archaic at this point in time. Pretend nobody runs FreeBSD 1.x anymore
in order to not confuse people needlessly.
Laplink support probably doesn't even work at this point in time anyway...
user mode. This goes with rev.1.468 of machdep.c which changed the gates
for these traps to interrupt gates. Having the interrupts disabled for
these traps from user mode is just an unwanted side effect.
This fixes at least 1 case of "panic: absolutely cannot call
smp_ipi_shootdown with interrupts already disabled". Too much code was
run with interrupts disabled, and it sometimes hit a sanity check.
Fix verified by: deischen
variable. The implementation is based upon the patch sent to
arch@, but modified to be compatible with NetBSD. The modifier
that does a reverse sort has been dropped for now, but the
ability to add one later has been preserved.
sending an ICMP packet doesn't cause a panic. A better solution is needed;
possibly defering the transmit to a dedicated thread.
Observed by: "Aaron Wohl" <freebsd@soith.com>
COM_NOFIFO() and COM_ESP cases are supposed to be a subsets of the
plain 16550A case, but 16650-related changes made the former fall into
the latter and then both fall into general code for printing the tx
fifo size. This mainly caused hard to parse boot messages like:
"sio0: type 16550A fifo disabled lookalike with 1 bytes FIFO".
COM_NOFIFO() on an ESP port gave a larger mess whose extent is not
clear.
Fixed some nearby style bugs.
defined values instead of hard-coded values. Don't repeat the register
access part of the code 4 times times or triple-space statements. This
fixes half of the style bugs in rev.1.172.
Hardware flow control of 16650As is still officially unsupported. I
was mistaken about it being broken. It is broken in 16650s but is
fixed in 16650As except for the maximum trigger level (which is no
longer used). Testing of the 16650's broken hardware flow control
watermarks by programming them on 16950s showed that their effects are
not too bad if the fifo size and trigger level are reasonably large
(16 is much better than 8).
usage() has been made a (non-void) function so that it can be
used in a pointer expression (see macro `next'). Widen the
implied integer return type of usage() so that we can cast to
a pointer without warnings.
an UART interface could get stuck when a new interrupt condition
arose while servicing a previous interrupt. Since an interrupt was
already pending, no new interrupt would be triggered.
Avoid infinite recursion by flushing the Rx FIFO and marking an
overrun condition when we could not move the data from the Rx
FIFO to the receive buffer in toto. Failure to flush the Rx FIFO
would leave the Rx ready condition pending.
Note that the SAB 82532 already did this due to the nature of the
chip.
from the sparc64 subtree, which breaks building non-sparc64 platforms
in the event the sparc64 subtree does not exist.
The problem is specific to the module, because non-module builds are
affected by the presence or absence of "device ebus" in the kernel
configuration.
PR: kern/56869
precisely where locking would be needed before adding it, but it
seems uart(4) draws slightly too much attention to have it without
locking for too long.
The lock added is a spinlock that protects access to the underlying
hardware. As a first and obvious stab at this, each method of the
hardware interface grabs the lock. Roughly speaking this serializes
the methods. Exceptions are the probe, attach and detach methods.
o change timeout to MPSAFE callout
o restructure rule deletion to deal with locking requirements
o replace static buffer used for ipfw control operations with malloc'd storage
Sponsored by: FreeBSD Foundation
o change time to MPSAFE callout
o make debug printfs conditional on DUMMYNET_DEBUG and runtime controllable
by net.inet.ip.dummynet.debug
o make boot-time printf dependent on bootverbose
Sponsored by: FreeBSD Foundation
