mirror of
https://github.com/torvalds/linux
synced 2024-09-24 05:17:36 +00:00
9c7564620f
In order to not touch the driver file for different xtal usage, push the clkin value to board file and calculate the register value instead of hardcoding it. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
433 lines
11 KiB
C
433 lines
11 KiB
C
/*
|
|
* MUSB OTG controller driver for Blackfin Processors
|
|
*
|
|
* Copyright 2006-2008 Analog Devices Inc.
|
|
*
|
|
* Enter bugs at http://blackfin.uclinux.org/
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/init.h>
|
|
#include <linux/list.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/io.h>
|
|
|
|
#include <asm/cacheflush.h>
|
|
|
|
#include "musb_core.h"
|
|
#include "blackfin.h"
|
|
|
|
/*
|
|
* Load an endpoint's FIFO
|
|
*/
|
|
void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
|
|
{
|
|
void __iomem *fifo = hw_ep->fifo;
|
|
void __iomem *epio = hw_ep->regs;
|
|
u8 epnum = hw_ep->epnum;
|
|
|
|
prefetch((u8 *)src);
|
|
|
|
musb_writew(epio, MUSB_TXCOUNT, len);
|
|
|
|
DBG(4, "TX ep%d fifo %p count %d buf %p, epio %p\n",
|
|
hw_ep->epnum, fifo, len, src, epio);
|
|
|
|
dump_fifo_data(src, len);
|
|
|
|
if (!ANOMALY_05000380 && epnum != 0) {
|
|
u16 dma_reg;
|
|
|
|
flush_dcache_range((unsigned long)src,
|
|
(unsigned long)(src + len));
|
|
|
|
/* Setup DMA address register */
|
|
dma_reg = (u32)src;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
|
|
SSYNC();
|
|
|
|
dma_reg = (u32)src >> 16;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Setup DMA count register */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
|
|
SSYNC();
|
|
|
|
/* Enable the DMA */
|
|
dma_reg = (epnum << 4) | DMA_ENA | INT_ENA | DIRECTION;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Wait for compelete */
|
|
while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
|
|
cpu_relax();
|
|
|
|
/* acknowledge dma interrupt */
|
|
bfin_write_USB_DMA_INTERRUPT(1 << epnum);
|
|
SSYNC();
|
|
|
|
/* Reset DMA */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
|
|
SSYNC();
|
|
} else {
|
|
SSYNC();
|
|
|
|
if (unlikely((unsigned long)src & 0x01))
|
|
outsw_8((unsigned long)fifo, src, (len + 1) >> 1);
|
|
else
|
|
outsw((unsigned long)fifo, src, (len + 1) >> 1);
|
|
}
|
|
}
|
|
/*
|
|
* Unload an endpoint's FIFO
|
|
*/
|
|
void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
|
|
{
|
|
void __iomem *fifo = hw_ep->fifo;
|
|
u8 epnum = hw_ep->epnum;
|
|
|
|
if (ANOMALY_05000467 && epnum != 0) {
|
|
u16 dma_reg;
|
|
|
|
invalidate_dcache_range((unsigned long)dst,
|
|
(unsigned long)(dst + len));
|
|
|
|
/* Setup DMA address register */
|
|
dma_reg = (u32)dst;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
|
|
SSYNC();
|
|
|
|
dma_reg = (u32)dst >> 16;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Setup DMA count register */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
|
|
SSYNC();
|
|
|
|
/* Enable the DMA */
|
|
dma_reg = (epnum << 4) | DMA_ENA | INT_ENA;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Wait for compelete */
|
|
while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
|
|
cpu_relax();
|
|
|
|
/* acknowledge dma interrupt */
|
|
bfin_write_USB_DMA_INTERRUPT(1 << epnum);
|
|
SSYNC();
|
|
|
|
/* Reset DMA */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
|
|
SSYNC();
|
|
} else {
|
|
SSYNC();
|
|
/* Read the last byte of packet with odd size from address fifo + 4
|
|
* to trigger 1 byte access to EP0 FIFO.
|
|
*/
|
|
if (len == 1)
|
|
*dst = (u8)inw((unsigned long)fifo + 4);
|
|
else {
|
|
if (unlikely((unsigned long)dst & 0x01))
|
|
insw_8((unsigned long)fifo, dst, len >> 1);
|
|
else
|
|
insw((unsigned long)fifo, dst, len >> 1);
|
|
|
|
if (len & 0x01)
|
|
*(dst + len - 1) = (u8)inw((unsigned long)fifo + 4);
|
|
}
|
|
}
|
|
DBG(4, "%cX ep%d fifo %p count %d buf %p\n",
|
|
'R', hw_ep->epnum, fifo, len, dst);
|
|
|
|
dump_fifo_data(dst, len);
|
|
}
|
|
|
|
static irqreturn_t blackfin_interrupt(int irq, void *__hci)
|
|
{
|
|
unsigned long flags;
|
|
irqreturn_t retval = IRQ_NONE;
|
|
struct musb *musb = __hci;
|
|
|
|
spin_lock_irqsave(&musb->lock, flags);
|
|
|
|
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
|
|
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
|
|
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
|
|
|
|
if (musb->int_usb || musb->int_tx || musb->int_rx) {
|
|
musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
|
|
musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
|
|
musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
|
|
retval = musb_interrupt(musb);
|
|
}
|
|
|
|
/* Start sampling ID pin, when plug is removed from MUSB */
|
|
if ((is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
|
|
|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) ||
|
|
(musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
|
|
musb->a_wait_bcon = TIMER_DELAY;
|
|
}
|
|
|
|
spin_unlock_irqrestore(&musb->lock, flags);
|
|
|
|
return retval;
|
|
}
|
|
|
|
static void musb_conn_timer_handler(unsigned long _musb)
|
|
{
|
|
struct musb *musb = (void *)_musb;
|
|
unsigned long flags;
|
|
u16 val;
|
|
static u8 toggle;
|
|
|
|
spin_lock_irqsave(&musb->lock, flags);
|
|
switch (musb->xceiv->state) {
|
|
case OTG_STATE_A_IDLE:
|
|
case OTG_STATE_A_WAIT_BCON:
|
|
/* Start a new session */
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
val &= ~MUSB_DEVCTL_SESSION;
|
|
musb_writew(musb->mregs, MUSB_DEVCTL, val);
|
|
val |= MUSB_DEVCTL_SESSION;
|
|
musb_writew(musb->mregs, MUSB_DEVCTL, val);
|
|
/* Check if musb is host or peripheral. */
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
|
|
if (!(val & MUSB_DEVCTL_BDEVICE)) {
|
|
gpio_set_value(musb->config->gpio_vrsel, 1);
|
|
musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
|
|
} else {
|
|
gpio_set_value(musb->config->gpio_vrsel, 0);
|
|
/* Ignore VBUSERROR and SUSPEND IRQ */
|
|
val = musb_readb(musb->mregs, MUSB_INTRUSBE);
|
|
val &= ~MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
|
|
|
|
val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSB, val);
|
|
if (is_otg_enabled(musb))
|
|
musb->xceiv->state = OTG_STATE_B_IDLE;
|
|
else
|
|
musb_writeb(musb->mregs, MUSB_POWER, MUSB_POWER_HSENAB);
|
|
}
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
|
|
break;
|
|
case OTG_STATE_B_IDLE:
|
|
|
|
if (!is_peripheral_enabled(musb))
|
|
break;
|
|
/* Start a new session. It seems that MUSB needs taking
|
|
* some time to recognize the type of the plug inserted?
|
|
*/
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
val |= MUSB_DEVCTL_SESSION;
|
|
musb_writew(musb->mregs, MUSB_DEVCTL, val);
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
|
|
if (!(val & MUSB_DEVCTL_BDEVICE)) {
|
|
gpio_set_value(musb->config->gpio_vrsel, 1);
|
|
musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
|
|
} else {
|
|
gpio_set_value(musb->config->gpio_vrsel, 0);
|
|
|
|
/* Ignore VBUSERROR and SUSPEND IRQ */
|
|
val = musb_readb(musb->mregs, MUSB_INTRUSBE);
|
|
val &= ~MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
|
|
|
|
val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSB, val);
|
|
|
|
/* Toggle the Soft Conn bit, so that we can response to
|
|
* the inserting of either A-plug or B-plug.
|
|
*/
|
|
if (toggle) {
|
|
val = musb_readb(musb->mregs, MUSB_POWER);
|
|
val &= ~MUSB_POWER_SOFTCONN;
|
|
musb_writeb(musb->mregs, MUSB_POWER, val);
|
|
toggle = 0;
|
|
} else {
|
|
val = musb_readb(musb->mregs, MUSB_POWER);
|
|
val |= MUSB_POWER_SOFTCONN;
|
|
musb_writeb(musb->mregs, MUSB_POWER, val);
|
|
toggle = 1;
|
|
}
|
|
/* The delay time is set to 1/4 second by default,
|
|
* shortening it, if accelerating A-plug detection
|
|
* is needed in OTG mode.
|
|
*/
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY / 4);
|
|
}
|
|
break;
|
|
default:
|
|
DBG(1, "%s state not handled\n", otg_state_string(musb));
|
|
break;
|
|
}
|
|
spin_unlock_irqrestore(&musb->lock, flags);
|
|
|
|
DBG(4, "state is %s\n", otg_state_string(musb));
|
|
}
|
|
|
|
void musb_platform_enable(struct musb *musb)
|
|
{
|
|
if (!is_otg_enabled(musb) && is_host_enabled(musb)) {
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
|
|
musb->a_wait_bcon = TIMER_DELAY;
|
|
}
|
|
}
|
|
|
|
void musb_platform_disable(struct musb *musb)
|
|
{
|
|
}
|
|
|
|
static void bfin_set_vbus(struct musb *musb, int is_on)
|
|
{
|
|
int value = musb->config->gpio_vrsel_active;
|
|
if (!is_on)
|
|
value = !value;
|
|
gpio_set_value(musb->config->gpio_vrsel, value);
|
|
|
|
DBG(1, "VBUS %s, devctl %02x "
|
|
/* otg %3x conf %08x prcm %08x */ "\n",
|
|
otg_state_string(musb),
|
|
musb_readb(musb->mregs, MUSB_DEVCTL));
|
|
}
|
|
|
|
static int bfin_set_power(struct otg_transceiver *x, unsigned mA)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
void musb_platform_try_idle(struct musb *musb, unsigned long timeout)
|
|
{
|
|
if (!is_otg_enabled(musb) && is_host_enabled(musb))
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
|
|
}
|
|
|
|
int musb_platform_get_vbus_status(struct musb *musb)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
|
|
{
|
|
return -EIO;
|
|
}
|
|
|
|
static void musb_platform_reg_init(struct musb *musb)
|
|
{
|
|
if (ANOMALY_05000346) {
|
|
bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
|
|
SSYNC();
|
|
}
|
|
|
|
if (ANOMALY_05000347) {
|
|
bfin_write_USB_APHY_CNTRL(0x0);
|
|
SSYNC();
|
|
}
|
|
|
|
/* Configure PLL oscillator register */
|
|
bfin_write_USB_PLLOSC_CTRL(0x3080 |
|
|
((480/musb->config->clkin) << 1));
|
|
SSYNC();
|
|
|
|
bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
|
|
SSYNC();
|
|
|
|
bfin_write_USB_EP_NI0_RXMAXP(64);
|
|
SSYNC();
|
|
|
|
bfin_write_USB_EP_NI0_TXMAXP(64);
|
|
SSYNC();
|
|
|
|
/* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/
|
|
bfin_write_USB_GLOBINTR(0x7);
|
|
SSYNC();
|
|
|
|
bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA |
|
|
EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA |
|
|
EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA |
|
|
EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
|
|
EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
|
|
SSYNC();
|
|
}
|
|
|
|
int __init musb_platform_init(struct musb *musb, void *board_data)
|
|
{
|
|
|
|
/*
|
|
* Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
|
|
* and OTG HOST modes, while rev 1.1 and greater require PE7 to
|
|
* be low for DEVICE mode and high for HOST mode. We set it high
|
|
* here because we are in host mode
|
|
*/
|
|
|
|
if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
|
|
printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
|
|
musb->config->gpio_vrsel);
|
|
return -ENODEV;
|
|
}
|
|
gpio_direction_output(musb->config->gpio_vrsel, 0);
|
|
|
|
usb_nop_xceiv_register();
|
|
musb->xceiv = otg_get_transceiver();
|
|
if (!musb->xceiv) {
|
|
gpio_free(musb->config->gpio_vrsel);
|
|
return -ENODEV;
|
|
}
|
|
|
|
musb_platform_reg_init(musb);
|
|
|
|
if (is_host_enabled(musb)) {
|
|
musb->board_set_vbus = bfin_set_vbus;
|
|
setup_timer(&musb_conn_timer,
|
|
musb_conn_timer_handler, (unsigned long) musb);
|
|
}
|
|
if (is_peripheral_enabled(musb))
|
|
musb->xceiv->set_power = bfin_set_power;
|
|
|
|
musb->isr = blackfin_interrupt;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
void musb_platform_save_context(struct musb *musb,
|
|
struct musb_context_registers *musb_context)
|
|
{
|
|
if (is_host_active(musb))
|
|
/*
|
|
* During hibernate gpio_vrsel will change from high to low
|
|
* low which will generate wakeup event resume the system
|
|
* immediately. Set it to 0 before hibernate to avoid this
|
|
* wakeup event.
|
|
*/
|
|
gpio_set_value(musb->config->gpio_vrsel, 0);
|
|
}
|
|
|
|
void musb_platform_restore_context(struct musb *musb,
|
|
struct musb_context_registers *musb_context)
|
|
{
|
|
musb_platform_reg_init(musb);
|
|
}
|
|
#endif
|
|
|
|
int musb_platform_exit(struct musb *musb)
|
|
{
|
|
gpio_free(musb->config->gpio_vrsel);
|
|
|
|
otg_put_transceiver(musb->xceiv);
|
|
usb_nop_xceiv_unregister();
|
|
return 0;
|
|
}
|