linux/arch/powerpc/kernel/head_8xx.S
Joakim Tjernlund 469d62be92 powerpc/8xx: Use SPRG2 and DAR registers to stash r11 and cr.
This avoids storing these registers in memory.
CPU6 errata will still use the old way.
Remove some G2 leftover accesses from 2.4

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-04-07 18:00:34 +10:00

986 lines
28 KiB
ArmAsm

/*
* PowerPC version
* Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org)
* Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP
* Copyright (C) 1996 Cort Dougan <cort@cs.nmt.edu>
* Low-level exception handlers and MMU support
* rewritten by Paul Mackerras.
* Copyright (C) 1996 Paul Mackerras.
* MPC8xx modifications by Dan Malek
* Copyright (C) 1997 Dan Malek (dmalek@jlc.net).
*
* This file contains low-level support and setup for PowerPC 8xx
* embedded processors, including trap and interrupt dispatch.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*
*/
#include <linux/init.h>
#include <asm/processor.h>
#include <asm/page.h>
#include <asm/mmu.h>
#include <asm/cache.h>
#include <asm/pgtable.h>
#include <asm/cputable.h>
#include <asm/thread_info.h>
#include <asm/ppc_asm.h>
#include <asm/asm-offsets.h>
/* Macro to make the code more readable. */
#ifdef CONFIG_8xx_CPU6
#define DO_8xx_CPU6(val, reg) \
li reg, val; \
stw reg, 12(r0); \
lwz reg, 12(r0);
#else
#define DO_8xx_CPU6(val, reg)
#endif
__HEAD
_ENTRY(_stext);
_ENTRY(_start);
/* MPC8xx
* This port was done on an MBX board with an 860. Right now I only
* support an ELF compressed (zImage) boot from EPPC-Bug because the
* code there loads up some registers before calling us:
* r3: ptr to board info data
* r4: initrd_start or if no initrd then 0
* r5: initrd_end - unused if r4 is 0
* r6: Start of command line string
* r7: End of command line string
*
* I decided to use conditional compilation instead of checking PVR and
* adding more processor specific branches around code I don't need.
* Since this is an embedded processor, I also appreciate any memory
* savings I can get.
*
* The MPC8xx does not have any BATs, but it supports large page sizes.
* We first initialize the MMU to support 8M byte pages, then load one
* entry into each of the instruction and data TLBs to map the first
* 8M 1:1. I also mapped an additional I/O space 1:1 so we can get to
* the "internal" processor registers before MMU_init is called.
*
* The TLB code currently contains a major hack. Since I use the condition
* code register, I have to save and restore it. I am out of registers, so
* I just store it in memory location 0 (the TLB handlers are not reentrant).
* To avoid making any decisions, I need to use the "segment" valid bit
* in the first level table, but that would require many changes to the
* Linux page directory/table functions that I don't want to do right now.
*
* -- Dan
*/
.globl __start
__start:
mr r31,r3 /* save parameters */
mr r30,r4
mr r29,r5
mr r28,r6
mr r27,r7
/* We have to turn on the MMU right away so we get cache modes
* set correctly.
*/
bl initial_mmu
/* We now have the lower 8 Meg mapped into TLB entries, and the caches
* ready to work.
*/
turn_on_mmu:
mfmsr r0
ori r0,r0,MSR_DR|MSR_IR
mtspr SPRN_SRR1,r0
lis r0,start_here@h
ori r0,r0,start_here@l
mtspr SPRN_SRR0,r0
SYNC
rfi /* enables MMU */
/*
* Exception entry code. This code runs with address translation
* turned off, i.e. using physical addresses.
* We assume sprg3 has the physical address of the current
* task's thread_struct.
*/
#define EXCEPTION_PROLOG \
mtspr SPRN_SPRG_SCRATCH0,r10; \
mtspr SPRN_SPRG_SCRATCH1,r11; \
mfcr r10; \
EXCEPTION_PROLOG_1; \
EXCEPTION_PROLOG_2
#define EXCEPTION_PROLOG_1 \
mfspr r11,SPRN_SRR1; /* check whether user or kernel */ \
andi. r11,r11,MSR_PR; \
tophys(r11,r1); /* use tophys(r1) if kernel */ \
beq 1f; \
mfspr r11,SPRN_SPRG_THREAD; \
lwz r11,THREAD_INFO-THREAD(r11); \
addi r11,r11,THREAD_SIZE; \
tophys(r11,r11); \
1: subi r11,r11,INT_FRAME_SIZE /* alloc exc. frame */
#define EXCEPTION_PROLOG_2 \
CLR_TOP32(r11); \
stw r10,_CCR(r11); /* save registers */ \
stw r12,GPR12(r11); \
stw r9,GPR9(r11); \
mfspr r10,SPRN_SPRG_SCRATCH0; \
stw r10,GPR10(r11); \
mfspr r12,SPRN_SPRG_SCRATCH1; \
stw r12,GPR11(r11); \
mflr r10; \
stw r10,_LINK(r11); \
mfspr r12,SPRN_SRR0; \
mfspr r9,SPRN_SRR1; \
stw r1,GPR1(r11); \
stw r1,0(r11); \
tovirt(r1,r11); /* set new kernel sp */ \
li r10,MSR_KERNEL & ~(MSR_IR|MSR_DR); /* can take exceptions */ \
MTMSRD(r10); /* (except for mach check in rtas) */ \
stw r0,GPR0(r11); \
SAVE_4GPRS(3, r11); \
SAVE_2GPRS(7, r11)
/*
* Note: code which follows this uses cr0.eq (set if from kernel),
* r11, r12 (SRR0), and r9 (SRR1).
*
* Note2: once we have set r1 we are in a position to take exceptions
* again, and we could thus set MSR:RI at that point.
*/
/*
* Exception vectors.
*/
#define EXCEPTION(n, label, hdlr, xfer) \
. = n; \
label: \
EXCEPTION_PROLOG; \
addi r3,r1,STACK_FRAME_OVERHEAD; \
xfer(n, hdlr)
#define EXC_XFER_TEMPLATE(n, hdlr, trap, copyee, tfer, ret) \
li r10,trap; \
stw r10,_TRAP(r11); \
li r10,MSR_KERNEL; \
copyee(r10, r9); \
bl tfer; \
i##n: \
.long hdlr; \
.long ret
#define COPY_EE(d, s) rlwimi d,s,0,16,16
#define NOCOPY(d, s)
#define EXC_XFER_STD(n, hdlr) \
EXC_XFER_TEMPLATE(n, hdlr, n, NOCOPY, transfer_to_handler_full, \
ret_from_except_full)
#define EXC_XFER_LITE(n, hdlr) \
EXC_XFER_TEMPLATE(n, hdlr, n+1, NOCOPY, transfer_to_handler, \
ret_from_except)
#define EXC_XFER_EE(n, hdlr) \
EXC_XFER_TEMPLATE(n, hdlr, n, COPY_EE, transfer_to_handler_full, \
ret_from_except_full)
#define EXC_XFER_EE_LITE(n, hdlr) \
EXC_XFER_TEMPLATE(n, hdlr, n+1, COPY_EE, transfer_to_handler, \
ret_from_except)
/* System reset */
EXCEPTION(0x100, Reset, unknown_exception, EXC_XFER_STD)
/* Machine check */
. = 0x200
MachineCheck:
EXCEPTION_PROLOG
mfspr r4,SPRN_DAR
stw r4,_DAR(r11)
li r5,0x00f0
mtspr SPRN_DAR,r5 /* Tag DAR, to be used in DTLB Error */
mfspr r5,SPRN_DSISR
stw r5,_DSISR(r11)
addi r3,r1,STACK_FRAME_OVERHEAD
EXC_XFER_STD(0x200, machine_check_exception)
/* Data access exception.
* This is "never generated" by the MPC8xx. We jump to it for other
* translation errors.
*/
. = 0x300
DataAccess:
EXCEPTION_PROLOG
mfspr r10,SPRN_DSISR
stw r10,_DSISR(r11)
mr r5,r10
mfspr r4,SPRN_DAR
li r10,0x00f0
mtspr SPRN_DAR,r10 /* Tag DAR, to be used in DTLB Error */
EXC_XFER_EE_LITE(0x300, handle_page_fault)
/* Instruction access exception.
* This is "never generated" by the MPC8xx. We jump to it for other
* translation errors.
*/
. = 0x400
InstructionAccess:
EXCEPTION_PROLOG
mr r4,r12
mr r5,r9
EXC_XFER_EE_LITE(0x400, handle_page_fault)
/* External interrupt */
EXCEPTION(0x500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE)
/* Alignment exception */
. = 0x600
Alignment:
EXCEPTION_PROLOG
mfspr r4,SPRN_DAR
stw r4,_DAR(r11)
li r5,0x00f0
mtspr SPRN_DAR,r5 /* Tag DAR, to be used in DTLB Error */
mfspr r5,SPRN_DSISR
stw r5,_DSISR(r11)
addi r3,r1,STACK_FRAME_OVERHEAD
EXC_XFER_EE(0x600, alignment_exception)
/* Program check exception */
EXCEPTION(0x700, ProgramCheck, program_check_exception, EXC_XFER_STD)
/* No FPU on MPC8xx. This exception is not supposed to happen.
*/
EXCEPTION(0x800, FPUnavailable, unknown_exception, EXC_XFER_STD)
/* Decrementer */
EXCEPTION(0x900, Decrementer, timer_interrupt, EXC_XFER_LITE)
EXCEPTION(0xa00, Trap_0a, unknown_exception, EXC_XFER_EE)
EXCEPTION(0xb00, Trap_0b, unknown_exception, EXC_XFER_EE)
/* System call */
. = 0xc00
SystemCall:
EXCEPTION_PROLOG
EXC_XFER_EE_LITE(0xc00, DoSyscall)
/* Single step - not used on 601 */
EXCEPTION(0xd00, SingleStep, single_step_exception, EXC_XFER_STD)
EXCEPTION(0xe00, Trap_0e, unknown_exception, EXC_XFER_EE)
EXCEPTION(0xf00, Trap_0f, unknown_exception, EXC_XFER_EE)
/* On the MPC8xx, this is a software emulation interrupt. It occurs
* for all unimplemented and illegal instructions.
*/
EXCEPTION(0x1000, SoftEmu, SoftwareEmulation, EXC_XFER_STD)
. = 0x1100
/*
* For the MPC8xx, this is a software tablewalk to load the instruction
* TLB. It is modelled after the example in the Motorola manual. The task
* switch loads the M_TWB register with the pointer to the first level table.
* If we discover there is no second level table (value is zero) or if there
* is an invalid pte, we load that into the TLB, which causes another fault
* into the TLB Error interrupt where we can handle such problems.
* We have to use the MD_xxx registers for the tablewalk because the
* equivalent MI_xxx registers only perform the attribute functions.
*/
InstructionTLBMiss:
#ifdef CONFIG_8xx_CPU6
stw r3, 8(r0)
#endif
DO_8xx_CPU6(0x3f80, r3)
mtspr SPRN_M_TW, r10 /* Save a couple of working registers */
mfcr r10
#ifdef CONFIG_8xx_CPU6
stw r10, 0(r0)
stw r11, 4(r0)
#else
mtspr SPRN_DAR, r10
mtspr SPRN_SPRG2, r11
#endif
mfspr r10, SPRN_SRR0 /* Get effective address of fault */
#ifdef CONFIG_8xx_CPU15
addi r11, r10, 0x1000
tlbie r11
addi r11, r10, -0x1000
tlbie r11
#endif
DO_8xx_CPU6(0x3780, r3)
mtspr SPRN_MD_EPN, r10 /* Have to use MD_EPN for walk, MI_EPN can't */
mfspr r10, SPRN_M_TWB /* Get level 1 table entry address */
/* If we are faulting a kernel address, we have to use the
* kernel page tables.
*/
#ifdef CONFIG_MODULES
/* Only modules will cause ITLB Misses as we always
* pin the first 8MB of kernel memory */
andi. r11, r10, 0x0800 /* Address >= 0x80000000 */
beq 3f
lis r11, swapper_pg_dir@h
ori r11, r11, swapper_pg_dir@l
rlwimi r10, r11, 0, 2, 19
3:
#endif
lwz r11, 0(r10) /* Get the level 1 entry */
rlwinm. r10, r11,0,0,19 /* Extract page descriptor page address */
beq 2f /* If zero, don't try to find a pte */
/* We have a pte table, so load the MI_TWC with the attributes
* for this "segment."
*/
ori r11,r11,1 /* Set valid bit */
DO_8xx_CPU6(0x2b80, r3)
mtspr SPRN_MI_TWC, r11 /* Set segment attributes */
DO_8xx_CPU6(0x3b80, r3)
mtspr SPRN_MD_TWC, r11 /* Load pte table base address */
mfspr r11, SPRN_MD_TWC /* ....and get the pte address */
lwz r10, 0(r11) /* Get the pte */
#ifdef CONFIG_SWAP
andi. r11, r10, _PAGE_ACCESSED | _PAGE_PRESENT
cmpwi cr0, r11, _PAGE_ACCESSED | _PAGE_PRESENT
bne- cr0, 2f
#endif
/* The Linux PTE won't go exactly into the MMU TLB.
* Software indicator bits 21 and 28 must be clear.
* Software indicator bits 24, 25, 26, and 27 must be
* set. All other Linux PTE bits control the behavior
* of the MMU.
*/
li r11, 0x00f0
rlwimi r10, r11, 0, 0x07f8 /* Set 24-27, clear 21-23,28 */
DO_8xx_CPU6(0x2d80, r3)
mtspr SPRN_MI_RPN, r10 /* Update TLB entry */
/* Restore registers */
#ifndef CONFIG_8xx_CPU6
mfspr r10, SPRN_DAR
mtcr r10
mtspr SPRN_DAR, r11 /* Tag DAR */
mfspr r11, SPRN_SPRG2
#else
lwz r11, 0(r0)
mtcr r11
lwz r11, 4(r0)
lwz r3, 8(r0)
#endif
mfspr r10, SPRN_M_TW
rfi
2:
mfspr r11, SPRN_SRR1
/* clear all error bits as TLB Miss
* sets a few unconditionally
*/
rlwinm r11, r11, 0, 0xffff
mtspr SPRN_SRR1, r11
/* Restore registers */
#ifndef CONFIG_8xx_CPU6
mfspr r10, SPRN_DAR
mtcr r10
li r11, 0x00f0
mtspr SPRN_DAR, r11 /* Tag DAR */
mfspr r11, SPRN_SPRG2
#else
lwz r11, 0(r0)
mtcr r11
lwz r11, 4(r0)
lwz r3, 8(r0)
#endif
mfspr r10, SPRN_M_TW
b InstructionAccess
. = 0x1200
DataStoreTLBMiss:
#ifdef CONFIG_8xx_CPU6
stw r3, 8(r0)
#endif
DO_8xx_CPU6(0x3f80, r3)
mtspr SPRN_M_TW, r10 /* Save a couple of working registers */
mfcr r10
#ifdef CONFIG_8xx_CPU6
stw r10, 0(r0)
stw r11, 4(r0)
#else
mtspr SPRN_DAR, r10
mtspr SPRN_SPRG2, r11
#endif
mfspr r10, SPRN_M_TWB /* Get level 1 table entry address */
/* If we are faulting a kernel address, we have to use the
* kernel page tables.
*/
andi. r11, r10, 0x0800
beq 3f
lis r11, swapper_pg_dir@h
ori r11, r11, swapper_pg_dir@l
rlwimi r10, r11, 0, 2, 19
3:
lwz r11, 0(r10) /* Get the level 1 entry */
rlwinm. r10, r11,0,0,19 /* Extract page descriptor page address */
beq 2f /* If zero, don't try to find a pte */
/* We have a pte table, so load fetch the pte from the table.
*/
ori r11, r11, 1 /* Set valid bit in physical L2 page */
DO_8xx_CPU6(0x3b80, r3)
mtspr SPRN_MD_TWC, r11 /* Load pte table base address */
mfspr r10, SPRN_MD_TWC /* ....and get the pte address */
lwz r10, 0(r10) /* Get the pte */
/* Insert the Guarded flag into the TWC from the Linux PTE.
* It is bit 27 of both the Linux PTE and the TWC (at least
* I got that right :-). It will be better when we can put
* this into the Linux pgd/pmd and load it in the operation
* above.
*/
rlwimi r11, r10, 0, 27, 27
/* Insert the WriteThru flag into the TWC from the Linux PTE.
* It is bit 25 in the Linux PTE and bit 30 in the TWC
*/
rlwimi r11, r10, 32-5, 30, 30
DO_8xx_CPU6(0x3b80, r3)
mtspr SPRN_MD_TWC, r11
/* Both _PAGE_ACCESSED and _PAGE_PRESENT has to be set.
* We also need to know if the insn is a load/store, so:
* Clear _PAGE_PRESENT and load that which will
* trap into DTLB Error with store bit set accordinly.
*/
/* PRESENT=0x1, ACCESSED=0x20
* r11 = ((r10 & PRESENT) & ((r10 & ACCESSED) >> 5));
* r10 = (r10 & ~PRESENT) | r11;
*/
#ifdef CONFIG_SWAP
rlwinm r11, r10, 32-5, _PAGE_PRESENT
and r11, r11, r10
rlwimi r10, r11, 0, _PAGE_PRESENT
#endif
/* Honour kernel RO, User NA */
/* 0x200 == Extended encoding, bit 22 */
rlwimi r10, r10, 32-2, 0x200 /* Copy USER to bit 22, 0x200 */
/* r11 = (r10 & _PAGE_RW) >> 1 */
rlwinm r11, r10, 32-1, 0x200
or r10, r11, r10
/* invert RW and 0x200 bits */
xori r10, r10, _PAGE_RW | 0x200
/* The Linux PTE won't go exactly into the MMU TLB.
* Software indicator bits 22 and 28 must be clear.
* Software indicator bits 24, 25, 26, and 27 must be
* set. All other Linux PTE bits control the behavior
* of the MMU.
*/
2: li r11, 0x00f0
rlwimi r10, r11, 0, 24, 28 /* Set 24-27, clear 28 */
DO_8xx_CPU6(0x3d80, r3)
mtspr SPRN_MD_RPN, r10 /* Update TLB entry */
/* Restore registers */
#ifndef CONFIG_8xx_CPU6
mfspr r10, SPRN_DAR
mtcr r10
mtspr SPRN_DAR, r11 /* Tag DAR */
mfspr r11, SPRN_SPRG2
#else
mtspr SPRN_DAR, r11 /* Tag DAR */
lwz r11, 0(r0)
mtcr r11
lwz r11, 4(r0)
lwz r3, 8(r0)
#endif
mfspr r10, SPRN_M_TW
rfi
/* This is an instruction TLB error on the MPC8xx. This could be due
* to many reasons, such as executing guarded memory or illegal instruction
* addresses. There is nothing to do but handle a big time error fault.
*/
. = 0x1300
InstructionTLBError:
b InstructionAccess
/* This is the data TLB error on the MPC8xx. This could be due to
* many reasons, including a dirty update to a pte. We can catch that
* one here, but anything else is an error. First, we track down the
* Linux pte. If it is valid, write access is allowed, but the
* page dirty bit is not set, we will set it and reload the TLB. For
* any other case, we bail out to a higher level function that can
* handle it.
*/
. = 0x1400
DataTLBError:
#ifdef CONFIG_8xx_CPU6
stw r3, 8(r0)
#endif
DO_8xx_CPU6(0x3f80, r3)
mtspr SPRN_M_TW, r10 /* Save a couple of working registers */
mfcr r10
stw r10, 0(r0)
stw r11, 4(r0)
mfspr r10, SPRN_DAR
cmpwi cr0, r10, 0x00f0
beq- FixupDAR /* must be a buggy dcbX, icbi insn. */
DARFixed:/* Return from dcbx instruction bug workaround, r10 holds value of DAR */
mfspr r10, SPRN_M_TW /* Restore registers */
lwz r11, 0(r0)
mtcr r11
lwz r11, 4(r0)
#ifdef CONFIG_8xx_CPU6
lwz r3, 8(r0)
#endif
b DataAccess
EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1600, Trap_16, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1700, Trap_17, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1a00, Trap_1a, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1b00, Trap_1b, unknown_exception, EXC_XFER_EE)
/* On the MPC8xx, these next four traps are used for development
* support of breakpoints and such. Someday I will get around to
* using them.
*/
EXCEPTION(0x1c00, Trap_1c, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1d00, Trap_1d, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1e00, Trap_1e, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1f00, Trap_1f, unknown_exception, EXC_XFER_EE)
. = 0x2000
/* This is the procedure to calculate the data EA for buggy dcbx,dcbi instructions
* by decoding the registers used by the dcbx instruction and adding them.
* DAR is set to the calculated address and r10 also holds the EA on exit.
*/
/* define if you don't want to use self modifying code */
#define NO_SELF_MODIFYING_CODE
FixupDAR:/* Entry point for dcbx workaround. */
/* fetch instruction from memory. */
mfspr r10, SPRN_SRR0
andis. r11, r10, 0x8000 /* Address >= 0x80000000 */
DO_8xx_CPU6(0x3780, r3)
mtspr SPRN_MD_EPN, r10
mfspr r11, SPRN_M_TWB /* Get level 1 table entry address */
beq- 3f /* Branch if user space */
lis r11, (swapper_pg_dir-PAGE_OFFSET)@h
ori r11, r11, (swapper_pg_dir-PAGE_OFFSET)@l
rlwimi r11, r10, 32-20, 0xffc /* r11 = r11&~0xffc|(r10>>20)&0xffc */
3: lwz r11, 0(r11) /* Get the level 1 entry */
DO_8xx_CPU6(0x3b80, r3)
mtspr SPRN_MD_TWC, r11 /* Load pte table base address */
mfspr r11, SPRN_MD_TWC /* ....and get the pte address */
lwz r11, 0(r11) /* Get the pte */
/* concat physical page address(r11) and page offset(r10) */
rlwimi r11, r10, 0, 20, 31
lwz r11,0(r11)
/* Check if it really is a dcbx instruction. */
/* dcbt and dcbtst does not generate DTLB Misses/Errors,
* no need to include them here */
srwi r10, r11, 26 /* check if major OP code is 31 */
cmpwi cr0, r10, 31
bne- 141f
rlwinm r10, r11, 0, 21, 30
cmpwi cr0, r10, 2028 /* Is dcbz? */
beq+ 142f
cmpwi cr0, r10, 940 /* Is dcbi? */
beq+ 142f
cmpwi cr0, r10, 108 /* Is dcbst? */
beq+ 144f /* Fix up store bit! */
cmpwi cr0, r10, 172 /* Is dcbf? */
beq+ 142f
cmpwi cr0, r10, 1964 /* Is icbi? */
beq+ 142f
141: mfspr r10, SPRN_DAR /* r10 must hold DAR at exit */
b DARFixed /* Nope, go back to normal TLB processing */
144: mfspr r10, SPRN_DSISR
rlwinm r10, r10,0,7,5 /* Clear store bit for buggy dcbst insn */
mtspr SPRN_DSISR, r10
142: /* continue, it was a dcbx, dcbi instruction. */
#ifdef CONFIG_8xx_CPU6
lwz r3, 8(r0) /* restore r3 from memory */
#endif
#ifndef NO_SELF_MODIFYING_CODE
andis. r10,r11,0x1f /* test if reg RA is r0 */
li r10,modified_instr@l
dcbtst r0,r10 /* touch for store */
rlwinm r11,r11,0,0,20 /* Zero lower 10 bits */
oris r11,r11,640 /* Transform instr. to a "add r10,RA,RB" */
ori r11,r11,532
stw r11,0(r10) /* store add/and instruction */
dcbf 0,r10 /* flush new instr. to memory. */
icbi 0,r10 /* invalidate instr. cache line */
lwz r11, 4(r0) /* restore r11 from memory */
mfspr r10, SPRN_M_TW /* restore r10 from M_TW */
isync /* Wait until new instr is loaded from memory */
modified_instr:
.space 4 /* this is where the add instr. is stored */
bne+ 143f
subf r10,r0,r10 /* r10=r10-r0, only if reg RA is r0 */
143: mtdar r10 /* store faulting EA in DAR */
b DARFixed /* Go back to normal TLB handling */
#else
mfctr r10
mtdar r10 /* save ctr reg in DAR */
rlwinm r10, r11, 24, 24, 28 /* offset into jump table for reg RB */
addi r10, r10, 150f@l /* add start of table */
mtctr r10 /* load ctr with jump address */
xor r10, r10, r10 /* sum starts at zero */
bctr /* jump into table */
150:
add r10, r10, r0 ;b 151f
add r10, r10, r1 ;b 151f
add r10, r10, r2 ;b 151f
add r10, r10, r3 ;b 151f
add r10, r10, r4 ;b 151f
add r10, r10, r5 ;b 151f
add r10, r10, r6 ;b 151f
add r10, r10, r7 ;b 151f
add r10, r10, r8 ;b 151f
add r10, r10, r9 ;b 151f
mtctr r11 ;b 154f /* r10 needs special handling */
mtctr r11 ;b 153f /* r11 needs special handling */
add r10, r10, r12 ;b 151f
add r10, r10, r13 ;b 151f
add r10, r10, r14 ;b 151f
add r10, r10, r15 ;b 151f
add r10, r10, r16 ;b 151f
add r10, r10, r17 ;b 151f
add r10, r10, r18 ;b 151f
add r10, r10, r19 ;b 151f
add r10, r10, r20 ;b 151f
add r10, r10, r21 ;b 151f
add r10, r10, r22 ;b 151f
add r10, r10, r23 ;b 151f
add r10, r10, r24 ;b 151f
add r10, r10, r25 ;b 151f
add r10, r10, r26 ;b 151f
add r10, r10, r27 ;b 151f
add r10, r10, r28 ;b 151f
add r10, r10, r29 ;b 151f
add r10, r10, r30 ;b 151f
add r10, r10, r31
151:
rlwinm. r11,r11,19,24,28 /* offset into jump table for reg RA */
beq 152f /* if reg RA is zero, don't add it */
addi r11, r11, 150b@l /* add start of table */
mtctr r11 /* load ctr with jump address */
rlwinm r11,r11,0,16,10 /* make sure we don't execute this more than once */
bctr /* jump into table */
152:
mfdar r11
mtctr r11 /* restore ctr reg from DAR */
mtdar r10 /* save fault EA to DAR */
b DARFixed /* Go back to normal TLB handling */
/* special handling for r10,r11 since these are modified already */
153: lwz r11, 4(r0) /* load r11 from memory */
b 155f
154: mfspr r11, SPRN_M_TW /* load r10 from M_TW */
155: add r10, r10, r11 /* add it */
mfctr r11 /* restore r11 */
b 151b
#endif
.globl giveup_fpu
giveup_fpu:
blr
/*
* This is where the main kernel code starts.
*/
start_here:
/* ptr to current */
lis r2,init_task@h
ori r2,r2,init_task@l
/* ptr to phys current thread */
tophys(r4,r2)
addi r4,r4,THREAD /* init task's THREAD */
mtspr SPRN_SPRG_THREAD,r4
/* stack */
lis r1,init_thread_union@ha
addi r1,r1,init_thread_union@l
li r0,0
stwu r0,THREAD_SIZE-STACK_FRAME_OVERHEAD(r1)
bl early_init /* We have to do this with MMU on */
/*
* Decide what sort of machine this is and initialize the MMU.
*/
mr r3,r31
mr r4,r30
mr r5,r29
mr r6,r28
mr r7,r27
bl machine_init
bl MMU_init
/*
* Go back to running unmapped so we can load up new values
* and change to using our exception vectors.
* On the 8xx, all we have to do is invalidate the TLB to clear
* the old 8M byte TLB mappings and load the page table base register.
*/
/* The right way to do this would be to track it down through
* init's THREAD like the context switch code does, but this is
* easier......until someone changes init's static structures.
*/
lis r6, swapper_pg_dir@h
ori r6, r6, swapper_pg_dir@l
tophys(r6,r6)
#ifdef CONFIG_8xx_CPU6
lis r4, cpu6_errata_word@h
ori r4, r4, cpu6_errata_word@l
li r3, 0x3980
stw r3, 12(r4)
lwz r3, 12(r4)
#endif
mtspr SPRN_M_TWB, r6
lis r4,2f@h
ori r4,r4,2f@l
tophys(r4,r4)
li r3,MSR_KERNEL & ~(MSR_IR|MSR_DR)
mtspr SPRN_SRR0,r4
mtspr SPRN_SRR1,r3
rfi
/* Load up the kernel context */
2:
SYNC /* Force all PTE updates to finish */
tlbia /* Clear all TLB entries */
sync /* wait for tlbia/tlbie to finish */
TLBSYNC /* ... on all CPUs */
/* set up the PTE pointers for the Abatron bdiGDB.
*/
tovirt(r6,r6)
lis r5, abatron_pteptrs@h
ori r5, r5, abatron_pteptrs@l
stw r5, 0xf0(r0) /* Must match your Abatron config file */
tophys(r5,r5)
stw r6, 0(r5)
/* Now turn on the MMU for real! */
li r4,MSR_KERNEL
lis r3,start_kernel@h
ori r3,r3,start_kernel@l
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
rfi /* enable MMU and jump to start_kernel */
/* Set up the initial MMU state so we can do the first level of
* kernel initialization. This maps the first 8 MBytes of memory 1:1
* virtual to physical. Also, set the cache mode since that is defined
* by TLB entries and perform any additional mapping (like of the IMMR).
* If configured to pin some TLBs, we pin the first 8 Mbytes of kernel,
* 24 Mbytes of data, and the 8M IMMR space. Anything not covered by
* these mappings is mapped by page tables.
*/
initial_mmu:
tlbia /* Invalidate all TLB entries */
/* Always pin the first 8 MB ITLB to prevent ITLB
misses while mucking around with SRR0/SRR1 in asm
*/
lis r8, MI_RSV4I@h
ori r8, r8, 0x1c00
mtspr SPRN_MI_CTR, r8 /* Set instruction MMU control */
#ifdef CONFIG_PIN_TLB
lis r10, (MD_RSV4I | MD_RESETVAL)@h
ori r10, r10, 0x1c00
mr r8, r10
#else
lis r10, MD_RESETVAL@h
#endif
#ifndef CONFIG_8xx_COPYBACK
oris r10, r10, MD_WTDEF@h
#endif
mtspr SPRN_MD_CTR, r10 /* Set data TLB control */
/* Now map the lower 8 Meg into the TLBs. For this quick hack,
* we can load the instruction and data TLB registers with the
* same values.
*/
lis r8, KERNELBASE@h /* Create vaddr for TLB */
ori r8, r8, MI_EVALID /* Mark it valid */
mtspr SPRN_MI_EPN, r8
mtspr SPRN_MD_EPN, r8
li r8, MI_PS8MEG /* Set 8M byte page */
ori r8, r8, MI_SVALID /* Make it valid */
mtspr SPRN_MI_TWC, r8
mtspr SPRN_MD_TWC, r8
li r8, MI_BOOTINIT /* Create RPN for address 0 */
mtspr SPRN_MI_RPN, r8 /* Store TLB entry */
mtspr SPRN_MD_RPN, r8
lis r8, MI_Kp@h /* Set the protection mode */
mtspr SPRN_MI_AP, r8
mtspr SPRN_MD_AP, r8
/* Map another 8 MByte at the IMMR to get the processor
* internal registers (among other things).
*/
#ifdef CONFIG_PIN_TLB
addi r10, r10, 0x0100
mtspr SPRN_MD_CTR, r10
#endif
mfspr r9, 638 /* Get current IMMR */
andis. r9, r9, 0xff80 /* Get 8Mbyte boundary */
mr r8, r9 /* Create vaddr for TLB */
ori r8, r8, MD_EVALID /* Mark it valid */
mtspr SPRN_MD_EPN, r8
li r8, MD_PS8MEG /* Set 8M byte page */
ori r8, r8, MD_SVALID /* Make it valid */
mtspr SPRN_MD_TWC, r8
mr r8, r9 /* Create paddr for TLB */
ori r8, r8, MI_BOOTINIT|0x2 /* Inhibit cache -- Cort */
mtspr SPRN_MD_RPN, r8
#ifdef CONFIG_PIN_TLB
/* Map two more 8M kernel data pages.
*/
addi r10, r10, 0x0100
mtspr SPRN_MD_CTR, r10
lis r8, KERNELBASE@h /* Create vaddr for TLB */
addis r8, r8, 0x0080 /* Add 8M */
ori r8, r8, MI_EVALID /* Mark it valid */
mtspr SPRN_MD_EPN, r8
li r9, MI_PS8MEG /* Set 8M byte page */
ori r9, r9, MI_SVALID /* Make it valid */
mtspr SPRN_MD_TWC, r9
li r11, MI_BOOTINIT /* Create RPN for address 0 */
addis r11, r11, 0x0080 /* Add 8M */
mtspr SPRN_MD_RPN, r11
addis r8, r8, 0x0080 /* Add 8M */
mtspr SPRN_MD_EPN, r8
mtspr SPRN_MD_TWC, r9
addis r11, r11, 0x0080 /* Add 8M */
mtspr SPRN_MD_RPN, r11
#endif
/* Since the cache is enabled according to the information we
* just loaded into the TLB, invalidate and enable the caches here.
* We should probably check/set other modes....later.
*/
lis r8, IDC_INVALL@h
mtspr SPRN_IC_CST, r8
mtspr SPRN_DC_CST, r8
lis r8, IDC_ENABLE@h
mtspr SPRN_IC_CST, r8
#ifdef CONFIG_8xx_COPYBACK
mtspr SPRN_DC_CST, r8
#else
/* For a debug option, I left this here to easily enable
* the write through cache mode
*/
lis r8, DC_SFWT@h
mtspr SPRN_DC_CST, r8
lis r8, IDC_ENABLE@h
mtspr SPRN_DC_CST, r8
#endif
blr
/*
* Set up to use a given MMU context.
* r3 is context number, r4 is PGD pointer.
*
* We place the physical address of the new task page directory loaded
* into the MMU base register, and set the ASID compare register with
* the new "context."
*/
_GLOBAL(set_context)
#ifdef CONFIG_BDI_SWITCH
/* Context switch the PTE pointer for the Abatron BDI2000.
* The PGDIR is passed as second argument.
*/
lis r5, KERNELBASE@h
lwz r5, 0xf0(r5)
stw r4, 0x4(r5)
#endif
#ifdef CONFIG_8xx_CPU6
lis r6, cpu6_errata_word@h
ori r6, r6, cpu6_errata_word@l
tophys (r4, r4)
li r7, 0x3980
stw r7, 12(r6)
lwz r7, 12(r6)
mtspr SPRN_M_TWB, r4 /* Update MMU base address */
li r7, 0x3380
stw r7, 12(r6)
lwz r7, 12(r6)
mtspr SPRN_M_CASID, r3 /* Update context */
#else
mtspr SPRN_M_CASID,r3 /* Update context */
tophys (r4, r4)
mtspr SPRN_M_TWB, r4 /* and pgd */
#endif
SYNC
blr
#ifdef CONFIG_8xx_CPU6
/* It's here because it is unique to the 8xx.
* It is important we get called with interrupts disabled. I used to
* do that, but it appears that all code that calls this already had
* interrupt disabled.
*/
.globl set_dec_cpu6
set_dec_cpu6:
lis r7, cpu6_errata_word@h
ori r7, r7, cpu6_errata_word@l
li r4, 0x2c00
stw r4, 8(r7)
lwz r4, 8(r7)
mtspr 22, r3 /* Update Decrementer */
SYNC
blr
#endif
/*
* We put a few things here that have to be page-aligned.
* This stuff goes at the beginning of the data segment,
* which is page-aligned.
*/
.data
.globl sdata
sdata:
.globl empty_zero_page
empty_zero_page:
.space 4096
.globl swapper_pg_dir
swapper_pg_dir:
.space 4096
/* Room for two PTE table poiners, usually the kernel and current user
* pointer to their respective root page table (pgdir).
*/
abatron_pteptrs:
.space 8
#ifdef CONFIG_8xx_CPU6
.globl cpu6_errata_word
cpu6_errata_word:
.space 16
#endif