linux/drivers/bluetooth/ath3k.c
Sarah Sharp e1f12eb6ba USB: Disable hub-initiated LPM for comms devices.
Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-05-18 15:42:55 -07:00

452 lines
11 KiB
C

/*
* Copyright (c) 2008-2009 Atheros Communications Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/device.h>
#include <linux/firmware.h>
#include <linux/usb.h>
#include <net/bluetooth/bluetooth.h>
#define VERSION "1.0"
#define ATH3K_FIRMWARE "ath3k-1.fw"
#define ATH3K_DNLOAD 0x01
#define ATH3K_GETSTATE 0x05
#define ATH3K_SET_NORMAL_MODE 0x07
#define ATH3K_GETVERSION 0x09
#define USB_REG_SWITCH_VID_PID 0x0a
#define ATH3K_MODE_MASK 0x3F
#define ATH3K_NORMAL_MODE 0x0E
#define ATH3K_PATCH_UPDATE 0x80
#define ATH3K_SYSCFG_UPDATE 0x40
#define ATH3K_XTAL_FREQ_26M 0x00
#define ATH3K_XTAL_FREQ_40M 0x01
#define ATH3K_XTAL_FREQ_19P2 0x02
#define ATH3K_NAME_LEN 0xFF
struct ath3k_version {
unsigned int rom_version;
unsigned int build_version;
unsigned int ram_version;
unsigned char ref_clock;
unsigned char reserved[0x07];
};
static struct usb_device_id ath3k_table[] = {
/* Atheros AR3011 */
{ USB_DEVICE(0x0CF3, 0x3000) },
/* Atheros AR3011 with sflash firmware*/
{ USB_DEVICE(0x0CF3, 0x3002) },
{ USB_DEVICE(0x13d3, 0x3304) },
{ USB_DEVICE(0x0930, 0x0215) },
{ USB_DEVICE(0x0489, 0xE03D) },
/* Atheros AR9285 Malbec with sflash firmware */
{ USB_DEVICE(0x03F0, 0x311D) },
/* Atheros AR3012 with sflash firmware*/
{ USB_DEVICE(0x0CF3, 0x3004) },
{ USB_DEVICE(0x0CF3, 0x311D) },
{ USB_DEVICE(0x13d3, 0x3375) },
{ USB_DEVICE(0x04CA, 0x3005) },
{ USB_DEVICE(0x13d3, 0x3362) },
{ USB_DEVICE(0x0CF3, 0xE004) },
/* Atheros AR5BBU12 with sflash firmware */
{ USB_DEVICE(0x0489, 0xE02C) },
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, ath3k_table);
#define BTUSB_ATH3012 0x80
/* This table is to load patch and sysconfig files
* for AR3012 */
static struct usb_device_id ath3k_blist_tbl[] = {
/* Atheros AR3012 with sflash firmware*/
{ USB_DEVICE(0x0cf3, 0x3004), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0x311D), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3005), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
{ } /* Terminating entry */
};
#define USB_REQ_DFU_DNLOAD 1
#define BULK_SIZE 4096
#define FW_HDR_SIZE 20
static int ath3k_load_firmware(struct usb_device *udev,
const struct firmware *firmware)
{
u8 *send_buf;
int err, pipe, len, size, sent = 0;
int count = firmware->size;
BT_DBG("udev %p", udev);
pipe = usb_sndctrlpipe(udev, 0);
send_buf = kmalloc(BULK_SIZE, GFP_KERNEL);
if (!send_buf) {
BT_ERR("Can't allocate memory chunk for firmware");
return -ENOMEM;
}
memcpy(send_buf, firmware->data, 20);
if ((err = usb_control_msg(udev, pipe,
USB_REQ_DFU_DNLOAD,
USB_TYPE_VENDOR, 0, 0,
send_buf, 20, USB_CTRL_SET_TIMEOUT)) < 0) {
BT_ERR("Can't change to loading configuration err");
goto error;
}
sent += 20;
count -= 20;
while (count) {
size = min_t(uint, count, BULK_SIZE);
pipe = usb_sndbulkpipe(udev, 0x02);
memcpy(send_buf, firmware->data + sent, size);
err = usb_bulk_msg(udev, pipe, send_buf, size,
&len, 3000);
if (err || (len != size)) {
BT_ERR("Error in firmware loading err = %d,"
"len = %d, size = %d", err, len, size);
goto error;
}
sent += size;
count -= size;
}
error:
kfree(send_buf);
return err;
}
static int ath3k_get_state(struct usb_device *udev, unsigned char *state)
{
int pipe = 0;
pipe = usb_rcvctrlpipe(udev, 0);
return usb_control_msg(udev, pipe, ATH3K_GETSTATE,
USB_TYPE_VENDOR | USB_DIR_IN, 0, 0,
state, 0x01, USB_CTRL_SET_TIMEOUT);
}
static int ath3k_get_version(struct usb_device *udev,
struct ath3k_version *version)
{
int pipe = 0;
pipe = usb_rcvctrlpipe(udev, 0);
return usb_control_msg(udev, pipe, ATH3K_GETVERSION,
USB_TYPE_VENDOR | USB_DIR_IN, 0, 0, version,
sizeof(struct ath3k_version),
USB_CTRL_SET_TIMEOUT);
}
static int ath3k_load_fwfile(struct usb_device *udev,
const struct firmware *firmware)
{
u8 *send_buf;
int err, pipe, len, size, count, sent = 0;
int ret;
count = firmware->size;
send_buf = kmalloc(BULK_SIZE, GFP_KERNEL);
if (!send_buf) {
BT_ERR("Can't allocate memory chunk for firmware");
return -ENOMEM;
}
size = min_t(uint, count, FW_HDR_SIZE);
memcpy(send_buf, firmware->data, size);
pipe = usb_sndctrlpipe(udev, 0);
ret = usb_control_msg(udev, pipe, ATH3K_DNLOAD,
USB_TYPE_VENDOR, 0, 0, send_buf,
size, USB_CTRL_SET_TIMEOUT);
if (ret < 0) {
BT_ERR("Can't change to loading configuration err");
kfree(send_buf);
return ret;
}
sent += size;
count -= size;
while (count) {
size = min_t(uint, count, BULK_SIZE);
pipe = usb_sndbulkpipe(udev, 0x02);
memcpy(send_buf, firmware->data + sent, size);
err = usb_bulk_msg(udev, pipe, send_buf, size,
&len, 3000);
if (err || (len != size)) {
BT_ERR("Error in firmware loading err = %d,"
"len = %d, size = %d", err, len, size);
kfree(send_buf);
return err;
}
sent += size;
count -= size;
}
kfree(send_buf);
return 0;
}
static int ath3k_switch_pid(struct usb_device *udev)
{
int pipe = 0;
pipe = usb_sndctrlpipe(udev, 0);
return usb_control_msg(udev, pipe, USB_REG_SWITCH_VID_PID,
USB_TYPE_VENDOR, 0, 0,
NULL, 0, USB_CTRL_SET_TIMEOUT);
}
static int ath3k_set_normal_mode(struct usb_device *udev)
{
unsigned char fw_state;
int pipe = 0, ret;
ret = ath3k_get_state(udev, &fw_state);
if (ret < 0) {
BT_ERR("Can't get state to change to normal mode err");
return ret;
}
if ((fw_state & ATH3K_MODE_MASK) == ATH3K_NORMAL_MODE) {
BT_DBG("firmware was already in normal mode");
return 0;
}
pipe = usb_sndctrlpipe(udev, 0);
return usb_control_msg(udev, pipe, ATH3K_SET_NORMAL_MODE,
USB_TYPE_VENDOR, 0, 0,
NULL, 0, USB_CTRL_SET_TIMEOUT);
}
static int ath3k_load_patch(struct usb_device *udev)
{
unsigned char fw_state;
char filename[ATH3K_NAME_LEN] = {0};
const struct firmware *firmware;
struct ath3k_version fw_version, pt_version;
int ret;
ret = ath3k_get_state(udev, &fw_state);
if (ret < 0) {
BT_ERR("Can't get state to change to load ram patch err");
return ret;
}
if (fw_state & ATH3K_PATCH_UPDATE) {
BT_DBG("Patch was already downloaded");
return 0;
}
ret = ath3k_get_version(udev, &fw_version);
if (ret < 0) {
BT_ERR("Can't get version to change to load ram patch err");
return ret;
}
snprintf(filename, ATH3K_NAME_LEN, "ar3k/AthrBT_0x%08x.dfu",
fw_version.rom_version);
ret = request_firmware(&firmware, filename, &udev->dev);
if (ret < 0) {
BT_ERR("Patch file not found %s", filename);
return ret;
}
pt_version.rom_version = *(int *)(firmware->data + firmware->size - 8);
pt_version.build_version = *(int *)
(firmware->data + firmware->size - 4);
if ((pt_version.rom_version != fw_version.rom_version) ||
(pt_version.build_version <= fw_version.build_version)) {
BT_ERR("Patch file version did not match with firmware");
release_firmware(firmware);
return -EINVAL;
}
ret = ath3k_load_fwfile(udev, firmware);
release_firmware(firmware);
return ret;
}
static int ath3k_load_syscfg(struct usb_device *udev)
{
unsigned char fw_state;
char filename[ATH3K_NAME_LEN] = {0};
const struct firmware *firmware;
struct ath3k_version fw_version;
int clk_value, ret;
ret = ath3k_get_state(udev, &fw_state);
if (ret < 0) {
BT_ERR("Can't get state to change to load configration err");
return -EBUSY;
}
ret = ath3k_get_version(udev, &fw_version);
if (ret < 0) {
BT_ERR("Can't get version to change to load ram patch err");
return ret;
}
switch (fw_version.ref_clock) {
case ATH3K_XTAL_FREQ_26M:
clk_value = 26;
break;
case ATH3K_XTAL_FREQ_40M:
clk_value = 40;
break;
case ATH3K_XTAL_FREQ_19P2:
clk_value = 19;
break;
default:
clk_value = 0;
break;
}
snprintf(filename, ATH3K_NAME_LEN, "ar3k/ramps_0x%08x_%d%s",
fw_version.rom_version, clk_value, ".dfu");
ret = request_firmware(&firmware, filename, &udev->dev);
if (ret < 0) {
BT_ERR("Configuration file not found %s", filename);
return ret;
}
ret = ath3k_load_fwfile(udev, firmware);
release_firmware(firmware);
return ret;
}
static int ath3k_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
const struct firmware *firmware;
struct usb_device *udev = interface_to_usbdev(intf);
int ret;
BT_DBG("intf %p id %p", intf, id);
if (intf->cur_altsetting->desc.bInterfaceNumber != 0)
return -ENODEV;
/* match device ID in ath3k blacklist table */
if (!id->driver_info) {
const struct usb_device_id *match;
match = usb_match_id(intf, ath3k_blist_tbl);
if (match)
id = match;
}
/* load patch and sysconfig files for AR3012 */
if (id->driver_info & BTUSB_ATH3012) {
/* New firmware with patch and sysconfig files already loaded */
if (le16_to_cpu(udev->descriptor.bcdDevice) > 0x0001)
return -ENODEV;
ret = ath3k_load_patch(udev);
if (ret < 0) {
BT_ERR("Loading patch file failed");
return ret;
}
ret = ath3k_load_syscfg(udev);
if (ret < 0) {
BT_ERR("Loading sysconfig file failed");
return ret;
}
ret = ath3k_set_normal_mode(udev);
if (ret < 0) {
BT_ERR("Set normal mode failed");
return ret;
}
ath3k_switch_pid(udev);
return 0;
}
ret = request_firmware(&firmware, ATH3K_FIRMWARE, &udev->dev);
if (ret < 0) {
if (ret == -ENOENT)
BT_ERR("Firmware file \"%s\" not found",
ATH3K_FIRMWARE);
else
BT_ERR("Firmware file \"%s\" request failed (err=%d)",
ATH3K_FIRMWARE, ret);
return ret;
}
ret = ath3k_load_firmware(udev, firmware);
release_firmware(firmware);
return ret;
}
static void ath3k_disconnect(struct usb_interface *intf)
{
BT_DBG("ath3k_disconnect intf %p", intf);
}
static struct usb_driver ath3k_driver = {
.name = "ath3k",
.probe = ath3k_probe,
.disconnect = ath3k_disconnect,
.id_table = ath3k_table,
.disable_hub_initiated_lpm = 1,
};
module_usb_driver(ath3k_driver);
MODULE_AUTHOR("Atheros Communications");
MODULE_DESCRIPTION("Atheros AR30xx firmware driver");
MODULE_VERSION(VERSION);
MODULE_LICENSE("GPL");
MODULE_FIRMWARE(ATH3K_FIRMWARE);