Rafael reported:
I get the following error from 'make modules_install' on my test boxes:
HOSTCC firmware/ihex2fw
/home/rafael/src/linux-2.6/firmware/ihex2fw.c:268: fatal error: opening dependency file firmware/.ihex2fw.d: Read-only file system
compilation terminated.
make[3]: *** [firmware/ihex2fw] Error 1
make[2]: *** [_modinst_post] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
where the configuration is that the kernel is compiled on a build box
with 'make O=<destdir> -j5' and then <destdir> is mounted over NFS read-only by
each test box (full path to this directory is the same on the build box and on
the test boxes). Then, I cd into <destdir>, run 'make modules_install' and get
the error above.
The issue turns out to be that we when we install firmware pick
up the list of firmware blobs from firmware/Makefile.
And this triggers the Makefile rules to update ihex2fw.
There were two solutions for this issue:
1) Move the list of firmware blobs to a separate file
2) Avoid ihex2fw rebuild by moving it to scripts
As I seriously beleive that the list of firmware blobs should be
done in a fundamental different way solution 2) was selected.
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David Woodhouse <dwmw2@infradead.org>
On 2008-12-30 11:32:33, Sam Ravnborg wrote:
> We have added a few additional validation checks of the userspace headers:
...
> 3) We should include <linux/types.h> and not <asm/types.h>
> 4) If we use a __[us]{8,16,32,64} type then we must include <linux/types.h>
Satisfy these requirements for the linux/qnx*.h headers.
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The __SWAB_64_THRU_32__ case of a 64-bit byte swap was depending on the
no-longer-existant ___swab32() method (three underscores). We got rid
of some of the worst indirection and complexity, and now it should just
use the 32-bit swab function that was defined right above it.
Reported-and-tested-by: Nicolas Pitre <nico@cam.org>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implementation caused problems in userspace which can, and does
define _both_ __LITTLE_ENDIAN and __BIG_ENDIAN.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first step to make swab.h a regular header that will
include an asm/swab.h with arch overrides.
Avoid the gratuitous differences introduced in the new
linux/swab.h by naming the ___constant_swabXX bits and
__fswabXX bits exactly as found in the old implementation
in byteorder/swab[b].h
Use this new swab.h in byteorder/[big|little]_endian.h and
remove the two old swab headers.
Although the inclusion of asm/byteorder.h looks strange in
linux/swab.h, this will allow each arch to move the actual
arch overrides for the swab bits in an asm file and then
the includes can be cleaned up without requiring a flag day
for all arches at once.
Keep providing __fswabXX in case some userspace was using them
directly, but the revised __swabXX should be used instead in
any new code and will always do constant folding not dependent
on the optimization level, which means the __constant versions
can be phased out in-kernel.
Arches that use the old-style arch macros will lose their
optimized versions until they move to the new style, but at
least they will still compile. Many arches have already moved
and the patches to move the remaining arches are trivial.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: fix ordering of driver unload vs agp unload.
drm/i915: Respect the other stolen memory sizes we know of.
drm/i915: Non-mobile parts don't have integrated TV-out.
drm/i915: Add support for integrated HDMI on G4X hardware.
drm/i915: Pin cursor bo and unpin old bo when setting cursor.
drm/i915: Don't allow objects to get bound while VT switched.
This is ported directly from the userland 2D driver code. The HDMI audio bits
aren't hooked up yet.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We also didn't track the cursor bo before and would leak a reference
when the cursor image was change.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This avoids a BUG_ON in the enter_vt path due to objects being in the GTT
when we shouldn't have ever let them be (as we're not supposed to touch the
device during that time).
This was triggered by a change in the 2D driver to use the GTT mapping of
objects after pinning them to improve software fallback performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
CRED: Fix regression in cap_capable() as shown up by sys_faccessat() [ver #3]
Revert "CRED: Fix regression in cap_capable() as shown up by sys_faccessat() [ver #2]"
SELinux: shrink sizeof av_inhert selinux_class_perm and context
CRED: Fix regression in cap_capable() as shown up by sys_faccessat() [ver #2]
keys: fix sparse warning by adding __user annotation to cast
smack: Add support for unlabeled network hosts and networks
selinux: Deprecate and schedule the removal of the the compat_net functionality
netlabel: Update kernel configuration API
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix section mismatch
sched: fix double kfree in failure path
sched: clean up arch_reinit_sched_domains()
sched: mark sched_create_sysfs_power_savings_entries() as __init
getrusage: RUSAGE_THREAD should return ru_utime and ru_stime
sched: fix sched_slice()
sched_clock: prevent scd->clock from moving backwards, take #2
sched: sched.c declare variables before they get used
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: provide irq_to_desc() to non-genirq architectures too
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: fix rcutorture bug
rcu: eliminate synchronize_rcu_xxx macro
rcu: make treercu safe for suspend and resume
rcu: fix rcutree grace-period-latency bug on small systems
futex: catch certain assymetric (get|put)_futex_key calls
futex: make futex_(get|put)_key() calls symmetric
locking, percpu counters: introduce separate lock classes
swiotlb: clean up EXPORT_SYMBOL usage
swiotlb: remove unnecessary declaration
swiotlb: replace architecture-specific swiotlb.h with linux/swiotlb.h
swiotlb: add support for systems with highmem
swiotlb: store phys address in io_tlb_orig_addr array
swiotlb: add hwdev to swiotlb_phys_to_bus() / swiotlb_sg_to_bus()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Fix SND_SOC_ALL_CODECS handling of dual SPI and I2C control buses
ASoC: Use snd_soc_dapm_nc_pin() in at91sam9g20ek
ASoC: TWL4030: Convert the bitfield enums to VALUE_ENUM type
ASoC: New enum type: value_enum
pxa2xx-ac97: switch AC unit to correct state before probing
ASoC: Clocking fixes for davinci-evm.c
ASoC: Mark non-connected TWL4030 pins for pandora
ASoC: OMAP: Select OMAP pin multiplexing when using Nokia N810 ASoC drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: clean up annotations of fc->lock
fuse: fix sparse warning in ioctl
fuse: update interface version
fuse: add fuse_conn->release()
fuse: separate out fuse_conn_init() from new_conn()
fuse: add fuse_ prefix to several functions
fuse: implement poll support
fuse: implement unsolicited notification
fuse: add file kernel handle
fuse: implement ioctl support
fuse: don't let fuse_req->end() put the base reference
fuse: move FUSE_MINOR to miscdevice.h
fuse: style fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (41 commits)
scc_pata: make use of scc_dma_sff_read_status()
ide-dma-sff: factor out ide_dma_sff_write_status()
ide: move read_sff_dma_status() method to 'struct ide_dma_ops'
ide: don't set hwif->dma_ops in init_dma() method
Resurrect IT8172 IDE controller driver
piix: sync ich_laptop[] with ata_piix.c
ide: update warm-plug HOWTO
ide: fix ide_port_scan() to do ACPI setup after initializing request queues
ide: remove now redundant ->cur_dev checks
ide: remove unused ide_hwif_t.sg_mapped field
ide: struct ide_atapi_pc - remove unused fields and update documentation
ide: remove superfluous hwif variable assignment from ide_timer_expiry()
ide: use ide_pci_is_in_compatibility_mode() helper in setup-pci.c
ide: make "paranoia" ->handler check in ide_intr() more strict
ide-cd: convert to ide-atapi facilities
ide-cd: start DMA before sending the actual packet command
ide-cd: wait for DRQ to get set per default
ide: Fix drive's DWORD-IO handling
ide: add port and host iterators
ide: dynamic allocation of device structures
...
Use del_timer_sync() instead of del_timer() to make sure the timer won't
be running when we return from parport_wait_event(), because this would
crash due to destruction of timer_list.
This is untested and just based on a code review. Just think about the
following sequence of events:
- add_timer()
- down_interruptible() is interrupted by a signal.
- we enter the timer callback handler on another CPU.
- del_timer(), but the timer callback is still running.
- eturn from parport_wait_even, which destroys the automatic variable
"timer" while the callback is running on another CPU.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since all sanity checks rely on the validity of s_start which gets only
checked to be smaller than s_end, we should also check if s_end is sane.
Now we also try to retrieve the last block of the filesystem, which is
computed by s_end. If this fails, something is bogus.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bfs_fill_super() already touches all inodes, so we can easily add some
cheap sanity checks and check if the inode start and end blocks are
smaller than the maximum number of blocks, the inode start block lies
behind the end block or the file end offset is behind the end of the
filesystem. Also check if the start of data offset in the super block
fits the filesystem.
The added sanity checks catch softlockup issues early when we try to
sb_bread() lots of blocks in a loop in bfs_readdir() and bfs_find_entry().
In addition an oom issue in bfs_fill_super() is prevented by this when
s_start is corrupted, which influences imap_len and we try to allocate a
huge info->si_imap.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent passing an order to bitmap_find_free_region() that is larger than
the actual bitmap can represent.
These requests can come from device drivers that have no idea how big the
dma region is and need to rely on dma_alloc_from_coherent() to sort it out
for them.
Reported-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This thing was rather stupidly coded. Rework it all prior to making
changes.
Also, rename local variable `page': kernel readers expect something called
`page' to have type `struct page *'.
Cc: Guennadi Liakhovetski <lg@denx.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If bitmap_find_free_region() fails and DMA_MEMORY_EXCLUSIVE is not set,
the function will fail to write anything to *ret and will return 1. This will cause dma_alloc_coherent() to return an uninitialised value,
crashing the kernel, perhaps via DMA to a random address.
Fix that by changing it to return zero in this case, so the caller will
proceed to allocate the memory from the generic memory allocator.
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All other compatibles that are uniquely identifying the processor use a
prefix of the form fsl,mpc85...'. We add support for it so we can
deprecate the older 'fsl,85...' that was improperly used here.
Additionally added mpc8536 & mpc8560 to the compatible lists.
This patch is based on Nate's 8572 patch.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of a larger patch series which will remove the "char
bus_id[20]" name string from struct device. The device name is managed in
the kobject anyway, and without any size limitation, and just needlessly
copied into "struct device".
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
