linux/drivers/mtd/nand/atmel_nand_ecc.h
Romain Izard 94248462f0 mtd: atmel_nand: Support 32-bit ECC strength
As the SAMA5D2 controller supports the 32-bit ECC strength, accept it
as a valid setting when required by the device tree or the NAND
parameter page.

Then configure the controller to use this new setting.

For the binding:
Acked-by: Rob Herring <robh@kernel.org>

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2016-02-12 10:27:48 -08:00

164 lines
5.8 KiB
C

/*
* Error Corrected Code Controller (ECC) - System peripherals regsters.
* Based on AT91SAM9260 datasheet revision B.
*
* Copyright (C) 2007 Andrew Victor
* Copyright (C) 2007 - 2012 Atmel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#ifndef ATMEL_NAND_ECC_H
#define ATMEL_NAND_ECC_H
#define ATMEL_ECC_CR 0x00 /* Control register */
#define ATMEL_ECC_RST (1 << 0) /* Reset parity */
#define ATMEL_ECC_MR 0x04 /* Mode register */
#define ATMEL_ECC_PAGESIZE (3 << 0) /* Page Size */
#define ATMEL_ECC_PAGESIZE_528 (0)
#define ATMEL_ECC_PAGESIZE_1056 (1)
#define ATMEL_ECC_PAGESIZE_2112 (2)
#define ATMEL_ECC_PAGESIZE_4224 (3)
#define ATMEL_ECC_SR 0x08 /* Status register */
#define ATMEL_ECC_RECERR (1 << 0) /* Recoverable Error */
#define ATMEL_ECC_ECCERR (1 << 1) /* ECC Single Bit Error */
#define ATMEL_ECC_MULERR (1 << 2) /* Multiple Errors */
#define ATMEL_ECC_PR 0x0c /* Parity register */
#define ATMEL_ECC_BITADDR (0xf << 0) /* Bit Error Address */
#define ATMEL_ECC_WORDADDR (0xfff << 4) /* Word Error Address */
#define ATMEL_ECC_NPR 0x10 /* NParity register */
#define ATMEL_ECC_NPARITY (0xffff << 0) /* NParity */
/* PMECC Register Definitions */
#define ATMEL_PMECC_CFG 0x000 /* Configuration Register */
#define PMECC_CFG_BCH_ERR2 (0 << 0)
#define PMECC_CFG_BCH_ERR4 (1 << 0)
#define PMECC_CFG_BCH_ERR8 (2 << 0)
#define PMECC_CFG_BCH_ERR12 (3 << 0)
#define PMECC_CFG_BCH_ERR24 (4 << 0)
#define PMECC_CFG_BCH_ERR32 (5 << 0)
#define PMECC_CFG_SECTOR512 (0 << 4)
#define PMECC_CFG_SECTOR1024 (1 << 4)
#define PMECC_CFG_PAGE_1SECTOR (0 << 8)
#define PMECC_CFG_PAGE_2SECTORS (1 << 8)
#define PMECC_CFG_PAGE_4SECTORS (2 << 8)
#define PMECC_CFG_PAGE_8SECTORS (3 << 8)
#define PMECC_CFG_READ_OP (0 << 12)
#define PMECC_CFG_WRITE_OP (1 << 12)
#define PMECC_CFG_SPARE_ENABLE (1 << 16)
#define PMECC_CFG_SPARE_DISABLE (0 << 16)
#define PMECC_CFG_AUTO_ENABLE (1 << 20)
#define PMECC_CFG_AUTO_DISABLE (0 << 20)
#define ATMEL_PMECC_SAREA 0x004 /* Spare area size */
#define ATMEL_PMECC_SADDR 0x008 /* PMECC starting address */
#define ATMEL_PMECC_EADDR 0x00c /* PMECC ending address */
#define ATMEL_PMECC_CLK 0x010 /* PMECC clock control */
#define PMECC_CLK_133MHZ (2 << 0)
#define ATMEL_PMECC_CTRL 0x014 /* PMECC control register */
#define PMECC_CTRL_RST (1 << 0)
#define PMECC_CTRL_DATA (1 << 1)
#define PMECC_CTRL_USER (1 << 2)
#define PMECC_CTRL_ENABLE (1 << 4)
#define PMECC_CTRL_DISABLE (1 << 5)
#define ATMEL_PMECC_SR 0x018 /* PMECC status register */
#define PMECC_SR_BUSY (1 << 0)
#define PMECC_SR_ENABLE (1 << 4)
#define ATMEL_PMECC_IER 0x01c /* PMECC interrupt enable */
#define PMECC_IER_ENABLE (1 << 0)
#define ATMEL_PMECC_IDR 0x020 /* PMECC interrupt disable */
#define PMECC_IER_DISABLE (1 << 0)
#define ATMEL_PMECC_IMR 0x024 /* PMECC interrupt mask */
#define PMECC_IER_MASK (1 << 0)
#define ATMEL_PMECC_ISR 0x028 /* PMECC interrupt status */
#define ATMEL_PMECC_ECCx 0x040 /* PMECC ECC x */
#define ATMEL_PMECC_REMx 0x240 /* PMECC REM x */
/* PMERRLOC Register Definitions */
#define ATMEL_PMERRLOC_ELCFG 0x000 /* Error location config */
#define PMERRLOC_ELCFG_SECTOR_512 (0 << 0)
#define PMERRLOC_ELCFG_SECTOR_1024 (1 << 0)
#define PMERRLOC_ELCFG_NUM_ERRORS(n) ((n) << 16)
#define ATMEL_PMERRLOC_ELPRIM 0x004 /* Error location primitive */
#define ATMEL_PMERRLOC_ELEN 0x008 /* Error location enable */
#define ATMEL_PMERRLOC_ELDIS 0x00c /* Error location disable */
#define PMERRLOC_DISABLE (1 << 0)
#define ATMEL_PMERRLOC_ELSR 0x010 /* Error location status */
#define PMERRLOC_ELSR_BUSY (1 << 0)
#define ATMEL_PMERRLOC_ELIER 0x014 /* Error location int enable */
#define ATMEL_PMERRLOC_ELIDR 0x018 /* Error location int disable */
#define ATMEL_PMERRLOC_ELIMR 0x01c /* Error location int mask */
#define ATMEL_PMERRLOC_ELISR 0x020 /* Error location int status */
#define PMERRLOC_ERR_NUM_MASK (0x1f << 8)
#define PMERRLOC_CALC_DONE (1 << 0)
#define ATMEL_PMERRLOC_SIGMAx 0x028 /* Error location SIGMA x */
/*
* The ATMEL_PMERRLOC_ELx register location depends from the number of
* bits corrected by the PMECC controller. Do not use it.
*/
/* Register access macros for PMECC */
#define pmecc_readl_relaxed(addr, reg) \
readl_relaxed((addr) + ATMEL_PMECC_##reg)
#define pmecc_writel(addr, reg, value) \
writel((value), (addr) + ATMEL_PMECC_##reg)
#define pmecc_readb_ecc_relaxed(addr, sector, n) \
readb_relaxed((addr) + ATMEL_PMECC_ECCx + ((sector) * 0x40) + (n))
#define pmecc_readl_rem_relaxed(addr, sector, n) \
readl_relaxed((addr) + ATMEL_PMECC_REMx + ((sector) * 0x40) + ((n) * 4))
#define pmerrloc_readl_relaxed(addr, reg) \
readl_relaxed((addr) + ATMEL_PMERRLOC_##reg)
#define pmerrloc_writel(addr, reg, value) \
writel((value), (addr) + ATMEL_PMERRLOC_##reg)
#define pmerrloc_writel_sigma_relaxed(addr, n, value) \
writel_relaxed((value), (addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
#define pmerrloc_readl_sigma_relaxed(addr, n) \
readl_relaxed((addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
#define pmerrloc_readl_el_relaxed(addr, n) \
readl_relaxed((addr) + ((n) * 4))
/* Galois field dimension */
#define PMECC_GF_DIMENSION_13 13
#define PMECC_GF_DIMENSION_14 14
/* Primitive Polynomial used by PMECC */
#define PMECC_GF_13_PRIMITIVE_POLY 0x201b
#define PMECC_GF_14_PRIMITIVE_POLY 0x4443
#define PMECC_LOOKUP_TABLE_SIZE_512 0x2000
#define PMECC_LOOKUP_TABLE_SIZE_1024 0x4000
/* Time out value for reading PMECC status register */
#define PMECC_MAX_TIMEOUT_MS 100
/* Reserved bytes in oob area */
#define PMECC_OOB_RESERVED_BYTES 2
#endif