linux/arch/arm/boot/dts/imx28-apx4devkit.dts
Shawn Guo 352d318cc9 ARM: dts: imx: use generic node name for fixed regulator
The device tree specification recommends that generic name should be
used for nodes.  So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-02-09 21:32:30 +08:00

227 lines
4.9 KiB
Plaintext

/dts-v1/;
#include "imx28.dtsi"
/ {
model = "Bluegiga APX4 Development Kit";
compatible = "bluegiga,apx4devkit", "fsl,imx28";
memory {
reg = <0x40000000 0x04000000>;
};
apb@80000000 {
apbh@80000000 {
gpmi-nand@8000c000 {
pinctrl-names = "default";
pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
status = "okay";
};
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
bus-width = <4>;
status = "okay";
};
ssp2: ssp@80014000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
bus-width = <4>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_CE1N__GPIO_0_17
MX28_PAD_GPMI_RDY1__GPIO_0_21
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
MX28_PAD_PWM3__GPIO_3_28
MX28_PAD_LCD_RESET__GPIO_3_30
MX28_PAD_JTAG_RTCK__GPIO_4_20
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_apx4: lcdif-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA4__SSP2_D0
MX28_PAD_SSP0_DATA5__SSP2_D3
MX28_PAD_SSP0_DATA6__SSP2_CMD
MX28_PAD_SSP0_DATA7__SSP2_SCK
MX28_PAD_SSP2_SS1__SSP2_D1
MX28_PAD_SSP2_SS2__SSP2_D2
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 {
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
fsl,drive-strength = <MXS_DRIVE_12mA>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_apx4>;
display = <&display>;
status = "okay";
display: display {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <30000000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hfront-porch = <40>;
vback-porch = <32>;
vfront-porch = <13>;
hsync-len = <48>;
vsync-len = <3>;
hsync-active = <1>;
vsync-active = <1>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
};
apbx@80040000 {
saif0: saif@80042000 {
pinctrl-names = "default";
pinctrl-0 = <&saif0_pins_a>;
status = "okay";
};
saif1: saif@80046000 {
pinctrl-names = "default";
pinctrl-0 = <&saif1_pins_a>;
fsl,saif-master = <&saif0>;
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
VDDA-supply = <&reg_3p3v>;
VDDIO-supply = <&reg_3p3v>;
clocks = <&saif0>;
};
pcf8563: rtc@51 {
compatible = "phg,pcf8563";
reg = <0x51>;
};
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_pins_a>;
status = "okay";
};
auart1: serial@8006c000 {
pinctrl-names = "default";
pinctrl-0 = <&auart1_2pins_a>;
status = "okay";
};
auart2: serial@8006e000 {
pinctrl-names = "default";
pinctrl-0 = <&auart2_2pins_a>;
status = "okay";
};
};
};
ahb@80080000 {
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
status = "okay";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
sound {
compatible = "bluegiga,apx4devkit-sgtl5000",
"fsl,mxs-audio-sgtl5000";
model = "apx4devkit-sgtl5000";
saif-controllers = <&saif0 &saif1>;
audio-codec = <&sgtl5000>;
};
leds {
compatible = "gpio-leds";
user {
label = "Heartbeat";
gpios = <&gpio3 28 0>;
linux,default-trigger = "heartbeat";
};
};
};