Callers are changed to use qerror_report_err() to keep their QError
semantics.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
The only backend that really uses it is the socket one, which calls
monitor_get_fd(). But it can use 'cur_mon' instead.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
This commit converts qemu_opts_create() from qerror_report() to
error_set().
Currently, most calls to qemu_opts_create() can't fail, so most
callers don't need any changes.
The two cases where code checks for qemu_opts_create() erros are:
1. Initialization code in vl.c. All of them print their own
error messages directly to stderr, no need to pass the Error
object
2. The functions opts_parse(), qemu_opts_from_qdict() and
qemu_chr_parse_compat() make use of the error information and
they can be called from HMP or QMP. In this case, to allow for
incremental conversion, we propagate the error up using
qerror_report_err(), which keeps the QError semantics
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
This reverts commit ff71f2e8ca. This is because
the linux 8139cp driver would leave the card in "Config Register Write Enable"
mode after the eeprom were read or write ( which is unexpected in the spec
). Also a physical 8139 card can still DMA into host memory in modes other than
Normal mode, so we need revert this commit to align with the behavior of
physical card.
The issue of 8139cp driver should be fixed in linux seperately.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* qemu-kvm/uq/master:
virtio/vhost: Add support for KVM in-kernel MSI injection
msix: Add msix_nr_vectors_allocated
kvm: Enable use of kvm_irqchip_in_kernel in hwlib code
kvm: Introduce kvm_irqchip_add/remove_irqfd
kvm: Make kvm_irqchip_commit_routes an internal service
kvm: Publicize kvm_irqchip_release_virq
kvm: Introduce kvm_irqchip_add_msi_route
kvm: Rename kvm_irqchip_add_route to kvm_irqchip_add_irq_route
msix: Introduce vector notifiers
msix: Invoke msix_handle_mask_update on msix_mask_all
msix: Factor out msix_get_message
kvm: update vmxcap for EPT A/D, INVPCID, RDRAND, VMFUNC
kvm: Enable in-kernel irqchip support by default
kvm: Add support for direct MSI injections
kvm: Update kernel headers
kvm: x86: Wire up MSI support for in-kernel irqchip
pc: Enable MSI support at APIC level
kvm: Introduce basic MSI support for in-kernel irqchips
Introduce MSIMessage structure
kvm: Refactor KVMState::max_gsi to gsi_count
As in the SATA and AHCI specifications, a FIS is 5 Dwords of 4 bytes
each, which comes to 20 bytes (decimal), not 0x20.
Signed-off-by: Daniel Verkamp <daniel@drv.nu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently the sector value for the geometry is masked, even if the
user usesa command line parameter that explicitely gives a number.
This breaks dasd devices on s390. A dasd device can have
a physical block size of 4096 (== same for logical block size)
and a typcial geometry of 15 heads and 12 sectors per cyl.
The ibm partition detection relies on a correct geometry
reported by the device. Unfortunately the current code changes
12 to 8. This would be necessary if the total size is
not a multiple of logical sector size, but for dasd this
is not the case.
This patch checks the device size and only applies sector
mask if necessary.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The local variables ret, i are only used if __linux__ is defined.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Start VM with 8 multiple-function block devs, hot-removing
those block devs by 'device_del ...' would cause qemu abort.
| (qemu) device_del virti0-0-0
| (qemu) **
|ERROR:qom/object.c:389:object_delete: assertion failed: (obj->ref == 0)
It's a regression introduced by commit 57c9fafe
The whole PCI slot should be removed once. Currently only one func
is cleaned in pci_unplug_device(), if you try to remove a single
func by monitor cmd.
free_qdev() are called for all functions in slot,
but unparent_delete() is only called for one
function.
Signed-off-by: XXXX
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The previous multiboot load code did not treat the case where
load_end_addr was 0 specially. The multiboot specification says the
following:
* load_end_addr
Contains the physical address of the end of the data segment.
(load_end_addr - load_addr) specifies how much data to load. This
implies that the text and data segments must be consecutive in the
OS image; this is true for existing a.out executable formats. If
this field is zero, the boot loader assumes that the text and data
segments occupy the whole OS image file.
Signed-off-by: Scott Moser <smoser@ubuntu.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With pc-0.12, we map the video RAM both through the PCI BAR (the guest does
this) and through a fixed mapping at 0xe0000000. The memory API doesn't allow
this double map, and aborts.
Fix by using an alias.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* sstabellini/for_1.1_rc3:
Call xc_domain_shutdown with the reboot flag when the guest requests a reboot.
xen: Fix PV-on-HVM
xen_disk: properly update stats in ioreq_release()
xen_disk: use bdrv_aio_flush instead of bdrv_flush
xen_disk: remove syncwrite option
xen: disable rtc_clock
xen: do not initialize the interval timer and PCSPK emulator
* kwolf/for-anthony:
fdc-test: introduced qtest no_media_on_start and cmos qtest for floppy
fdc: fix media detection
fdc: floppy drive should be visible after start without media
qemu-iotests: mark 035 qcow2-only
qcow2: Check qcow2_alloc_clusters_at() return value
sheepdog: use heap instead of stack for BDRVSheepdogState
sheepdog: return -errno on error
sheepdog: mark image as snapshot when tag is specified
qemu-img: Explain how rebase operation can be used to perform a 'diff' operation.
qcow2: don't leak buffer for unexpected qcow_version in header
We have to set up 'media_changed' after guest start so floppy driver
could detect that there is no media in drive. For this purpose we call
'fdctrl_change_cb' instead of 'fd_revalidate' in 'fdctrl_connect_drives'.
'fd_revalidate' is called inside 'fdctrl_change_cb'.
We still have to set default drive geometry in 'fd_revalidate' even
if there is no media in drive. When you try to open (windows) or mount (linux)
floppy the driver tries to seek on track 1. Linux guest stuck in loop then
kernel crashes and windows guest prints error message.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If you start guest with floppy drive but without media inserted, guest
still should see floppy drive pressent.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When DEBUG_ES1370 is defined, the compiler shows these warnings:
hw/es1370.c: In function ?es1370_update_voices?:
hw/es1370.c:414: warning: format ?%d? expects type ?int?, but argument 3 has type ?size_t?
hw/es1370.c: In function ?es1370_writel?:
hw/es1370.c:582: warning: format ?%d? expects type ?int?, but argument 3 has type ?long int?
hw/es1370.c:592: warning: format ?%d? expects type ?int?, but argument 3 has type ?long int?
hw/es1370.c:609: warning: format ?%d? expects type ?int?, but argument 3 has type ?long int?
hw/es1370.c: In function ?es1370_readl?:
hw/es1370.c:751: warning: suggest braces around empty body in an ?if? statement
Fix the format strings and add the missing braces.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: malc <av1474@comtv.ru>
In the context of PV-on-HVM under Xen, the emulated nics are supposed to be
unplug before the guest drivers are initialized, when the guest write to a
specific IO port.
Without this patch, the guest end up with two nics with the same MAC, the
emulated nic and the PV nic.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The str allocated in visit_type_str was not freed.
The visit_type_str function is an input visitor(<QMP/String/etc>-to-native)
here, it will allocate memory for caller, so the caller is responsible for
freeing the memory.
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: dunrong huang <riegamaths@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
VIRTIO_BLK_F_SCSI is supposed to mean whether the host can *parse*
SCSI requests, not *execute* them. You could run QEMU with scsi=on
and a file-backed disk, and QEMU would fail all SCSI requests even
though it advertises VIRTIO_BLK_F_SCSI.
Because we need to do this to fix a migration compatibility problem
related to how QEMU is invoked by management, we must do this
unconditionally even on older machine types. This more or less assumes
that no one ever invoked QEMU with scsi=off.
Here is how testing goes:
- old QEMU, scsi=on -> new QEMU, scsi=on
- new QEMU, scsi=on -> old QEMU, scsi=on
- old QEMU, scsi=off -> new QEMU, scsi=on
- new QEMU, scsi=off -> old QEMU, scsi=on
ok (new QEMU has VIRTIO_BLK_F_SCSI, adding host features is fine)
- old QEMU, scsi=off -> new QEMU, scsi=off
ok (new QEMU has VIRTIO_BLK_F_SCSI, adding host features is fine)
- old QEMU, scsi=on -> new QEMU, scsi=off
ok, bug fixed
- new QEMU, scsi=on -> old QEMU, scsi=off
doesn't work (same as: old QEMU, scsi=on -> old QEMU, scsi=off)
- new QEMU, scsi=off -> old QEMU, scsi=off
broken by the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We will have to add another field to the virtio-blk configuration in
the next patch. Avoid a proliferation of arguments to virtio_blk_init.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move it from virtio_blk_exit_pci to virtio_blk_exit.
This is included here because the next patch removes proxy->block.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Linux really looks only at scsi->errors for SG_IO requests; it does
not look at the virtio request status at all. Because of this, when
a SG_IO request is failed early with virtio_blk_req_complete(req,
VIRTIO_BLK_S_UNSUPP), without writing hdr.status, it will look like
a success to the guest.
This is their bug, but we can make it safe for older guests now by
forcing scsi->errors to have a non-zero value whenever a request
has to be failed.
But if we fix the bug in the guest driver, we will have another problem
because QEMU returns VIRTIO_BLK_S_IOERR if the status is non-zero, and
Linux translates that to -EIO. Rather, the guest should succeed the
request and pass the non-zero status via the userspace-provided SG_IO
structure. So, remove the case where virtio_blk_handle_scsi can
return VIRTIO_BLK_S_IOERR.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Allow load_image_targphys to load files on systems with more than 2G of
emulated memory by changing the max_sz parameter from an int to an
uint64_t.
Reviewed-by: Andreas F=E4rber <afaerber@suse.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make use of the new vector notifier to track changes of the MSI-X
configuration of virtio PCI devices. On enabling events, we establish
the required virtual IRQ to MSI-X message route and link the signaling
eventfd file descriptor to this vIRQ line. That way, vhost-generated
interrupts can be directly delivered to an in-kernel MSI-X consumer like
the x86 APIC.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Analogously to msi_nr_vectors_allocated, add a service for MSI-X. Will
be used by the virtio-pci layer.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Automatically commit route changes after kvm_add_routing_entry and
kvm_irqchip_release_virq. There is no performance relevant use case for
which collecting multiple route changes is beneficial. This makes
kvm_irqchip_commit_routes an internal service which assert()s that the
corresponding IOCTL will always succeed.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will add kvm_irqchip_add_msi_route, so let's make the difference
clearer.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Vector notifiers shall be triggered by the MSI/MSI-X core whenever a
relevant configuration change is programmed by the guest. In case of
MSI-X, changes are reported when the effective mask (global &&
per-vector) alters its state. On unmask, the current vector
configuration is included in the event report. This allows users - e.g.
virtio-pci layer - to transfer this information to external MSI-X
routing subsystems - like vhost + KVM in-kernel irqchip.
This implementation only provides MSI-X support, but extension to MSI is
feasible and will be provided later on when adding support for KVM PCI
device assignment.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In preparation of firing vector notifiers on mask changes, call
msix_handle_mask_update also from msix_mask_all. So far, this will have
no real effect.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This helper will also be used by the upcoming config notifier.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There are no outside references to virtio_portio.
Add missing 'static' specifier.
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Initrd load address is too low, it conflicts with kernel load
address:
rom: requested regions overlap (rom phdr #0: /tmp/vmlinux-debian-6.0.4-sparc64. free=0x0000000000742519, addr=0x0000000000400000)
rom loading failed
Fix by making the initrd address variable, load initrd after kernel
image. Use 64 bit variables instead of longs or 32 bit types.
Tested-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: John V. Baboval <john.baboval@virtualcomputer.com>
Signed-off-by: Tom Goetz <tom.goetz@virtualcomputer.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
In the context of PV-on-HVM under Xen, the emulated nics are supposed to be
unplug before the guest drivers are initialized, when the guest write to a
specific IO port.
Without this patch, the guest end up with two nics with the same MAC, the
emulated nic and the PV nic.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
While for the "normal" case (called from blk_send_response_all())
decrementing requests_finished is correct, doing so in the parse error
case is wrong; requests_inflight needs to be decremented instead.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Use bdrv_aio_flush instead of bdrv_flush.
Make sure to call bdrv_aio_writev/readv after the presync bdrv_aio_flush is fully
completed and make sure to call the postsync bdrv_aio_flush after
bdrv_aio_writev/readv is fully completed.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
This patch removes a dead option.
The same can be achieved removing BDRV_O_NOCACHE and BDRV_O_CACHE_WB
from the flags passed to bdrv_open.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
PIT and PCSPK are emulated by the hypervisor so we don't need to emulate
them in Qemu: this patch prevents Qemu from waking up needlessly at
PIT_FREQ on Xen.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Catch writes to the MSI MMIO region in the KVM APIC and forward them to
the kernel. Provide the kernel support GSI routing, this allows to
enable MSI support also for in-kernel irqchip mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Push msi_supported enabling to the APIC implementations where we can
encapsulate the decision more cleanly, hiding the details from the
generic code.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Will be used for generating and distributing MSI messages, both in
emulation mode and under KVM.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* sweil/for-1.1:
qemu-doc: Use QEMU instead of qemu for product name
qemu-doc: Fix executable name in examples
qemu-doc: Add missing parameter in description of -D option
configure: Use QEMU instead of Qemu
fix some common typos
qemu-timer: Fix wrong error message
Since most property types do not have a parse property now, this was
broken. Fix it by looking at the setter instead.
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Andreas F=E4rber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Most important here is to update our internal endpoint state so we know
the endpoint isn't in halted state any more. Without this usb-host
tries to clear halt again with the next data transfer submitted. Doing
this twice is (a) not correct and (b) confuses some usb devices,
rendering them non-functional in the guest.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These were identified using: http://github.com/lyda/misspell-check
and run like this to create a bourne shell script using GNU sed's
-i option:
git ls-files|grep -vF .bin | misspellings -f - |grep -v '^ERROR:' |perl \
-pe 's/^(.*?)\[(\d+)\]: (\w+) -> "(.*?)"$/sed -i '\''${2}s!$3!$4!'\'' $1/'
Manually eliding the FP, "rela->real" and resolving "addres" to
address (not "adders") we get this:
sed -i '450s!thru!through!' Changelog
sed -i '260s!neccessary!necessary!' coroutine-sigaltstack.c
sed -i '54s!miniscule!minuscule!' disas.c
sed -i '1094s!thru!through!' hw/usb/hcd-ehci.c
sed -i '1095s!thru!through!' hw/usb/hcd-ehci.c
sed -i '21s!unecessary!unnecessary!' qapi-schema-guest.json
sed -i '307s!explictly!explicitly!' qemu-ga.c
sed -i '490s!preceeding!preceding!' qga/commands-posix.c
sed -i '792s!addres!address!' qga/commands-posix.c
sed -i '6s!beeing!being!' tests/tcg/test-mmap.c
Also, manually fix "arithmentic", spotted by Peter Maydell:
sed -i 's!arithmentic!arithmetic!' coroutine-sigaltstack.c
Signed-off-by: Jim Meyering <meyering@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
We have the following simplified callgraph in mips_fulong2e_init():
cpu_init() => cpu_mips_init()
object_new()
mips_cpu_initfn()
cpu_exec_init()
register_savevm(NULL, "cpu", cpu_index, CPU_SAVE_VERSION,
cpu_save, cpu_load, env)
register_savevm(NULL, "cpu", 0, 3, cpu_save, cpu_load, env)
CPU_SAVE_VERSION is defined as 3 in target-mips/cpu.h.
fulong2e instantiates one CPU, so its cpu_index is 0.
Thus the two are fully identical.
Therefore just remove the second call in fulong2e.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[AF: Extend explanation in commit message]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This was erroneously dropped in d6c730086c
(pc: reduce duplication in compat machine types).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
ptr properties have neither a get/set or a print/parse which means that when
they're added they aren't treated as static or legacy properties.
Just assume properties like this are legacy properties and treat them as such.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Otherwise, non-string properties without a legacy counterpart are missed.
Also fix error propagation in object_property_print() itself.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Similarly to PCI interrupt mappings, the OBIO ones have to be initialized.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* kwolf/for-anthony:
fdc: simplify media change handling
qcow2: lock on prealloc
block: make bdrv_create adopt coroutine
qcow2: Limit COW to where it's needed
sheepdog: switch to writethrough mode if cluster doesn't support flush
* bonzini/scsi-next:
scsi: Add assertion for use-after-free errors
scsi: remove useless debug messages
scsi: set VALID bit to 0 in fixed format sense data
scsi: do not require a minimum allocation length for REQUEST SENSE
scsi: do not require a minimum allocation length for INQUIRY
scsi: parse 16-byte tape CDBs
scsi: do not report bogus overruns for commands in the 0x00-0x1F range
scsi-disk: add dpofua property
scsi: change "removable" field to host many features
scsi: Specify the xfer direction for UNMAP and ATA_PASSTHROUGH commands
scsi: fix WRITE SAME transfer length and direction
scsi: fix refcounting for reads
scsi: prevent data transfer overflow
ISCSI: Add support for thin-provisioning via discard/UNMAP and bigger LUNs
Commit afe0a59535 added byte reads for TxStatus/TxAddr, but
broke 32-bit reads; the mask generation
(1 << (8 * size)) - 1
is unspecified in C for size >= sizeof(int), and in fact returns 0
on x86.
Fix by using a larger type.
Fixes (at least) Fedora 9 i386 with -machine kernel_irqchip=on. I
didn't see it with the qemu APIC implementation; may be due to timing
or (more likely) a tester error.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This also (partly) fixes IBM OS/2 Warp 4.0 floppy installation, where
not all floppies have the same format (2x80x18 for the first ones,
2x80x23 for the next ones).
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The Linux AC97 driver tests this bit to decide wether or not to show
an External amplifier toggle control.
This patch was also tested with a Windows XP guest without any issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
The Linux ac97 drivers does a number of register read/write tests to
see how much resolution a volume control actually has.
This patch takes this into account by masking out any bits written to
a volume control reg which should not be there according to the spec.
After this the Linux ac97 driver correctly uses a range of 0 - 0x1f for
the PCM out volume, as stated in the spec, and we can fix the FIXME
in update_combined_volume_out().
This patch was also tested with a Windows XP guest without any issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
After commit 19677a380a:
"hw/ac97: add support for volume control"
We are (correctly) using AC97_Record_Gain_Mute and not AC97_Line_In_Volume_Mute
for recording volume, but various places in hw/ac97 were still assumimg that
we are using AC97_Line_In_Volume_Mute for record volume control, this patch
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
The Linux ac97 driver tries to see if optional things like video input
volume control are available in 2 ways:
1) See if the mute bit is set after reset, if it is no further tests are done
2) If the mute bit is not set it does a write/read test of the mute bit
This patch changes our ac97 to conform to what the Linux driver expects, it
initializes registers for things which we don't emulate to 0 (so the mute bit
is not set) and makes them read only.
This causes Linux to now longer show the following (functionless)
controls in alsamixer:
Master Mono vol + mute
3d Control toggle
PCM out pre / post 3d select
Surround toggle
CD vol + mute
Mic vol + mute
Mic boost toggle
Mic mic1 / mic2 select
Video vol + mute
Phone vol + mute
Beep mono vol + mute
Aux vol + mute
Mono "output mic" / "mix" select
Sigmatel 4 speaker stereo toggle
Sigmatel ADC 6Db att toggle
Sigmatel DAC 6Db att toggle
This patch was also tested with a Windows XP guest and there it also makes
a number of functionless mixer controls go away.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
The QEMU emulation which is currently used with Raspberry PI images
(qemu-system-arm -M versatilepb ...) accesses memory which was freed.
Valgrind output (extract):
==17857== Invalid write of size 4
==17857== at 0x24EB06: scsi_req_unref (scsi-bus.c:1273)
==17857== by 0x24FFAE: scsi_read_complete (scsi-disk.c:277)
==17857== by 0x152ACC: bdrv_co_em_bh (block.c:3363)
==17857== by 0x13D49C: qemu_bh_poll (async.c:71)
==17857== by 0x211A8C: main_loop_wait (main-loop.c:503)
==17857== by 0x207954: main_loop (vl.c:1555)
==17857== by 0x20E9C9: main (vl.c:3653)
==17857== Address 0x1c54383c is 12 bytes inside a block of size 260 free'd
==17857== at 0x4824B3A: free (vg_replace_malloc.c:366)
==17857== by 0x20ADFA: free_and_trace (vl.c:2250)
==17857== by 0x4899FC5: g_free (in /lib/libglib-2.0.so.0.2400.1)
==17857== by 0x24EB3B: scsi_req_unref (scsi-bus.c:1277)
==17857== by 0x24F003: scsi_req_complete (scsi-bus.c:1383)
==17857== by 0x25022A: scsi_read_data (scsi-disk.c:334)
==17857== by 0x24EB9F: scsi_req_continue (scsi-bus.c:1289)
==17857== by 0x1C7787: lsi_do_dma (lsi53c895a.c:575)
==17857== by 0x1C8CDA: lsi_execute_script (lsi53c895a.c:1147)
==17857== by 0x1C74EA: lsi_resume_script (lsi53c895a.c:510)
==17857== by 0x1C7ECD: lsi_transfer_data (lsi53c895a.c:746)
==17857== by 0x24EC90: scsi_req_data (scsi-bus.c:1307)
(There are some more similar messages.)
This patch adds an assertion which also detects those errors:
Calling scsi_req_unref is not allowed when the previous call
of that function has decremented refcount to 0, because in this
case req was freed.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Optional inquiry information is declared obsolete in the latest versions
of the standard; invalid CDBs or unsupported VPD pages are supported
can be diagnosed with trace_scsi_inquiry.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The requirements on the REQUEST SENSE buffer size are not in my copy of SPC
(SPC-4 r27) and not observed by LIO. Rip them out.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The requirements on the INQUIRY buffer size are not in my copy of SPC
(SPC-4 r27) and not observed by LIO. Rip them out.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The transfer length for these commands is different from the transfer
length of the corresponding disk commands, so parse it specially.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Interpreting cdb[4] == 0 as a request to transfer 256 blocks is only
needed for READ_6 and WRITE_6. No other command in that range needs
that special-casing, and the resulting overrun breaks scsi-testsuite's
attempt to use command 2 as a known-invalid command.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linux expects REQ_FUA to be advertised only if WRITE+FUA is faster than
WRITE+SYNCHRONIZE CACHE, so we should not set the DPOFUA bit. However,
it is useful to have it for testing purposes, so add a qdev property to
set it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is pointless to add a uint32_t field for every new feature.
Since we will need a new feature soon, convert accesses to "removable"
to look at bit 0 only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
scsi_cmd_xfer_mode() is used to specify the xfer direction for SCSI
commands that come in from the guest. If the direction is set incorrectly
this will eventually cause QEMU to kernel-panic the guest.
Add UNMAP and ATAPASSTHROUGH as commands that send data to the device.
Without this change, recent kernels will send both UNMAP as well
as ATAPASSTHROUGH commands to any /dev/sg* device, which due to the
incorrect xfer direction very quickly causes the guest kernel to crash.
Example causing a crash without the patch applied:
./x86_64-softmmu/qemu-system-x86_64 -m 1024 -enable-kvm -cdrom linuxmint-12-gnome-dvd-64bit.iso -drive file=/dev/sg4,if=scsi,bus=0,unit=6
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Recently introduced FUA support also gave us a use-after-free
of the BlockAcctCookie within a SCSIDiskReq, due to unbalanced
reference counting.
The patch fixes this by making scsi_do_read look like a combination
of scsi_*_complete + scsi_*_data. It does both a ref (like
scsi_read_data) and an unref (like scsi_flush_complete).
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Valgrind reported this memory leak which occured a few times.
Test scenario:
qemu-system-i386 (no arguments), only BIOS started, terminate with
monitor command (quit).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Valgrind reported this memory leak which occured very often.
Test scenario:
qemu-system-i386 (no arguments), only BIOS started, terminate with
monitor command (quit).
v2:
Use error_free instead of g_free (hint from Andreas Färber, thanks).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Andreas Färber <afaerber@suse.de>
When using Windows 8 with an AHCI disk drive, it issues a blue screen.
The reason is that WIN_SECURITY_FREEZE_LOCK / CFA_WEAR_LEVEL is not
supported by our ATA implementation, but Windows expects it to be there.
Since without security stuff implemented, the lock would be a nop anyway
and CFA_WEAR_LEVEL already is treated as a nop, let's just allow the cmd
for HD drives as well. That way Windows is happy.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* agraf/s390-for-upstream:
s390: reset avail and used index on reboot
S390: dont call system_shutdown on disabled wait
S390: remove default cdrom, sd-card and floppy support
S390: support reboot for kvm on s390
S390: reboot: reset device pages on reboot
S390: fix error handling on kernel and initrd failures
S390: fix kernel_commandline handling
The default case in function spin_read should never be reached,
therefore the old code used assert(0) to abort QEMU.
This does not work when QEMU is compiled with macro NDEBUG defined.
In this case (and also when the compiler does not know that assert
never returns), there is a compiler warning because of the missing
return value.
Using hw_error allows an improved error message and aborts always.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
[agraf: use __func__]
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit ed120055c7 (Implement PAPR VPA
functions for pSeries shared processor partitions) introduced the
deregister_dtl() function and typo "emv" as name of its argument.
This went unnoticed because the code in that function can access the
global variable "env" so that no build failure resulted.
Fix the argument to read "env". Resolves LP#986241.
Signed-off-by: Peter Portante <peter.portante@redhat.com>
Acked-by: Andreas Färber <afaerber@suse.de>
[agraf: fixed typo in commit message]
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the pseries PCI code uses a somewhat strange scheme of PCI irq
allocation - one per slot up to a maximum that's greater than the usual 4.
This scheme more or less worked, because we were able to tell the guest the
irq mapping in the device tree, however it's a bit odd and may break
assumptions in the future. Worse, the array used to construct the dev
tree interrupt map was mis-sized, we got away with it only because it
happened that our SPAPR_PCI_NUM_LSI value was greater than 7.
This patch changes the pseries PCI code to use the same interrupt swizzling
scheme as is standardized for PCI to PCI bridges. This makes for better
consistency, deals better with any devices which use multiple interrupt
pins and will make life easier in the future when we add passthrough of
what may be either a host bridge or a PCI to PCI bridge. This won't break
existing guests, because they don't assume a particular mapping scheme for
host bridges, but just follow what we tell them in the device tree (also
updated to match, of course). This patch also fixes the allocation of the
irq map.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR virtual IO (VIO) devices require a unique, but otherwise arbitrary,
"address" used as a token to the hypercalls which manipulate them.
Currently the pseries machine code does an ok job of allocating these
addresses when the legacy -net nic / -serial and so forth options are used
but will fail to allocate them properly when using -device.
Specifically, you can use -device if all addresses are explicitly assigned.
Without explicit assignment, only one VIO device of each type (network,
console, SCSI) will be assigned properly, any further ones will attempt
to take the same address leading to a fatal error.
This patch fixes the situation by adding a proper address allocator to the
VIO "bus" code. This is used both by -device and the legacy options and
default devices. Addresses can still be explicitly assigned with -device
options if desired.
This patch changes the (guest visible) numbering of VIO devices, but since
their addresses are discovered using the device tree and already differ
from the numbering found on existing PowerVM systems, this does not break
compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Initial Mapping creation for secondary CPU in SMP was missing new MMU API.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
reset the guest vring avail/used idx fields, otherwise it's possible
that old values remain in memory which would cause a reboot to fail
with a "Guest moved used index" message
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch simply disables CDROM, SD card and floppy support for the
s390 virtio machine. Without this patch, a default CDROM drive would
get added which has currently no backing on s390.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch fixes reboot on s390 by resetting the device
page on reboot.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
If the user specifies a non-existing or non-accessable kernel or initrd
qemu does not fail, instead it ipls into the system, which then falls
into a program check loop due to the zeroed memory with no kernel.
Lets add some sanity checks.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current handling of kernel parameters is broken. The pointer
is always valid, even if no -kernel or -append is specified.
We must check if the kernel rom address is valid instead,
otherwise qemu might segfault.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Initially, vga_get_text_resolution returns a text resolution of 1 x 1
(vga register values are 0).
This is visible during MIPS Malta boot with SDL. It also occurs with the
i386 or x86_64 system emulation when it runs in single step mode:
QEMU changes the size of the SDL window to the smallest possible value
which is supported by the window manager. As this is not the calculated
size, QEMU switches to scaled mode. When the BIOS or the VGA driver sets
the normal text resolution, the window stays small and displays
microscopic characters.
Ignoring text resolutions of 1 x 1 or less avoids these problems.
A similar workaround already exists for too large resolutions.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Register is one byte-wide (as per specification), so there is no need
to specify endianness.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[AF: Limit access validity to size 1]
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Speaker init has been added in 506b7ddf88,
but audio subsystem init was missing.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Keep the PC values as defaults but allow to override them for PReP.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
This fixes a crash in PReP emulation when using DMA controller to access
floppy drive.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
* 'target-arm.for-upstream' of git://git.linaro.org/people/pmaydell/qemu-arm:
target-arm: Make SETEND respect bswap_code (BE8) setting
target-arm: Move A9 config_base_address reset value to ARMCPU
target-arm: Change cpu_arm_init() return type to ARMCPU
Move the A9 config_base_address cp15 register reset value to
ARMCPU. This should become a QOM property so that the Highbank
board can set it without having to pull in cpu-qom.h, but at
least this avoids the implicit dependency on reset ordering
that the previous workaround had.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
* kraxel/usb.49:
usb-uhci: update irq line on reset
usb: add serial number generator
usb-redir: Not finding an async urb id is not an error
usb-redir: Reset device address and speed on disconnect
usb-redir: An interface count of 0 is a valid value
usb-xhci: fix bit test
usb-xhci: Use PCI DMA helper functions
usb-host: fix zero-length packets
usb-host: don't dereference invalid iovecs
usb-storage: fix request canceling
usb-ehci: Ensure frindex writes leave a valid frindex value
usb-ehci: add missing usb_packet_init() call
usb-ehci: remove hack
* mst/tags/for_anthony:
e1000: set E1000_ICR_INT_ASSERTED only for 8257x
e1000: link auto-negotiation emulation
e1000: introduce bit for debugging PHY emulation
e1000: introduce helpers to manipulate link status
e1000: PHY loopback mode support
e1000: conditionally raise irq at the end of MDI cycle
e1000: introduce bits of PHY control register
eepro100: Fix multicast regression
virtio: order index/descriptor reads
virtio: add missing mb() on enable notification
virtio: add missing mb() on notification
e1000: move reset function earlier in file
We're not actually calling qdev_init for the pc-sysfw device. Since we create
the canonical path during realize, this was causing an assert to trigger when
attempting to read a link pointing to pc-sysfw.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
uhci_reset() clears irq mask and irq status registers, but doesn't
update the irq line. Which may result in suspious IRQs after uhci
reset. Fix it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds a function which creates unique serial numbers for usb
devices and puts it into use. Windows guests tend to become unhappy if
they find two identical usb devices in the system. Effects range from
non-functional devices (with yellow exclamation mark in device manager)
to BSODs. Handing out unique serial numbers to devices fixes this.
With this patch applied almost all emulated devices get a generated,
unique serial number. There are two exceptions:
* usb-storage devices will prefer a user-specified serial number
and will only get a generated number in case the serial property
is unset.
* usb-hid devices keep the fixed serial number "42" as it is used
to signal "remote wakeup actually works".
See commit 7b074a22da
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We clear our pending async urb list on device disconnect and we may still
receive "packet complete" packets from our peer after this, which will then
refer to packet ids no longer in our list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Without this disconnected devices look like the last redirected device
in the monitor in "info usb".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
An interface-count of 0 happens when a device is in unconfigured state when
it gets redirected. So we should not use 0 to detect not having received
interface info from our peer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Shortly before 1.0, we added helper functions / wrappers for doing PCI DMA
from individual devices. This makes what's going on clearer and means that
when we add IOMMU support somewhere in the future, only the general PCI
code will have to change, not every device that uses PCI DMA.
However, usb-xhci is not using these wrappers, despite being a PCI only
device. This patch remedies the situation, using the pci dma functions
instead of direct calls to cpu_physical_memory_{read,write}(). Likewise
address parameters for DMA are changed to dma_addr_t instead of
target_phys_addr_t.
[ kraxel: removed #ifdefs ]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-host optimizes away zero-length packets by not entering the
processing loop at all. Which isn't correct, we should submit a
zero-length urb to the host devicein that case. This patch makes
sure we run the processing loop at least once.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-host assumes the first iovec element is always valid.
In case of a zero-length packet this isn't true though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Little fix for usb packet handling on i/o cancelation. The
usb packet pointer (s->packet) is cleared at the wrong place:
The scsi request cancel handler does it. When a usb packet
is canceled the usb-storage emulation canceles the scsi request
if present. In most cases there is one, so usually s->packet
is cleared as needed even with the code sitting at the wrong
place.
If there is no scsi request in flight s->packet is not cleared
though. The usb-storage emulation will then try to complete an
usb packet which is not in flight any more and thereby trigger
an assert() in the usb core.
Fix this by clearing s->packet at the correct place, which is
the usb packet cancel header.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
frindex is a 14 bits counter, so bits 31-14 should always be 0, and
after the commit titled "usb-ehci: frindex always is a 14 bits counter"
we rely on frindex always being a multiple of 8. I've not seen this in
practice, but theoretically a guest can write a value >= 0x4000 or a value
which is not a multiple of 8 value to frindex, this patch ensures that
things will still work when that happens.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To answer the question in the comment removed by this patch: I think
this was needed because several places in the ehci emulation did not
check the T bit of link entries correctly and thus might have followed
invalid references. See commit 2a5ff735dc
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Our hda codecs exist in two variants: With CONFIG_MIXEMU=y they expose
amplifiers for volume control to the guest, with CONFIG_MIXEMU=n they
don't.
This patch changes the codec ids, they are different now for these two
cases. This makes sure windows guests will notice the difference.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
It's identical to the hda-duplex codec, except that it advertises the
input as microphone instead of line-in and the output as speaker instead
of line-out. Some guest apps (microsoft netmeeting being one) are picky
when it comes to selecting the recording source and don't accept
line-in, so give them what they expect.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
When a guest driver resets the virtio status to not ready, or when qemu
is reset, reset all ports' guest_connected bit and let port users know
of this event if they have the guest_close() callback registered.
Reviewed-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
guest_connected should be false before guest driver initialization, and
true after, both for multiport aware and non multiport aware drivers.
Don't set it before the guest_features are available; instead use
set_status which is called by io to VIRTIO_PCI_STATUS with
VIRTIO_CONFIG_S_DRIVER_OK by even older non multiport drivers.
[Amit: Add comment, tweak summary, only set guest_connected and not
reset it as a side-effect.]
Signed-off-by: Alon Levy <alevy@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
E1000_ICR_INT_ASSERTED were introduced only for 8257x, so we need to
check the E1000_DEVID before setting this bit in ICS.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Indeed, there's nothing else except for the time spent on the
negotiation needs to be emulated. This is needed for resuming windows
guest from hibernation, as without a proper delay, qemu would send the
packet too early ( guest even does not have a proper intr handler),
which could lead windows guest hang.
This patch first introduces an array of function pointers to make it
possible to emulate per-register write behavior. Then traps the
PHY_CTRL register write and when guest want to restart the link auto
negotiation, we would down the link and mark the auto negotiation in
progress in PHY_STATUS register. After time, a timer with 500 ms (
which is the minimum timeout of auto-negotation specified in 802.3
spec). The link would be up when timer expired.
Test with resuming windows guest plus flood ping and linux ethtool
linkstatus test.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces helpers to change link status bit for phy/mac
register. This would help to reduce code duplication and would be used
by following patches.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The missing of loopback mode prevent the running of self diagnosis
program in guest. This patch adds this support.
After this patch, loopback test of ethtool were passed in guest.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to the spec:
"When set to 1b by software, it causes an Interrupt to be
asserted to indicate the end of an MDI cycle."
We need check the Interrupt Enable bit and raise irq only when it is
set.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 7fc8d918b9 removed code from
eepro100.c and replaced it by different code: the code in net.c
returns bits 31...26, but eepro100 needs bits 7...2.
This patch partially reverts 7fc8d918b9.
To avoid future problems, I renamed the function and changed the comment.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio has the equivalent of:
if (vq->last_avail_index != vring_avail_idx(vq)) {
read descriptor head at vq->last_avail_index;
}
In theory, processor can reorder descriptor head
read to happen speculatively before the index read.
this would trigger the following race:
host descriptor head read <- reads invalid head from ring
guest writes valid descriptor head
guest writes avail index
host avail index read <- observes valid index
as a result host will use an invalid head value.
This was not observed in the field by me but after
the experience with the previous two races
I think it is prudent to address this theoretical race condition.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes an issue dual to the one fixed by
patch 'virtio: add missing mb() on notification'
and applies on top.
In this case, to enable vq kick to exit to host,
qemu writes out used flag then reads the
avail index. if these are reordered we get a race:
host avail index read: ring is empty
guest avail index write
guest flag read: exit disabled
host used flag write: enable exit
which results in a lost exit: host will never be notified about the
avail index update. Again, happens in the field but only seems to
trigger on some specific hardware.
Insert an smp_mb barrier operation to ensure the correct ordering.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
During normal operation, virtio first writes a used index
and then checks whether it should interrupt the guest
by reading guest avail index/flag values.
Guest does the reverse: writes the index/flag,
then checks the used ring.
The ordering is important: if host avail flag read bypasses the used
index write, we could in effect get this timing:
host avail flag read
guest enable interrupts: avail flag write
guest check used ring: ring is empty
host used index write
which results in a lost interrupt: guest will never be notified
about the used ring update.
This actually can happen when using kvm with an io thread,
such that the guest vcpu and qemu run on different host cpus,
and this has actually been observed in the field
(but only seems to trigger on very specific processor types)
with userspace virtio: vhost has the necessary smp_mb()
in place to prevent the regordering, so the same workload stalls
forever waiting for an interrupt with vhost=off but works
fine with vhost=on.
Insert an smp_mb barrier operation in userspace virtio to
ensure the correct ordering.
Applying this patch fixed the race condition we have observed.
Tested on x86_64. I checked the code generated by the new macro
for i386 and ppc but didn't run virtio.
Note: mb could in theory be implemented by __sync_synchronize, but this
would make us hit old GCC bugs. Besides old GCC
not implementing __sync_synchronize at all, there were bugs
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=36793
in this functionality as recently as in 4.3.
As we need asm for rmb,wmb anyway, it's just as well to
use it for mb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If a guest sets very short timeouts, and asks for a timer to be reloaded on
timeout, QEMU can go to 100%CPU utilisation and become unresponsive,
as it is spending all its time generating timeout interrupts. On real
hardware this doesn't matter, as the interrupts are just coalesced,
and the effect is to have the interrupt asserted all the time.
This patch is a band-aid, that prevents timeouts less than 10
microseconds from being set. 10 microseconds is a limit that was
determined empirically on a variety of machines as the shortest that
allowed QEMU to pick up a control-a c sequence to get at the monitor.
Reported-by: Anna Lyons <anna.lyons@nicta.com.au>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Specify the root to search from as argument. This avoids hardcoding
"/machine" in some places and makes it more flexible.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kwolf/for-anthony: (38 commits)
qemu-iotests: Fix test 031 for qcow2 v3 support
qemu-iotests: Add -o and make v3 the default for qcow2
qcow2: Zero write support
qemu-iotests: Test backing file COW with zero clusters
qemu-iotests: add a simple test for write_zeroes
qcow2: Support for feature table header extension
qcow2: Support reading zero clusters
qcow2: Version 3 images
qcow2: Ignore reserved bits in check_refcounts
qcow2: Ignore reserved bits in refcount table entries
qcow2: Simplify count_cow_clusters
qcow2: Refactor qcow2_free_any_clusters
qcow2: Ignore reserved bits in L1/L2 entries
qcow2: Fail write_compressed when overwriting data
qcow2: Ignore reserved bits in count_contiguous_clusters()
qcow2: Ignore reserved bits in get_cluster_offset
qcow2: Save disk size in snapshot header
Specification for qcow2 version 3
qcow2: Fix refcount block allocation during qcow2_alloc_cluster_at()
iotests: Resolve test failures caused by hostname
...
Fix BCD mask for date. The most visible effect of this patch is
Solaris 2.5.1 doesn't hang at boot if the day of month is >21.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* origin/master: (27 commits)
target-arm: Move reset handling to arm_cpu_reset
target-arm: Drop cpu_reset_model_id()
target-arm: Move cache ID register setup to cpu specific init fns
target-arm: Move OMAP cp15_i_{max,min} reset to cpu_state_reset
target-arm: Move feature register setup to per-CPU init fns
target-arm: Move iWMMXT wCID reset to cpu_state_reset
target-arm: Drop JTAG_ID documentation
target-arm: Move SCTLR reset value setup to per cpu init fns
target-arm: Move CTR setup to per cpu init fns
target-arm: Move MVFR* setup to per cpu init fns
target-arm: Move FPSID config to cpu init fns
target-arm: Move feature bit settings to CPU init fns
target-arm: Add QOM subclasses for each ARM cpu implementation
target-arm: remind to keep arm features in sync with linux-user/elfload.c
tci: GETPC() macro must return an uintptr_t
gdbstub: Synchronize CPU state unconditionally in gdb_set_cpu_pc
softfloat: make USE_SOFTFLOAT_STRUCT_TYPES compile
target-xtensa: add tests for LOOPNEZ and LOOPGTZ
target-xtensa: fix LOOPNEZ/LOOPGTZ translation
qtest: add m48t59 tests for Sparc
...
* stefanha/trivial-patches:
Add .gitignore for tests/
e1000: Fix spelling (segmentaion -> segmentation) in debug output
spice-qemu-char.c: Show what name is unsupported
pflash_cfi01: remove redundant line
qxl: Add missing GCC_FMT_ATTR and fix format specifier
fix block_job_set_speed name in documentation
error.c: don't return value for void function
* bonzini/scsi-next:
scsi: add SANITIZE command
SCSI emulation: should tell the guest that we actually support thin provisioning
SCSI emulation: Support unmap via WRITE_SAME_10.
scsi: advertise DPOFUA
scsi: small refactoring of MMC mode-sense
scsi: support FUA on reads
scsi: add a started field to SCSIDiskReq
scsi: force unit access on VERIFY
scsi: add support for FUA on writes
scsi: move scsi_flush_complete around
scsi: make code more homogeneous in AIO callback functions
scsi: add missing test for cancelled request
virtio-scsi: add multiqueue capability
virtio: add virtio_queue_get_id
virtio-scsi: prepare migration format for multiqueue
scsi: fix memory leak
On reset of the mpcore timer/watchdog block we need to
delete the qemu_timer in case it was running.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The versatile i2c controller implementation was separated to
its own file called versatile_i2c.c. This is done as a preparation
for adding i2c support to the versatilepb board.
Signed-off-by: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This was reported by https://bugs.launchpad.net/qemu/+bug/984476.
I also changed the case for 'error'.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
val is an uint64_t, therefore %d was not correct.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
[Actually, we should report it only if discard_granularity is nonzero.
Older SBC drafts assigned 0 to thin provisioning and 1 to thick
(resource-provisioned, they call it). Newer drafts assign respectively
1 and 2 - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This was added in SBC r26 in place of the reserved bits that were
present up to that version.
It is the same as WRITE_SAME_16 as far as QEMU is concerned.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The IDE PIO write sector code path uses bdrv_write() and hence can make
the guest unresponsive while the I/O request is in progress. This patch
converts ide_sector_write() to use bdrv_aio_writev() by using the
BUSY_STAT bit to tell the guest that the request is in progress.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Tested-by: Richard Davies <richard@arachsys.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The IDE PIO interface currently uses bdrv_read() to perform reads
synchronously. Synchronous I/O in the vcpu thread is bad because it
prevents the guest from executing code - it makes the guest
unresponsive.
This patch converts IDE PIO to use bdrv_aio_readv(). We simply need to
use the BUSY_STAT status so the guest knows to wait while we are busy.
The only external user of ide_sector_read() is restart behavior on I/O
errors and it is not affected by this change. We still need to restart
I/O in the same way.
Migration is also unaffected if I understand the code correctly. We
continue to use the same transfer function and the BUSY_STAT status
should never be migrated since we flush I/O before migrating device
state.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Tested-by: Richard Davies <richard@arachsys.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To force unit access, add a flush operation after the actual write.
WRITE AND VERIFY commands always flush according to SBC, so do it
even though we do not perform the reread.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
First scsi_flush_complete, like scsi_dma_complete, is always called with
an active AIOCB.
Second, always test for "ret < 0" to check for errors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adding multiqueue is as simple as creating more than one virtqueues,
and saving the queue number for each request.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Serializing virtio-scsi requests needs a simple way to get from a
VirtQueue to the number of the queue. The virtio_queue_get_id
provides this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to restore requests correctly from a multitude of virtqueues,
we need to store the id of the request queue that each request came
from.
Do this even for single-queue, by storing a hard-coded zero, to
simplify future implementation of multiqueue.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
scsibus_get_dev_path is leaking id if it is not NULL. Fix it.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* origin/master:
Allow controlling volume with PulseAudio backend
configure: pa_simple is not needed anymore
Do not use pa_simple PulseAudio API
audio/spice: add support for volume control
hw/ac97: add support for volume control
hw/ac97: the volume mask is not only 0x1f
hw/ac97: remove USE_MIXER code
audio: don't apply volume effect if backend has VOICE_VOLUME_CAP
audio: add VOICE_VOLUME ctl
Notify any listeners such as vnc that the displaysurface has been
changed, otherwise they will segfault when first accessing the freed old
displaysurface data.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The addition of those values caused a regression where not specifying
any value for the vram bar size would result in a 4096 _byte_ surface
area. This is ok for the windows driver but causes the X driver to be
unusable. Also, it's a regression. This patch returns the default
behavior of having a 64 megabyte vram BAR.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xc_hvm_inject_msi is only available on Xen >= 4.2: add a dummy
compatibility function for Xen < 4.2.
Also enable msi support only on Xen >= 4.2.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Combine output volume with Master and PCM registers values.
Use default values in mixer_reset ().
Set volume on post-load to update backend values.
v4,v5:
- fix some code style
Signed-off-by: Marc-Andr? Lureau <marcandre.lureau@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
It's a case by case (see Table 66. AC ?97 Baseline Audio Register Map)
Signed-off-by: Marc-Andr? Lureau <marcandre.lureau@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
That code doesn't compile. The interesting bits for volume control are
going to be rewritten in the following patch.
Signed-off-by: Marc-Andr? Lureau <marcandre.lureau@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
Not sure what the purpose of the assert() was, in any case it is bogous.
We can arrive there if transfer descriptors passed to us from the guest
failed to pass sanity checks, i.e. it is guest-triggerable. We deal
with that case by resetting the host controller. Everything is ok, no
need to throw a core dump here.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Also cleanup (reset) our device state when we reject a device due to a
speed mismatch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The sofv value only ever gets a value assigned and is never used (read)
anywhere, so we can just drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch carries a complete rewrite of the usb descriptor parser.
Changes / improvements:
* We are using the USBDescriptor struct instead of hard-coded offsets
now to access descriptor data.
* (debug) printfs are all gone, tracepoints have been added instead.
* We don't try (and fail) to skip over unneeded descriptors. We parse
them all one by one. We keep track of which configuration, interface
and altsetting we are looking at and use this information to figure
which desciptors are in use and which we can ignore.
* On parse errors we clear all endpoint information, which will
disallow any communication with the device, except control endpoint
messages. This makes sure we don't end up with a silly device state
where half of the endpoints got enabled and the other half was left
disabled.
* Some sanity checks have been added.
The new parser is more robust and also leaves complete device
information in the trace log if you enable the ush_host_parse_*
tracepoints.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds a new type for the binary representation of usb
descriptors. It is put into use for the descriptor generator code
where the struct replaces the hard-coded offsets.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
