Follow the QEMU convention of naming MachineState pointers as 'ms' by
renaming the instance in create_fdt() where we're calling it 'mc'.
Cc: Paul Burton <paulburton@kernel.org>
Cc: Aleksandar Rikalo <aleksandar.rikalo@syrmia.com>
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20230111172133.334735-1-dbarboza@ventanamicro.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tracking dependencies via Kconfig seems much cleaner.
Note that PIIX4 already depends on ACPI_PIIX4.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230109172347.1830-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
pci_map_irq_fn's in general seem to be board-specific, and PIIX4's
pci_slot_get_pirq() in particular seems very Malta-specific. So move the
latter to malta.c to 1/ keep the board logic in one place and 2/ avoid
PIIX4 to make assumptions about its board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This support was limited to the Malta board, drop it.
I do not have a machine that can run VZ KVM, so I am assuming
that it works for -M malta as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221221091718.71844-1-philmd@linaro.org>
Linux kernel expects the northbridge & southbridge chipsets
configured by the BIOS firmware. We emulate that by writing
a tiny bootloader code in write_bootloader().
Upon introduction in commit 5c2b87e34d ("PIIX4 support"),
the PIIX4 configuration space included values specific to
the Malta board.
Set the Malta-specific IRQ routing values in the embedded
bootloader, so the next commit can remove the Malta specific
bits from the PIIX4 PCI-ISA bridge and make it generic
(matching the real hardware).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-3-philmd@linaro.org>
The PIIX4 PCI-ISA bridge function is always located at 10:0.
Since we want to re-use its address, add the PIIX4_PCI_DEVFN
definition.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221027204720.33611-2-philmd@linaro.org>
Merge common code shared between write_bootloader() and
write_bootloader_nanomips() into bl_setup_gt64120_jump_kernel().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-12-philmd@linaro.org>
Part 5/5: Convert jumping to kernel
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-11-philmd@linaro.org>
Part 4/5: Convert GT64120 ISD base address setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-10-philmd@linaro.org>
Part 3/5: Convert PCI0 I/O BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-9-philmd@linaro.org>
Part 2/5: Convert PCI0 MEM0 BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-8-philmd@linaro.org>
Similarly to how commit 0c8427baf0 ("hw/mips/malta: Use bootloader
helper to set BAR registers") converted write_bootloader(), convert
the equivalent write_bootloader_nanomips(), allowing us to modify
the bootloader code more easily in the future.
Part 1/5: Convert PCI0 MEM1 BAR setup
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-7-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-6-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-5-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-4-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211204533.85359-3-philmd@linaro.org>
It is irrelevant to the API what the buffers to fill are made of.
In particular, some MIPS ISA have 16-bit wide instructions.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221211204533.85359-2-philmd@linaro.org>
The GT-64120 is a north-bridge, and it is not MIPS specific.
Move it with the other north-bridge devices.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221209151533.69516-8-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The single machine using this device explicitly sets its
endianness. We don't need to set a default. This allow us
to remove the target specificity from the build system.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20221209151533.69516-7-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Propagate the controller endianess from the machine, setting
the "cpu-little-endian" property.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221209151533.69516-6-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This device does not have to be TARGET-dependent.
Add a 'cpu_big_endian' property which sets the byte-swapping
options if required.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221220113436.14299-5-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221220113436.14299-4-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Per the comment in the Malta board, the [0x0000.0000-0x2000.0000]
range is decoded by the GT64120, so move the "empty_slot" there.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221209151533.69516-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221209151533.69516-2-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
GT64120's PCI endianness swapping works on little-endian hosts,
but doesn't on big-endian ones. Instead of complicating how
CFGADDR/CFGDATA registers deal with endianness, use the existing
MemoryRegionOps from hw/pci/pci_host.c. Doing so also reduce the
access to internal PCI_HOST_BRIDGE fields.
Map the PCI_HOST_BRIDGE MemoryRegionOps into the corresponding
CFGADDR/CFGDATA regions in the ISD MMIO and remove the unused
code in the current ISD read/write handlers.
Update the mapping when PCI0_CMD register is accessed (in case
the endianness is changed).
This allows using the GT64120 on a big-endian host (and boot
the MIPS Malta machine in little-endian).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-6-philmd@linaro.org>
Single registers access in ISD can produce multiple changes
in the address spaces. To reduce computational effort,
accumulate these as a single memory transaction.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-5-philmd@linaro.org>
The FPGA LEDs/ASCII display is mostly used by the bootloader
to show very low-level debug info. QEMU connects its output
to a character device backend, which is not very practical
to correlate with ASM instruction executed, interrupts or
MMIO accesses. Also, the display discard the previous states.
To ease bootloader debugging experience, add a pair of trace
events. Such events can be analyzed over time or diff-ed
between different runs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-4-philmd@linaro.org>
No need to refresh the ASCII bar when a LED is toggled
(and vice versa).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230104133935.4639-3-philmd@linaro.org>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Translate embedded assembly into IO writes which is more
readable.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210127065424.114125-4-jiaxun.yang@flygoat.com>
[PMD: Explode addresses/values to ease review/maintainance]
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221026191821.28167-4-philmd@linaro.org>
When one of the $sp/$a[0..3] register is already set, we might
want bl_gen_jump_kernel() to NOT set it again. Pass a boolean
argument for each register, to allow to optionally set them.
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221026191821.28167-2-philmd@linaro.org>
PCIe port 0 and 1 had link_up set as false previously,
that makes those two ports effectively useless. It can
be annoying for users to find that the device they plug
on those buses won't work at all.
As link_up is true by default, just don't set it again in
boston platform code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20221024143540.97545-1-jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
For the VIA south bridges there was a comment to have the call in board code.
Move it there for PIIX4 as well for consistency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20221022150508.26830-29-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
While at it, move the assignments closer to where they are used.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221022150508.26830-26-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Several machines have an unused MAX_IDE_BUS define. Remove it from
these machines that don't need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220917115136.A32EF746E06@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
According to good QOM practice, an object should only deal with objects
of its own sub tree. Having devices create an alias on the machine
object doesn't respect this good practice. To resolve this, create the
alias in the machine's code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-14-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The previous patches moved most of this function into the via-isa device
model such that it has become fairly trivial. So inline it for
simplicity.
Suggested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220901114127.53914-12-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The AC97 function's wakeup status is wired to the PM function and both
the AC97 and MC97 interrupt routing is determined by the ISA function.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-11-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PM controller has activity bits which monitor activity of other
built-in devices in the host device.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-10-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The USB functions can be enabled/disabled through the ISA function. Also
its interrupt routing can be influenced there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The IDE function is closely tied to the ISA function (e.g. the IDE
interrupt routing happens there), so it makes sense that the IDE
function is instantiated within the south bridge itself.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Establishes consistency with other (VIA) devices.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220901114127.53914-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
As of the kernel commit linked below, Linux ingests an RNG seed
passed as part of the environment block by the bootloader or firmware.
This mechanism works across all different environment block types,
generically, which pass some block via the second firmware argument. On
malta, this has been tested to work when passed as an argument from
U-Boot's linux_env_set.
As is the case on most other architectures (such as boston), when
booting with `-kernel`, QEMU, acting as the bootloader, should pass the
RNG seed, so that the machine has good entropy for Linux to consume. So
this commit implements that quite simply by using the guest random API,
which is what is used on nearly all other archs too. It also
reinitializes the seed on reboot, so that it is always fresh.
Link: https://git.kernel.org/torvalds/c/056a68cea01
Cc: Aleksandar Rikalo <aleksandar.rikalo@syrmia.com>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the system reboots, the rng-seed that the FDT has should be
re-randomized, so that the new boot gets a new seed. Since the FDT is in
the ROM region at this point, we add a hook right after the ROM has been
added, so that we have a pointer to that copy of the FDT.
Cc: Aleksandar Rikalo <aleksandar.rikalo@syrmia.com>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-id: 20221025004327.568476-9-Jason@zx2c4.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU crashes trying to save VMSTATE when only MIPS target are compiled in
$ qemu-system-mips -monitor stdio
(qemu) migrate "exec:gzip -c > STATEFILE.gz"
Segmentation fault (core dumped)
It happens due to PIIX4_PM trying to parse hotplug vmstate structures
which are valid only for x86 and not for MIPS (as it requires ACPI
tables support which is not existent for ithe later)
Issue was probably exposed by trying to cleanup/compile out unused
ACPI bits from MIPS target (but forgetting about migration bits).
Disable compiled out features using compat properties as the least
risky way to deal with issue.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/995
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220728115034.1327988-1-imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
If the FDT contains /chosen/rng-seed, then the Linux RNG will use it to
initialize early. Set this using the usual guest random number
generation function. This FDT node is part of the DT specification.
I'd do the same for other MIPS platforms but boston is the only one that
seems to use FDT.
Cc: Paul Burton <paulburton@kernel.org>
Cc: Aleksandar Rikalo <aleksandar.rikalo@syrmia.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220719120843.134392-1-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This legacy function is only used during the initialisation of the MIPS magnum
machine, so inline its functionality directly into mips_jazz_init() and then
remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-41-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
