Back in the mists of time, before EISA came along and required per-pin
level control in the ELCR register, the i8259 had a single chip-wide
level-mode control in bit 3 of ICW1.
Even in the PIIX3 datasheet from 1996 this is documented as 'This bit is
disabled', but apparently MorphOS is using it in the version of the
i8259 which is in the Pegasos2 board as part of the VT8231 chipset.
It's easy enough to implement, and I think it's harmless enough to do so
unconditionally.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[balaton: updated commit message as asked by author]
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <3f09b2dd109d19851d786047ad5c2ff459c90cd7.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Some length properties are signed, other unsigned:
hw/mips/cps.c:183: DEFINE_PROP_UINT32("num-vp", MIPSCPSState, num_vp, 1),
hw/mips/cps.c:184: DEFINE_PROP_UINT32("num-irq", MIPSCPSState, num_irq, 256),
hw/misc/mips_cmgcr.c:215: DEFINE_PROP_INT32("num-vp", MIPSGCRState, num_vps, 1),
hw/misc/mips_cpc.c:167: DEFINE_PROP_UINT32("num-vp", MIPSCPCState, num_vp, 0x1),
hw/misc/mips_itu.c:552: DEFINE_PROP_INT32("num-fifo", MIPSITUState, num_fifo,
hw/misc/mips_itu.c:554: DEFINE_PROP_INT32("num-semaphores", MIPSITUState,
Since negative values are not used (the minimum is '0'),
unify by declaring all properties as unsigned.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230203113650.78146-9-philmd@linaro.org>
Qemu_get_cpu uses the logical CPU id assigned during init to fetch the
CPU state. However APLIC, IMSIC and ACLINT contain registers and states
which are specific to physical hart Ids. The hart Ids in any given system
might be sparse and hence calls to qemu_get_cpu need to be replaced by
cpu_by_arch_id which performs lookup based on the sparse physical hart IDs.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230303065055.915652-3-mchitale@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
i8259_init() helper creates a i8259 device on an ISA bus,
connects its IRQ output to the parent's input IRQ, and
returns an array of 16 ISA input IRQs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-2-philmd@linaro.org>
The ioapic sources reside in hw/intc already. Move the headers there
as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-11-shentey@gmail.com>
[PMD: Keep ioapic_internal.h in hw/intc/, not under include/]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This is in preparation to moving the hflags code into its own file
under the tcg/ directory.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no point in using a void pointer to access the NVIC.
Use the real type to avoid casting it while debugging.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230206223502.25122-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mark up the sysreg definitions for the registers trapped
by HFGRTR/HFGWTR bits 36..63.
Of these, some correspond to RAS registers which we implement as
always-UNDEF: these don't need any extra handling for FGT because the
UNDEF-to-EL1 always takes priority over any theoretical
FGT-trap-to-EL2.
Bit 50 (NACCDATA_EL1) is for the ACCDATA_EL1 register which is part
of the FEAT_LS64_ACCDATA feature which we don't yet implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-14-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-14-peter.maydell@linaro.org
We currently only support GICv2 emulation. To also support GICv3, we will
need to pass a few system registers into their respective handler functions.
This patch adds support for HVF to call into the TCG callbacks for GICv3
system register handlers. This is safe because the GICv3 TCG code is generic
as long as we limit ourselves to EL0 and EL1 - which are the only modes
supported by HVF.
To make sure nobody trips over that, we also annotate callbacks that don't
work in HVF mode, such as EL state change hooks.
With GICv3 support in place, we can run with more than 8 vCPUs.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20230128224459.70676-1-agraf@csgraf.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip are defined
in pnv.h. Many users of the header don't actually need them. One
instance is this inclusion loop: hw/ppc/pnv_homer.h includes
hw/ppc/pnv.h for typedef PnvChip, and vice versa for struct PnvHomer.
Similar structs live in their own headers: PnvHomerClass and PnvHomer
in pnv_homer.h, PnvLpcClass and PnvLpcController in pci_lpc.h,
PnvPsiClass, PnvPsi, Pnv8Psi, Pnv9Psi, Pnv10Psi in pnv_psi.h, ...
Move PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip to new
pnv_chip.h, and adjust include directives. This breaks the inclusion
loop mentioned above.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221222104628.659681-2-armbru@redhat.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Seems like there is also nothing target-specific in here, so these
files can be moved to softmmu_ss to avoid that they get compiled
twice (once for qemu-system-arm and once for qemu-system-aarch64).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230112134928.1026006-7-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Goldfish interrupt controller is not target specific.
While the Exynos interrupt combiner is only used by the ARM
targets, we can build this device once for all.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221209170042.71169-3-philmd@linaro.org>
[thuth: Change patch title, and also move 'exynos4210_gic.c']
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230112134928.1026006-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
A bunch of cleanups from various people.
- Improved GT64120 on big-endian hosts
- GT64120 north bridge and MC146818 RTC devices are now target independent
- Bonito64 north bridge converted to 3-phase reset API
- PCI refactors around PIIX devices
- Support for nanoMIPS in bootloader generator API
- New YAMON Malta Avocado test
- Removal of 'trap and emulate' KVM support
- System-specific QMP commands restricted to system emulation
-----BEGIN PGP SIGNATURE-----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=oXX+
-----END PGP SIGNATURE-----
Merge tag 'mips-20230113' of https://github.com/philmd/qemu into staging
MIPS patches queue
A bunch of cleanups from various people.
- Improved GT64120 on big-endian hosts
- GT64120 north bridge and MC146818 RTC devices are now target independent
- Bonito64 north bridge converted to 3-phase reset API
- PCI refactors around PIIX devices
- Support for nanoMIPS in bootloader generator API
- New YAMON Malta Avocado test
- Removal of 'trap and emulate' KVM support
- System-specific QMP commands restricted to system emulation
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmPBekAACgkQ4+MsLN6t
# wN4wjxAAtYxyt6WUBpiYfV/LnbQFpAsacues1Vhy9MPYEg5a/iuXWKvWtgRYvGww
# qR0GVQH8rH7tgnCZK+ioq9jX+hvfBskP6CnKhxmb5zDGm7vP7jhhu8UFWY/EtBgq
# 0zpNeLMXtnRJ6PBqo/nWFCVtcpDRZ6IkSbpGWkVkciRFc5n/2VCnlIj8k2I1oMvL
# 11cp2xFQnaPReFXIpMjJHuHv1NObykdlvVg6wQo/A/4qIb8EvJQEPmePjG9Sf0i0
# v2dhnnxG9mze7+uq0dIC16x8Azko3N7dmtNlBU/aGb9OELwx35aux2M4dNDVogwn
# DqL/Wsk54TFewECOfS48t/a/TqV8j/ISW1d/JvovBrN2KovmIAbtqHuMUqKVk5l0
# 23ZOIIPIYwmScZwIlkCIGUuIzFig1zhEmQcoEQaFe/B0oLB2eN/x0Bk9Yklo+i2A
# WNiyiAj7k5492qEdndOySEEDVt6886F/+CdQ6QYF5Z1L/ELck7XHBH3mGDznWpPn
# 6IURyVquPJx7ul62jSGI+Gc+qakNoahIhPo5O7hklOM9GwWNOWXHveyb7xjs7j+O
# eWyVcet+o7hoHkCzmfbyTPySI4qCpF9fA42jqPhATwQPwmGXpbr+4BxUq3KtE43y
# w9tEigwd4voN3dWLItVh6QE4in70osz3XHp93byvo8bHlS0huVY=
# =oXX+
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 13 Jan 2023 15:35:28 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'mips-20230113' of https://github.com/philmd/qemu: (46 commits)
scripts/git.orderfile: Display MAINTAINERS changes first
target/mips: Restrict 'qapi-commands-machine.h' to system emulation
hw/mips/boston: Rename MachineState 'mc' pointer to 'ms'
hw/pci-host/bonito: Declare TYPE_BONITO_PCI_HOST_BRIDGE in header
hw/pci-host/bonito: Use 'bonito_pci' for PCI function #0 code
hw/pci-host/bonito: Use 'bonito_host' for PCI host bridge code
hw/pci-host/bonito: Convert to 3-phase reset
softmmu/rtc: Emit warning when using driftfix=slew on systems without mc146818
hw/rtc/mc146818rtc: Make the mc146818 RTC device target independent
hw/core/qdev-properties-system: Allow the 'slew' policy only on x86
hw/intc: Extract the IRQ counting functions into a separate file
hw/intc/i8259: Make using the isa_pic singleton more type-safe
hw/usb/hcd-uhci: Introduce TYPE_ defines for device models
hw/mips/Kconfig: Track Malta's PIIX dependencies via Kconfig
hw/isa/piix4: Decouple INTx-to-LNKx routing which is board-specific
hw/isa/piix3: Decouple INTx-to-LNKx routing which is board-specific
hw/pci/pci: Factor out pci_bus_map_irqs() from pci_bus_irqs()
hw/pci/pci_host: Trace config accesses on unexisting functions
mips: Always include nanomips disassembler
mips: Remove support for trap and emulate KVM
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These IRQ counting functions will soon be required in binaries that
do not include the APIC code, too, so let's extract them into a
separate file that can be linked independently of the APIC code.
While we're at it, change the apic_* prefix into kvm_* since the
functions are used from the i8259 PIC (i.e. not the APIC), too.
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230110095351.611724-2-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This even spares some casts in hot code paths along the way.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-10-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This remove a use of 'struct' in the DECLARE_INSTANCE_CHECKER()
macro call, to avoid after a QOM refactor:
hw/intc/xilinx_intc.c:45:1: error: declaration of anonymous struct must be a definition
DECLARE_INSTANCE_CHECKER(struct xlx_pic, XILINX_INTC,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Message-id: 20230109140306.23161-14-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Following docs/devel/style.rst guidelines, rename
omap_intr_handler_s -> OMAPIntcState. This also remove a
use of 'struct' in the DECLARE_INSTANCE_CHECKER() macro call.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCY7e94gAKCRBAov/yOSY+
3+YwA/9JAerEGzZIJfV2+QK4LWONOfIt7Ns5TR93gTjd+9rTsahgSIHRa2XHQLWZ
TwY2eyTf8M+qiVOKa1wTCEfvr/iQwRuJBmsyQ/igdKgylEi9t6GEIG1NeGUxGkkR
sCBJMtcqB4OKIX6PlyRiOm9kJxnNgQuiQ6ZB7uqIcVuYC/wxzA==
=KsDP
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20230106
# gpg: Signature made Fri 06 Jan 2023 06:21:22 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_pch: Change default irq number of pch irq controller
hw/intc/loongarch_pch_pic: add irq number property
hw/intc/loongarch_pch_msi: add irq number property
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the default irq number of pch pic to 32, so that the irq
number of pch msi is 224(256 - 32), and move the 'PCH_PIC_IRQ_NUM'
macro to pci-host/ls7a.h and add prefix 'VIRT' on it to keep standard
format.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230104020518.2564263-4-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
With loongarch 7A1000 manual, irq number supported can be set
in PCH_PIC_INT_ID_HI register. This patch adds irq number property
for loongarch_pch_pic, so that virt machine can set different
irq number when pch_pic intc is added.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230104020518.2564263-3-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
This patch adds irq number property for loongarch msi interrupt
controller, and remove hard coding irq number macro.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230104020518.2564263-2-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
The pending register upper limit is currently set to
plic->num_sources >> 3, which is wrong, e.g.: considering
plic->num_sources is 7, the upper limit becomes 0 which fails
the range check if reading the pending register at pending_base.
Fixes: 1e24429e40 ("SiFive RISC-V PLIC Block")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-16-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the SiFive PLIC model "priority-base" expects interrupt
priority register base starting from source 1 instead source 0,
that's why on most platforms "priority-base" is set to 0x04 except
'opentitan' machine. 'opentitan' should have set "priority-base"
to 0x04 too.
Note the irq number calculation in sifive_plic_{read,write} is
correct as the codes make up for the irq number by adding 1.
Let's simply update "priority-base" to start from interrupt source
0 and add a comment to make it crystal clear.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-14-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the default value of "num-sources" property is zero,
which does not make a lot of sense, as in sifive_plic_realize()
we see s->bitfield_words is calculated by:
s->bitfield_words = (s->num_sources + 31) >> 5;
if the we don't configure "num-sources" property its default value
zero makes s->bitfield_words zero too, which isn't true because
interrupt source 0 still occupies one word.
Let's change the default value to 1 meaning that only interrupt
source 0 is supported by default and a sanity check in realize().
While we are here, add a comment to describe the exact meaning of
this property that the number should include interrupt source 0.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-9-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The realize() callback has an errp for us to propagate the error up.
While we are here, correct the wrong multi-line comment format.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-8-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PLIC config parser can only handle legal config string
like "MS,MS". However if a config string like ",MS,MS,,MS,MS,," is
given the parser won't get the correct configuration.
This commit improves the config parser to make it more robust.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-7-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
H-mode has been removed since priv spec 1.10. Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-6-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in both riscv_aplic_realize() and
riscv_imsic_realize().
Select MSI_NONBROKEN in RISCV_APLIC and RISCV_IMSIC.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-2-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in sifive_plic_realize().
Let SIFIVE_PLIC select MSI_NONBROKEN and drop the selection from
RISC-V machines.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If the number of interrupt is not multiple of 32, PLIC will have
out-of-bound access to source_priority array. Compute the number of
interrupt in the last word to avoid this out-of-bound access of array.
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20221127165753.30533-1-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 40244040a7 changed the way the S irqs are numbered. This breaks when
using numa configuration, e.g.:
./qemu-system-riscv64 -nographic -machine virt,dumpdtb=numa-tree.dtb \
-m 2G -smp cpus=16 \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-object memory-backend-ram,id=mem2,size=512M \
-object memory-backend-ram,id=mem3,size=512M \
-numa node,cpus=0-3,memdev=mem0,nodeid=0 \
-numa node,cpus=4-7,memdev=mem1,nodeid=1 \
-numa node,cpus=8-11,memdev=mem2,nodeid=2 \
-numa node,cpus=12-15,memdev=mem3,nodeid=3
leads to:
Unexpected error in object_property_find_err() at ../qom/object.c:1304:
qemu-system-riscv64: Property 'riscv.sifive.plic.unnamed-gpio-out[8]' not
found
This patch makes the nubering of the S irqs identical to what it was before.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Message-Id: <20221114135122.1668703-1-frederic.petrot@univ-grenoble-alpes.fr>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Convert the TYPE_ICS class to 3-phase reset; this will allow us
to convert the TYPE_PHB3_MSI class which inherits from it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-7-peter.maydell@linaro.org
The realize method for the TYPE_ICS class uses qemu_register_reset()
to register a reset handler, as a workaround for the fact that
currently objects which directly inherit from TYPE_DEVICE don't get
automatically reset. However, the reset function directly calls
ics_reset(), which is the function that implements the legacy reset
method. This means that only the parent class's data gets reset, and
a subclass which also needs to handle reset, like TYPE_PHB3_MSI, has
to register its own reset function.
Make the TYPE_ICS reset function call device_cold_reset() instead:
this will handle reset for both the parent class and the subclass,
and will work whether the classes are using legacy reset or 3-phase
reset. This allows us to remove the reset function that the subclass
currently has to set up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-6-peter.maydell@linaro.org
Convert the TYPE_KVM_ARM_ITS device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-10-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_ITS device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-9-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_ITS_COMMON parent class to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109161444.3397405-8-peter.maydell@linaro.org
Convert the TYPE_KVM_ARM_GICV3 device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-7-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_COMMON parent class to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-6-peter.maydell@linaro.org
Now we have converted TYPE_ARM_GIC_COMMON, we can convert the
TYPE_ARM_GIC_KVM subclass to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-5-peter.maydell@linaro.org
Convert the TYPE_ARM_GIC_COMMON device to 3-phase reset. This is a
simple no-behaviour-change conversion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109161444.3397405-4-peter.maydell@linaro.org
The ARM GICv3 TRM describes that the ITLinesNumber field of GICD_TYPER
register:
"indicates the maximum SPI INTID that the GIC implementation supports"
As SPI #0 is absolute IRQ #32, the max SPI INTID should have accounted
for the internal 16x SGI's and 16x PPI's. However, the original GICv3
model subtracted off the SGI/PPI. Cosmetically this can be seen at OS
boot (Linux) showing 32 shy of what should be there, i.e.:
[ 0.000000] GICv3: 224 SPIs implemented
Though in hw/arm/virt.c, the machine is configured for 256 SPI's. ARM
virt machine likely doesn't have a problem with this because the upper
32 IRQ's don't actually have anything meaningful wired. But, this does
become a functional issue on a custom use case which wants to make use
of these IRQ's. Additionally, boot code (i.e. TF-A) will only init up
to the number (blocks of 32) that it believes to actually be there.
Signed-off-by: Luke Starrett <lukes@xsightlabs.com>
Message-id: AM9P193MB168473D99B761E204E032095D40D9@AM9P193MB1684.EURP193.PROD.OUTLOOK.COM
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
a66a24585f (hw/intc/arm_gic: Implement read of GICC_IIDR) implemented
this for the CPU interface register. The fact we don't implement it
shows up when running Xen with -d guest_error which is definitely
wrong because the guest is perfectly entitled to read it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gic_dist_readb was returning a word value which just happened to work
as a result of the way we OR the data together. Lets fix it so only
the explicit byte is returned for each part of GICD_TYPER. I've
changed the return type to uint8_t although the overflow is only
detected with an explicit -Wconversion.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With commit 39f29e5993 ("hw/intc/arm_gicv3: Use correct number of
priority bits for the CPU") the number of priority bits was changed from
the maximum value 8 to typically 5. As a consequence a few of the lowest
bits in ICC_PMR_EL1 becomes RAZ/WI. However prior to this patch one of
these bits was still used since the supplied priority value is masked
before it's eventually right shifted with one bit. So the bit is not
lost as one might expect when the register is read again.
The Linux kernel depends on lowest valid bit to be reset to zero, see
commit 33625282adaa ("irqchip/gic-v3: Probe for SCR_EL3 being clear
before resetting AP0Rn") for details.
So fix this by masking the priority value after it may have been right
shifted by one bit.
Cc: qemu-stable@nongnu.org
Fixes: 39f29e5993 ("hw/intc/arm_gicv3: Use correct number of priority bits for the CPU")
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
1. When cpu read or write extioi COREISR reg, it should access
the reg belonged to itself, so the cpu index of 's->coreisr'
is current cpu number. Using MemTxAttrs' requester_id to get
the cpu index.
2. it need not to mask 0x1f when calculate the coreisr array index.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221021015307.2570844-3-yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
