It can move all pullup/pulldown operation control to udc-core
through usb_gadget_connect/usb_gadget_disconnect according to
vbus status.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit updates udc core vbus status, and try to connect
or disconnect gadget.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of iterate to find usb_udc according to usb_gadget, this
way is easier.
Alan Stern suggests this way too:
http://marc.info/?l=linux-usb&m=142168496528894&w=2
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the HCD is disconnected, the DMA transfers still in-flight were cleaned-up
but the count of available DMA channels (e.g. available_host_channels) was not
reset.
The pool of DMA channels can be depleted when doing unclean
disconnection of USB peripherals, and reaches the point where no
transfer was possible until the next reboot/reload of the driver.
Tested by putting a programmable USB mux on the port and randomly
plugging/unpluging a USB HUB with USB mass-storage key, USB-audio and
USB-ethernet dongle connected to its downstream ports, and also doing the
disconnection early while the devices are still enumerating to get more URBs
in-flight.
After the patch, the devices are still enumerating after thousands of cycles,
while the port was totally dead before.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code is no longer used now that mach-msm has been removed.
Delete it.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some Renesas SoCs have the USB-DMAC. It is able to terminate transfers
when a short packet is received, even if less bytes than the transfer
counter size have been received. Also, it is able to send a short
packet even if the packet size is not multiples of 8bytes.
Since the previous code has used the interruption of USBHS controller
when receiving packets even if this driver has used a dmac, a lot of
interruptions has happened. This patch will reduce such interruptions.
This patch allows to use the USB-DMAC on R-Car H2 and M2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the setup sequence in xfer_work(). Otherwise,
sometimes a usb transaction will get stuck.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To connect the channel of USB-DMAC to USBHS DnFIFO number, this patch
adds this channel/FIFO number in dma-names. Otherwise, this driver
needs to add analysis code for device tree.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB_DIR_OUT happens to be zero, so the result of bitwise and is always 0.
Consequently, break will never happen in the SOFT_RESET case.
This patch uses a compatible condition with a non-zero USB_DIR_IN,
which might or might not evaluate to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was a missing goto so we free "opts" and then dereference it.
Fixes: ee1cd515e8 ('usb: gadget: printer: add configfs support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"num" is a u16 so it can't go higher than 65535. kstrtou16() has a
range check built in so this is already handled.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2-pci driver requires the generic PHY. This fixes undefined
reference issues when it is not selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use %ps for actual addresses, otherwise you'll get bad output
on arches like ppc64 where %pf expects a function descriptor
(which is not what __builtin_return_address returns).
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: linux-usb@vger.kernel.org
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If device is configured to work only in HOST or DEVICE mode, there is
no point in initializing both subdrivers. This patch also fixes
resource leakage if host subdriver fails to initialize.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pci driver now registers a platform driver, like in dwc3, and lets
its probe function do all the initialization. This allows it to
account for changes to the platform driver that were not added to the
pci driver. Also future changes to the probe function don't have to be
duplicated. This also has the effect of adding device and DRD mode to
the pci driver. Tested on the Synopsys HAPS PCIe platform.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc is then checked for NULL, if NULL, it is then dereferenced as
udc->dev, it is found using Coccinelle.
We simplify the code to fix this problem, and we delete some conditions
at if {} which will never be met.
Reported-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Reported-by : Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
connect AR9271(USB wifi) to AM335x, and send a flood ping from Mac OSX,
AR9271 is stopped.
on USB bus, the following occurs.
- OUT transaction is ACKed (NYET).
- IN transaction is ACKed (512bytes).
- PING-NAK transaction is continued for about 2 seconds (AR9271 timeout?).
In current imprementation, IN-transaction is not completed because it
checks the empty of TX-FIFO in cppi41_dma_callback().
As a result, communication to AR9271 stops.
This patch modified to check the empty of TX-FIFO only when OUT-transaction.
Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 9eb0797722 ("usb: phy: generic: fix the gpios to be optional")
calls gpiod_direction_output() in the probe function, so there is no need to
call it again, as we can simply call gpiod_set_value() directly.
Also, in usb_gen_phy_shutdown() we can simply put the GPIO directly in its
active level state and this allows us to simplify the nop_reset function to
treat only the reset case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function usb_ep_disable() causes completion of all requests queued
for given endpoint, so there is no need to dequeue them after endpoint
disabling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not everybody uses a utf8 locale (unfortunately), so let's avoid
non-ascii characters in the kernel log. Replace the 3-byte utf8
sequence with a 3-byte ascii equivalent.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch add suspend/resume with wakeup support for Atmel USBA.
On suspend: We stay continuously clocked if Vbus signal is not
available. If Vbus signal is available we set the Vbus signal as a wake
up source then we stop the USBA itself and all clocks used by USBA.
On resume: We recover clocks and USBA if we stopped them. If a device is
currently connected at resume time we enable the controller.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB PLL is not necessary for other USB drivers (e.g. OHCI and EHCI)
we will reduce power consumption by switching off the USB PLL if no USB
Host is currently connected to this USB Device.
We are using Vbus GPIO signal to detect Host presence. If Vbus signal is
not available then the device stays continuously clocked.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Vbus IRQ handler needs a started UDC driver to work because it uses
udc->driver, which is set by the UDC start handler. The previous way
chosen was to return from interrupt if udc->driver is NULL using a
spinlock around the check.
We now request an auto disabled (IRQ_NOAUTOEN) Vbus signal IRQ instead
of an auto enabled IRQ followed by disable_irq(). This way we remove the
very small timeslot of enabled IRQ which existed previously between
request() and disable(). We don't need anymore to check if udc->driver
is NULL in IRQ handler.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If vbus gpio is high at init, we should set vbus_prev to true
accordingly to the current vbus state. Without that, we skip the first
vbus interrupt because the saved vbus state is not consistent.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixed a comment typo in drivers/usb/phy/phy-ab8500-usb.c
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
replace numeric value with TYPE_NO_LUN (defined in <scsi/scsi.h>)
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fix some spelling typo found in gadget.xml.
It is because this file is generated from comments in sources,
I had to fix comments in the source, instead of xml file itself.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we pass our own of_node to musb_core, at least
pinctrl settings will be duplicated, meaning that
pinctrl framework will try to select default pin
state for musb_core when they were already requested
by musb-dsps.
A Warning will be printed however things will still
work.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for configfs interface so that f_printer can be used as a
component of usb gadgets composed with it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Substitute some boilerplate code with a dedicated macro.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old interface users left, so it can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The goal is to remove the old function interface, so its (only) user
must be converted to the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add configfs support, a usb function must be converted to use
the new interface. This patch converts the function to the new interface
and provides backward compatiblity layer, which can be removed after
all its users are converted to use the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The legacy printer gadget now contains both a reusable printer function
and legacy gadget proper implementations interwoven, but logically
separate. This patch factors out a reusable f_printer.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With all the obstacles removed it is possible to allow more than one
instance of the printer function. Since the function requires allocating
character device region, a maximum number of allowed instances is defined.
Such an approach is used in f_acm and in f_hid.
With multiple instances it does not make sense to depend on a
lock_printer_io member of a dynamically allocated (and destroyed) struct
printer_dev to clean up after all instances of the printer function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Verify that a given usb_ctrlrequest is meant for printer function.
The following parts of the request are tested:
- bmRequestType:Data transfer direction
- bmRequestType:Type
- bmRequestType:Recipient
- bRequest
- wValue for bRequest 1 and 2
- wLength
Additionally, the request is considered meant for this function
iff the decoded interface number matches dev->interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Non-standard requests can encode the actual interface number in a
non-standard way. For example composite_setup() assumes
that it is w_index && 0xFF, but the printer function encodes the interface
number in a context-dependet way (either w_index or w_index >> 8).
This can lead to such requests being directed to wrong functions.
This patch adds req_match() method to usb_function. Its purpose is to
verify that a given request can be handled by a given function.
If any function within a configuration provides the method and it returns
true, then it is assumed that the right function is found.
If a function uses req_match(), it should try as hard as possible to
determine if the request is meant for it.
If no functions in a configuration provide req_match or none of them
returns true, then fall back to the usual approach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
5 uses of container_of() in the same context justify wrapping it
in a static inline function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The printer_dev can be recovered from printer_func_unbind() function's
parameters.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The mutex is a legacy after semi-automatic Big Kernel Lock removal.
printer_open() does its own locking, so no need to duplicate it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Call gprinter_setup() from gadget's bind instead of module's init.
Call gprinter_cleaup() corerspondingly. This detaches printer function's
logic from legacy printer gadget's implementation.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Factor out gprinter_setup() and gprinter_cleanup() so that it is
easy to change the place they are called from.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer, the function's code should
not use file global variables related to legacy printer gadget's
implementation.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer.c, the code related to the
function should be placed in functions related to the function.
printer_cfg_unbind() becomes empty, so it is removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conversion to the new function interface requires splitting a
<something>_bind_config() function into two parts: allocation of
container_of struct usb_function and invocation of usb_add_function().
This patch moves the latter to the end of the f_printer_bind_config()
in order to enable conversion to the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer.c, the code related to the
function should be placed in functions related to the function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
