ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
This is the first step in removing get_pdma_buf() from esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-17-mark.cave-ayland@ilande.co.uk>
The limiting of DMA transfers to the maximum size of the available data is already
handled by esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-15-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
This function simplifies reading the STC register value without having to manually
shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-11-mark.cave-ayland@ilande.co.uk>
These functions simplify reading and writing the TC register value without having to
manually shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-10-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
Move the trace event to the end of the function so that it correctly reports
the returned value if it doesn't come directly from the rregs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-7-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
-----BEGIN PGP SIGNATURE-----
iQEyBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBA8k8ACgkQIeENKd+X
cFRRMgf41R7Zn1ZSB9GHL3WgLDTPqpT4FAMpTnYRD7wPdspawl1SsHWBgaLNmJWk
dwSLhvHMM44pOVCQRqdkiRrp5t5fDEm6gdRKyNn5uzWFMn7ibYIjmg7OE+79onbN
VES4yTJwuskD/7JRNcrW6RytKRgzKs2au8NxxgtgXprSF0nM9wCu70z4T9XkLfjQ
cpJUUaUCw628uUic/nObTxMnaiEmq/C0qU9SRRKPYVRp7jceCsHMVRazqOgdM6uf
foNHi/uCNKy6I841+D8Po7h57s51LtT78JDRRVRPfWY+SRQyC5l8Eq3UtRPyg39p
7hhkiAKhG4rs8iCXKvMvTz0S//Cx
=BVLq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210304' into staging
RISC-V PR for 6.0
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
# gpg: Signature made Thu 04 Mar 2021 14:44:31 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210304:
hw/riscv: virt: Map high mmio for PCIe
hw/riscv: virt: Limit RAM size in a 32-bit system
hw/riscv: virt: Drop the 'link_up' parameter of gpex_pcie_init()
hw/riscv: Drop 'struct MemmapEntry'
MAINTAINERS: Add a SiFive machine section
goldfish_rtc: re-arm the alarm after migration
docs/system: riscv: Add documentation for sifive_u machine
docs/system: Add RISC-V documentation
docs/system: Sort targets in alphabetical order
hw/riscv: sifive_u: Change SIFIVE_U_GEM_IRQ to decimal value
hw/riscv: sifive_u: Add QSPI2 controller and connect an SD card
hw/riscv: sifive_u: Add QSPI0 controller and connect a flash
hw/ssi: Add SiFive SPI controller support
hw/block: m25p80: Add various ISSI flash information
hw/block: m25p80: Add ISSI SPI flash support
target-riscv: support QMP dump-guest-memory
roms/opensbi: Upgrade from v0.8 to v0.9
hw/misc: sifive_u_otp: Use error_report() when block operation fails
target/riscv: Declare csr_ops[] with a known size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some peripherals require 64-bit PCI address, so let's map the high
mmio space for PCIe.
For RV32, the address is hardcoded to below 4 GiB from the highest
accessible physical address. For RV64, the base address depends on
top of RAM and is aligned to its size which is using 16 GiB for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RV32 supports 34-bit physical address hence the maximum RAM size
should be limited. Limit the RAM size to 10 GiB, which leaves
some room for PCIe high mmio space.
For 32-bit host, this is not needed as machine->ram_size cannot
represent a RAM size that big. Use a #if size test to only do
the size limitation for the 64-bit host.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
`link_up` is never used in gpex_pcie_init(). Drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the RISC-V defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210220144807.819-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
After a migration the clock offset is updated, but we also
need to re-arm the alarm if needed.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201220112615.933036-7-laurent@vivier.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the SiFive SPI controller model for the FU540 SoC.
The direct memory-mapped SPI flash mode is unsupported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This updates the flash information table to include various ISSI
flashes that are supported by upstream U-Boot and Linux kernel.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the ISSI SPI flash support. The number of dummy cycles in
fast read, fast read dual output and fast read quad output commands
is currently using the default 8. Likewise, the same default value
is used for fast read dual/quad I/O command. Per the datasheet [1],
the number of dummy cycles is configurable, but this is not modeled
at present.
For flash whose size is larger than 16 MiB, the sequence of 3-byte
address along with EXTADD bit in the bank address register (BAR) is
not supported. We assume that guest software always uses op codes
with 4-byte address sequence. Fortunately, this is the case for both
U-Boot and Linux spi-nor drivers.
QPI (Quad Peripheral Interface) that supports 2-cycle instruction
has different default values for dummy cycles of fast read family
commands, and is unsupported at the time being.
[1] http://www.issi.com/WW/pdf/25LP-WP256.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present when blk_pread() / blk_pwrite() fails, a guest error
is logged, but this is not really a guest error. Change to use
error_report() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1611026585-29971-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A pwrite() call returns the number of bytes written (or -1 on error),
and vfio-ccw compares this number with the size of the region to
determine if an error had occurred or not.
If they are not equal, this is a failure and the errno is used to
determine exactly how things failed. An errno of zero is possible
(though unlikely) in this situation and would be translated to a
successful operation.
If they ARE equal, the ret_code field is read from the region to
determine how to proceed. While the kernel sets the ret_code field
as necessary, the region and thus this field is not "written back"
to the user. So the value can only be what it was initialized to,
which is zero.
So, let's convert an unexpected length with errno of zero to a
return code of -EFAULT, and explicitly set an expected length to
a return code of zero. This will be a little safer and clearer.
Suggested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20210303160739.2179378-1-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The virtio standard specifies that any non-transitional device must
reject commands prior to revision setting (which we do). Devices
that are transitional need to assume revision 0 (legacy) if the
driver sends a non-revision-setting command first in order to
support legacy drivers. We neglected to do the latter.
Fortunately, nearly everything worked as intended anyway; the only
problem was not properly rejecting revision setting after some other
command had been issued. Easy to fix by setting revision to 0 if
we see a non-revision command on a legacy-capable revision-less
device.
Found by code inspection, not observed in the wild.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210216111830.1087847-1-cohuck@redhat.com>
Some CLP response data was accidentally dropped when fixing endianness
issues with the Query PCI Function CLP response. All of these values are
sent as 0s to the guest for emulated devices, so the impact is only
observed on passthrough devices.
Fixes: a4e2fff1b1 ("s390x/pci: fix endianness issues")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <1613681609-9349-1-git-send-email-mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 2c44220d05 ("meson: convert hw/arch*"), which migrated the old
Makefile.objs to meson.build accidentally excluded virtio-ccw-9p.c and
thus the virtio-9p-ccw device from the build (and potentially also
included the file virtio-ccw-blk.c twice in the source set). And since
CONFIG_VIRTFS can't be used the way it was used here (see commit
2c9dce0196 ("meson: do not use CONFIG_VIRTFS")), the preconditions have
to be written differently.
Let's fix this!
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 2c44220d05 ("meson: convert hw/arch*")
Reported-by: Jakob Naucke <jakob.naucke@ibm.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210218034059.1096078-1-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In the past, virtio-gpu set NULL as the surface for the secondary
consoles to hide its window. The distinction is now handled in
ui/console and the display backends and virtio-gpu does no longer
have to do that.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20210225101316.83940-3-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The surfaces created with former qemu_create_message_surface
did not display the content from the guest and always contained
simple messages describing the reason.
A display backend may want to hide the window showing such a
surface. This change renames the function to
qemu_create_placeholder_surface, and adds "placeholder" flag; the
display can check the flag to decide to do anything special like
hiding the window.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20210225101316.83940-1-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmA+SYcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpUAAIALa9WkjdxjZhb4FzP1OLBSTEISLEfrPE4Zk/
s5yY1wEDvH83D6fxTHv1B8tISwJ3RJn8ZhsP0c0Mb6stT7D33m7YfMFtNXBEfENX
gMgwdC2QxGMZXKGR+dIpxtYghjvuzAVN+e9w27C+s855JJ8y+chghtLuDJIbqpAk
QopftjiZix2bPYmrxlVw/A7inXL2jseJyYsgGAzIACmsGC70jK4Rk1vxrAF+2n15
D4qKOG3QLJXrfIVa8iDz/ojlVUmLWl8jnoE+oY+rjtckQHJKqodlJi5yeJxGEa3/
G7db+AIzEBge78dq7LBSJOTjoUFoQ+6Hv1QtKk2GcMKdEnsj0ng=
=NGys
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,virtio,pci: bug fixes
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 02 Mar 2021 14:19:51 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
vhost: simplify vhost_dev_init() fail_busyloop label
hw/pci: Have safer pcie_bus_realize() by checking error path
virtio-net: handle zero mac for a vdpa peer
i386/acpi: restore device paths for pre-5.1 vms
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmA3tzQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMsngf+OkbgTDouxq3qnn1K89n6j2wKlAj0
qPP+57o1sv5u5MjX0BkawXCMJfvTKJaOt/Cs8S0FaPTehfR5H0T2tL76KZBEdlEP
/+V3EC0Qmd1S47LKIOuDkV15szvnccyjpgwaL7Osjb0Eh0SxeXd4pBTc3yYtkacu
zb/srZ63U2iJZr93QwGmEJjuW57WNym6QWXF3Mrg9PFXybkXFTGumB2vZMlQc+MN
RWPTUKZKAiIr/HfdvpIETXY+HzJhylvIQ8OVWtM3XDorl48OWcOat/jyeNEVYgG3
o+gxIRnfvIL+42GkmUFbOKLzT5SV6p9EYYGLTuE1kU7nc6HWoD0CdPxA3A==
=UBVO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging
* fix --enable-fuzzing linker failures (Alexander)
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
# gpg: Signature made Thu 25 Feb 2021 14:41:56 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini-gitlab/tags/for-upstream: (29 commits)
tcg/i386: rdpmc: fix the the condtions
chardev: do not use short form boolean options in non-QemuOpts character device descriptions
vl: deprecate -writeconfig
target/i386: Add bus lock debug exception support
qom/object.c: Fix typo
target/i386: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -vnc
docs: update to show preferred boolean syntax for -chardev
qemu-options: update to show preferred boolean syntax for -vnc
qemu-options: update to show preferred boolean syntax for -incoming
qemu-options: update to show preferred boolean syntax for -netdev
qemu-options: update to show preferred boolean syntax for -spice
qemu-options: update to show preferred boolean syntax for -chardev
gdbstub: use preferred boolean option syntax
char: don't fail when client is not connected
scsi: drop 'result' argument from command_complete callback
scsi-disk: pass guest recoverable errors through even for rerror=stop
scsi-disk: pass SCSI status to scsi_handle_rw_error
scsi: introduce scsi_sense_from_errno()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Requiring a conditional for every goto is tedious:
if (busyloop_timeout) {
goto fail_busyloop;
} else {
goto fail;
}
Move the conditional to into the fail_busyloop label so that it's safe
to jump to this label unconditionally.
This change makes the migrate_add_blocker() error case more consistent.
It jumped to fail_busyloop unconditionally whereas the memslots limits
error case was conditional.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210222114931.272308-1-stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While pci_bus_realize() currently does not use the Error* argument,
it would be an error to leave pcie_bus_realize() setting bus->flags
if pci_bus_realize() had failed.
Fix by using a local Error* and return early (propagating the error)
if pci_bus_realize() failed.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210201153700.618946-1-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some mlx vdpa devices with kernels at least up to 5.11 currently present
0 as their MAC address. This is because they have not been
pre-configured with a MAC: they have a learning bridge and only learn
the MAC once guest is up. Kernel patches and tools to allow programming
the MAC from host are being developed. For now - since these
combinations exist in the field - let's detect zero mac and just try to
proceed with the mac from the qemu command line.
This makes the guest use this MAC to send packets in turn teaching
the MAC to the card, and things work.
TODO:
report the actual MAC from QEMU commad line in the info message.
TODO:
detect that a (non-zero) hardware MAC does not match QEMU command line
and fail init.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20210225165506.18321-2-lulu@redhat.com>
mst: rewritten code comments, message printed and the commit log.
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Tested-by: Adrian Moreno <amorenoz@redhat.com>
Tested-by: Sean Mooney <smooney@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After fixing the _UID value for the primary PCI root bridge in
af1b80ae it was discovered that this change updates Windows
configuration in an incompatible way causing network configuration
failure unless DHCP is used. More details provided on the list:
https://lists.gnu.org/archive/html/qemu-devel/2021-02/msg08484.html
This change reverts the _UID update from 1 to 0 for q35 and i440fx
VMs before version 5.2 to maintain the original behaviour when
upgrading.
Cc: qemu-stable@nongnu.org
Cc: qemu-devel@nongnu.org
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Message-Id: <20210301195919.9333-1-cheptsov@ispras.ru>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: af1b80ae56 ("i386/acpi: fix inconsistent QEMU/OVMF device paths")
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, recoverable sense values are only passed directly to the
guest only for rerror=report. However, when rerror/werror are 'stop'
we still don't want the host to be involved on every UNIT ATTENTION
(especially considered that the QMP event will not have enough information
to act on the report).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of fishing it from *r->status, just pass the SCSI status
as a positive value of the second parameter and an errno as a
negative value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new function is an extension of the switch statement in scsi-disk.c
which also includes the errno cases only found in sg_io_sense_from_errno.
This allows us to consolidate the errno handling.
Extracted from a patch by Hannes Reinecke <hare@suse.de>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When requested to ignore errors, just do nothing and let the
request complete normally. This means that the request will
be accounted correctly.
This is what commit 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore",
2018-10-19) was supposed to do:
Fixes: 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore", 2018-10-19)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
