Daniel Drake d63b282645 Bluetooth: btusb: match generic class code in interface descriptor ... btusb currently has a generic match on USB device descriptors: { USB_DEVICE_INFO(0xe0, 0x01, 0x01) }, However, http://www.usb.org/developers/defined_class states: Base Class E0h (Wireless Controller) This base class is defined for devices that are Wireless controllers. Values not shown in the table below are reserved. These class codes are to be used in Interface Descriptors, with the exception of the Bluetooth class code which can also be used in a Device Descriptor. Add a match on the interface descriptors accordingly. This fixes compatibility with the RTL8723AU device shown below. This device conforms to the USB Interface Association Descriptor specification, which requires the device to have class ef/02/01. The extra IAD descriptor then specifies that interfaces 0 and 1 belong to the same function/driver, which is true. Provided that the Bluetooth device class spec accepts use of the IAD, I imagine that technically, all btusb devices should be configured like this. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=0724 Rev= 2.00 S: Manufacturer=Realtek S: Product=802.11n WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=500us Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>		2015-07-30 13:42:26 +02:00
..
accessibility
acpi
amba
android
ata
atm
auxdisplay
base
bcma
block
bluetooth	Bluetooth: btusb: match generic class code in interface descriptor	2015-07-30 13:42:26 +02:00
bus
cdrom
char
clk
clocksource
connector
cpufreq
cpuidle
crypto
dca
devfreq
dio
dma
dma-buf
edac
eisa
extcon
firewire
firmware
fmc
gpio
gpu
hid
hsi
hv
hwmon
hwspinlock
hwtracing/coresight
i2c
ide
idle
iio
infiniband
input
iommu
ipack
irqchip
isdn
leds
lguest
macintosh
mailbox
mcb
md
media
memory
memstick
message
mfd
misc
mmc
mtd
net	net: ieee802154: Remove redundant spi driver bus initialization	2015-07-23 17:10:51 +02:00
nfc
ntb
nubus
nvdimm
of	of_mdio: add new DT property 'managed' to specify the PHY management type	2015-07-21 16:12:55 -07:00
oprofile
parisc
parport
pci
pcmcia
phy
pinctrl	Pin control fixes for the v4.2 series:	2015-07-21 15:27:27 -07:00
platform
pnp
power
powercap
pps
ps3
ptp
pwm
rapidio
ras
regulator
remoteproc
reset
rpmsg
rtc
s390
sbus
scsi
sfi
sh
sn
soc
spi
spmi
ssb
staging
target
tc
thermal
thunderbolt
tty
uio
usb
uwb
vfio
vhost
video
virt
virtio
vlynq
vme
w1
watchdog
xen
zorro
Kconfig
Makefile