linux/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi
Philipp Zabel 1e44d3f880 ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
This patch enables I2C1 and adds device tree nodes for the EEPROM and the
DA9063 PMIC connected to this I2C bus.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:50 +08:00

181 lines
3.7 KiB
Plaintext

/*
* Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include "imx6q.dtsi"
/ {
model = "Phytec phyFLEX-i.MX6 Ouad";
compatible = "phytec,imx6q-pfla02", "fsl,imx6q";
memory {
reg = <0x10000000 0x80000000>;
};
};
&ecspi3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3_1>;
status = "okay";
fsl,spi-num-chipselects = <1>;
cs-gpios = <&gpio4 24 0>;
flash@0 {
compatible = "m25p80";
spi-max-frequency = <20000000>;
reg = <0>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1_1>;
status = "okay";
eeprom@50 {
compatible = "atmel,24c32";
reg = <0x50>;
};
pmic@58 {
compatible = "dialog,da9063";
reg = <0x58>;
interrupt-parent = <&gpio4>;
interrupts = <17 0x8>; /* active-low GPIO4_17 */
regulators {
vddcore_reg: bcore1 {
regulator-min-microvolt = <730000>;
regulator-max-microvolt = <1380000>;
regulator-always-on;
};
vddsoc_reg: bcore2 {
regulator-min-microvolt = <730000>;
regulator-max-microvolt = <1380000>;
regulator-always-on;
};
vdd_ddr3_reg: bpro {
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
};
vdd_3v3_reg: bperi {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_buckmem_reg: bmem {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_eth_reg: bio {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vdd_eth_io_reg: ldo4 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-always-on;
};
vdd_mx6_snvs_reg: ldo5 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
vdd_3v3_pmic_io_reg: ldo6 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_sd0_reg: ldo9 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vdd_sd1_reg: ldo10 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vdd_mx6_high_reg: ldo11 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
};
};
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
hog {
pinctrl_hog: hoggrp {
fsl,pins = <
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000
MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* SPI NOR chipselect */
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x80000000 /* PMIC interrupt */
>;
};
};
pfla02 {
pinctrl_usdhc3_pfla02: usdhc3grp-pfla02 {
fsl,pins = <
MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000
>;
};
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet_3>;
phy-mode = "rgmii";
phy-reset-gpios = <&gpio3 23 0>;
status = "disabled";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4_1>;
status = "disabled";
};
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2_2>;
cd-gpios = <&gpio1 4 0>;
wp-gpios = <&gpio1 2 0>;
status = "disabled";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3_2
&pinctrl_usdhc3_pfla02>;
cd-gpios = <&gpio1 27 0>;
wp-gpios = <&gpio1 29 0>;
status = "disabled";
};