We always hit the goto and skip the printk(). The original code does
the right thing even though it looks messy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.
Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.
While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the driver no longer uses the raw r/w routines, remove their definitions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe driver used raw reads and writes on the PCIe hardware.
As all of these are only affecting the configuration space, all of
then can be converted to pci_{read,write}_config_XX calls.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add code to display driver version information in dmesg after
loading the driver successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO card is now fully powered down when the network interface is
brought down.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the driver so that it does not function when the interface is
down, in preparation for runtime power management.
No commands can be run while the interface is down, so the ndo_dev_stop
routine now directly does all necessary work (including asking the device
to disconnect from the network and disabling multicast functionality)
directly.
power_save and power_restore hooks are added meaning that card drivers
can take steps to turn the device off when the interface is down.
The MAC address can now only be changed when all interfaces are down;
the new address will be programmed when an interface gets brought up.
This matches mac80211 behaviour.
Also, some small cleanups/simplifications were made in the surrounding
device handling logic.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (ath9k for example) are using skb->protocol to treat EAPOL
frames somehow special (disallow aggregation for example).
When running in AP mode hostapd injects the EAPOL frames through a
monitor interface and thus skb->protocol isn't set at all. Hence, if the
injected frame is a data frame and carries a rfc1042 headaer update the
skb->protocol field accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several uses were missing terminating newlines.
Typo fix and macro neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ieee80211 core was found on a Netgear wndr3400.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are SPROM specific, so all should be defined in ssb code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k presents the internal calibrated noise floor as channel
noise measurement, however this results in highly chip specific values
that are only useful as relative measurements but do not resemble any
real channel noise values.
In order to give a much better approximation of the real channel noise,
add the difference between the measured noise floor and the nominal
chip specific noise floor to the default minimum channel noise value,
which is currently used to calculate the signal strength from the RSSI
value. This may not be 100% accurate, but it's much better than what's
there before.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make mesh_preq_queue_lock locking consistent with mesh_queue_preq() using
spin_lock_bh().
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OLPC power management code has recently gone upstream. This piece
completes the puzzle for libertas_usb, which now programs the OLPC EC
for wlan wakeups when they have been requested.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing for tx power, bypass the default limits.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the previously calculated maximum of all rates instead of just the one
from the lowest rate of the selected PHY mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unnecessary includes from base.h. Add includes to other files as
necessary. Don't include base.h unless needed.
Move declarations for functions in base.c from ath5k.h to base.h.
Use a better named define to protect base.h against double inclusion.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID. Those have Agere firmware.
With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware. Cards with Agere firmware use
"Version 01.01".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to match wireless cards with Intersil firmware that have
ID 0x0156:0x0002 and the third ID "Version 01.02". Such cards are
currently matched by orinoco_cs, which doesn't support WPA. They should
be matched by hostap_cs.
The first and the second product ID vary widely, so there are few users
with some particular IDs. Of those, very few can submit a patch for
hostap_cs or write a useful bugreport. It's still important to support
their hardware properly.
With PCMCIA_DEVICE_MANF_CARD_PROD_ID3, it should be possible to cover
the remaining Intersil based designs that kept the numeric ID and the
"version" of the reference design.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to 802.11-2007, 7.3.1.14 it is compliant to use a buf_size of
0 in ADDBA requests. But some devices (AVM Fritz Stick N) arn't able to
handle that correctly and will reply with an ADDBA reponse with a
buf_size of 0 which in turn will disallow BA sessions for these
devices.
To work around this problem, initialize hw.max_tx_aggregation_subframes
to the maximum AMPDU buffer size 0x40.
Using 0 as default for the bufsize was introduced in commit
5dd36bc933 (mac80211: allow advertising
correct maximum aggregate size).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we receive an ADDBA response with status code 0 and a buf_size of 0
we should stop the TX BA session as otherwise we'll end up queuing
frames in ieee80211_tx_prep_agg forever instead of sending them out as
non AMPDUs.
This fixes a problem with AVM Fritz Stick N wireless devices where
frames to this device are not transmitted anymore by mac80211.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices supported by b43legacy don't support 64-bit DMA.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for v2 of enhanced sensitivity table for 2000 series products
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the default sensitivity value for both 5000 and 6000 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For iwlwifi, I decided not to use this API since
it just increased the complexity for little gain.
Since nobody else intends to use it, let's kill
it again. If anybody later needs to have it, we
can always revive it then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous P2P implementation turned out to
not work well and new uCode capabilities were
added to support P2P. Modify the driver to
take advantage of those, and also discover P2P
support automatically based on a uCode flag
instead of having a Kconfig symbol for P2P.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The availability of contexts depends on the
firmware capabilities. Currently only the
presence of the second context depends on it,
but soon P2P support will also be different.
Move the context initialisation code to the
firmware-dependent setup before registering
with mac80211 to make it easier to handle.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
