There is a desire to make the object and FDB replay helpers optional
when moving them inside the bridge driver. For example a certain driver
might not offload host MDBs and there is no case where the replay
helpers would be of immediate use to it.
So it would be nice if we could allow drivers to pass NULL pointers for
the atomic and blocking notifier blocks, and the replay helpers to do
nothing in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hwdoms have only been used thus far for equality comparisons, the
bridge has used the simplest possible assignment policy; using a
counter to keep track of the last value handed out.
With the upcoming transmit offloading, we need to perform set
operations efficiently based on hwdoms, e.g. we want to answer
questions like "has this skb been forwarded to any port within this
hwdom?"
Move to a bitmap-based allocation scheme that recycles hwdoms once all
members leaves the bridge. This means that we can use a single
unsigned long to keep track of the hwdoms that have received an skb.
v1->v2: convert the typedef DECLARE_BITMAP(br_hwdom_map_t, BR_HWDOM_MAX)
into a plain unsigned long.
v2->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, four related - but distinct - concepts where named
offload_fwd_mark:
- skb->offload_fwd_mark: Set by the switchdev driver if the underlying
hardware has already forwarded this frame to the other ports in the
same hardware domain.
- nbp->offload_fwd_mark: An idetifier used to group ports that share
the same hardware forwarding domain.
- br->offload_fwd_mark: Counter used to make sure that unique IDs are
used in cases where a bridge contains ports from multiple hardware
domains.
- skb->cb->offload_fwd_mark: The hardware domain on which the frame
ingressed and was forwarded.
Introduce the term "hardware forwarding domain" ("hwdom") in the
bridge to denote a set of ports with the following property:
If an skb with skb->offload_fwd_mark set, is received on a port
belonging to hwdom N, that frame has already been forwarded to all
other ports in hwdom N.
By decoupling the name from "offload_fwd_mark", we can extend the
term's definition in the future - e.g. to add constraints that
describe expected egress behavior - without overloading the meaning of
"offload_fwd_mark".
- nbp->offload_fwd_mark thus becomes nbp->hwdom.
- br->offload_fwd_mark becomes br->last_hwdom.
- skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight
change in naming here mandates a slight change in behavior of the
nbp_switchdev_frame_mark() function. Previously, it only set this
value in skb->cb for packets with skb->offload_fwd_mark true (ones
which were forwarded in hardware). Whereas now we always track the
incoming hwdom for all packets coming from a switchdev (even for the
packets which weren't forwarded in hardware, such as STP BPDUs, IGMP
reports etc). As all uses of skb->cb->offload_fwd_mark were already
gated behind checks of skb->offload_fwd_mark, this will not introduce
any functional change, but it paves the way for future changes where
the ingressing hwdom must be known for frames coming from a switchdev
regardless of whether they were forwarded in hardware or not
(basically, if the skb comes from a switchdev, skb->cb->src_hwdom now
always tracks which one).
A typical example where this is relevant: the switchdev has a fixed
configuration to trap STP BPDUs, but STP is not running on the bridge
and the group_fwd_mask allows them to be forwarded. Say we have this
setup:
br0
/ | \
/ | \
swp0 swp1 swp2
A BPDU comes in on swp0 and is trapped to the CPU; the driver does not
set skb->offload_fwd_mark. The bridge determines that the frame should
be forwarded to swp{1,2}. It is imperative that forward offloading is
_not_ allowed in this case, as the source hwdom is already "poisoned".
Recording the source hwdom allows this case to be handled properly.
v2->v3: added code comments
v3->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make more room for some extra code in the NETDEV_PRECHANGEUPPER handler
by moving what already exists into a dedicated function.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to propagate the extack argument for
dpaa2_switch_port_bridge_join to use it in a future patch, and it looks
like there is already an error message there which is currently printed
to the console. Move it over netlink so it is properly transmitted to
user space.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure to register devlink will leave the system with dangled
devlink resource, which is not cleaned if devlink_port_register() fails.
In order to remove access to ".registered" field of struct devlink_port,
require both devlink_register and devlink_port_register to success and
check it through device pointer.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge multicast context support for host-joined groups is easy
because we only need the proper timer value. We pass the already chosen
context and use its timer value.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose the proper bridge multicast context when user-spaces is adding
mdb entries. Currently we require the vlan to be configured on at least
one device (port or bridge) in order to add an mdb entry if vlan
mcast snooping is enabled (vlan snooping implies vlan filtering).
Note that we always allow deleting an entry, regardless of the vlan state.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes issues found by dtbs_check:
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/fsl,fec.yaml
According to the Micrel PHY dt-binding:
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt,
Add clock delay in an Ethernet OF device node is deprecated, so move
these properties to PHY OF device node.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the yaml a bit according to Rob Herring comments:
1) normalize interrupt-names property, there is no reason to support
random order.
2) validate each string in clock-names property.
3) add constraints for fsl,num-tx-queues/fsl,num-rx-queues property.
4) change additionalProperties to false in order to do strict checking.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_grow_window() is using skb->len/skb->truesize to increase tp->rcv_ssthresh
which has a direct impact on advertized window sizes.
We added TCP coalescing in linux-3.4 & linux-3.5:
Instead of storing skbs with one or two MSS in receive queue (or OFO queue),
we try to append segments together to reduce memory overhead.
High performance network drivers tend to cook skb with 3 parts :
1) sk_buff structure (256 bytes)
2) skb->head contains room to copy headers as needed, and skb_shared_info
3) page fragment(s) containing the ~1514 bytes frame (or more depending on MTU)
Once coalesced into a previous skb, 1) and 2) are freed.
We can therefore tweak the way we compute len/truesize ratio knowing
that skb->truesize is inflated by 1) and 2) soon to be freed.
This is done only for in-order skb, or skb coalesced into OFO queue.
The result is that low rate flows no longer pay the memory price of having
low GRO aggregation factor. Same result for drivers not using GRO.
This is critical to allow a big enough receiver window,
typically tcp_rmem[2] / 2.
We have been using this at Google for about 5 years, it is due time
to make it upstream.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to use bridge/port multicast context pointers
instead of bridge/port I missed to convert two locations which pass the
port pointer as-is, but with the new model we need to verify the port
context is non-NULL first and retrieve the port from it. The first
location is when doing querier selection when a query is received, the
second location is when leaving a group. The port context will be null
if the packets originated from the bridge device (i.e. from the host).
The fix is simple just check if the port context exists and retrieve
the port pointer from it.
Fixes: adc47037a7 ("net: bridge: multicast: use multicast contexts instead of bridge or port")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core will call to .remove callback only if .probe succeeded
and it will ensure that driver data has pointer to struct ionic.
There is no need to check it again.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tcp sockets, sk->sk_write_space is most probably sk_stream_write_space().
Other sk->sk_write_space() calls in TCP are slow path and do not deserve
any change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some boilerplate code by using module_pci_driver() instead of
init/exit, moving the salient bits from init into probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bf ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate IPv4 MTU code the same way it is done in IPv6 to have code
aligned in both address families
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ip6_dst_mtu_forward with ip6_dst_mtu_maybe_forward and
reuse this code in ip6_mtu. Actually these two functions were
almost duplicates, this change will simplify the maintaince of
mtu calculation code.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Iurman says:
====================
Support for the IOAM Pre-allocated Trace with IPv6
v5:
- Refine types, min/max and default values for new sysctls
- Introduce a "_wide" sysctl for each "ioam6_id" sysctl
- Add more validation on headers before processing data
- RCU for sc <> ns pointers + appropriate accessors
- Generic Netlink policies are now per op, not per family anymore
- Address other comments/remarks from Jakub (thanks again)
- Revert "__packed" to "__attribute__((packed))" for uapi headers
- Add tests to cover the functionality added, as requested by David Ahern
v4:
- Address warnings from checkpatch (ignore errors related to unnamed bitfields
in the first patch)
- Use of hweight32 (thanks Jakub)
- Remove inline keyword from static functions in C files and let the compiler
decide what to do (thanks Jakub)
v3:
- Fix warning "unused label 'out_unregister_genl'" by adding conditional macro
- Fix lwtunnel output redirect bug: dst cache useless in this case, use
orig_output instead
v2:
- Fix warning with static for __ioam6_fill_trace_data
- Fix sparse warning with __force when casting __be64 to __be32
- Fix unchecked dereference when removing IOAM namespaces or schemas
- exthdrs.c: Don't drop by default (now: ignore) to match the act bits "00"
- Add control plane support for the inline insertion (lwtunnel)
- Provide uapi structures
- Use __net_timestamp if skb->tstamp is empty
- Add note about the temporary IANA allocation
- Remove support for "removable" TLVs
- Remove support for virtual/anonymous tunnel decapsulation
In-situ Operations, Administration, and Maintenance (IOAM) records
operational and telemetry information in a packet while it traverses
a path between two points in an IOAM domain. It is defined in
draft-ietf-ippm-ioam-data [1]. IOAM data fields can be encapsulated
into a variety of protocols. The IPv6 encapsulation is defined in
draft-ietf-ippm-ioam-ipv6-options [2], via extension headers. IOAM
can be used to complement OAM mechanisms based on e.g. ICMP or other
types of probe packets.
This patchset implements support for the Pre-allocated Trace, carried
by a Hop-by-Hop. Therefore, a new IPv6 Hop-by-Hop TLV option is
introduced, see IANA [3]. The three other IOAM options are not included
in this patchset (Incremental Trace, Proof-of-Transit and Edge-to-Edge).
The main idea behind the IOAM Pre-allocated Trace is that a node
pre-allocates some room in packets for IOAM data. Then, each IOAM node
on the path will insert its data. There exist several interesting use-
cases, e.g. Fast failure detection/isolation or Smart service selection.
Another killer use-case is what we have called Cross-Layer Telemetry,
see the demo video on its repository [4], that aims to make the entire
stack (L2/L3 -> L7) visible for distributed tracing tools (e.g. Jaeger),
instead of the current L5 -> L7 limited view. So, basically, this is a
nice feature for the Linux Kernel.
This patchset also provides support for the control plane part, but only for the
inline insertion (host-to-host use case), through lightweight tunnels. Indeed,
for in-transit traffic, the solution is to have an IPv6-in-IPv6 encapsulation,
which brings some difficulties and still requires a little bit of work and
discussion (ie anonymous tunnel decapsulation and multi egress resolution).
- Patch 1: IPv6 IOAM headers definition
- Patch 2: Data plane support for Pre-allocated Trace
- Patch 3: IOAM Generic Netlink API
- Patch 4: Support for IOAM injection with lwtunnels
- Patch 5: Documentation for new IOAM sysctls
- Patch 6: Test for the IOAM insertion with IPv6
[1] https://tools.ietf.org/html/draft-ietf-ippm-ioam-data
[2] https://tools.ietf.org/html/draft-ietf-ippm-ioam-ipv6-options
[3] https://www.iana.org/assignments/ipv6-parameters/ipv6-parameters.xhtml#ipv6-parameters-2
[4] https://github.com/iurmanj/cross-layer-telemetry
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This test evaluates the IOAM insertion for IPv6 by checking the IOAM data
integrity on the receiver.
The topology is formed by 3 nodes: Alpha (sender), Beta (router in-between)
and Gamma (receiver). An IOAM domain is configured from Alpha to Gamma only,
which means not on the reverse path. When Gamma is the destination, Alpha
adds an IOAM option (Pre-allocated Trace) inside a Hop-by-hop and fills the
trace with its own IOAM data. Beta and Gamma also fill the trace. The IOAM
data integrity is checked on Gamma, by comparing with the pre-defined IOAM
configuration (see below).
+-------------------+ +-------------------+
| | | |
| alpha netns | | gamma netns |
| | | |
| +-------------+ | | +-------------+ |
| | veth0 | | | | veth0 | |
| | db01::2/64 | | | | db02::2/64 | |
| +-------------+ | | +-------------+ |
| . | | . |
+-------------------+ +-------------------+
. .
. .
. .
+----------------------------------------------------+
| . . |
| +-------------+ +-------------+ |
| | veth0 | | veth1 | |
| | db01::1/64 | ................ | db02::1/64 | |
| +-------------+ +-------------+ |
| |
| beta netns |
| |
+--------------------------+-------------------------+
~~~~~~~~~~~~~~~~~~~~~~
| IOAM configuration |
~~~~~~~~~~~~~~~~~~~~~~
Alpha
+-----------------------------------------------------------+
| Type | Value |
+-----------------------------------------------------------+
| Node ID | 1 |
+-----------------------------------------------------------+
| Node Wide ID | 11111111 |
+-----------------------------------------------------------+
| Ingress ID | 0xffff (default value) |
+-----------------------------------------------------------+
| Ingress Wide ID | 0xffffffff (default value) |
+-----------------------------------------------------------+
| Egress ID | 101 |
+-----------------------------------------------------------+
| Egress Wide ID | 101101 |
+-----------------------------------------------------------+
| Namespace Data | 0xdeadbee0 |
+-----------------------------------------------------------+
| Namespace Wide Data | 0xcafec0caf00dc0de |
+-----------------------------------------------------------+
| Schema ID | 777 |
+-----------------------------------------------------------+
| Schema Data | something that will be 4n-aligned |
+-----------------------------------------------------------+
Note: When Gamma is the destination, Alpha adds an IOAM Pre-allocated Trace
option inside a Hop-by-hop, where 164 bytes are pre-allocated for the
trace, with 123 as the IOAM-Namespace and with 0xfff00200 as the trace
type (= all available options at this time). As a result, and based on
IOAM configurations here, only both Alpha and Beta should be capable of
inserting their IOAM data while Gamma won't have enough space and will
set the overflow bit.
Beta
+-----------------------------------------------------------+
| Type | Value |
+-----------------------------------------------------------+
| Node ID | 2 |
+-----------------------------------------------------------+
| Node Wide ID | 22222222 |
+-----------------------------------------------------------+
| Ingress ID | 201 |
+-----------------------------------------------------------+
| Ingress Wide ID | 201201 |
+-----------------------------------------------------------+
| Egress ID | 202 |
+-----------------------------------------------------------+
| Egress Wide ID | 202202 |
+-----------------------------------------------------------+
| Namespace Data | 0xdeadbee1 |
+-----------------------------------------------------------+
| Namespace Wide Data | 0xcafec0caf11dc0de |
+-----------------------------------------------------------+
| Schema ID | 0xffffff (= None) |
+-----------------------------------------------------------+
| Schema Data | |
+-----------------------------------------------------------+
Gamma
+-----------------------------------------------------------+
| Type | Value |
+-----------------------------------------------------------+
| Node ID | 3 |
+-----------------------------------------------------------+
| Node Wide ID | 33333333 |
+-----------------------------------------------------------+
| Ingress ID | 301 |
+-----------------------------------------------------------+
| Ingress Wide ID | 301301 |
+-----------------------------------------------------------+
| Egress ID | 0xffff (default value) |
+-----------------------------------------------------------+
| Egress Wide ID | 0xffffffff (default value) |
+-----------------------------------------------------------+
| Namespace Data | 0xdeadbee2 |
+-----------------------------------------------------------+
| Namespace Wide Data | 0xcafec0caf22dc0de |
+-----------------------------------------------------------+
| Schema ID | 0xffffff (= None) |
+-----------------------------------------------------------+
| Schema Data | |
+-----------------------------------------------------------+
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for new IOAM sysctls:
- ioam6_id and ioam6_id_wide: two per-namespace sysctls
- ioam6_enabled, ioam6_id and ioam6_id_wide: three per-interface sysctls
Example of IOAM configuration based on the following simple topology:
_____ _____ _____
| | eth0 eth0 | | eth1 eth0 | |
| A |.----------.| B |.----------.| C |
|_____| |_____| |_____|
1) Node and interface IDs can be configured for IOAM:
# IOAM ID of A = 1, IOAM ID of A.eth0 = 11
(A) sysctl -w net.ipv6.ioam6_id=1
(A) sysctl -w net.ipv6.conf.eth0.ioam6_id=11
# IOAM ID of B = 2, IOAM ID of B.eth0 = 21, IOAM ID of B.eth1 = 22
(B) sysctl -w net.ipv6.ioam6_id=2
(B) sysctl -w net.ipv6.conf.eth0.ioam6_id=21
(B) sysctl -w net.ipv6.conf.eth1.ioam6_id=22
# IOAM ID of C = 3, IOAM ID of C.eth0 = 31
(C) sysctl -w net.ipv6.ioam6_id=3
(C) sysctl -w net.ipv6.conf.eth0.ioam6_id=31
Note that "_wide" IDs equivalents can be configured the same way.
2) Each node can be configured to form an IOAM domain. For instance,
we allow IOAM from A to C only (not the reverse path), i.e. enable
IOAM on ingress for B.eth0 and C.eth0:
(B) sysctl -w net.ipv6.conf.eth0.ioam6_enabled=1
(C) sysctl -w net.ipv6.conf.eth0.ioam6_enabled=1
3) An IOAM domain (e.g. ID=123) is defined and made known to each node:
(A) ip ioam namespace add 123
(B) ip ioam namespace add 123
(C) ip ioam namespace add 123
4) Finally, an IOAM Pre-allocated Trace can be inserted in traffic sent
by A when C (e.g. db02::2) is the destination:
(A) ip -6 route add db02::2/128 encap ioam6 trace type 0x800000 ns 123
size 12 dev eth0
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the IOAM inline insertion (only for the host-to-host use case)
which is per-route configured with lightweight tunnels. The target is iproute2
and the patch is ready. It will be posted as soon as this patchset is merged.
Here is an overview:
$ ip -6 ro ad fc00::1/128 encap ioam6 trace type 0x800000 ns 1 size 12 dev eth0
This example configures an IOAM Pre-allocated Trace option attached to the
fc00::1/128 prefix. The IOAM namespace (ns) is 1, the size of the pre-allocated
trace data block is 12 octets (size) and only the first IOAM data (bit 0:
hop_limit + node id) is included in the trace (type) represented as a bitfield.
The reason why the in-transit (IPv6-in-IPv6 encapsulation) use case is not
implemented is explained on the patchset cover.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Generic Netlink commands to allow userspace to configure IOAM
namespaces and schemas. The target is iproute2 and the patch is ready.
It will be posted as soon as this patchset is merged. Here is an overview:
$ ip ioam
Usage: ip ioam { COMMAND | help }
ip ioam namespace show
ip ioam namespace add ID [ data DATA32 ] [ wide DATA64 ]
ip ioam namespace del ID
ip ioam schema show
ip ioam schema add ID DATA
ip ioam schema del ID
ip ioam namespace set ID schema { ID | none }
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for processing the IOAM Pre-allocated Trace with IPv6,
see [1] and [2]. Introduce a new IPv6 Hop-by-Hop TLV option, see IANA [3].
A new per-interface sysctl is introduced. The value is a boolean to accept (=1)
or ignore (=0, by default) IPv6 IOAM options on ingress for an interface:
- net.ipv6.conf.XXX.ioam6_enabled
Two other sysctls are introduced to define IOAM IDs, represented by an integer.
They are respectively per-namespace and per-interface:
- net.ipv6.ioam6_id
- net.ipv6.conf.XXX.ioam6_id
The value of the first one represents the IOAM ID of the node itself (u32; max
and default value = U32_MAX>>8, due to hop limit concatenation) while the other
represents the IOAM ID of an interface (u16; max and default value = U16_MAX).
Each "ioam6_id" sysctl has a "_wide" equivalent:
- net.ipv6.ioam6_id_wide
- net.ipv6.conf.XXX.ioam6_id_wide
The value of the first one represents the wide IOAM ID of the node itself (u64;
max and default value = U64_MAX>>8, due to hop limit concatenation) while the
other represents the wide IOAM ID of an interface (u32; max and default value
= U32_MAX).
The use of short and wide equivalents is not exclusive, a deployment could
choose to leverage both. For example, net.ipv6.conf.XXX.ioam6_id (short format)
could be an identifier for a physical interface, whereas
net.ipv6.conf.XXX.ioam6_id_wide (wide format) could be an identifier for a
logical sub-interface. Documentation about new sysctls is provided at the end
of this patchset.
Two relativistic hash tables are used: one for IOAM namespaces, the other for
IOAM schemas. A namespace can only have a single active schema and a schema
can only be attached to a single namespace (1:1 relationship).
[1] https://tools.ietf.org/html/draft-ietf-ippm-ioam-ipv6-options
[2] https://tools.ietf.org/html/draft-ietf-ippm-ioam-data
[3] https://www.iana.org/assignments/ipv6-parameters/ipv6-parameters.xhtml#ipv6-parameters-2
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the IPv6 IOAM option header [1] as well as the IOAM
Trace header [2]. An IOAM option must be 4n-aligned. Here is an overview of
a Hop-by-Hop with an IOAM Trace option:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next header | Hdr Ext Len | Padding | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option Type | Opt Data Len | Reserved | IOAM Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Namespace-ID | NodeLen | Flags | RemainingLen|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IOAM-Trace-Type | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
| | |
| node data [n] | |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ D
| | a
| node data [n-1] | t
| | a
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~ S
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ p
| | a
| node data [1] | c
| | e
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| | |
| node data [0] | |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
The IOAM option header starts at "Option Type" and ends after "IOAM
Type". The IOAM Trace header starts at "Namespace-ID" and ends after
"IOAM-Trace-Type/Reserved".
IOAM Type: either Pre-allocated Trace (=0), Incremental Trace (=1),
Proof-of-Transit (=2) or Edge-to-Edge (=3). Note that both the
Pre-allocated Trace and the Incremental Trace look the same. The two
others are not implemented.
Namespace-ID: IOAM namespace identifier, not to be confused with network
namespaces. It adds further context to IOAM options and associated data,
and allows devices which are IOAM capable to determine whether IOAM
options must be processed or ignored. It can also be used by an operator
to distinguish different operational domains or to identify different
sets of devices.
NodeLen: Length of data added by each node. It depends on the Trace
Type.
Flags: Only the Overflow (O) flag for now. The O flag is set by a
transit node when there are not enough octets left to record its data.
RemainingLen: Remaining free space to record data.
IOAM-Trace-Type: Bit field where each bit corresponds to a specific kind
of IOAM data. See [2] for a detailed list.
[1] https://tools.ietf.org/html/draft-ietf-ippm-ioam-ipv6-options
[2] https://tools.ietf.org/html/draft-ietf-ippm-ioam-data
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between __switchdev_handle_fdb_del_to_device and
switchdev_handle_del_to_device is that the former takes an extra
orig_dev argument, while the latter starts with dev == orig_dev.
We should recurse into the variant that does not lose the orig_dev along
the way. This is relevant when deleting FDB entries pointing towards a
bridge (dev changes to the lower interfaces, but orig_dev shouldn't).
The addition helper already recurses properly, just the deletion one
doesn't.
Fixes: 8ca07176ab ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the semicolon at the end, the compiler sees the shim function as a
declaration and not as a definition, and warns:
'switchdev_handle_fdb_del_to_device' declared 'static' but never defined
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8ca07176ab ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit was probably not tested on net-next, since it did not
refactor the extra phy id check introduced in commit b856150c80 ("net:
phy: at803x: mask 1000 Base-X link mode").
Fixes: 8887ca5474 ("net: phy: at803x: simplify custom phy id matching")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to fiddle about with the supported mask after we have
validated the user's requested parameters. Simplify and streamline the
code by moving the linkmode copy and update of the autoneg bit after
validating the user's request.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-07-20
This series contains updates to e1000e and igc drivers.
Sasha adds initial S0ix support for devices with CSME and adds polling
for exiting of DPG. He sets the PHY to low power idle when in S0ix. He
also adds support for new device IDs for and adds a space to debug
messaging to help with readability for e1000e.
For igc, he ensures that q_vector array is not accessed beyond its
bounds and removes unneeded PHY related checks.
Tree Davies corrects a spelling mistake in e1000e.
Muhammad corrects the value written when there is no TSN offloading
and adjusts timeout value to avoid possible Tx hang for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changs interrupt order which found by dtbs_check.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:0: 'macirq' was expected
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:1: 'eth_wake_irq' was expected
According to Documentation/devicetree/bindings/net/snps,dwmac.yaml, we
should list interrupt in it's order.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to automate the verification of DT nodes covert imx-dwmac to
nxp,dwmac-imx.yaml, and pass below checking.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing DWMAC IP version in snps,dwmac.yaml which found by below
command, as NXP i.MX8 families support SNPS DWMAC 5.10a IP.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
Documentation/devicetree/bindings/net/nxp,dwmac-imx.example.dt.yaml:
ethernet@30bf0000: compatible: None of ['nxp,imx8mp-dwmac-eqos', 'snps,dwmac-5.10a'] are valid under the given schema
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the cycle time is set to maximum of 1s, the TX Hang timeout need to
be increase to avoid possible TX Hang.
There is no dedicated number specific in data sheet for the timeout factor.
Timeout factor was determined during the debugging to solve the "Tx Hang"
issues that happen in some cases mainly during ETF(Earliest TxTime First).
This can be test by using TSN Schedule Tx Tools udp_tai sample application.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
According to datasheet section 8.12.19, when there's no TSN offloading
Shadow_QbvCycle bit[29:0] must be set to zero for basic scheduling.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one phy->type: copper. There is no point checking
phy->type during the igc_has_link method from the watchdog that
invoked every 2 seconds.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one PHY vendor. There is no point checking
_I_PHY_ID during the link establishment and auto-negotiation process.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a spelling mistake in the comment block.
Signed-off-by: Tree Davies <tdavies@darkphysics.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Minor fixes to allow debug prints more readable.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platforms
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platform (Lunar Lake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After transferring the MAC-PHY interface to the SMBus set the PHY
to S0ix low power idle mode.
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Per guidance from the CSME architecture team, it may take
up to 1 second for unconfiguring dynamic power gating mode.
Practically it can take more time. Wait up to 2.5 seconds to indicate
dynamic power gating exit from the S0ix configuration. Detect
scenarios that take more than 1 second but less than 2.5 seconds
will emit warning message.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On the corporate system, the driver will ask from the CSME
(manageability engine) to perform device settings are required
to allow S0ix residency.
This patch provides initial support.
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that in the driver's mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The character sequence ??! is a trigraph and causes the following
clang warning:
drivers/net/ethernet/marvell/mvneta.c:2604:39: warning: trigraph ignored [-Wtrigraphs]
Clean this by replacing it with single ?.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
