As small optimisation, unix_stream_connect() prefetches the client's
sk->sk_state without unix_state_lock() and checks if it's TCP_CLOSE.
Later, sk->sk_state is checked again under unix_state_lock().
Let's use READ_ONCE() for the first check and TCP_CLOSE directly for
the second check.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
unix_poll() and unix_dgram_poll() read sk->sk_state locklessly and
calls unix_writable() which also reads sk->sk_state without holding
unix_state_lock().
Let's use READ_ONCE() in unix_poll() and unix_dgram_poll() and pass
it to unix_writable().
While at it, we remove TCP_SYN_SENT check in unix_dgram_poll() as
that state does not exist for AF_UNIX socket since the code was added.
Fixes: 1586a5877d ("af_unix: do not report POLLOUT on listeners")
Fixes: 3c73419c09 ("af_unix: fix 'poll for write'/ connected DGRAM sockets")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ioctl(SIOCINQ) calls unix_inq_len() that checks sk->sk_state first
and returns -EINVAL if it's TCP_LISTEN.
Then, for SOCK_STREAM sockets, unix_inq_len() returns the number of
bytes in recvq.
However, unix_inq_len() does not hold unix_state_lock(), and the
concurrent listen() might change the state after checking sk->sk_state.
If the race occurs, 0 is returned for the listener, instead of -EINVAL,
because the length of skb with embryo is 0.
We could hold unix_state_lock() in unix_inq_len(), but it's overkill
given the result is true for pre-listen() TCP_CLOSE state.
So, let's use READ_ONCE() for sk->sk_state in unix_inq_len().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
sk->sk_state is changed under unix_state_lock(), but it's read locklessly
in many places.
This patch adds WRITE_ONCE() on the writer side.
We will add READ_ONCE() to the lockless readers in the following patches.
Fixes: 83301b5367 ("af_unix: Set TCP_ESTABLISHED for datagram sockets too")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a SOCK_DGRAM socket connect()s to another socket, the both sockets'
sk->sk_state are changed to TCP_ESTABLISHED so that we can register them
to BPF SOCKMAP.
When the socket disconnects from the peer by connect(AF_UNSPEC), the state
is set back to TCP_CLOSE.
Then, the peer's state is also set to TCP_CLOSE, but the update is done
locklessly and unconditionally.
Let's say socket A connect()ed to B, B connect()ed to C, and A disconnects
from B.
After the first two connect()s, all three sockets' sk->sk_state are
TCP_ESTABLISHED:
$ ss -xa
Netid State Recv-Q Send-Q Local Address:Port Peer Address:PortProcess
u_dgr ESTAB 0 0 @A 641 * 642
u_dgr ESTAB 0 0 @B 642 * 643
u_dgr ESTAB 0 0 @C 643 * 0
And after the disconnect, B's state is TCP_CLOSE even though it's still
connected to C and C's state is TCP_ESTABLISHED.
$ ss -xa
Netid State Recv-Q Send-Q Local Address:Port Peer Address:PortProcess
u_dgr UNCONN 0 0 @A 641 * 0
u_dgr UNCONN 0 0 @B 642 * 643
u_dgr ESTAB 0 0 @C 643 * 0
In this case, we cannot register B to SOCKMAP.
So, when a socket disconnects from the peer, we should not set TCP_CLOSE to
the peer if the peer is connected to yet another socket, and this must be
done under unix_state_lock().
Note that we use WRITE_ONCE() for sk->sk_state as there are many lockless
readers. These data-races will be fixed in the following patches.
Fixes: 83301b5367 ("af_unix: Set TCP_ESTABLISHED for datagram sockets too")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In case of region creation fail in ipc_devlink_create_region(), previously
created regions delete process starts from tainted pointer which actually
holds error code value.
Fix this bug by decreasing region index before delete.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4dcd183fbd ("net: wwan: iosm: devlink registration")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240604082500.20769-1-amishin@t-argos.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jacob Keller says:
====================
Intel Wired LAN Driver Updates 2024-05-29 (ice, igc)
This series includes fixes for the ice driver as well as a fix for the igc
driver.
Jacob fixes two issues in the ice driver with reading the NVM for providing
firmware data via devlink info. First, fix an off-by-one error when reading
the Preserved Fields Area, resolving an infinite loop triggered on some
NVMs which lack certain data in the NVM. Second, fix the reading of the NVM
Shadow RAM on newer E830 and E825-C devices which have a variable sized CSS
header rather than assuming this header is always the same fixed size as in
the E810 devices.
Larysa fixes three issues with the ice driver XDP logic that could occur if
the number of queues is changed after enabling an XDP program. First, the
af_xdp_zc_qps bitmap is removed and replaced by simpler logic to track
whether queues are in zero-copy mode. Second, the reset and .ndo_bpf flows
are distinguished to avoid potential races with a PF reset occuring
simultaneously to .ndo_bpf callback from userspace. Third, the logic for
mapping XDP queues to vectors is fixed so that XDP state is restored for
XDP queues after a reconfiguration.
Sasha fixes reporting of Energy Efficient Ethernet support via ethtool in
the igc driver.
v1: https://lore.kernel.org/r/20240530-net-2024-05-30-intel-net-fixes-v1-0-8b11c8c9bff8@intel.com
====================
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-0-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 01cf893bf0 ("net: intel: i40e/igc: Remove setting Autoneg in
EEE capabilities") removed SUPPORTED_Autoneg field but left inappropriate
ethtool_keee structure initialization. When "ethtool --show <device>"
(get_eee) invoke, the 'ethtool_keee' structure was accidentally overridden.
Remove the 'ethtool_keee' overriding and add EEE declaration as per IEEE
specification that allows reporting Energy Efficient Ethernet capabilities.
Examples:
Before fix:
ethtool --show-eee enp174s0
EEE settings for enp174s0:
EEE status: not supported
After fix:
EEE settings for enp174s0:
EEE status: disabled
Tx LPI: disabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
2500baseT/Full
Fixes: 01cf893bf0 ("net: intel: i40e/igc: Remove setting Autoneg in EEE capabilities")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-6-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ice_pf_dcb_recfg() re-maps queues to vectors with
ice_vsi_map_rings_to_vectors(), which does not restore the previous
state for XDP queues. This leads to no AF_XDP traffic after rebuild.
Map XDP queues to vectors in ice_vsi_map_rings_to_vectors().
Also, move the code around, so XDP queues are mapped independently only
through .ndo_bpf().
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-5-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
has placed ice_vsi_free_q_vectors() after ice_destroy_xdp_rings() in
the rebuild process. The behaviour of the XDP rings config functions is
context-dependent, so the change of order has led to
ice_destroy_xdp_rings() doing additional work and removing XDP prog, when
it was supposed to be preserved.
Also, dependency on the PF state reset flags creates an additional,
fortunately less common problem:
* PFR is requested e.g. by tx_timeout handler
* .ndo_bpf() is asked to delete the program, calls ice_destroy_xdp_rings(),
but reset flag is set, so rings are destroyed without deleting the
program
* ice_vsi_rebuild tries to delete non-existent XDP rings, because the
program is still on the VSI
* system crashes
With a similar race, when requested to attach a program,
ice_prepare_xdp_rings() can actually skip setting the program in the VSI
and nevertheless report success.
Instead of reverting to the old order of function calls, add an enum
argument to both ice_prepare_xdp_rings() and ice_destroy_xdp_rings() in
order to distinguish between calls from rebuild and .ndo_bpf().
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-4-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Referenced commit has introduced a bitmap to distinguish between ZC and
copy-mode AF_XDP queues, because xsk_get_pool_from_qid() does not do this
for us.
The bitmap would be especially useful when restoring previous state after
rebuild, if only it was not reallocated in the process. This leads to e.g.
xdpsock dying after changing number of queues.
Instead of preserving the bitmap during the rebuild, remove it completely
and distinguish between ZC and copy-mode queues based on the presence of
a device associated with the pool.
Fixes: e102db780e ("ice: track AF_XDP ZC enabled queues in bitmap")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-3-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice driver reads data from the Shadow RAM portion of the NVM during
initialization, including data used to identify the NVM image and device,
such as the ETRACK ID used to populate devlink dev info fw.bundle.
Currently it is using a fixed offset defined by ICE_CSS_HEADER_LENGTH to
compute the appropriate offset. This worked fine for E810 and E822 devices
which both have CSS header length of 330 words.
Other devices, including both E825-C and E830 devices have different sizes
for their CSS header. The use of a hard coded value results in the driver
reading from the wrong block in the NVM when attempting to access the
Shadow RAM copy. This results in the driver reporting the fw.bundle as 0x0
in both the devlink dev info and ethtool -i output.
The first E830 support was introduced by commit ba20ecb1d1 ("ice: Hook up
4 E830 devices by adding their IDs") and the first E825-C support was
introducted by commit f64e189442 ("ice: introduce new E825C devices
family")
The NVM actually contains the CSS header length embedded in it. Remove the
hard coded value and replace it with logic to read the length from the NVM
directly. This is more resilient against all existing and future hardware,
vs looking up the expected values from a table. It ensures the driver will
read from the appropriate place when determining the ETRACK ID value used
for populating the fw.bundle_id and for reporting in ethtool -i.
The CSS header length for both the active and inactive flash bank is stored
in the ice_bank_info structure to avoid unnecessary duplicate work when
accessing multiple words of the Shadow RAM. Both banks are read in the
unlikely event that the header length is different for the NVM in the
inactive bank, rather than being different only by the overall device
family.
Fixes: ba20ecb1d1 ("ice: Hook up 4 E830 devices by adding their IDs")
Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-2-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice_get_pfa_module_tlv() function iterates over the Type-Length-Value
structures in the Preserved Fields Area (PFA) of the NVM. This is used by
the driver to access data such as the Part Board Assembly identifier.
The function uses simple logic to iterate over the PFA. First, the pointer
to the PFA in the NVM is read. Then the total length of the PFA is read
from the first word.
A pointer to the first TLV is initialized, and a simple loop iterates over
each TLV. The pointer is moved forward through the NVM until it exceeds the
PFA area.
The logic seems sound, but it is missing a key detail. The Preserved
Fields Area length includes one additional final word. This is documented
in the device data sheet as a dummy word which contains 0xFFFF. All NVMs
have this extra word.
If the driver tries to scan for a TLV that is not in the PFA, it will read
past the size of the PFA. It reads and interprets the last dummy word of
the PFA as a TLV with type 0xFFFF. It then reads the word following the PFA
as a length.
The PFA resides within the Shadow RAM portion of the NVM, which is
relatively small. All of its offsets are within a 16-bit size. The PFA
pointer and TLV pointer are stored by the driver as 16-bit values.
In almost all cases, the word following the PFA will be such that
interpreting it as a length will result in 16-bit arithmetic overflow. Once
overflowed, the new next_tlv value is now below the maximum offset of the
PFA. Thus, the driver will continue to iterate the data as TLVs. In the
worst case, the driver hits on a sequence of reads which loop back to
reading the same offsets in an endless loop.
To fix this, we need to correct the loop iteration check to account for
this extra word at the end of the PFA. This alone is sufficient to resolve
the known cases of this issue in the field. However, it is plausible that
an NVM could be misconfigured or have corrupt data which results in the
same kind of overflow. Protect against this by using check_add_overflow
when calculating both the maximum offset of the TLVs, and when calculating
the next_tlv offset at the end of each loop iteration. This ensures that
the driver will not get stuck in an infinite loop when scanning the PFA.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-1-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZmAYPgAKCRDbK58LschI
g2XdAP9M8zYLRw4IG8DUFug7F+oqRPqgbs+Gvsf9YNl5/PSiTQEA6WKa/ObaG/W9
vre9VxhMWKgcMfzqZyztNHAiDm8R+QI=
=l7gV
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-06-05
We've added 8 non-merge commits during the last 6 day(s) which contain
a total of 9 files changed, 34 insertions(+), 35 deletions(-).
The main changes are:
1) Fix a potential use-after-free in bpf_link_free when the link uses
dealloc_deferred to free the link object but later still tests for
presence of link->ops->dealloc, from Cong Wang.
2) Fix BPF test infra to set the run context for rawtp test_run callback
where syzbot reported a crash, from Jiri Olsa.
3) Fix bpf_session_cookie BTF_ID in the special_kfunc_set list to exclude
it for the case of !CONFIG_FPROBE, also from Jiri Olsa.
4) Fix a Coverity static analysis report to not close() a link_fd of -1
in the multi-uprobe feature detector, from Andrii Nakryiko.
5) Revert support for redirect to any xsk socket bound to the same umem
as it can result in corrupted ring state which can lead to a crash when
flushing rings. A different approach will be pursued for bpf-next to
address it safely, from Magnus Karlsson.
6) Fix inet_csk_accept prototype in test_sk_storage_tracing.c which caused
BPF CI failure after the last tree fast forwarding, from Andrii Nakryiko.
7) Fix a coccicheck warning in BPF devmap that iterator variable cannot
be NULL, from Thorsten Blum.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
Revert "xsk: Document ability to redirect to any socket bound to the same umem"
Revert "xsk: Support redirect to any socket bound to the same umem"
bpf: Set run context for rawtp test_run callback
bpf: Fix a potential use-after-free in bpf_link_free()
bpf, devmap: Remove unnecessary if check in for loop
libbpf: don't close(-1) in multi-uprobe feature detector
bpf: Fix bpf_session_cookie BTF_ID in special_kfunc_set list
selftests/bpf: fix inet_csk_accept prototype in test_sk_storage_tracing.c
====================
Link: https://lore.kernel.org/r/20240605091525.22628-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On failed verification of PTP clock pin, error message prints channel
number instead of pin index after "pin", which is incorrect.
Fix error message by adding channel number to the message and printing
pin number instead of channel number.
Fixes: 6092315dfd ("ptp: introduce programmable pins.")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20240604120555.16643-1-karol.kolacinski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If one TCA_TAPRIO_ATTR_PRIOMAP attribute has been provided,
taprio_parse_mqprio_opt() must validate it, or userspace
can inject arbitrary data to the kernel, the second time
taprio_change() is called.
First call (with valid attributes) sets dev->num_tc
to a non zero value.
Second call (with arbitrary mqprio attributes)
returns early from taprio_parse_mqprio_opt()
and bad things can happen.
Fixes: a3d43c0d56 ("taprio: Add support adding an admin schedule")
Reported-by: Noam Rathaus <noamr@ssd-disclosure.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20240604181511.769870-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of flow rule creation fail in mlx5_lag_create_port_sel_table(),
instead of previously created rules, the tainted pointer is deleted
deveral times.
Fix this bug by using correct flow rules pointers.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 352899f384 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240604100552.25201-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5 core fixes 20240603
This small patchset provides two bug fixes from the team to the mlx5 core driver.
Series generated against:
commit 33700a0c9b ("net/tcp: Don't consider TCP_CLOSE in TCP_AO_ESTABLISHED")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case pci channel becomes offline the driver should not wait for PCI
reads during health dump and recovery flow. The driver has timeout for
each of these loops trying to read PCI, so it would fail anyway.
However, in case of recovery waiting till timeout may cause the pci
error_detected() callback fail to meet pci_dpc_recovered() wait timeout.
Fixes: b3bd076f75 ("net/mlx5: Report devlink health on FW fatal issues")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mainline MTK ethernet driver suffers long time from rarly but
annoying tx queue timeouts. We think that this is caused by fixed
dma sizes hardcoded for all SoCs.
We suspect this problem arises from a low level of free TX DMADs,
the TX Ring alomost full.
The transmit timeout is caused by the Tx queue not waking up. The
Tx queue stops when the free counter is less than ring->thres, and
it will wake up once the free counter is greater than ring->thres.
If the CPU is too late to wake up the Tx queues, it may cause a
transmit timeout.
Therefore, we increased the TX and RX DMADs to improve this error
situation.
Use the dma-size implementation from SDK in a per SoC manner. In
difference to SDK we have no RSS feature yet, so all RX/TX sizes
should be raised from 512 to 2048 byte except fqdma on mt7988 to
avoid the tx timeout issue.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaroslav reports Dell's OMSA Systems Management Data Engine
expects NLM_DONE in a separate recvmsg(), both for rtnl_dump_ifinfo()
and inet_dump_ifaddr(). We already added a similar fix previously in
commit 460b0d33cf ("inet: bring NLM_DONE out to a separate recv() again")
Instead of modifying all the dump handlers, and making them look
different than modern for_each_netdev_dump()-based dump handlers -
put the workaround in rtnetlink code. This will also help us move
the custom rtnl-locking from af_netlink in the future (in net-next).
Note that this change is not touching rtnl_dump_all(). rtnl_dump_all()
is different kettle of fish and a potential problem. We now mix families
in a single recvmsg(), but NLM_DONE is not coalesced.
Tested:
./cli.py --dbg-small-recv 4096 --spec netlink/specs/rt_addr.yaml \
--dump getaddr --json '{"ifa-family": 2}'
./cli.py --dbg-small-recv 4096 --spec netlink/specs/rt_route.yaml \
--dump getroute --json '{"rtm-family": 2}'
./cli.py --dbg-small-recv 4096 --spec netlink/specs/rt_link.yaml \
--dump getlink
Fixes: 3e41af9076 ("rtnetlink: use xarray iterator to implement rtnl_dump_ifinfo()")
Fixes: cdb2f80f1c ("inet: use xa_array iterator to implement inet_dump_ifaddr()")
Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Link: https://lore.kernel.org/all/CAK8fFZ7MKoFSEzMBDAOjoUt+vTZRRQgLDNXEOfdCCXSoXXKE0g@mail.gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like previous patch does in TCP, we need to adhere to RFC 1213:
"tcpCurrEstab OBJECT-TYPE
...
The number of TCP connections for which the current state
is either ESTABLISHED or CLOSE- WAIT."
So let's consider CLOSE-WAIT sockets.
The logic of counting
When we increment the counter?
a) Only if we change the state to ESTABLISHED.
When we decrement the counter?
a) if the socket leaves ESTABLISHED and will never go into CLOSE-WAIT,
say, on the client side, changing from ESTABLISHED to FIN-WAIT-1.
b) if the socket leaves CLOSE-WAIT, say, on the server side, changing
from CLOSE-WAIT to LAST-ACK.
Fixes: d9cd27b8cd ("mptcp: add CurrEstab MIB counter support")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC 1213, we should also take CLOSE-WAIT sockets into
consideration:
"tcpCurrEstab OBJECT-TYPE
...
The number of TCP connections for which the current state
is either ESTABLISHED or CLOSE- WAIT."
After this, CurrEstab counter will display the total number of
ESTABLISHED and CLOSE-WAIT sockets.
The logic of counting
When we increment the counter?
a) if we change the state to ESTABLISHED.
b) if we change the state from SYN-RECEIVED to CLOSE-WAIT.
When we decrement the counter?
a) if the socket leaves ESTABLISHED and will never go into CLOSE-WAIT,
say, on the client side, changing from ESTABLISHED to FIN-WAIT-1.
b) if the socket leaves CLOSE-WAIT, say, on the server side, changing
from CLOSE-WAIT to LAST-ACK.
Please note: there are two chances that old state of socket can be changed
to CLOSE-WAIT in tcp_fin(). One is SYN-RECV, the other is ESTABLISHED.
So we have to take care of the former case.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_redbox.sh test need to create bridge for testing. Add the missing
config CONFIG_BRIDGE in config file.
Fixes: eafbf0574e ("test: hsr: Extend the hsr_redbox.sh to have more SAN devices connected")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f58f45c1e5 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
q->bands will be assigned to qopt->bands to execute subsequent code logic
after kmalloc. So the old q->bands should not be used in kmalloc.
Otherwise, an out-of-bounds write will occur.
Fixes: c2999f7fb0 ("net: sched: multiq: don't call qdisc_put() while holding tree lock")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8061 needs to write to a MMD register at driver initialization to fix
an errata. This worked in 5.0 kernel but not in newer kernels. The
issue is the main phylib code no longer resets PHY at the very beginning.
Calling phy resuming code later will reset the chip if it is already
powered down at the beginning. This wipes out the MMD register write.
Solution is to implement a phy resume function for KSZ8061 to take care
of this problem.
Fixes: 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying smc settings to clcsock, avoid setting clcsock's sk_sndbuf
to sysctl_tcp_wmem[1], since this may overwrite the value set by
tcp_sndbuf_expand() in TCP connection establishment.
And the other setting sk_{snd|rcv}buf to sysctl value in
smc_adjust_sock_bufsizes() can also be omitted since the initialization
of smc sock and clcsock has set sk_{snd|rcv}buf to smc.sysctl_{w|r}mem
or ipv4_sysctl_tcp_{w|r}mem[1].
Fixes: 30c3c4a449 ("net/smc: Use correct buffer sizes when switching between TCP and SMC")
Link: https://lore.kernel.org/r/5eaf3858-e7fd-4db8-83e8-3d7a3e0e9ae2@linux.alibaba.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>, too.
Signed-off-by: David S. Miller <davem@davemloft.net>
PF mcam entries has to be at low priority always so that VF
can install longest prefix match rules at higher priority.
This was taken care currently but when priority allocation
wrt reference entry is requested then entries are allocated
from mid-zone instead of low priority zone. Fix this and
always allocate entries from low priority zone for PFs.
Fixes: 7df5b4b260 ("octeontx2-af: Allocate low priority entries for PF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2863d665ea.
This patch introduced a potential kernel crash when multiple napi instances
redirect to the same AF_XDP socket. By removing the queue_index check, it is
possible for multiple napi instances to access the Rx ring at the same time,
which will result in a corrupted ring state which can lead to a crash when
flushing the rings in __xsk_flush(). This can happen when the linked list of
sockets to flush gets corrupted by concurrent accesses. A quick and small fix
is not possible, so let us revert this for now.
Reported-by: Yuval El-Hanany <YuvalE@radware.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/xdp-newbies/8100DBDC-0B7C-49DB-9995-6027F6E63147@radware.com
Link: https://lore.kernel.org/bpf/20240604122927.29080-2-magnus.karlsson@gmail.com
For TLS offload we mark packets with skb->decrypted to make sure
they don't escape the host without getting encrypted first.
The crypto state lives in the socket, so it may get detached
by a call to skb_orphan(). As a safety check - the egress path
drops all packets with skb->decrypted and no "crypto-safe" socket.
The skb marking was added to sendpage only (and not sendmsg),
because tls_device injected data into the TCP stack using sendpage.
This special case was missed when sendpage got folded into sendmsg.
Fixes: c5c37af6ec ("tcp: Convert do_tcp_sendpages() to use MSG_SPLICE_PAGES")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240530232607.82686-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The first fixes for v6.10. And we have a big one, I suspect the
biggest wireless pull request we ever had. There are fixes all over,
both in stack and drivers. Likely the most important here are mt76 not
working on mt7615 devices, ath11k not being able to connect to 6 GHz
networks and rtlwifi suffering from packet loss. But of course there's
much more.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZdrSMRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuYnAgAqZMvSQKbhkYRfIua9Ygmdk8pDetEhaJg
HAUiW8ymLkWG1Md1V3tjY9Es66YeSr03Tx8xz/8pDWSaiUCdCs+u0zonhRK0sb3/
HAfyUpRIGDq/9kTM9lfL+yOTKwtRti+NmTXqeJr1CrpBejuXydRT+YYcIEmwQQxw
pm5xwLmrq74pMRE3VCTRbj2mfv/leFoDQasTeimUi6PgRrCeXSmUDy14k1zyAsI5
/uchvyvhgN54U2vIvO0RzW5zfS84cNEG+mW/+PpiuMftH2sYS1/UqT8BCQdrfzBz
PuiocUBXU68NzB4iLZhzPSDirOsYVaYpgKPfLPF1jNoj+iEQh1HhCA==
=5my7
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.10-rc3
The first fixes for v6.10. And we have a big one, I suspect the
biggest wireless pull request we ever had. There are fixes all over,
both in stack and drivers. Likely the most important here are mt76 not
working on mt7615 devices, ath11k not being able to connect to 6 GHz
networks and rtlwifi suffering from packet loss. But of course there's
much more.
* tag 'wireless-2024-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (37 commits)
wifi: rtlwifi: Ignore IEEE80211_CONF_CHANGE_RETRY_LIMITS
wifi: mt76: mt7615: add missing chanctx ops
wifi: wilc1000: document SRCU usage instead of SRCU
Revert "wifi: wilc1000: set atomic flag on kmemdup in srcu critical section"
Revert "wifi: wilc1000: convert list management to RCU"
wifi: mac80211: fix UBSAN noise in ieee80211_prep_hw_scan()
wifi: mac80211: correctly parse Spatial Reuse Parameter Set element
wifi: mac80211: fix Spatial Reuse element size check
wifi: iwlwifi: mvm: don't read past the mfuart notifcation
wifi: iwlwifi: mvm: Fix scan abort handling with HW rfkill
wifi: iwlwifi: mvm: check n_ssids before accessing the ssids
wifi: iwlwifi: mvm: properly set 6 GHz channel direct probe option
wifi: iwlwifi: mvm: handle BA session teardown in RF-kill
wifi: iwlwifi: mvm: Handle BIGTK cipher in kek_kck cmd
wifi: iwlwifi: mvm: remove stale STA link data during restart
wifi: iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
wifi: iwlwifi: mvm: set properly mac header
wifi: iwlwifi: mvm: revert gen2 TX A-MPDU size to 64
wifi: iwlwifi: mvm: d3: fix WoWLAN command version lookup
wifi: iwlwifi: mvm: fix a crash on 7265
...
====================
Link: https://lore.kernel.org/r/20240603115129.9494CC2BD10@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in lib/test_rhashtable.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240531-md-lib-test_rhashtable-v1-1-cd6d4138f1b6@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
dst_cache: fix possible races
This series is inspired by various undisclosed syzbot
reports hinting at corruptions in dst_cache structures.
It seems at least four users of dst_cache are racy against
BH reentrancy.
Last patch is adding a DEBUG_NET check to catch future misuses.
====================
Link: https://lore.kernel.org/r/20240531132636.2637995-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After fixing four different bugs involving dst_cache
users, it might be worth adding a check about BH being
blocked by dst_cache callers.
DEBUG_NET_WARN_ON_ONCE(!in_softirq());
It is not fatal, if we missed valid case where no
BH deadlock is to be feared, we might change this.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
ila_output() is called from lwtunnel_output()
possibly from process context, and under rcu_read_lock().
We might be interrupted by a softirq, re-enter ila_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in seg6_output_core() is not good enough,
because seg6_output_core() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter seg6_output_core()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in seg6_input_core().
Fixes: fa79581ea6 ("ipv6: sr: fix several BUGs when preemption is enabled")
Fixes: 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <dlebrun@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in rpl_output() is not good enough,
because rpl_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter rpl_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in rpl_input().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <aahringo@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in ioam6_output() is not good enough,
because ioam6_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter ioam6_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Fixes: 8cb3bf8bff ("ipv6: ioam: Add support for the ip6ip6 encapsulation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Justin Iurman <justin.iurman@uliege.be>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 1a80dbcb2d, bpf_link can be freed by
link->ops->dealloc_deferred, but the code still tests and uses
link->ops->dealloc afterward, which leads to a use-after-free as
reported by syzbot. Actually, one of them should be sufficient, so
just call one of them instead of both. Also add a WARN_ON() in case
of any problematic implementation.
Fixes: 1a80dbcb2d ("bpf: support deferring bpf_link dealloc to after RCU grace period")
Reported-by: syzbot+1989ee16d94720836244@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240602182703.207276-1-xiyou.wangcong@gmail.com
The iterator variable dst cannot be NULL and the if check can be removed.
Remove it and fix the following Coccinelle/coccicheck warning reported
by itnull.cocci:
ERROR: iterator variable bound on line 762 cannot be NULL
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240529101900.103913-2-thorsten.blum@toblux.com
When the PHY is powered up after powered down most of the registers are
reset, so the PHY setup code needs to be done again. In addition the
interrupt register will need to be setup again so that link status
indication works again.
Fixes: 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_CLOSE may or may not have current/rnext keys and should not be
considered "established". The fast-path for TCP_CLOSE is
SKB_DROP_REASON_TCP_CLOSE. This is what tcp_rcv_state_process() does
anyways. Add an early drop path to not spend any time verifying
segment signatures for sockets in TCP_CLOSE state.
Cc: stable@vger.kernel.org # v6.7
Fixes: 0a3a809089 ("net/tcp: Verify inbound TCP-AO signed segments")
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20240529-tcp_ao-sk_state-v1-1-d69b5d323c52@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently NCSI driver will send several NCSI commands back to back without
waiting the response of previous NCSI command or timeout in some state
when NIC have multi channel. This operation against the single thread
manner defined by NCSI SPEC(section 6.3.2.3 in DSP0222_1.1.1)
According to NCSI SPEC(section 6.2.13.1 in DSP0222_1.1.1), we should probe
one channel at a time by sending NCSI commands (Clear initial state, Get
version ID, Get capabilities...), than repeat this steps until the max
number of channels which we got from NCSI command (Get capabilities) has
been probed.
Fixes: e6f44ed6d0 ("net/ncsi: Package and channel management")
Signed-off-by: DelphineCCChiu <delphine_cc_chiu@wiwynn.com>
Link: https://lore.kernel.org/r/20240529065856.825241-1-delphine_cc_chiu@wiwynn.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
