linux/drivers/block/drbd/Kconfig
Bartlomiej Zolnierkiewicz 486c6fba90 drivers/block: remove redundant 'default n' from Kconfig-s
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.

Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:

    ...
    One side effect of (and the main motivation for) this change is making
    the following two definitions behave exactly the same:

        config FOO
                bool

        config FOO
                bool
                default n

    With this change, neither of these will generate a
    '# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
    That might make it clearer to people that a bare 'default n' is
    redundant.
    ...

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-10 14:11:08 -06:00

74 lines
2.4 KiB
Plaintext

# SPDX-License-Identifier: GPL-2.0
#
# DRBD device driver configuration
#
comment "DRBD disabled because PROC_FS or INET not selected"
depends on PROC_FS='n' || INET='n'
config BLK_DEV_DRBD
tristate "DRBD Distributed Replicated Block Device support"
depends on PROC_FS && INET
select LRU_CACHE
select LIBCRC32C
help
NOTE: In order to authenticate connections you have to select
CRYPTO_HMAC and a hash function as well.
DRBD is a shared-nothing, synchronously replicated block device. It
is designed to serve as a building block for high availability
clusters and in this context, is a "drop-in" replacement for shared
storage. Simplistically, you could see it as a network RAID 1.
Each minor device has a role, which can be 'primary' or 'secondary'.
On the node with the primary device the application is supposed to
run and to access the device (/dev/drbdX). Every write is sent to
the local 'lower level block device' and, across the network, to the
node with the device in 'secondary' state. The secondary device
simply writes the data to its lower level block device.
DRBD can also be used in dual-Primary mode (device writable on both
nodes), which means it can exhibit shared disk semantics in a
shared-nothing cluster. Needless to say, on top of dual-Primary
DRBD utilizing a cluster file system is necessary to maintain for
cache coherency.
For automatic failover you need a cluster manager (e.g. heartbeat).
See also: http://www.drbd.org/, http://www.linux-ha.org
If unsure, say N.
config DRBD_FAULT_INJECTION
bool "DRBD fault injection"
depends on BLK_DEV_DRBD
help
Say Y here if you want to simulate IO errors, in order to test DRBD's
behavior.
The actual simulation of IO errors is done by writing 3 values to
/sys/module/drbd/parameters/
enable_faults: bitmask of...
1 meta data write
2 read
4 resync data write
8 read
16 data write
32 data read
64 read ahead
128 kmalloc of bitmap
256 allocation of peer_requests
512 insert data corruption on receiving side
fault_devs: bitmask of minor numbers
fault_rate: frequency in percent
Example: Simulate data write errors on /dev/drbd0 with a probability of 5%.
echo 16 > /sys/module/drbd/parameters/enable_faults
echo 1 > /sys/module/drbd/parameters/fault_devs
echo 5 > /sys/module/drbd/parameters/fault_rate
If unsure, say N.