specified directory is not found in the mount list. Before the
MNT_BYFSID changes, unmount(2) used to return ENOENT for a nonexistent
path and EINVAL for a non-mountpoint, but we can no longer distinguish
between these cases. Of the two error codes, EINVAL was more likely
to occur in practice, and it was the only one of the two that was
documented.
Update the manual page to match the current behaviour.
Suggested by: tjr
Reviewed by: tjr
Make this true in the .for loops too. The following fragment,
FOO= foo bar
all:
.for f in ${FOO}
@echo ${f}
.endfor
when run as "make FOO=xxx" should print "xxx". (OpenBSD had
this bug fixed for some time.)
atomically extracts and holds the physical page that is associated with the
given pmap and virtual address. Such a function is needed to make the
memory mapping optimizations used by, for example, pipes and raw disk I/O
MP-safe.
Reviewed by: tegge
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
ia64_count_cpus() and ia64_probe_sapics() called a single function
to do the the actual work. The difference in behaviour was handled
in that function and was further complicated by adding bootverbose
related code. As such, even the simplest of changes was hard to
comprehend.
Untangling has been done by increasing code duplication and using
a more naive style of coding. FWIW, the object file is slightly
smaller than before, so things aren't as bad as it may seem.
Triggered by: a simple fix on the P4 branch that never got merged.
from the SAB82532 and the Z8530 hardware drivers by introducing
uart_cpu_busaddr(). The assumption is not true on pc98 where
bus_space_handle_t is a pointer to a structure.
The uart_cpu_busaddr() function will return the bus address
corresponding the tag and handle given to it by the BAS.
WARNING: the intend of the function is STRICTLY to allow hardware
drivers to determine which logical channel they control and is NOT
to be used for actual I/O. It is therefore EXPLICITLY allowed that
uart_cpu_busaddr() returns only the lower 8 bits of the address
and garbage in all other bits. No mistakes...
