Removes some efx_ef10_nic_data references from common code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various MCDI functions (especially in filter handling) need to check the
datapath caps, but those live in nic_data (since they don't exist on
Siena). Decouple from ef10-specific data structures by adding check_caps
to the nic_type, to allow using these functions from non-ef10 drivers.
Also add a convenience macro efx_has_cap() to reduce the amount of
boilerplate involved in calling it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some usage of ef10-specific nic_data structs from common MCDI
functions, in preparation for using them from a non-EF10 driver.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bhupesh Sharma says:
====================
net: Optimize the qed* allocations inside kdump kernel
Changes since v1:
----------------
- v1 can be seen here: http://lists.infradead.org/pipermail/kexec/2020-May/024935.html
- Addressed review comments received on v1:
* Removed unnecessary paranthesis.
* Used a different macro for minimum RX/TX ring count value in kdump
kernel.
Since kdump kernel(s) run under severe memory constraint with the
basic idea being to save the crashdump vmcore reliably when the primary
kernel panics/hangs, large memory allocations done by a network driver
can cause the crashkernel to panic with OOM.
The qed* drivers take up approximately 214MB memory when run in the
kdump kernel with the default configuration settings presently used in
the driver. With an usual crashkernel size of 512M, this allocation
is equal to almost half of the total crashkernel size allocated.
See some logs obtained via memstrack tool (see [1]) below:
dracut-pre-pivot[676]: ======== Report format module_summary: ========
dracut-pre-pivot[676]: Module qed using 149.6MB (2394 pages), peak allocation 149.6MB (2394 pages)
dracut-pre-pivot[676]: Module qede using 65.3MB (1045 pages), peak allocation 65.3MB (1045 pages)
This patchset tries to reduce the overall memory allocation profile of
the qed* driver when they run in the kdump kernel. With these
optimization we can see a saving of approx 85M in the kdump kernel:
dracut-pre-pivot[671]: ======== Report format module_summary: ========
dracut-pre-pivot[671]: Module qed using 124.6MB (1993 pages), peak allocation 124.7MB (1995 pages)
<..snip..>
dracut-pre-pivot[671]: Module qede using 4.6MB (73 pages), peak allocation 4.6MB (74 pages)
And the kdump kernel can save vmcore successfully via both ssh and nfs
interfaces.
This patchset contains two patches:
[PATCH 1/2] - Reduces the default TX and RX ring count in kdump kernel.
[PATCH 2/2] - Disables qed SRIOV feature in kdump kernel (as it is
normally not a supported kdump target for saving
vmcore).
[1]. Memstrack tool: https://github.com/ryncsn/memstrack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have kdump kernel(s) running under severe memory constraint
it makes sense to disable the qed SRIOV functionality when running the
kdump kernel as kdump configurations on several distributions don't
support SRIOV targets for saving the vmcore (see [1] for example).
Currently the qed SRIOV functionality ends up consuming memory in
the kdump kernel, when we don't really use the same.
An example log seen in the kdump kernel with the SRIOV functionality
enabled can be seen below (obtained via memstrack tool, see [2]):
dracut-pre-pivot[676]: ======== Report format module_summary: ========
dracut-pre-pivot[676]: Module qed using 149.6MB (2394 pages), peak allocation 149.6MB (2394 pages)
This patch disables the SRIOV functionality inside kdump kernel and with
the same applied the memory consumption goes down:
dracut-pre-pivot[671]: ======== Report format module_summary: ========
dracut-pre-pivot[671]: Module qed using 124.6MB (1993 pages), peak allocation 124.7MB (1995 pages)
[1]. https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/8/html/managing_monitoring_and_updating_the_kernel/installing-and-configuring-kdump_managing-monitoring-and-updating-the-kernel#supported-kdump-targets_supported-kdump-configurations-and-targets
[2]. Memstrack tool: https://github.com/ryncsn/memstrack
Cc: kexec@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Cc: Manish Chopra <manishc@marvell.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally kdump kernel(s) run under severe memory constraint with the
basic idea being to save the crashdump vmcore reliably when the primary
kernel panics/hangs.
Currently the qed* ethernet driver ends up consuming a lot of memory in
the kdump kernel, leading to kdump kernel panic when one tries to save
the vmcore via ssh/nfs (thus utilizing the services of the underlying
qed* network interfaces).
An example OOM message log seen in the kdump kernel can be seen here
[1], with crashkernel size reservation of 512M.
Using tools like memstrack (see [2]), we can track the modules taking up
the bulk of memory in the kdump kernel and organize the memory usage
output as per 'highest allocator first'. An example log for the OOM case
indicates that the qed* modules end up allocating approximately 216M
memory, which is a large part of the total crashkernel size:
dracut-pre-pivot[676]: ======== Report format module_summary: ========
dracut-pre-pivot[676]: Module qed using 149.6MB (2394 pages), peak allocation 149.6MB (2394 pages)
dracut-pre-pivot[676]: Module qede using 65.3MB (1045 pages), peak allocation 65.3MB (1045 pages)
This patch reduces the default RX and TX ring count from 1024 to 64
when running inside kdump kernel, which leads to a significant memory
saving.
An example log with the patch applied shows the reduced memory
allocation in the kdump kernel:
dracut-pre-pivot[674]: ======== Report format module_summary: ========
dracut-pre-pivot[674]: Module qed using 141.8MB (2268 pages), peak allocation 141.8MB (2268 pages)
<..snip..>
[dracut-pre-pivot[674]: Module qede using 4.8MB (76 pages), peak allocation 4.9MB (78 pages)
Tested crashdump vmcore save via ssh/nfs protocol using underlying qed*
network interface after applying this patch.
[1] OOM log:
------------
kworker/0:6: page allocation failure: order:6,
mode:0x60c0c0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null)
kworker/0:6 cpuset=/ mems_allowed=0
CPU: 0 PID: 145 Comm: kworker/0:6 Not tainted 4.18.0-109.el8.aarch64 #1
Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL025
01/18/2019
Workqueue: events work_for_cpu_fn
Call trace:
dump_backtrace+0x0/0x188
show_stack+0x24/0x30
dump_stack+0x90/0xb4
warn_alloc+0xf4/0x178
__alloc_pages_nodemask+0xcac/0xd58
alloc_pages_current+0x8c/0xf8
kmalloc_order_trace+0x38/0x108
qed_iov_alloc+0x40/0x248 [qed]
qed_resc_alloc+0x224/0x518 [qed]
qed_slowpath_start+0x254/0x928 [qed]
__qede_probe+0xf8/0x5e0 [qede]
qede_probe+0x68/0xd8 [qede]
local_pci_probe+0x44/0xa8
work_for_cpu_fn+0x20/0x30
process_one_work+0x1ac/0x3e8
worker_thread+0x44/0x448
kthread+0x130/0x138
ret_from_fork+0x10/0x18
Cannot start slowpath
qede: probe of 0000:05:00.1 failed with error -12
[2]. Memstrack tool: https://github.com/ryncsn/memstrack
Cc: kexec@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Cc: Manish Chopra <manishc@marvell.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add set_link_ksettings implementation and improve the implementation
of get_link_ksettings
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
This series adds support for boards where DSA switches of multiple types
are cascaded together. Actually this type of setup was brought up before
on netdev, and it looks like utilizing disjoint trees is the way to go:
https://lkml.org/lkml/2019/7/7/225
The trouble with disjoint trees (prior to this patch series) is that only
bridging of ports within the same hardware switch can be offloaded.
After scratching my head for a while, it looks like the easiest way to
support hardware bridging between different DSA trees is to bridge their
DSA masters and extend the crosschip bridging operations.
I have given some thought to bridging the DSA masters with the slaves
themselves, but given the hardware topology described in the commit
message of patch 4/4, virtually any number (and combination) of bridges
(forwarding domains) can be created on top of those 3x4-port front-panel
switches. So it becomes a lot less obvious, when the front-panel ports
are enslaved to more than 1 bridge, which bridge should the DSA masters
be enslaved to.
So the least awkward approach was to just create a completely separate
bridge for the DSA masters, whose entire purpose is to permit hardware
forwarding between the discrete switches beneath it.
This is a direct resend of v3, which was deferred due to lack of review.
In the meantime Florian has reviewed and tested some of them.
v1 was submitted here:
https://patchwork.ozlabs.org/project/netdev/cover/20200429161952.17769-1-olteanv@gmail.com/
v2 was submitted here:
https://patchwork.ozlabs.org/project/netdev/cover/20200430202542.11797-1-olteanv@gmail.com/
v3 was submitted here:
https://patchwork.ozlabs.org/project/netdev/cover/20200503221228.10928-1-olteanv@gmail.com/
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sja1105 uses dsa_8021q for DSA tagging, a format which is VLAN at heart
and which is compatible with cascading. A complete description of this
tagging format is in net/dsa/tag_8021q.c, but a quick summary is that
each external-facing port tags incoming frames with a unique pvid, and
this special VLAN is transmitted as tagged towards the inside of the
system, and as untagged towards the exterior. The tag encodes the switch
id and the source port index.
This means that cross-chip bridging for dsa_8021q only entails adding
the dsa_8021q pvids of one switch to the RX filter of the other
switches. Everything else falls naturally into place, as long as the
bottom-end of ports (the leaves in the tree) is comprised exclusively of
dsa_8021q-compatible (i.e. sja1105 switches). Otherwise, there would be
a chance that a front-panel switch transmits a packet tagged with a
dsa_8021q header, header which it wouldn't be able to remove, and which
would hence "leak" out.
The only use case I tested (due to lack of board availability) was when
the sja1105 switches are part of disjoint trees (however, this doesn't
change the fact that multiple sja1105 switches still need unique switch
identifiers in such a system). But in principle, even "true" single-tree
setups (with DSA links) should work just as fine, except for a small
change which I can't test: dsa_towards_port should be used instead of
dsa_upstream_port (I made the assumption that the routing port that any
sja1105 should use towards its neighbours is the CPU port. That might
not hold true in other setups).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Somewhat similar to dsa_tree_find, dsa_switch_find returns a dsa_switch
structure pointer by searching for its tree index and switch index (the
parameters from dsa,member). To be used, for example, by drivers who
implement .crosschip_bridge_join and need a reference to the other
switch indicated to by the tree_index and sw_index arguments.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 8db0a2ee2c ("net: bridge: reject DSA-enabled master netdevices
as bridge members") added a special check in br_if.c in order to check
for a DSA master network device with a tagging protocol configured. This
was done because back then, such devices, once enslaved in a bridge
would become inoperative and would not pass DSA tagged traffic anymore
due to br_handle_frame returning RX_HANDLER_CONSUMED.
But right now we have valid use cases which do require bridging of DSA
masters. One such example is when the DSA master ports are DSA switch
ports themselves (in a disjoint tree setup). This should be completely
equivalent, functionally speaking, from having multiple DSA switches
hanging off of the ports of a switchdev driver. So we should allow the
enslaving of DSA tagged master network devices.
Instead of the regular br_handle_frame(), install a new function
br_handle_frame_dummy() on these DSA masters, which returns
RX_HANDLER_PASS in order to call into the DSA specific tagging protocol
handlers, and lift the restriction from br_add_if.
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Huazhong Tan says:
====================
net: hns3: misc updates for -next
This patchset includes some misc updates for the HNS3 ethernet driver.
#1 & #2 add two cleanups.
#3 provides an interface for the client to query the CMDQ's status.
#4 adds a little optimization about debugfs.
#5 prevents 1000M auto-negotiation off setting.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 802.3 specification does not specify the behavior of
auto-negotiation off with 1000M in PHY. Therefore, some PHY
compatibility issues occur. This patch forbids the setting of
this unreasonable mode by ethtool in driver.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch optimizes the judgment of the input parameters of dump ncl
config by checking the number and value of the input parameters apart.
It's clearer and more reasonable.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch provides a new interface for the client to query
whether CMDQ is ready to work.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the UM, command 0x0B03 and 0x0B13 are used to
query the statistics about TX and RX, not the status, so
modifies the unsuitable macro name of these two command.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
HCLGE_MISC_VECTOR_INT_STS and HCLGE_VECTOR_PF_OTHER_INT_STS_REG
both represent the misc interrupt status register(0x20800), so
removes HCLGE_VECTOR_PF_OTHER_INT_STS_REG and replaces it with
HCLGE_MISC_VECTOR_INT_STS.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn says:
====================
Ethernet Cable test support
any copper Ethernet PHY have support for performing diagnostics of
the cable. Are the cable shorted, broken, not plugged into anything at
the other end? And they can report roughly how far along the cable any
fault is.
Add infrastructure in ethtool and phylib support for triggering a
cable test and reporting the results. The Marvell 1G PHY driver is
then extended to make use of this infrastructure.
For testing, a modified ethtool(1) can be found here:
https://github.com/lunn/ethtool.git feature/cable-test-v4. This also
contains extra code for TDR dump, which will be added to the kernel in
a later patch series.
Thanks to Chris Healy for extensive testing.
v2:
See individual patches but:
Remove _REPLY messages
Change length into a u32
Grammar fixes
Rename functions for consistency
Extack for cable test already running
Remove ethnl_cable_test_act_ops
Add status attributes
Rename pairs from numbers to letters
v3:
See individual patches but:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Fixed example in document
Add ETHTOOL_A_CABLE_NEST_* enum
Add ETHTOOL_MSG_CABLE_TEST_NTF to documentation
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
s/mavell/marvell/g
Remove include of <uapi/linux/ethtool_netlink.h>
EMSGSIZE when ethnl_bcastmsg_put() fails
Print an error message on failure, since this is a void function.
v4:
See individual patches but:
Remove unwanted blank line
ENOTSUPP->EOPNOTSUPP
Move EINVAL->EMSGSIZE fix to correct patch
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Given that it takes time to run a cable test, send a notify message at
the start, as well as when it is completed.
v3:
EMSGSIZE when ethnl_bcastmsg_put() fails
Print an error message on failure, since this is a void function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since running a cable test is disruptive, put the interface into
operative state testing while the test is running.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Marvell PHYs have a couple of different register sets for
performing cable tests. Page 7 provides the simplest to use.
v3:
s/mavell/marvell/g
Remove include of <uapi/linux/ethtool_netlink.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHY drivers can use these helpers for reporting the results. The
results get translated into netlink attributes which are added to the
pre-allocated skbuf.
v3:
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
v4:
s/ENOTSUPP/EOPNOTSUPP/g
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make some helpers for building ethtool netlink messages available
outside the compilation unit, so they can be used for building
messages which are not simple get/set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the attributes needed to report cable test results to userspace.
The reports are expected to be per twisted pair. A nested property per
pair can report the result of the cable test. A nested property can
also report the length of the cable to any fault.
v2:
Grammar fixes
Change length from u16 to u32
s/DEV/HEADER/g
Add status attributes
Rename pairs from numbers to letters.
v3:
Fixed example in document
Add ETHTOOL_A_CABLE_NEST_* enum
Add ETHTOOL_MSG_CABLE_TEST_NTF to documentation
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new ethtool netlink calls to trigger the starting of a PHY cable
test.
Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when
ETHTOOL_NETLINK is builtin, which would result in kernel linking errors.
v2:
Remove unwanted white space change
Remove ethnl_cable_test_act_ops and use doit handler
Rename cable_test_set_policy cable_test_act_policy
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY
v3:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Add Reviewed-by tags
v4:
Remove unwanted blank line
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHYs are not capable of generating interrupts when a cable test
finished. They do however support interrupts for normal operations,
like link up/down. As such, the PHY state machine would normally not
poll the PHY.
Add support for indicating the PHY state machine must poll the PHY
when performing a cable test.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Running a cable test is desruptive to normal operation of the PHY and
can take a 5 to 10 seconds to complete. The RTNL lock cannot be held
for this amount of time, and add a new state to the state machine for
running a cable test.
The driver is expected to implement two functions. The first is used
to start a cable test. Once the test has started, it should return.
The second function is called once per second, or on interrupt to
check if the cable test is complete, and to allow the PHY to report
the status.
v2:
Rename phy_cable_test_abort to phy_abort_cable_test
Return different extack when already running test
Use phy_init_hw() to reset the PHY
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable status is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the current codes, the octeontx2 uses its own method to allocate
the pool buffers, but there are some issues in this implementation.
1. We have to run the otx2_get_page() for each allocation cycle and
this is pretty error prone. As I can see there is no invocation
of the otx2_get_page() in otx2_pool_refill_task(), this will leave
the allocated pages have the wrong refcount and may be freed wrongly.
2. It wastes memory. For example, if we only receive one packet in a
NAPI RX cycle, and then allocate a 2K buffer with otx2_alloc_rbuf()
to refill the pool buffers and leave the remain area of the allocated
page wasted. On a kernel with 64K page, 62K area is wasted.
IMHO it is really unnecessary to implement our own method for the
buffers allocate, we can reuse the napi_alloc_frag() to simplify
our code.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
mlxsw: spectrum: Enforce some HW limitations for matchall TC offload
Jiri says:
There are some limitations for TC matchall classifier offload that are
given by the mlxsw HW dataplane. It is not possible to do sampling on
egress and also the mirror/sample vs. ACL (flower) ordering is fixed. So
check this and forbid to offload incorrect setup.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that the drive restricts incorrect order of inserted matchall
vs. flower rules.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check that matchall rules with sample actions are not possible to be
inserted to egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The file is about to contain matchall restrictions too, so change the
name to make it more generic.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On ingress, the matchall rules doing mirroring and sampling are offloaded
into hardware blocks that are processed before any flower rules.
On egress, the matchall mirroring rules are offloaded into hardware
block that is processed after all flower rules.
Therefore check the priorities of inserted flower rules against
existing matchall rules and ensure the correct ordering.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On ingress, the matchall rules doing mirroring and sampling are offloaded
into hardware blocks that are processed before any flower rules.
On egress, the matchall mirroring rules are offloaded into hardware
block that is processed after all flower rules.
Therefore check the priorities of inserted matchall rules against
existing flower rules and ensure the correct ordering.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce an infrastructure that allows to get minimum and maximum
rule priority for specified chain. This is going to be used by
a subsequent patch to enforce ordering between flower and
matchall filters.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As there are going to be other matchall specific fields in flow
structure, put the existing list field into matchall substruct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce an infrastructure that allows to get minimum and maximum
rule priority for specified chain. This is going to be used by
a subsequent patch to enforce ordering between flower and
matchall filters.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
HW supports packet sampling on ingress only. Check and fail if user
is adding sample on egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
adds ndo_set_vf_rate/ndo_set_vf_spoofchk/ndo_set_vf_link_state
to configure netdev of virtual function
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This series includes updates to mlx5 netdev driver and bonding updates
to support getting the next active tx slave.
1) merge commit with mlx5-next that includes bonding updates from Maor
Bonding: Add support to get xmit slave
2) Maxim makes some general code improvements to TX data path
3) Tariq makes some general code improvements to kTLS and mlx5 accel layer
in preparation for mlx5 TLS RX.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl62ZFYACgkQSD+KveBX
+j7lMQgAi5KMceqekMRec1JzXHFOxJ8IIUzLVNW7dQt+2WKNZBTsY0nFo6dVa1NY
zwbd64VtBG9mojC51CNNY3+KlkC5NWjszkEYIAnektGP1vcLtcoq/t1C9XIEroS5
thWoA3/KsUg0Ocm3ilhdbaZMle2PXzPO7mo6UBt9WadE21rNB6h8TN05Mton+a+M
W3WlCC9UuwCA5NH7DwqiVYxwM+3P/8n1iXXcfR41oggA1eGPf4pUrR2MhAtvuK5k
4scdtUnBqvSomZwO0jadp4+XG8H3gLPyqToH1uK49QQbpD6gF7+eRuYvVttutfVk
/df41bz1JTHnCQ1wSTxviHQS356TJQ==
=ThX8
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-05-09
This series includes updates to mlx5 netdev driver and bonding updates
to support getting the next active tx slave.
1) merge commit with mlx5-next that includes bonding updates from Maor
Bonding: Add support to get xmit slave
2) Maxim makes some general code improvements to TX data path
3) Tariq makes some general code improvements to kTLS and mlx5 accel layer
in preparation for mlx5 TLS RX.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
