On AM335x each one of the four GPIO banks has two physical interrupt
lines, so we now allocate resources and setup our interrupt handler for
all the (8) available interrupts.
On OMAP3 and OMAP4 there is only one interrupt for each GPIO bank (6
banks, 6 interrupts), but there are two set of registers where the
first one is used to setup the delivery of interrupts to the MPU and
the second set, setup the delivery of interrupts to the DSP.
On AM335x, each set of registers controls each one of the interrupt
lines.
- Remove nonexistent registers for OMAP4 and AM335x, replace their use with
the correct ones for these SoCs.
- Remove stray whitespace.
Based on OMAP3, OMAP4 and AM335x TRMs.
Tested on Beaglebone-black.
other modes supported by the FTDI serial adapter chips.
In addition to adding the new ioctls, this change removes all the code
that reset the chip at attach and open/close time, and also the code
that turned on RTS/CTS flow control on open without any permission to do
so (that was just always a bug in the driver).
When FTDI chips are configured as GPIO or MPSSE or other special-purpose
uses by an attached serial eeprom, the chip will power on with certain
pins driven or floating, and it's important that the driver not do
anything to the chip to perturb that unless it receives a specific
command to do so. When used for "plain old serial comms" the chip
powers on into the right mode and never needs to be reset while it's
running to operate properly, so this change is transparent to most users.
kqueue_scan() unlocking the kqueue to call f_event, knote() or
knote_fork() should not skip the knote. The knote is not going to
disappear during the influx time, and the mutual exclusion between
scan and knote() is ensured by both code pathes taking knlist lock.
The race appears since knlist lock is before kq lock, so KN_INFLUX
must be set, kq lock must be dropped and only then knlist lock can be
taken. The window between kq unlock and knlist lock causes lost
events.
Add a flag KN_SCAN to indicate that KN_INFLUX is set in a manner safe
for the knote(), and check for it to ignore KN_INFLUX in the knote*()
as needed. Also, in knote(), remove the lockless check for the
KN_INFLUX flag, which could also result in the lost notification.
Reported and tested by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Discussed with: jmg
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
New ZFS property volmode and sysctl vfs.zfs.vol.mode allow switching ZVOL
between three modes:
geom -- existing fully functional behavior (default);
dev -- exposing volumes only as raw disk device file in devfs;
none -- not exposing volumes outside ZFS.
The "dev" mode is less functional (can't be partitioned, mounted, etc),
but it is faster, and in some scenarios with untrusted consumers safer.
It can be useful for NAS, VM block storages, etc.
The "none" mode may be convenient for backup servers, etc. that don't
need direct data access.
Due to the way ZVOL is integrated with main ZFS code, those property
and sysctl are checked only during pool import and volume creation.
MFC after: 1 month
Sponsored by: iXsystems, Inc.
- Include <sys/_types.h> and define pid_t.
- Add __BEGIN_DECLS/__END_DECLS.
In my opinion we should have considered putting the userspace bits in a
different header (e.g., <procdesc.h>), but I think we've already passed
that point.
enabled. Also switch IMX6 to use SCHED_ULE.
The now-unreferenced WANDBOARD.common config will be deleted after giving
folks who may be including it a heads-up to switch to IMX6.
The pdfork(2) man page states:
"pdfork() returns a PID, 0 or -1, as fork(2) does."
As it returns a PID, the return type should obviously be pid_t. As int
and pid_t have the same size on all architectures, this change does not
affect the ABI in any way.
XDTP is used as the default SYSROOT for clang and thus should be an absolute path.
PR: arm/188249
Submitted by: Edgar Martinez <wink15987@gmail.com>
Reviewed by: imp
- Add cpu_cpwait to comply with the convention.
- Add missing TLB invalidations, especially in pmap_kenter & pmap_kremove
with distinguishing between D and ID pages.
- Modify pmap init/bootstrap invalidations to ID, just to be safe.
- Fix TLB-inv and PTE_SYNC ordering.
This combines changes submitted by ian@, cognet@, and Wojciech Macek,
which have all been tested together as a unit.
Perform sychronization (by "isb" barrier) after TTB is set. This
is done to ensure that TLB invalidation always executes after
TTB modification and operates on valid CP15 data (per specification).
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian@, cognet@
This mimics the behaviour in clang and lets us build cleanly
the libdispatch port on platforms where the base gcc is still
the default compiler.
Bump __FreeBSD_version for ports.
Tested by: theraven
MFC after: 3 days
before changing the divisor bits in the register. We were writing a zero
to the register, which clears the enable, but also cleared the divisor bits
at the same time. That's a violation of the sdhci spec, which says the
divisor can only be changed when the clock is disabled. This has worked
okay on most hardware for years, but the TI OMAP controller would misbehave
after changing the divisor improperly.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
- Don't allow high-speed mode on OMAP4 due to hardware erratum.
- Check the proper bit in the status register when waiting for the
controller to come out of reset.
- Add handling for the "non-removable" fdt property by always returning
"card is present" status.
- Add the non-removable property for the MMC card on a Beaglebone Black.
- Add the non-removable property for Pandaboard as a workaround.
For Pandaboard the card detect pin is handled by the twl6030 fpga device
which gets an interrupt on pin change and then has to query the fpga
for the actual status. We don't have code to do that yet.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
