=QWle
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Two smaller pin control fixes for the v4.11 series:
- Add a get_direction() function to the qcom driver
- Fix two pin names in the uniphier driver"
* tag 'pinctrl-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: change pin names of aio/xirq for LD11
pinctrl: qcom: add get_direction function
The purgatory code defines global variables which are referenced via a
symbol lookup in the kexec code (core and arch).
A recent commit addressing sparse warnings made these static and thereby
broke kexec_file.
Why did this happen? Simply because the whole machinery is undocumented and
lacks any form of forward declarations. The variable names are unspecific
and lack a prefix, so adding forward declarations creates shadow variables
in the core code. Aside of that the code relies on magic constants and
duplicate struct definitions with no way to ensure that these things stay
in sync. The section placement of the purgatory variables happened by
chance and not by design.
Unbreak kexec and cleanup the mess:
- Add proper forward declarations and document the usage
- Use common struct definition
- Use the proper common defines instead of magic constants
- Add a purgatory_ prefix to have a proper name space
- Use ARRAY_SIZE() instead of a homebrewn reimplementation
- Add proper sections to the purgatory variables [ From Mike ]
Fixes: 72042a8c7b ("x86/purgatory: Make functions and variables static")
Reported-by: Mike Galbraith <<efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Tobin C. Harding" <me@tobin.cc>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1703101315140.3681@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
jewel and later on the server side and all stable kernels, a fixup for
-rc1 CRUSH changes and two usability enhancements: osd_request_timeout
option and supported_features bus attribute.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJYwsEIAAoJEEp/3jgCEfOL34sH+wbYyT6uXQ3hlIoRt2FQNh5b
F6qmvH4jYRI+YyjJHgE7lLEv7cq/PESPej2hrw9U7GAso0KEsazOv+qpj4AcW+u1
arXYTIQQa2w9sCuj7/BrbEzDtnNOVnGyD3Ng0wAfvbxg/37xzqumkbccuWJm6GdH
Vjk31G4ZmaOOr38jeo0AkYWgs7kgfthLMFo73TgHTBBO9fkQQQL1xZH5D/Irzf8P
1ytfVyGeTl8D3szdkkOnc4eUFMwJ35wqesL+gAsQntx1/wDnGqa2IabXRs4oqr8F
oT88LXSP8w2PaFKI1FrwOuMov6ngg38tir2SMxGDIQ6TdxtK8lW37Cx3eHavqtE=
=f4Bs
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.11-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
- a fix for the recently discovered misdirected requests bug present in
jewel and later on the server side and all stable kernels
- a fixup for -rc1 CRUSH changes
- two usability enhancements: osd_request_timeout option and
supported_features bus attribute.
* tag 'ceph-for-4.11-rc2' of git://github.com/ceph/ceph-client:
libceph: osd_request_timeout option
rbd: supported_features bus attribute
libceph: don't set weight to IN when OSD is destroyed
libceph: fix crush_decode() for older maps
Pull i2c fixes from Wolfram Sang:
"Here are some driver bugfixes from I2C.
Unusual this time are the two reverts. One because I accidently picked
a patch from the list which I should have pulled from my co-maintainer
instead ("missing of_node_put"). And one which I wrongly assumed to be
an easy fix but it turned out already that it needs more iterations
("copy device properties")"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: copy device properties when using i2c_register_board_info()"
Revert "i2c: add missing of_node_put in i2c_mux_del_adapters"
i2c: exynos5: Avoid transaction timeouts due TRANSFER_DONE_AUTO not set
i2c: designware: add reset interface
i2c: meson: fix wrong variable usage in meson_i2c_put_data
i2c: copy device properties when using i2c_register_board_info()
i2c: m65xx: drop superfluous quirk structure
i2c: brcmstb: Fix START and STOP conditions
i2c: add missing of_node_put in i2c_mux_del_adapters
i2c: riic: fix restart condition
i2c: add missing of_node_put in i2c_mux_del_adapters
-----BEGIN PGP SIGNATURE-----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=nMno
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-4.11-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Intel, amd and mxsfb fixes.
These are the drm fixes I've collected for rc2. Mostly i915 GVT only
fixes, along with a single EDID fix, some mxsfb fixes and a few minor
amd fixes"
* tag 'drm-fixes-for-4.11-rc2' of git://people.freedesktop.org/~airlied/linux: (38 commits)
drm: mxsfb: Implement drm_panel handling
drm: mxsfb_crtc: Fix the framebuffer misplacement
drm: mxsfb: Fix crash when provided invalid DT bindings
drm: mxsfb: fix pixel clock polarity
drm: mxsfb: use bus_format to determine LCD bus width
drm/amdgpu: bump driver version for some new features
drm/amdgpu: validate paramaters in the gem ioctl
drm/amd/amdgpu: fix console deadlock if late init failed
drm/i915/gvt: change some gvt_err to gvt_dbg_cmd
drm/i915/gvt: protect RO and Rsvd bits of virtual vgpu configuration space
drm/i915/gvt: handle workload lifecycle properly
drm/edid: Add EDID_QUIRK_FORCE_8BPC quirk for Rotel RSX-1058
drm/i915/gvt: fix an error for F_RO flag
drm/i915/gvt: use pfn_valid for better checking
drm/i915/gvt: set SFUSE_STRAP properly for vitual monitor detection
drm/i915/gvt: fix an error for one register
drm/i915/gvt: add more registers into handlers list
drm/i915/gvt: have more registers with F_CMD_ACCESS flags set
drm/i915/gvt: add some new MMIOs to cmd_access white list
drm/i915/gvt: fix pcode mailbox write emulation of BDW
...
Merge 5-level page table prep from Kirill Shutemov:
"Here's relatively low-risk part of 5-level paging patchset. Merging it
now will make x86 5-level paging enabling in v4.12 easier.
The first patch is actually x86-specific: detect 5-level paging
support. It boils down to single define.
The rest of patchset converts Linux MMU abstraction from 4- to 5-level
paging.
Enabling of new abstraction in most cases requires adding single line
of code in arch-specific code. The rest is taken care by asm-generic/.
Changes to mm/ code are mostly mechanical: add support for new page
table level -- p4d_t -- where we deal with pud_t now.
v2:
- fix build on microblaze (Michal);
- comment for __ARCH_HAS_5LEVEL_HACK in kasan_populate_zero_shadow();
- acks from Michal"
* emailed patches from Kirill A Shutemov <kirill.shutemov@linux.intel.com>:
mm: introduce __p4d_alloc()
mm: convert generic code to 5-level paging
asm-generic: introduce <asm-generic/pgtable-nop4d.h>
arch, mm: convert all architectures to use 5level-fixup.h
asm-generic: introduce __ARCH_USE_5LEVEL_HACK
asm-generic: introduce 5level-fixup.h
x86/cpufeature: Add 5-level paging detection
Merge fixes from Andrew Morton:
"26 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
userfaultfd: remove wrong comment from userfaultfd_ctx_get()
fat: fix using uninitialized fields of fat_inode/fsinfo_inode
sh: cayman: IDE support fix
kasan: fix races in quarantine_remove_cache()
kasan: resched in quarantine_remove_cache()
mm: do not call mem_cgroup_free() from within mem_cgroup_alloc()
thp: fix another corner case of munlock() vs. THPs
rmap: fix NULL-pointer dereference on THP munlocking
mm/memblock.c: fix memblock_next_valid_pfn()
userfaultfd: selftest: vm: allow to build in vm/ directory
userfaultfd: non-cooperative: userfaultfd_remove revalidate vma in MADV_DONTNEED
userfaultfd: non-cooperative: fix fork fctx->new memleak
mm/cgroup: avoid panic when init with low memory
drivers/md/bcache/util.h: remove duplicate inclusion of blkdev.h
mm/vmstats: add thp_split_pud event for clarity
include/linux/fs.h: fix unsigned enum warning with gcc-4.2
userfaultfd: non-cooperative: release all ctx in dup_userfaultfd_complete
userfaultfd: non-cooperative: robustness check
userfaultfd: non-cooperative: rollback userfaultfd_exit
x86, mm: unify exit paths in gup_pte_range()
...
The reboot quirk for ASUS EeeBook X205TA contains a typo in
DMI_PRODUCT_NAME, improperly referring to X205TAW instead of
X205TA, which prevents the quirk from being triggered. The
model X205TAW already has a reboot quirk of its own.
This fix simply removes the inappropriate final letter W.
Fixes: 90b28ded88 ("x86/reboot/quirks: Add ASUS EeeBook X205TA reboot quirk")
Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Link: http://lkml.kernel.org/r/1489064417-7445-1-git-send-email-matjaz.hegedic@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Fix various iomap bugs
- Fix overly aggressive CoW preallocation garbage collection
- Fixes to CoW endio error handling
- Fix some incorrect geometry calculations
- Remove a potential system hang in bulkstat
- Try to allocate blocks more aggressively to reduce ENOSPC errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5WKj
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.11-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are some bug fixes for -rc2 to clean up the copy on write
handling and to remove a cause of hangs.
- Fix various iomap bugs
- Fix overly aggressive CoW preallocation garbage collection
- Fixes to CoW endio error handling
- Fix some incorrect geometry calculations
- Remove a potential system hang in bulkstat
- Try to allocate blocks more aggressively to reduce ENOSPC errors"
* tag 'xfs-4.11-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: try any AG when allocating the first btree block when reflinking
xfs: use iomap new flag for newly allocated delalloc blocks
xfs: remove kmem_zalloc_greedy
xfs: Use xfs_icluster_size_fsb() to calculate inode alignment mask
xfs: fix and streamline error handling in xfs_end_io
xfs: only reclaim unwritten COW extents periodically
iomap: invalidate page caches should be after iomap_dio_complete() in direct write
Currently when the 'power-supply' regulator is passed via device tree
it does not actually work since drm_panel_prepare()/drm_panel_enable()
are never called.
Quoting Thierry Reding: "It should really call drm_panel_prepare() and
drm_panel_enable() while switching on the display pipeline and
drm_panel_disable(), followed by drm_panel_unprepare() while switching
off the display pipeline."
So do as suggested, so that the 'power-supply' regulator can be functional.
Reported-by: Breno Lima <breno.lima@nxp.com>
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
