The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
This adds the ethernet MAC and ethernet switch definitions.
I've rewritten the header file and the DTS based on documentation
and the required driver fields rather than the GPL'ed
ones from openwrt.
Differential Revision: https://reviews.freebsd.org/D34111
Reviewed by: manu
These are hardware configuration options which are required in
the linux/openwrt device trees for the IPQ4018/IPQ4019 devices.
Since this isn't obtained from linux upstream but instead from
openwrt, this can't go in contrib; instead it is going in
sys/dts/include/ .
Obtained from: OpenWRT
Tested:
* IPQ4019 ASUS RT-AC58U AP, initial bootstrapping
These ones were unambiguous cases where the Foundation was the only
listed copyright holder (in the associated license block).
Sponsored by: The FreeBSD Foundation
These are all FreeBS-specific device tree files. We don't support any
of these anymore, remove them.
Reviewed by: emaste, manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D28365
The old vendor tree was never fully merged and doing partial merge isn't
supported with git subtree merge so a new one was created.
Switch the build to use the new DTS from sys/contrib/device-tree
This also bump the DTS used to be in sync with Linux 5.9
While here change the way to get the linux version, simply hardcode
the value in sys/dts/freebsd-compatible.dts and use awk to get that
to put it in the CFLAGS.
As a bonus we now have the bindings docs available
in sys/contrib/device-tree/Bindings/ so no need to link to the Linux repo
or to the vendor tree.
Add 64-bit address support to Cadence CGEM Ethernet driver for use in
other SoCs such as the Zynq UltraScale+ and SiFive HighFive Unleashed.
Reviewed by: philip, 0mp (manpages)
Differential Revision: https://reviews.freebsd.org/D24304
DTS must be synced with the kernel, add a freebsd,dts-version string in
the root node of each DTS that we compile so we can later in the kernel
check that it contain a correct value.
Reviewed by: imp, mmel
Differential Revision: https://reviews.freebsd.org/D26724
The upstream DTS now include the thermal device node and the SID
calibration entry.
Update our driver to cope with this change and remove the DTB
overlays that aren't needed anymore.
MFC after: 2 months
X-MFC-With: r359934
It doesn't exist in mainline dts due to the issues related
with detaching and reattaching USB3 devices as mentioned in
https://patchwork.kernel.org/patch/10853381/
In case of FreeBSD, as a temporary workaround "usbconfig reset"
command can fix the problem.
Reviewed by: manu
This is a qspi driver for the Xilinx Zynq-7000 chip.
It could be useful for anyone wanting to boot a system from flash memory
instead of SD cards.
Submitted by: Thomas Skibo (thomasskibo@yahoo.com)
Differential Revision: https://reviews.freebsd.org/D14698
This overlays can be used on A64 board to use spigen and spi(8)
on the spi0 pins.
Tested On: Pine64-LTS, A64-Olinuxino
Submitted by: Gary Otten <gdotten@gmail.com>
RPI is using the firmware provided DTS since 12.0
Pandaboard works with the Linux DTS
RK* Exynos* and Meson*/Odroid* don't even work with current
source code, if someone wants to make them work again they
better use the Linux DTS.
update of devicetree to 4.19 in r340337.
Our build system doesn't provide dependencies for included DTS files, so
nobody noticed this issue for long time.
PR: 235362
MFC after: 1 week
- Remove CS=2 entry from spigen-rpi2 since it didn't work
- Add spigen-rpi3 overlay for Raspberry Pi 3
- Enable rpi overlay modules for GENERIC kernel on aarch64
PR: 233489
Submitted by: bobf@mrp3.com
Reviewed by: db
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D16088
This is the frequency of the cpu on the Pinebook so add it to make
cpufreq find the current setting.
Note that this dtbo on the Pinebook doesn't work right now as u-boot
dtb doesn't have symbols and so it fails to apply. Linux 4.20 have
the dts and will be imported once taggued.
MFC after: 1 month
X-MFC with: r341268
There were two main problems here:
1.) sys/dts/Makefile.inc is not included from various */overlays directories
by default, only ../Makefile.inc
2.) When shelling out for DTS/DTSO, cwd != .CURDIR, so enumeration always
failed
These changes allow make test-dts and make test-dtso to function in their
respective directories.
Reviewed by: manu
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D17961
(e.g. RocketChip, lowRISC and derivatives).
RISC-V page table entries support A (accessed) and D (dirty) bits. The
spec makes hardware support for these bits optional. Implementations that
do not manage these bits in hardware raise page faults for accesses to a
valid page without A set and writes to a writable page without D set.
Check for these types of faults when handling a page fault and fixup the
PTE without calling vm_fault if they occur.
Reviewed by: jhb, markj
Approved by: re (gjb)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D17424
- sun50i-a64-sid.dtso registers the Security ID node, needed for thermal
- sun50i-a64-ths.dtso registers the thermal node, for which we already have a
driver
- sun50i-a64-timer.dtso registers the timer node, needed as the generic timer
glitch on A64 SoC.
Approved by: re (gjb)
