John Fastabend says:
====================
l2 hardware accelerated macvlans
This patch adds support to offload macvlan net_devices to the
hardware. With these patches packets are pushed to the macvlan
net_device directly and do not pass through the lower dev.
The patches here have made it through multiple iterations
each with a slightly different focus. First I tried to
push these as a new link type called "VMDQ". The patches
shown here,
http://comments.gmane.org/gmane.linux.network/237617
Following this implementation I renamed the link type
"VSI" and addressed various comments. Finally Neil
Horman picked up the patches and integrated the offload
into the macvlan code. Here,
http://permalink.gmane.org/gmane.linux.network/285658
The attached series is clean-up of his patches, with a
few fixes.
If folks find this series acceptable there are a few
items we can work on next. First broadcast and multicast
will use the hardware even for local traffic with this
series. It would be best (I think) to use the software
path for macvlan to macvlan traffic and save the PCIe
bus. This depends on how much you value CPU time vs
PCIE bandwidth. This will need another patch series
to flush out.
Also this series only allows for layer 2 mac forwarding
where some hardware supports more interesting forwarding
capabilities. Integrating with OVS may be useful here.
As always any comments/feedback welcome.
My basic I/O test is here but I've also done some link
testing, SRIOV/DCB with macvlans and others,
Changelog:
v2: two fixes to ixgbe when all features DCB, FCoE, SR-IOV
are enabled with macvlans. A VMDQ_P() reference
should have been accel->pool and do not set the offset
of the ring index from dfwd add call. The offset is used
by SR-IOV so clearing it can cause SR-IOV quue index's
to go sideways. With these fixes testing macvlan's with
SRIOV enabled was successful.
v3: addressed Neil's comments in ixgbe
fixed error path on dfwd_add_station() in ixgbe
fixed ixgbe to allow SRIOV and accelerated macvlans to
coexist.
v4: Dave caught some strange indentation, fixed it here
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that l2 acceleration ops are in place from the prior patch,
enable ixgbe to take advantage of these operations. Allow it to
allocate queues for a macvlan so that when we transmit a frame,
we can do the switching in hardware inside the ixgbe card, rather
than in software.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a operations structure that allows a network interface to export
the fact that it supports package forwarding in hardware between
physical interfaces and other mac layer devices assigned to it (such
as macvlans). This operaions structure can be used by virtual mac
devices to bypass software switching so that forwarding can be done
in hardware more efficiently.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
timecounter_init() was was called only after first potential
timecounter_read().
Moved mlx4_en_init_timestamp() before mlx4_en_init_netdev()
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"card2" is NULL here so I have changed it to use "id2" instead of
"card2->interface.id".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in cpsw_probe() where we do:
ndev->irq = platform_get_irq(pdev, 0);
if (ndev->irq < 0) {
The problem is that "ndev->irq" is unsigned so the error handling
doesn't work. I have changed it to a regular int.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently added a new error path and it needs a dev_put().
Fixes: 7adac1ec81 ('6lowpan: Only make 6lowpan links to IEEE802154 devices')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On top of commit 366cddb40 "IB/rdma_cm: TOS <=> UP mapping for IBoE", add
support for case vlan egress map is used.
When the IBoE session is being set over a vlan, inherit the socket priority
to vlan priority mapping which was configured for the vlan device egress map.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a method for read-only access to the vlan device egress mapping.
Do this by refactoring vlan_dev_get_egress_qos_mask() such that now it
receives as an argument the skb priority instead of pointer to the skb.
Such an access is needed for the IBoE stack where the control plane
goes through the network stack. This is an add-on step on top of commit
d4a968658c "net/route: export symbol ip_tos2prio" which allowed the RDMA-CM
to use ip_tos2prio.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If build_skb fails the memory associated with the ring buffer is freed but
the ri->data member is not zeroed in this case. This causes a double-free
of this memory in tg3_free_rings->... path. The patch moves this block after
setting ri->data to NULL.
It would be nice to fix this bug also in stable >= v3.4 trees.
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior will take over the bnx2x maintenance.
It's been a pleasure!
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne says:
====================
tipc: message reassembly using fragment chain
We introduce a new reassembly algorithm that improves performance
and eliminates the risk of causing out-of-memory situations.
v3: -Use skb_try_coalesce, and revert to fraglist if this does not succeed.
-Make sure reassembly list head is uncloned.
v2: -Rebased on Ying's indentation fix.
-Node unlock call in msg_fragmenter case moved from patch #2 to #1.
('continue' with this lock held would cause spinlock recursion if only
patch #1 is used)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If appending a received fragment to the pending fragment chain
in a unicast link fails, the current code tries to force a retransmission
of the fragment by decrementing the 'next received sequence number'
field in the link. This is done under the assumption that the failure
is caused by an out-of-memory situation, an assumption that does
not hold true after the previous patch in this series.
A failure to append a fragment can now only be caused by a protocol
violation by the sending peer, and it must hence be assumed that it
is either malicious or buggy. Either way, the correct behavior is now
to reset the link instead of trying to revert its sequence number.
So, this is what we do in this commit.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first fragment of a long data data message is received on a link, a
reassembly buffer large enough to hold the data from this and all subsequent
fragments of the message is allocated. The payload of each new fragment is
copied into this buffer upon arrival. When the last fragment is received, the
reassembled message is delivered upwards to the port/socket layer.
Not only is this an inefficient approach, but it may also cause bursts of
reassembly failures in low memory situations. since we may fail to allocate
the necessary large buffer in the first place. Furthermore, after 100 subsequent
such failures the link will be reset, something that in reality aggravates the
situation.
To remedy this problem, this patch introduces a different approach. Instead of
allocating a big reassembly buffer, we now append the arriving fragments
to a reassembly chain on the link, and deliver the whole chain up to the
socket layer once the last fragment has been received. This is safe because
the retransmission layer of a TIPC link always delivers packets in strict
uninterrupted order, to the reassembly layer as to all other upper layers.
Hence there can never be more than one fragment chain pending reassembly at
any given time in a link, and we can trust (but still verify) that the
fragments will be chained up in the correct order.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message fragment is received in a broadcast or unicast link,
the reception code will append the fragment payload to a big reassembly
buffer through a call to the function tipc_recv_fragm(). However, after
the return of that call, the logics goes on and passes the fragment
buffer to the function tipc_net_route_msg(), which will simply drop it.
This behavior is a remnant from the now obsolete multi-cluster
functionality, and has no relevance in the current code base.
Although currently harmless, this unnecessary call would be fatal
after applying the next patch in this series, which introduces
a completely new reassembly algorithm. So we change the code to
eliminate the redundant call.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
This patch adds an MDIO driver which handles the MII bus.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new documentation for the packets_per_slave option available
for balance-rr mode.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to extend round-robin mode with a new option called
packets_per_slave which can have the following values and effects:
0 - choose a random slave
1 (default) - standard round-robin, 1 packet per slave
>1 - round-robin when >1 packets have been transmitted per slave
The allowed values are between 0 and 65535.
This patch also fixes the comment style in bond_xmit_roundrobin().
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check user-defined length in snmp ioctl request and allow request
only if it fits into a qeth command buffer.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just an unnecessary semicolon that should be removed...
Whitespace neatening of macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more standard logging style.
Convert smsc_<level> macros to use netif_<level>.
Remove unused #define PFX
Add pr_fmt and neaten pr_<level> uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to use a percpu structure vq_index to record the cpu to queue
mapping, this is suboptimal since it duplicates the work of XPS and
loses all other XPS functionality such as allowing user to configure
their own transmission steering strategy.
So this patch switches to use XPS and suggest a default mapping when
the number of cpus is equal to the number of queues. With XPS support,
there's no need for keeping per-cpu vq_index and .ndo_select_queue(),
so they were removed also.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now rt6_alloc_cow() is only called by ip6_pol_route() when
rt->rt6i_flags doesn't contain both RTF_NONEXTHOP and RTF_GATEWAY,
and rt->rt6i_flags hasn't been changed in ip6_rt_copy().
So there is no neccessary to judge whether rt->rt6i_flags contains
RTF_GATEWAY or not.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1e2bd517c1 ("udp6: Fix udp
fragmentation for tunnel traffic.") changed the calculation if
there is enough space to include a fragment header in the skb from a
skb->mac_header dervived one to skb_headroom. Because we already peeled
off the skb to transport_header this is wrong. Change this back to check
if we have enough room before the mac_header.
This fixes a panic Saran Neti reported. He used the tbf scheduler which
skb_gso_segments the skb. The offsets get negative and we panic in memcpy
because the skb was erroneously not expanded at the head.
Reported-by: Saran Neti <Saran.Neti@telus.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cc9d4598 'net: mv643xx_eth: use of_phy_connect if phy_node
present' made the call to phy_scan optional, if the DT has a link to
the phy node.
However phy_scan has the side effect of calling phy_addr_set, which
writes the phy MDIO address to the ethernet controller. If phy_addr_set
is not called, and the bootloader has not set the correct address then
the driver will fail to function.
Tested on Kirkwood.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sockets marked with IP_PMTUDISC_INTERFACE won't do path mtu discovery,
their sockets won't accept and install new path mtu information and they
will always use the interface mtu for outgoing packets. It is guaranteed
that the packet is not fragmented locally. But we won't set the DF-Flag
on the outgoing frames.
Florian Weimer had the idea to use this flag to ensure DNS servers are
never generating outgoing fragments. They may well be fragmented on the
path, but the server never stores or usees path mtu values, which could
well be forged in an attack.
(The root of the problem with path MTU discovery is that there is
no reliable way to authenticate ICMP Fragmentation Needed But DF Set
messages because they are sent from intermediate routers with their
source addresses, and the IMCP payload will not always contain sufficient
information to identify a flow.)
Recent research in the DNS community showed that it is possible to
implement an attack where DNS cache poisoning is feasible by spoofing
fragments. This work was done by Amir Herzberg and Haya Shulman:
<https://sites.google.com/site/hayashulman/files/fragmentation-poisoning.pdf>
This issue was previously discussed among the DNS community, e.g.
<http://www.ietf.org/mail-archive/web/dnsext/current/msg01204.html>,
without leading to fixes.
This patch depends on the patch "ipv4: fix DO and PROBE pmtu mode
regarding local fragmentation with UFO/CORK" for the enforcement of the
non-fragmentable checks. If other users than ip_append_page/data should
use this semantic too, we have to add a new flag to IPCB(skb)->flags to
suppress local fragmentation and check for this in ip_finish_output.
Many thanks to Florian Weimer for the idea and feedback while implementing
this patch.
Cc: David S. Miller <davem@davemloft.net>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork says:
====================
The huawei_cdc_ncm driver.
Enrico has been kind enough to let me repost his driver with the changes
requested by Oliver Neukum during the last review of this series.
The changes I have made from Enricos original v5 series to this version
are:
v6:
- fix to avoid corrupting drvstate->pmcount
- fix error return value from huawei_cdc_ncm_suspend()
- drop redundant testing for subdriver->suspend during resume
- broke a few lines to keep within the 80 columns recommendation
- rebased on top of current net-next
Enrico's orginal introduction to the v5 series follows below. It explains
the background much better than I can.
Bjørn
[quote Enrico Mioso]
So this is a new, revised, edition of the huawei_cdc_ncm.c driver, which
supports devices resembling the NCM standard, but using it also as a mean
to encapsulate other protocols, as is the case for the Huawei E3131 and
E3251 modem devices.
Some precisations are needed however - and I encourage discussion on this: and
that's why I'm sending this message with a broader CC.
Merging those patches might change:
- the way Modem Manager interacts with those devices
- some regressions might be possible if there are some unknown firmware
variants around (Franko?)
First of all: I observed the behaviours of two devices.
Huawei E3131: this device doesn't accept NDIS setup requests unless they're
sent via the embedded AT channel exposed by this driver.
So actually we gain funcionality in this case!
The second case, is the Huawei E3251: which works with standard NCM driver,
still exposing an AT embedded channel. Whith this patch set applied, you gain
some funcionality, loosing the ability to catch standard NCM events for now.
The device will work in both ways with no problems, but this has to be
acknowledged and discussed. Might be we can develop this driver further to
change this, when more devices are tested.
We where thinking Huawei changed their interfaces on new devices - but probably
this driver only works around a nice firmware bug present in E3131, which
prevented the modem from being used in NDIS mode.
I think committing this is definitely wortth-while, since it will allow for
more Huawei devices to be used without serial connection. Some devices like the
E3251 also, reports some status information only via the embedded AT channel,
at least in my case.
Note: I'm not subscribed to any list except the Modem Manager's one, so please
CC me, thanks!!
[/quote]
Enrico Mioso (3):
net: cdc_ncm: Export cdc_ncm_{tx,rx}_fixup functions for re-use
net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver
net: cdc_ncm: remove non-standard NCM device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove device IDs of NCM-like (but not NCM-conformant) devices, that are
handled by the huawwei_cdc_ncm driver now.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports devices using the NCM protocol as an encapsulation layer
for other protocols, like the E3131 Huawei 3G modem. This drivers approach was
heavily inspired by the qmi_wwan/cdc_mbim approach & code model.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers implementing NCM-like protocols, may re-use those functions, as is
the case in the huawei_cdc_ncm driver.
Export them via EXPORT_SYMBOL_GPL, in accordance with how other functions have
been exported.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code of flow label in Linux Kernel follows
the rules of RFC 1809 (an informational one) for
conditions on flow label sharing. There rules are
not in the last proposed standard for flow label
(RFC 6437), or in the previous one (RFC 3697).
Since this code does not follow any current or
old standard, we can remove it.
With this removal, the ipv6_opt_cmp function is
now a dead code and it can be removed too.
Changelog to v1:
* add justification for the change
* remove the condition on IPv6 options
[ Remove ipv6_hdr_cmp and it is now unused as well. -DaveM ]
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please accept the following pull request intended for the 3.13 tree...
I had intended to pass most of these to you as much as two weeks ago.
Unfortunately, I failed to account for the effects of bad Internet
connections and my own fatique/laziness while traveling. On the bright
side, at least these have been baking in linux-next for some time!
For the mac80211 bits, Johannes says:
"This time I have two fixes for P2P (which requires not using CCK rates)
and a workaround for APs with broken WMM information."
For the iwlwifi bits, Johannes says:
"I have a few fixes for warnings/issues: one from Alex, fixing scan
timings, one from Emmanuel fixing a WARN_ON in the DVM driver, one from
Stanislaw removing a trigger-happy WARN_ON in the MVM driver and a
change from myself to try to recover when the device isn't processing
commands quickly."
And:
"For this round, I have a lot of changes:
* power management improvements
* BT coexistence improvements/updates
* new device support
* VHT support
* IBSS support (though due to a small bug it requires new firmware)
* various other fixes/improvements."
For the Bluetooth bits, Gustavo says:
"More patches for 3.12, busy times for Bluetooth. More than a 100 commits since
the last pull. The bulk of work comes from Johan and Marcel, they are doing
fixes and improvements all over the Bluetooth subsystem, as the diffstat can
show."
For the ath10k and ath6kl bits, Kalle says:
"Bartosz added support to ath10k for our 10.x AP firmware branch, which
gives us AP specific features and fixes. We still support the main
firmware branch as well just like before, ath10k detects runtime what
firmware is used. Unfortunately the firmware interface in 10.x branch is
somewhat different so there was quite a lot of changes in ath10k for
this.
Michal and Sujith did some performance improvements in ath10k. Vladimir
fixed a compiler warning and Fengguang removed an extra semicolon."
For the NFC bits, Samuel says:
"It's a fairly big one, with the following highlights:
- NFC digital layer implementation: Most NFC chipsets implement the NFC
digital layer in firmware, but others have more basic functionalities
and expect the host to implement the digital layer. This layer sits
below the NFC core.
- Sony's port100 support: This is "soft" NFC USB dongle that expects the
digital layer to be implemented on the host. This is the first user of
our NFC digital stack implementation.
- Secure element API: We now provide a netlink API for enabling,
disabling and discovering NFC attached (embedded or UICC ones) secure
elements. With some userspace help, this allows us to support NFC
payments.
Only the pn544 driver currently supports that API.
- NCI SPI fixes and improvements: In order to support NCI devices over
SPI, we fixed and improved our NCI/SPI implementation. The currently
most deployed NFC NCI chipset, Broadcom's bcm2079x, supports that mode
and we're planning to use our NCI/SPI framework to implement a
driver for it.
- pn533 fragmentation support in target mode: This was the only missing
feature from our pn533 impementation. We now support fragmentation in
both Tx and Rx modes, in target mode."
On top of all that, brcmfmac and rt2x00 both get the usual flurry
of updates. A few other drivers get hit here or there as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2613af0ed1 (virtio_net: migrate mergeable
rx buffers to page frag allocators) try to increase the payload/truesize for
MTU-sized traffic. But this will introduce the extra overhead for GSO packets
received because of the frag list. This commit tries to reduce this issue by
coalesce the possible rx frags when possible during rx. Test result shows the
about 15% improvement on full size GSO packet receiving (and even better than
before commit 2613af0ed1).
Before this commit:
./netperf -H 192.168.100.4
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.100.4
() port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 20303.87
After this commit:
./netperf -H 192.168.100.4
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.100.4
() port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 23841.26
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael Dalton <mwdalton@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we need to coalesce the rx frags to avoid frag list. One example is
virtio-net driver which tries to use small frags for both MTU sized packet and
GSO packet. So this patch introduce skb_coalesce_rx_frag() to do this.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael Dalton <mwdalton@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial patch converting ERR_PTR(PTR_ERR()) into ERR_CAST().
No functional changes.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As described in commit 5a581b367 (jiffies: Avoid undefined
behavior from signed overflow), according to the C standard
3.4.3p3, overflow of a signed integer results in undefined
behavior.
To fix this, do as the above commit, and do an unsigned
subtraction, and interpreting the result as a signed
two's-complement number. This is based on the theory from
RFC 1982 and is nicely described in wikipedia here:
https://en.wikipedia.org/wiki/Serial_number_arithmetic#General_Solution
A side-note, I have seen practical issues with the previous logic
when dealing with 16-bit, on a 64-bit machine (gcc version
4.4.5). This were 32-bit, which I have not observed issues with.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jesper Dangaard Brouer <netoptimizer@brouer.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here's a pull request for net-next.
It includes a patch by Oliver Hartkopp et al. that adds documentation
for the broadcast manager to Documentation/networking/can.txt. Three
patches by me that clean up the netlink handling code in the CAN core.
And another patch that removes a not needed function from the ti_hecc
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow start now increases cwnd by 1 if an ACK acknowledges some packets,
regardless the number of packets. Consequently slow start performance
is highly dependent on the degree of the stretch ACKs caused by
receiver or network ACK compression mechanisms (e.g., delayed-ACK,
GRO, etc). But slow start algorithm is to send twice the amount of
packets of packets left so it should process a stretch ACK of degree
N as if N ACKs of degree 1, then exits when cwnd exceeds ssthresh. A
follow up patch will use the remainder of the N (if greater than 1)
to adjust cwnd in the congestion avoidance phase.
In addition this patch retires the experimental limited slow start
(LSS) feature. LSS has multiple drawbacks but questionable benefit. The
fractional cwnd increase in LSS requires a loop in slow start even
though it's rarely used. Configuring such an increase step via a global
sysctl on different BDPS seems hard. Finally and most importantly the
slow start overshoot concern is now better covered by the Hybrid slow
start (hystart) enabled by default.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications have started to use Fast Open (e.g., Chrome browser has
such an optional flag) and the feature has gone through several
generations of kernels since 3.7 with many real network tests. It's
time to enable this flag by default for applications to test more
conveniently and extensively.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
This batch contains fives nf_tables patches for your net-next tree,
they are:
* Fix possible use after free in the module removal path of the
x_tables compatibility layer, from Dan Carpenter.
* Add filter chain type for the bridge family, from myself.
* Fix Kconfig dependencies of the nf_tables bridge family with
the core, from myself.
* Fix sparse warnings in nft_nat, from Tomasz Bursztyka.
* Remove duplicated include in the IPv4 family support for nf_tables,
from Wei Yongjun.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
This is another batch containing Netfilter/IPVS updates for your net-next
tree, they are:
* Six patches to make the ipt_CLUSTERIP target support netnamespace,
from Gao feng.
* Two cleanups for the nf_conntrack_acct infrastructure, introducing
a new structure to encapsulate conntrack counters, from Holger
Eitzenberger.
* Fix missing verdict in SCTP support for IPVS, from Daniel Borkmann.
* Skip checksum recalculation in SCTP support for IPVS, also from
Daniel Borkmann.
* Fix behavioural change in xt_socket after IP early demux, from
Florian Westphal.
* Fix bogus large memory allocation in the bitmap port set type in ipset,
from Jozsef Kadlecsik.
* Fix possible compilation issues in the hash netnet set type in ipset,
also from Jozsef Kadlecsik.
* Define constants to identify netlink callback data in ipset dumps,
again from Jozsef Kadlecsik.
* Use sock_gen_put() in xt_socket to replace xt_socket_put_sk,
from Eric Dumazet.
* Improvements for the SH scheduler in IPVS, from Alexander Frolkin.
* Remove extra delay due to unneeded rcu barrier in IPVS net namespace
cleanup path, from Julian Anastasov.
* Save some cycles in ip6t_REJECT by skipping checksum validation in
packets leaving from our stack, from Stanislav Fomichev.
* Fix IPVS_CMD_ATTR_MAX definition in IPVS, larger that required, from
Julian Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use the _safe version of list_for_each_entry() here otherwise
we have a use after free bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jesse Gross says:
====================
Open vSwitch
A set of updates for net-next/3.13. Major changes are:
* Restructure flow handling code to be more logically organized and
easier to read.
* Rehashing of the flow table is moved from a workqueue to flow
installation time. Before, heavy load could block the workqueue for
excessive periods of time.
* Additional debugging information is provided to help diagnose megaflows.
* It's now possible to match on TCP flags.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Mellanox driver updates
This patch set from Jack Morgenstein does the following:
1. Fix MAC/VLAN SRIOV implementation, and add wrapper functions for VLAN allocation
and de-allocation (patches 1-6).
2. Implements resource quotas when running under SRIOV (patches 7-10).
Patch 7 is a small bug fix, and patches 8-10 implement the quotas.
Quotas are implemented per resource type for VFs and the PF, to prevent
any entity from simply grabbing all the resources for itself and leaving
the other entities unable to obtain such resources.
The series is against net-next commit ba48650 "ipv6: remove the unnecessary statement in find_match()"
changes from V0:
- dropped the 1st patch which needs to go to -stable and hence through net,
not net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements resource quota grant decision when resources are requested,
for the following resources: QPs, CQs, SRQs, MPTs, MTTs, vlans, MACs,
and Counters.
When granting a resource, the quota system increases the allocated-count
for that slave.
When the slave later frees the resource, its allocated-count is reduced.
A spinlock is used to protect the integrity of each resource's free-pool counter.
(One slave may be in the process of being granted a resource while another
slave has crashed, initiating cleanup of that slave's resource quotas).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current kernels, the mlx4 driver running on a VM does not
differentiate between max resource numbers for the HCA and
max quotas -- it simply takes the quota values passed to it
as max-resource values.
However, the driver actually requires the VFs to be aware of
the actual number of resources that the HCA was initialized with,
for QPs, CQs, SRQs and MPTs.
For QPs, CQs and SRQs, the reason is that in completion handling
the driver must know which of the 24 bits are the actual resource
number, and which are "padding" bits.
For MPTs, also, the driver assumes knowledge of the number of MPTs
in the system.
The previous commit fixes the quota logic on the VM for the quota values
passed to it by QUERY_FUNC_CAPS.
For QPs, CQs, SRQs, and MPTs, it takes the max resource numbers
from QUERY_HCA (and not QUERY_FUNC_CAPS). The quotas passed
in QUERY_FUNC_CAPS are used to report max resource number values
in the response to ib_query_device.
However, the Hypervisor driver must consider that VMs
may be running previous kernels, and compatibility must be preserved.
To resolve the incompatibility with previous kernels running on VMs,
we deprecated the quota fields in mlx4_QUERY_FUNC_CAP. In the
deprecated fields, we pass the max-resource values from INIT_HCA
The quota fields are moved to a new location, and the current kernel
driver takes the proper values from that location. There is
also a new flag in dword 0, bit 28 of the mlx4_QUERY_FUNC_CAP mailbox;
if this flag is set, the (VM) driver takes the quota values from the
new location.
VMs running previous kernels will work properly, except that the max resource
numbers reported in ib_query_device for these resources will be
too high. The Hypervisor driver will, however, enforce the quotas
for these VMs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
