Add (incomplete) support for the ZTE UART to the AMBA PL011 driver.
This is similar to the ARM and ST variants, except it has a different
register address layout, and requires 32-bit accesses to the registers.
Use the newly introduced register tables and access size support to
cope with these differences.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for 32-bit register accesses to the AMBA PL011 UART. This
is needed for ZTE UARTs, which require 32-bit accesses as opposed to
the more normal 16-bit accesses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the ST micro registers from the standard table. These registers
should never be accessed in non-ST micro variants.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we can detect when the LCR register is split between TX and RX,
we don't need three entries in the table to deal with this. Reduce
this down to two entries by converting the REG_ST_LCRH_* entries to
standard REG_LCRH_* and remove REG_LCRH.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ST variant register offset table to the driver. Currently,
this is an identical copy of the standard version, but this will be
modified in the following changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the register offset table to the vendor data, allowing vendor
differences to be described in this table.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a register lookup table, which allows the register offsets to be
adjusted on a per-port basis.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the of-serial driver is now 8250 specific, we can move the
file to a more appropriate place in teh 8250 subdirectory and
adapt the Kconfig help text and file name.
I'm leaving the CONFIG_SERIAL_OF_PLATFORM symbol unchanged
to avoid breaking user configuration files unnecessarily.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only other user of this code was the nwp-serial driver, but that
is now gone, so we can remove a couple of #ifdef statments in this
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NWP serial driver is no longer needed, as the two users of
this hardware have migrated to a much faster generation hardware,
see https://en.wikipedia.org/wiki/QPACE2 for the replacement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Krill <ben@codiert.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bfin-uart code uses real time with struct timeval. This will
cause problems on 32-bit architectures in 2038 when time_t
overflows.
Since the code just needs delta value of time, it is not
necessary to record them in real time.
This patch changes the code to use the monotonic time instead,
replaces struct timeval and do_gettimeofday() with u64 and
ktime_get_ns().
Signed-off-by: DengChao <chao.deng@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `atmel_release_rx_dma':
atmel_serial.c:(.text+0x2502e): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `atmel_release_tx_dma':
atmel_serial.c:(.text+0x25080): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `atmel_tx_dma':
atmel_serial.c:(.text+0x2517a): undefined reference to `dma_sync_sg_for_cpu'
drivers/built-in.o: In function `atmel_release_tx_pdc':
atmel_serial.c:(.text+0x252e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_prepare_tx_pdc':
atmel_serial.c:(.text+0x2531a): undefined reference to `dma_map_single'
drivers/built-in.o: In function `atmel_release_rx_pdc':
atmel_serial.c:(.text+0x25362): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_tx_pdc':
atmel_serial.c:(.text+0x25722): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_rx_from_pdc':
atmel_serial.c:(.text+0x2601a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_rx_from_dma':
atmel_serial.c:(.text+0x261b2): undefined reference to `dma_sync_sg_for_cpu'
atmel_serial.c:(.text+0x26264): undefined reference to `dma_sync_sg_for_cpu'
drivers/built-in.o: In function `atmel_prepare_rx_pdc':
atmel_serial.c:(.text+0x262de): undefined reference to `dma_unmap_single'
atmel_serial.c:(.text+0x26308): undefined reference to `dma_map_single'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found that our sc16is7xx on spi reported a TX fifo free space value
(TXLVL_REG) of 255 ocassionally, which is obviously wrong, with a
64 byte fifo and caused a buffer overrun and a kernel crash.
To trigger this, a large write to the tty is sufficient. The fifo fills,
TXLVL_REG reads zero, but the handle_tx function does a zero-data-length
write to the TX fifo anyways through sc16is7xx_fifo_write. The next
TXLVL_REG read then yields 255, for unknown reasons. A subsequent read
is ok.
Prevent zero-data-length writes if the TX fifo is full, because they are
pointless, and because they trigger wrong TXLVL read-outs.
Furthermore, prevent a TX buffer overrun if the peripheral reports values
larger than the buffer size and thus, don't allow the peripheral to crash
the kernel.
Signed-off-by: Florian Achleitner <achleitner.florian@fronius.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SERIAL_DO_RESTART is not used by these 3 drivers; remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for REG_* register accessors. This change involves introducing
pl011_reg_to_offset() to convert REG_* to the hardware register offset,
and converting all call sites to use REG_* names. We need to fix up
locations where we check for equivalence of register offsets as well.
Much of this change was made via these sed expressions:
s/ST_UART01[1x]\(_[^_]*\|_LCRH_[TR]X\)\>/REG_ST\1/
s/UART01[1x]_\(DR\|RSR\|ECR\|FR\|ILPR\|[IF]BRD\|LCRH\|CR\|IFLS\|IMSC\|RIS\|MIS\|ICR\|DMACR\)\>/REG_\1/g
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to detect the split LCRH register found on ST variants.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the new accessor functions to take the uart_amba_port instead
of the port base address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add register accessor functions to amba-pl011. Much of this
transformation was done using the sed expression below, with any
left-overs fixed up manually afterwards, and code formatted to remain
within coding style.
s/readw(\(uap->port.membase\|regs\|port->membase\) +/pl011_read(\1,/g
s/writew(\(.*\) +/pl011_write(\1,/g
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, 8-bit (MMIO) and 32-bit (MMIO32) register interfaces are
supported for the 8250 console, but the 16-bit (MMIO16) is not.
The 8250 UART device on my board is connected to a 16-bit bus and
my main motivation is to use earlycon with it.
(Refer to arch/arm/boot/dts/uniphier-support-card.dtsi)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, wait_for_xmitr() is only called from serial_putc(), and both
are short enough. They can be merged into a single function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code waits until the transmitter becomes empty,
before sending each character, and after finishing the whole string.
This seems a bit redundant.
It can be more efficient by checking the transmitter only after sending
each character. This should be safe because the transmitter is already
empty at the first entry of serial_putc().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IER has already been masked in early_serial8250_setup(), there is
no reason to save and restore it every time early_serial8250_write()
is called.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This UART driver should not depend on the console. They should be
orthogonal.
Surround the earlycon code with CONFIG_SERIAL_EARLYCON conditional
and rip off "depends on SERIAL_8250_CONSOLE".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SERIAL_8250_INGENIC depends on SERIAL_8250_CONSOLE, which already
selects SERIAL_EARLYCON.
This line is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reuses the code of drivers/tty/serial/8250/8250_early.c except
- Overwrite device->port.iotype and device->port.regshift for
UPIO_MEM32 because of_setup_earlycon() has set them for UPIO_MEM.
- Set device->baud to zero to prevent early8250_setup() from
initializing the divisor register because port->uartclk does not
match the frequency expected by this hardware.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/8250/Kconfig:config SERIAL_8250_MT6577
drivers/tty/serial/8250/Kconfig: bool "Mediatek serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_ATMEL
drivers/tty/serial/Kconfig: bool "AT91 / AT32 on-chip serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that imx_mctrl_check is implemented below imx_get_mctrl the former
can call the latter directly instead of via sport->port.ops->get_mctrl.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .get_mctrl callback should not report the status of RTS or LOOP, so
drop this. Instead implement reporting the state of CAR (aka DCD) and
RI.
For .set_mctrl implement setting the DTR line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit replaces every instance of the string "jsm"
in the driver with JSM_DRIVER_NAME, as the two are
equivalent. This should increase overall consistency.
Signed-off-by: Gavin Thomas Claugus <gclaugus@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl8250_handle_irq is now used by the of_serial driver, and that fails
if it is a loadable module:
ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined!
This exports the symbol to avoid randconfig errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d43b54d269 ("serial: Enable Freescale 16550 workaround on arm")
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_mid uses rational_best_approximation() function, so the
driver needs to select CONFIG_RATIONAL option.
This fixes build error when CONFIG_RATIONAL is not enabled:
drivers/built-in.o: In function `mid8250_set_termios':
8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlycon support for Freescale lpuart should only be enabled when
console support is enabled.
Fixes: 1d59b382f1 ("serial: fsl_lpuart: add earlycon support")
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the device name when registering an interrupt so that multiple
ports don't all have the same interrupt name.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
