linux/drivers/spi/spi-orion.c
Jan Kundrát fb9acf5f1f
spi: orion: fix CS GPIO handling again
The code did not de-assert any CS GPIOs before probing slaves. This
means that several CS signals could be active at once, garbling the
communication. Whether this was actually a problem depended on the type
of the SPI device attached (so my "spidev" for userspace access worked
correctly because its probe was effectively a no-op), and on the state
of the GPIO pins at SoC's boot.

The code was already iterating through all DT children of the SPI
controller, so this change re-uses that loop for CS GPIO setup as well.
This means that this might change the number of the HW CS signal which
is picked for all GPIO CS devices. Previously, the lowest one was used,
but we now use the first one from the DT.

With this move of the code, we can also finally initialize each GPIO CS
lane before registering the SPI controller (which in turn probes for
slaves).

I tried to fix this in 544248623b already, but that only did it half
way by registering the GPIOs properly. That patch failed to set their
logic signals early enough, though.

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-06-19 13:06:51 +01:00

856 lines
21 KiB
C

/*
* Marvell Orion SPI controller driver
*
* Author: Shadi Ammouri <shadi@marvell.com>
* Copyright (C) 2007-2008 Marvell Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/spi/spi.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
#include <linux/clk.h>
#include <linux/sizes.h>
#include <linux/gpio.h>
#include <asm/unaligned.h>
#define DRIVER_NAME "orion_spi"
/* Runtime PM autosuspend timeout: PM is fairly light on this driver */
#define SPI_AUTOSUSPEND_TIMEOUT 200
/* Some SoCs using this driver support up to 8 chip selects.
* It is up to the implementer to only use the chip selects
* that are available.
*/
#define ORION_NUM_CHIPSELECTS 8
#define ORION_SPI_WAIT_RDY_MAX_LOOP 2000 /* in usec */
#define ORION_SPI_IF_CTRL_REG 0x00
#define ORION_SPI_IF_CONFIG_REG 0x04
#define ORION_SPI_IF_RXLSBF BIT(14)
#define ORION_SPI_IF_TXLSBF BIT(13)
#define ORION_SPI_DATA_OUT_REG 0x08
#define ORION_SPI_DATA_IN_REG 0x0c
#define ORION_SPI_INT_CAUSE_REG 0x10
#define ORION_SPI_TIMING_PARAMS_REG 0x18
/* Register for the "Direct Mode" */
#define SPI_DIRECT_WRITE_CONFIG_REG 0x20
#define ORION_SPI_TMISO_SAMPLE_MASK (0x3 << 6)
#define ORION_SPI_TMISO_SAMPLE_1 (1 << 6)
#define ORION_SPI_TMISO_SAMPLE_2 (2 << 6)
#define ORION_SPI_MODE_CPOL (1 << 11)
#define ORION_SPI_MODE_CPHA (1 << 12)
#define ORION_SPI_IF_8_16_BIT_MODE (1 << 5)
#define ORION_SPI_CLK_PRESCALE_MASK 0x1F
#define ARMADA_SPI_CLK_PRESCALE_MASK 0xDF
#define ORION_SPI_MODE_MASK (ORION_SPI_MODE_CPOL | \
ORION_SPI_MODE_CPHA)
#define ORION_SPI_CS_MASK 0x1C
#define ORION_SPI_CS_SHIFT 2
#define ORION_SPI_CS(cs) ((cs << ORION_SPI_CS_SHIFT) & \
ORION_SPI_CS_MASK)
enum orion_spi_type {
ORION_SPI,
ARMADA_SPI,
};
struct orion_spi_dev {
enum orion_spi_type typ;
/*
* min_divisor and max_hz should be exclusive, the only we can
* have both is for managing the armada-370-spi case with old
* device tree
*/
unsigned long max_hz;
unsigned int min_divisor;
unsigned int max_divisor;
u32 prescale_mask;
bool is_errata_50mhz_ac;
};
struct orion_direct_acc {
void __iomem *vaddr;
u32 size;
};
struct orion_child_options {
struct orion_direct_acc direct_access;
};
struct orion_spi {
struct spi_master *master;
void __iomem *base;
struct clk *clk;
struct clk *axi_clk;
const struct orion_spi_dev *devdata;
int unused_hw_gpio;
struct orion_child_options child[ORION_NUM_CHIPSELECTS];
};
static inline void __iomem *spi_reg(struct orion_spi *orion_spi, u32 reg)
{
return orion_spi->base + reg;
}
static inline void
orion_spi_setbits(struct orion_spi *orion_spi, u32 reg, u32 mask)
{
void __iomem *reg_addr = spi_reg(orion_spi, reg);
u32 val;
val = readl(reg_addr);
val |= mask;
writel(val, reg_addr);
}
static inline void
orion_spi_clrbits(struct orion_spi *orion_spi, u32 reg, u32 mask)
{
void __iomem *reg_addr = spi_reg(orion_spi, reg);
u32 val;
val = readl(reg_addr);
val &= ~mask;
writel(val, reg_addr);
}
static int orion_spi_baudrate_set(struct spi_device *spi, unsigned int speed)
{
u32 tclk_hz;
u32 rate;
u32 prescale;
u32 reg;
struct orion_spi *orion_spi;
const struct orion_spi_dev *devdata;
orion_spi = spi_master_get_devdata(spi->master);
devdata = orion_spi->devdata;
tclk_hz = clk_get_rate(orion_spi->clk);
if (devdata->typ == ARMADA_SPI) {
/*
* Given the core_clk (tclk_hz) and the target rate (speed) we
* determine the best values for SPR (in [0 .. 15]) and SPPR (in
* [0..7]) such that
*
* core_clk / (SPR * 2 ** SPPR)
*
* is as big as possible but not bigger than speed.
*/
/* best integer divider: */
unsigned divider = DIV_ROUND_UP(tclk_hz, speed);
unsigned spr, sppr;
if (divider < 16) {
/* This is the easy case, divider is less than 16 */
spr = divider;
sppr = 0;
} else {
unsigned two_pow_sppr;
/*
* Find the highest bit set in divider. This and the
* three next bits define SPR (apart from rounding).
* SPPR is then the number of zero bits that must be
* appended:
*/
sppr = fls(divider) - 4;
/*
* As SPR only has 4 bits, we have to round divider up
* to the next multiple of 2 ** sppr.
*/
two_pow_sppr = 1 << sppr;
divider = (divider + two_pow_sppr - 1) & -two_pow_sppr;
/*
* recalculate sppr as rounding up divider might have
* increased it enough to change the position of the
* highest set bit. In this case the bit that now
* doesn't make it into SPR is 0, so there is no need to
* round again.
*/
sppr = fls(divider) - 4;
spr = divider >> sppr;
/*
* Now do range checking. SPR is constructed to have a
* width of 4 bits, so this is fine for sure. So we
* still need to check for sppr to fit into 3 bits:
*/
if (sppr > 7)
return -EINVAL;
}
prescale = ((sppr & 0x6) << 5) | ((sppr & 0x1) << 4) | spr;
} else {
/*
* the supported rates are: 4,6,8...30
* round up as we look for equal or less speed
*/
rate = DIV_ROUND_UP(tclk_hz, speed);
rate = roundup(rate, 2);
/* check if requested speed is too small */
if (rate > 30)
return -EINVAL;
if (rate < 4)
rate = 4;
/* Convert the rate to SPI clock divisor value. */
prescale = 0x10 + rate/2;
}
reg = readl(spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
reg = ((reg & ~devdata->prescale_mask) | prescale);
writel(reg, spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
return 0;
}
static void
orion_spi_mode_set(struct spi_device *spi)
{
u32 reg;
struct orion_spi *orion_spi;
orion_spi = spi_master_get_devdata(spi->master);
reg = readl(spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
reg &= ~ORION_SPI_MODE_MASK;
if (spi->mode & SPI_CPOL)
reg |= ORION_SPI_MODE_CPOL;
if (spi->mode & SPI_CPHA)
reg |= ORION_SPI_MODE_CPHA;
if (spi->mode & SPI_LSB_FIRST)
reg |= ORION_SPI_IF_RXLSBF | ORION_SPI_IF_TXLSBF;
else
reg &= ~(ORION_SPI_IF_RXLSBF | ORION_SPI_IF_TXLSBF);
writel(reg, spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
}
static void
orion_spi_50mhz_ac_timing_erratum(struct spi_device *spi, unsigned int speed)
{
u32 reg;
struct orion_spi *orion_spi;
orion_spi = spi_master_get_devdata(spi->master);
/*
* Erratum description: (Erratum NO. FE-9144572) The device
* SPI interface supports frequencies of up to 50 MHz.
* However, due to this erratum, when the device core clock is
* 250 MHz and the SPI interfaces is configured for 50MHz SPI
* clock and CPOL=CPHA=1 there might occur data corruption on
* reads from the SPI device.
* Erratum Workaround:
* Work in one of the following configurations:
* 1. Set CPOL=CPHA=0 in "SPI Interface Configuration
* Register".
* 2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1
* Register" before setting the interface.
*/
reg = readl(spi_reg(orion_spi, ORION_SPI_TIMING_PARAMS_REG));
reg &= ~ORION_SPI_TMISO_SAMPLE_MASK;
if (clk_get_rate(orion_spi->clk) == 250000000 &&
speed == 50000000 && spi->mode & SPI_CPOL &&
spi->mode & SPI_CPHA)
reg |= ORION_SPI_TMISO_SAMPLE_2;
else
reg |= ORION_SPI_TMISO_SAMPLE_1; /* This is the default value */
writel(reg, spi_reg(orion_spi, ORION_SPI_TIMING_PARAMS_REG));
}
/*
* called only when no transfer is active on the bus
*/
static int
orion_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
{
struct orion_spi *orion_spi;
unsigned int speed = spi->max_speed_hz;
unsigned int bits_per_word = spi->bits_per_word;
int rc;
orion_spi = spi_master_get_devdata(spi->master);
if ((t != NULL) && t->speed_hz)
speed = t->speed_hz;
if ((t != NULL) && t->bits_per_word)
bits_per_word = t->bits_per_word;
orion_spi_mode_set(spi);
if (orion_spi->devdata->is_errata_50mhz_ac)
orion_spi_50mhz_ac_timing_erratum(spi, speed);
rc = orion_spi_baudrate_set(spi, speed);
if (rc)
return rc;
if (bits_per_word == 16)
orion_spi_setbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
ORION_SPI_IF_8_16_BIT_MODE);
else
orion_spi_clrbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
ORION_SPI_IF_8_16_BIT_MODE);
return 0;
}
static void orion_spi_set_cs(struct spi_device *spi, bool enable)
{
struct orion_spi *orion_spi;
int cs;
orion_spi = spi_master_get_devdata(spi->master);
if (gpio_is_valid(spi->cs_gpio))
cs = orion_spi->unused_hw_gpio;
else
cs = spi->chip_select;
orion_spi_clrbits(orion_spi, ORION_SPI_IF_CTRL_REG, ORION_SPI_CS_MASK);
orion_spi_setbits(orion_spi, ORION_SPI_IF_CTRL_REG,
ORION_SPI_CS(cs));
/* Chip select logic is inverted from spi_set_cs */
if (!enable)
orion_spi_setbits(orion_spi, ORION_SPI_IF_CTRL_REG, 0x1);
else
orion_spi_clrbits(orion_spi, ORION_SPI_IF_CTRL_REG, 0x1);
}
static inline int orion_spi_wait_till_ready(struct orion_spi *orion_spi)
{
int i;
for (i = 0; i < ORION_SPI_WAIT_RDY_MAX_LOOP; i++) {
if (readl(spi_reg(orion_spi, ORION_SPI_INT_CAUSE_REG)))
return 1;
udelay(1);
}
return -1;
}
static inline int
orion_spi_write_read_8bit(struct spi_device *spi,
const u8 **tx_buf, u8 **rx_buf)
{
void __iomem *tx_reg, *rx_reg, *int_reg;
struct orion_spi *orion_spi;
orion_spi = spi_master_get_devdata(spi->master);
tx_reg = spi_reg(orion_spi, ORION_SPI_DATA_OUT_REG);
rx_reg = spi_reg(orion_spi, ORION_SPI_DATA_IN_REG);
int_reg = spi_reg(orion_spi, ORION_SPI_INT_CAUSE_REG);
/* clear the interrupt cause register */
writel(0x0, int_reg);
if (tx_buf && *tx_buf)
writel(*(*tx_buf)++, tx_reg);
else
writel(0, tx_reg);
if (orion_spi_wait_till_ready(orion_spi) < 0) {
dev_err(&spi->dev, "TXS timed out\n");
return -1;
}
if (rx_buf && *rx_buf)
*(*rx_buf)++ = readl(rx_reg);
return 1;
}
static inline int
orion_spi_write_read_16bit(struct spi_device *spi,
const u16 **tx_buf, u16 **rx_buf)
{
void __iomem *tx_reg, *rx_reg, *int_reg;
struct orion_spi *orion_spi;
orion_spi = spi_master_get_devdata(spi->master);
tx_reg = spi_reg(orion_spi, ORION_SPI_DATA_OUT_REG);
rx_reg = spi_reg(orion_spi, ORION_SPI_DATA_IN_REG);
int_reg = spi_reg(orion_spi, ORION_SPI_INT_CAUSE_REG);
/* clear the interrupt cause register */
writel(0x0, int_reg);
if (tx_buf && *tx_buf)
writel(__cpu_to_le16(get_unaligned((*tx_buf)++)), tx_reg);
else
writel(0, tx_reg);
if (orion_spi_wait_till_ready(orion_spi) < 0) {
dev_err(&spi->dev, "TXS timed out\n");
return -1;
}
if (rx_buf && *rx_buf)
put_unaligned(__le16_to_cpu(readl(rx_reg)), (*rx_buf)++);
return 1;
}
static unsigned int
orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
{
unsigned int count;
int word_len;
struct orion_spi *orion_spi;
int cs = spi->chip_select;
word_len = spi->bits_per_word;
count = xfer->len;
orion_spi = spi_master_get_devdata(spi->master);
/*
* Use SPI direct write mode if base address is available. Otherwise
* fall back to PIO mode for this transfer.
*/
if ((orion_spi->child[cs].direct_access.vaddr) && (xfer->tx_buf) &&
(word_len == 8)) {
unsigned int cnt = count / 4;
unsigned int rem = count % 4;
/*
* Send the TX-data to the SPI device via the direct
* mapped address window
*/
iowrite32_rep(orion_spi->child[cs].direct_access.vaddr,
xfer->tx_buf, cnt);
if (rem) {
u32 *buf = (u32 *)xfer->tx_buf;
iowrite8_rep(orion_spi->child[cs].direct_access.vaddr,
&buf[cnt], rem);
}
return count;
}
if (word_len == 8) {
const u8 *tx = xfer->tx_buf;
u8 *rx = xfer->rx_buf;
do {
if (orion_spi_write_read_8bit(spi, &tx, &rx) < 0)
goto out;
count--;
} while (count);
} else if (word_len == 16) {
const u16 *tx = xfer->tx_buf;
u16 *rx = xfer->rx_buf;
do {
if (orion_spi_write_read_16bit(spi, &tx, &rx) < 0)
goto out;
count -= 2;
} while (count);
}
out:
return xfer->len - count;
}
static int orion_spi_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *t)
{
int status = 0;
status = orion_spi_setup_transfer(spi, t);
if (status < 0)
return status;
if (t->len)
orion_spi_write_read(spi, t);
return status;
}
static int orion_spi_setup(struct spi_device *spi)
{
if (gpio_is_valid(spi->cs_gpio)) {
gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
}
return orion_spi_setup_transfer(spi, NULL);
}
static int orion_spi_reset(struct orion_spi *orion_spi)
{
/* Verify that the CS is deasserted */
orion_spi_clrbits(orion_spi, ORION_SPI_IF_CTRL_REG, 0x1);
/* Don't deassert CS between the direct mapped SPI transfers */
writel(0, spi_reg(orion_spi, SPI_DIRECT_WRITE_CONFIG_REG));
return 0;
}
static const struct orion_spi_dev orion_spi_dev_data = {
.typ = ORION_SPI,
.min_divisor = 4,
.max_divisor = 30,
.prescale_mask = ORION_SPI_CLK_PRESCALE_MASK,
};
static const struct orion_spi_dev armada_370_spi_dev_data = {
.typ = ARMADA_SPI,
.min_divisor = 4,
.max_divisor = 1920,
.max_hz = 50000000,
.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
};
static const struct orion_spi_dev armada_xp_spi_dev_data = {
.typ = ARMADA_SPI,
.max_hz = 50000000,
.max_divisor = 1920,
.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
};
static const struct orion_spi_dev armada_375_spi_dev_data = {
.typ = ARMADA_SPI,
.min_divisor = 15,
.max_divisor = 1920,
.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
};
static const struct orion_spi_dev armada_380_spi_dev_data = {
.typ = ARMADA_SPI,
.max_hz = 50000000,
.max_divisor = 1920,
.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
.is_errata_50mhz_ac = true,
};
static const struct of_device_id orion_spi_of_match_table[] = {
{
.compatible = "marvell,orion-spi",
.data = &orion_spi_dev_data,
},
{
.compatible = "marvell,armada-370-spi",
.data = &armada_370_spi_dev_data,
},
{
.compatible = "marvell,armada-375-spi",
.data = &armada_375_spi_dev_data,
},
{
.compatible = "marvell,armada-380-spi",
.data = &armada_380_spi_dev_data,
},
{
.compatible = "marvell,armada-390-spi",
.data = &armada_xp_spi_dev_data,
},
{
.compatible = "marvell,armada-xp-spi",
.data = &armada_xp_spi_dev_data,
},
{}
};
MODULE_DEVICE_TABLE(of, orion_spi_of_match_table);
static int orion_spi_probe(struct platform_device *pdev)
{
const struct of_device_id *of_id;
const struct orion_spi_dev *devdata;
struct spi_master *master;
struct orion_spi *spi;
struct resource *r;
unsigned long tclk_hz;
int status = 0;
struct device_node *np;
master = spi_alloc_master(&pdev->dev, sizeof(*spi));
if (master == NULL) {
dev_dbg(&pdev->dev, "master allocation failed\n");
return -ENOMEM;
}
if (pdev->id != -1)
master->bus_num = pdev->id;
if (pdev->dev.of_node) {
u32 cell_index;
if (!of_property_read_u32(pdev->dev.of_node, "cell-index",
&cell_index))
master->bus_num = cell_index;
}
/* we support all 4 SPI modes and LSB first option */
master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_LSB_FIRST;
master->set_cs = orion_spi_set_cs;
master->transfer_one = orion_spi_transfer_one;
master->num_chipselect = ORION_NUM_CHIPSELECTS;
master->setup = orion_spi_setup;
master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
master->auto_runtime_pm = true;
master->flags = SPI_MASTER_GPIO_SS;
platform_set_drvdata(pdev, master);
spi = spi_master_get_devdata(master);
spi->master = master;
spi->unused_hw_gpio = -1;
of_id = of_match_device(orion_spi_of_match_table, &pdev->dev);
devdata = (of_id) ? of_id->data : &orion_spi_dev_data;
spi->devdata = devdata;
spi->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(spi->clk)) {
status = PTR_ERR(spi->clk);
goto out;
}
status = clk_prepare_enable(spi->clk);
if (status)
goto out;
/* The following clock is only used by some SoCs */
spi->axi_clk = devm_clk_get(&pdev->dev, "axi");
if (IS_ERR(spi->axi_clk) &&
PTR_ERR(spi->axi_clk) == -EPROBE_DEFER) {
status = -EPROBE_DEFER;
goto out_rel_clk;
}
if (!IS_ERR(spi->axi_clk))
clk_prepare_enable(spi->axi_clk);
tclk_hz = clk_get_rate(spi->clk);
/*
* With old device tree, armada-370-spi could be used with
* Armada XP, however for this SoC the maximum frequency is
* 50MHz instead of tclk/4. On Armada 370, tclk cannot be
* higher than 200MHz. So, in order to be able to handle both
* SoCs, we can take the minimum of 50MHz and tclk/4.
*/
if (of_device_is_compatible(pdev->dev.of_node,
"marvell,armada-370-spi"))
master->max_speed_hz = min(devdata->max_hz,
DIV_ROUND_UP(tclk_hz, devdata->min_divisor));
else if (devdata->min_divisor)
master->max_speed_hz =
DIV_ROUND_UP(tclk_hz, devdata->min_divisor);
else
master->max_speed_hz = devdata->max_hz;
master->min_speed_hz = DIV_ROUND_UP(tclk_hz, devdata->max_divisor);
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
spi->base = devm_ioremap_resource(&pdev->dev, r);
if (IS_ERR(spi->base)) {
status = PTR_ERR(spi->base);
goto out_rel_axi_clk;
}
for_each_available_child_of_node(pdev->dev.of_node, np) {
u32 cs;
int cs_gpio;
/* Get chip-select number from the "reg" property */
status = of_property_read_u32(np, "reg", &cs);
if (status) {
dev_err(&pdev->dev,
"%pOF has no valid 'reg' property (%d)\n",
np, status);
continue;
}
/*
* Initialize the CS GPIO:
* - properly request the actual GPIO signal
* - de-assert the logical signal so that all GPIO CS lines
* are inactive when probing for slaves
* - find an unused physical CS which will be driven for any
* slave which uses a CS GPIO
*/
cs_gpio = of_get_named_gpio(pdev->dev.of_node, "cs-gpios", cs);
if (cs_gpio > 0) {
char *gpio_name;
int cs_flags;
if (spi->unused_hw_gpio == -1) {
dev_info(&pdev->dev,
"Selected unused HW CS#%d for any GPIO CSes\n",
cs);
spi->unused_hw_gpio = cs;
}
gpio_name = devm_kasprintf(&pdev->dev, GFP_KERNEL,
"%s-CS%d", dev_name(&pdev->dev), cs);
if (!gpio_name) {
status = -ENOMEM;
goto out_rel_axi_clk;
}
cs_flags = of_property_read_bool(np, "spi-cs-high") ?
GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH;
status = devm_gpio_request_one(&pdev->dev, cs_gpio,
cs_flags, gpio_name);
if (status) {
dev_err(&pdev->dev,
"Can't request GPIO for CS %d\n", cs);
goto out_rel_axi_clk;
}
}
/*
* Check if an address is configured for this SPI device. If
* not, the MBus mapping via the 'ranges' property in the 'soc'
* node is not configured and this device should not use the
* direct mode. In this case, just continue with the next
* device.
*/
status = of_address_to_resource(pdev->dev.of_node, cs + 1, r);
if (status)
continue;
/*
* Only map one page for direct access. This is enough for the
* simple TX transfer which only writes to the first word.
* This needs to get extended for the direct SPI-NOR / SPI-NAND
* support, once this gets implemented.
*/
spi->child[cs].direct_access.vaddr = devm_ioremap(&pdev->dev,
r->start,
PAGE_SIZE);
if (!spi->child[cs].direct_access.vaddr) {
status = -ENOMEM;
goto out_rel_axi_clk;
}
spi->child[cs].direct_access.size = PAGE_SIZE;
dev_info(&pdev->dev, "CS%d configured for direct access\n", cs);
}
pm_runtime_set_active(&pdev->dev);
pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
pm_runtime_enable(&pdev->dev);
status = orion_spi_reset(spi);
if (status < 0)
goto out_rel_pm;
pm_runtime_mark_last_busy(&pdev->dev);
pm_runtime_put_autosuspend(&pdev->dev);
master->dev.of_node = pdev->dev.of_node;
status = spi_register_master(master);
if (status < 0)
goto out_rel_pm;
return status;
out_rel_pm:
pm_runtime_disable(&pdev->dev);
out_rel_axi_clk:
clk_disable_unprepare(spi->axi_clk);
out_rel_clk:
clk_disable_unprepare(spi->clk);
out:
spi_master_put(master);
return status;
}
static int orion_spi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct orion_spi *spi = spi_master_get_devdata(master);
pm_runtime_get_sync(&pdev->dev);
clk_disable_unprepare(spi->axi_clk);
clk_disable_unprepare(spi->clk);
spi_unregister_master(master);
pm_runtime_disable(&pdev->dev);
return 0;
}
MODULE_ALIAS("platform:" DRIVER_NAME);
#ifdef CONFIG_PM
static int orion_spi_runtime_suspend(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct orion_spi *spi = spi_master_get_devdata(master);
clk_disable_unprepare(spi->axi_clk);
clk_disable_unprepare(spi->clk);
return 0;
}
static int orion_spi_runtime_resume(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct orion_spi *spi = spi_master_get_devdata(master);
if (!IS_ERR(spi->axi_clk))
clk_prepare_enable(spi->axi_clk);
return clk_prepare_enable(spi->clk);
}
#endif
static const struct dev_pm_ops orion_spi_pm_ops = {
SET_RUNTIME_PM_OPS(orion_spi_runtime_suspend,
orion_spi_runtime_resume,
NULL)
};
static struct platform_driver orion_spi_driver = {
.driver = {
.name = DRIVER_NAME,
.pm = &orion_spi_pm_ops,
.of_match_table = of_match_ptr(orion_spi_of_match_table),
},
.probe = orion_spi_probe,
.remove = orion_spi_remove,
};
module_platform_driver(orion_spi_driver);
MODULE_DESCRIPTION("Orion SPI driver");
MODULE_AUTHOR("Shadi Ammouri <shadi@marvell.com>");
MODULE_LICENSE("GPL");