linux/arch/arm/boot/dts/kirkwood-topkick.dts
Sebastian Hesselbarth ce55b1f423 ARM: dts: kirkwood: set default pinctrl for I2C0
There is only one valid pinctrl setting for I2C0 on Kirkwood. Now that we
have the setting in the common SoC pinctrl, move it to the I2C0 controller
node directly and remove it from the individual boards.

While at it, also fix up status = "okay" to "ok" on one board's I2C0 node.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-13-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2014-05-05 00:53:15 +00:00

216 lines
3.9 KiB
Plaintext

/dts-v1/;
#include "kirkwood.dtsi"
#include "kirkwood-6282.dtsi"
/ {
model = "Univeral Scientific Industrial Co. Topkick-1281P2";
compatible = "usi,topkick-1281P2", "usi,topkick", "marvell,kirkwood-88f6282", "marvell,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
stdout-path = &uart0;
};
ocp@f1000000 {
pinctrl: pin-controller@10000 {
/*
* Switch positions
*
* /-SW_LEFT(2)
* |
* | /-SW_IDLE
* | |
* | | /-SW_RIGHT
* | | |
* PS [L] [I] [R] LEDS
*/
pinctrl-0 = <&pmx_sw_left &pmx_sw_right
&pmx_sw_idle &pmx_sw_left2>;
pinctrl-names = "default";
pmx_led_disk_yellow: pmx-led-disk-yellow {
marvell,pins = "mpp21";
marvell,function = "gpio";
};
pmx_sata0_pwr_enable: pmx-sata0-pwr-enable {
marvell,pins = "mpp36";
marvell,function = "gpio";
};
pmx_led_sys_red: pmx-led-sys-red {
marvell,pins = "mpp37";
marvell,function = "gpio";
};
pmx_led_sys_blue: pmx-led-sys-blue {
marvell,pins = "mpp38";
marvell,function = "gpio";
};
pmx_led_wifi_green: pmx-led-wifi-green {
marvell,pins = "mpp39";
marvell,function = "gpio";
};
pmx_sw_left: pmx-sw-left {
marvell,pins = "mpp43";
marvell,function = "gpio";
};
pmx_sw_right: pmx-sw-right {
marvell,pins = "mpp44";
marvell,function = "gpio";
};
pmx_sw_idle: pmx-sw-idle {
marvell,pins = "mpp45";
marvell,function = "gpio";
};
pmx_sw_left2: pmx-sw-left2 {
marvell,pins = "mpp46";
marvell,function = "gpio";
};
pmx_led_wifi_yellow: pmx-led-wifi-yellow {
marvell,pins = "mpp48";
marvell,function = "gpio";
};
};
serial@12000 {
status = "okay";
};
sata@80000 {
status = "okay";
nr-ports = <1>;
};
i2c@11000 {
status = "okay";
};
mvsdio@90000 {
pinctrl-0 = <&pmx_sdio>;
pinctrl-names = "default";
status = "okay";
/* No CD or WP GPIOs */
broken-cd;
};
};
gpio-leds {
/*
* GPIO LED layout
*
* /-SYS_LED(2)
* |
* | /-DISK_LED
* | |
* | | /-WLAN_LED(2)
* | | |
* [SW] [*] [*] [*]
*/
compatible = "gpio-leds";
pinctrl-0 = <&pmx_led_disk_yellow &pmx_led_sys_red
&pmx_led_sys_blue &pmx_led_wifi_green
&pmx_led_wifi_yellow>;
pinctrl-names = "default";
disk {
label = "topkick:yellow:disk";
gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "ide-disk";
};
system2 {
label = "topkick:red:system";
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
};
system {
label = "topkick:blue:system";
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wifi {
label = "topkick:green:wifi";
gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
};
wifi2 {
label = "topkick:yellow:wifi";
gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&pmx_sata0_pwr_enable>;
pinctrl-names = "default";
sata0_power: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "SATA0 Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio1 4 0>;
};
};
};
&nand {
status = "okay";
partition@0 {
label = "u-boot";
reg = <0x0000000 0x180000>;
};
partition@180000 {
label = "u-boot env";
reg = <0x0180000 0x20000>;
};
partition@200000 {
label = "uImage";
reg = <0x0200000 0x600000>;
};
partition@800000 {
label = "uInitrd";
reg = <0x0800000 0x1000000>;
};
partition@1800000 {
label = "rootfs";
reg = <0x1800000 0xe800000>;
};
};
&mdio {
status = "okay";
ethphy0: ethernet-phy@0 {
reg = <0>;
};
};
&eth0 {
status = "okay";
ethernet0-port@0 {
phy-handle = <&ethphy0>;
};
};