initializing proc0's frame base, too, using cpu_set_init_frame(). It's
a kludge because that macro is intended to be used only for init, but
does what we want nonetheless.
loading kernel
worm.o: Undefined symbol `_STUNIT' referenced from text segment
I copied the STUNIT definition from the old scsiconf.c into this file to
work around this problem.
if the 'time on a node is 0,..
tell the world it is the same as 'boottime'.
This is becasue 'time' is not set up when we create the nodes,
so we can't set them then.
may not be desired if you're just going to blow the kernel away again later)
and substitute one that tells the user where the new kernel build
directory actually IS, which can at least be argued to be useful information
in all cases.
Reviewed by: davidg
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
Cosmetic changes and paranoia checks:
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
If select() fails, use syslog() to report the error rather than perror().
Check that all our malloc()s succeed. Report malloc() failure in
ypbindproc_setdom_2() to callers.
yplib.c:
Use #defined constants in ypbinderr_string() rather than hard-coded values.
ypbind.c:
Make fewer assumtions about the state of the dom_alive and dom_broadcasting
flags in roc_received().
If select() fails, use syslog() to report the error rather than perror().
Check that all our malloc()s succeed. Report malloc() failure in
ypbindproc_setdom_2() to callers.
yplib.c:
Use #defined constants in ypbinderr_string() rather than hard-coded values.
Added CONTROL device that only does user-ioctl and nothing else;
Added protection so user-ioctl requires write access;
Clean up scsiconf.h a little. It needs more work.
- set TCP_NOPUSH to keep from sending short packets at each write(2) boundary
- set SO_SNDBUF to 64k so we have a reasonable amount of buffer space
- for a regular file in binary mode which is not being restarted and is
. smaller than 16 Meg, use mmap(2) and write(2) the whole file in one big
gulp
In the most common circumstances, this should dramatically reduce the
system-call load from ftpd, since the call to write() will not return until
the entire file has been written, rather than writing just a few K at a time
in a loop.
In the case where ypserv is started with the -dns flag, fall through to
the DNS lookup code only if asked to match a map with the word 'host'
in its name. This prevents failed matches on non-host maps from being
incorrectly handed off to DNS.
the lookup fails. Updated callers to deal with this. Call in_pcblookuphash
instead of in_pcblookup() in in_pcbconnect; this improves performance of
UDP output by about 17% in the standard case.
Remove bogus targets.
Allocate partition letters as follows:
lowest offset "flags & CHUNK_IS_ROOT" gets 'a',
lowest offset "subtype==FS_SWAP" gets 'b'
the rest is allocated in offset order from this sequence "defghab".
This will generally make sense.
Added rules to complain if more than one CHUNK_IS_ROOT or more than one
FS_SWAP per FreeBSD chunk.
Set CHUNK_IS_ROOT on the 'a' partition in Open_Disk.
Run Fixup_Names in Open_Disk.
Correct Makefile so that we build during all: and only install for
make install.
If /etc/sysconfig exists source it to get the flags for restarting
named with. If /etc/sysconfig says no named runs, don't try to start one.
Don't attempt to kill anything if we can not find the named.pid file.
Reviewed by: Nickolay N. Dudorov <nnd@gw.itfs.nsk.su>
