linux/include/linux/cyclades.h
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

828 lines
26 KiB
C

/* $Revision: 3.0 $$Date: 1998/11/02 14:20:59 $
* linux/include/linux/cyclades.h
*
* This file was initially written by
* Randolph Bentson <bentson@grieg.seaslug.org> and is maintained by
* Ivan Passos <ivan@cyclades.com>.
*
* This file contains the general definitions for the cyclades.c driver
*$Log: cyclades.h,v $
*Revision 3.1 2002/01/29 11:36:16 henrique
*added throttle field on struct cyclades_port to indicate whether the
*port is throttled or not
*
*Revision 3.1 2000/04/19 18:52:52 ivan
*converted address fields to unsigned long and added fields for physical
*addresses on cyclades_card structure;
*
*Revision 3.0 1998/11/02 14:20:59 ivan
*added nports field on cyclades_card structure;
*
*Revision 2.5 1998/08/03 16:57:01 ivan
*added cyclades_idle_stats structure;
*
*Revision 2.4 1998/06/01 12:09:53 ivan
*removed closing_wait2 from cyclades_port structure;
*
*Revision 2.3 1998/03/16 18:01:12 ivan
*changes in the cyclades_port structure to get it closer to the
*standard serial port structure;
*added constants for new ioctls;
*
*Revision 2.2 1998/02/17 16:50:00 ivan
*changes in the cyclades_port structure (addition of shutdown_wait and
*chip_rev variables);
*added constants for new ioctls and for CD1400 rev. numbers.
*
*Revision 2.1 1997/10/24 16:03:00 ivan
*added rflow (which allows enabling the CD1400 special flow control
*feature) and rtsdtr_inv (which allows DTR/RTS pin inversion) to
*cyclades_port structure;
*added Alpha support
*
*Revision 2.0 1997/06/30 10:30:00 ivan
*added some new doorbell command constants related to IOCTLW and
*UART error signaling
*
*Revision 1.8 1997/06/03 15:30:00 ivan
*added constant ZFIRM_HLT
*added constant CyPCI_Ze_win ( = 2 * Cy_PCI_Zwin)
*
*Revision 1.7 1997/03/26 10:30:00 daniel
*new entries at the end of cyclades_port struct to reallocate
*variables illegally allocated within card memory.
*
*Revision 1.6 1996/09/09 18:35:30 bentson
*fold in changes for Cyclom-Z -- including structures for
*communicating with board as well modest changes to original
*structures to support new features.
*
*Revision 1.5 1995/11/13 21:13:31 bentson
*changes suggested by Michael Chastain <mec@duracef.shout.net>
*to support use of this file in non-kernel applications
*
*
*/
#ifndef _LINUX_CYCLADES_H
#define _LINUX_CYCLADES_H
struct cyclades_monitor {
unsigned long int_count;
unsigned long char_count;
unsigned long char_max;
unsigned long char_last;
};
/*
* These stats all reflect activity since the device was last initialized.
* (i.e., since the port was opened with no other processes already having it
* open)
*/
struct cyclades_idle_stats {
time_t in_use; /* Time device has been in use (secs) */
time_t recv_idle; /* Time since last char received (secs) */
time_t xmit_idle; /* Time since last char transmitted (secs) */
unsigned long recv_bytes; /* Bytes received */
unsigned long xmit_bytes; /* Bytes transmitted */
unsigned long overruns; /* Input overruns */
unsigned long frame_errs; /* Input framing errors */
unsigned long parity_errs; /* Input parity errors */
};
#define CYCLADES_MAGIC 0x4359
#define CYGETMON 0x435901
#define CYGETTHRESH 0x435902
#define CYSETTHRESH 0x435903
#define CYGETDEFTHRESH 0x435904
#define CYSETDEFTHRESH 0x435905
#define CYGETTIMEOUT 0x435906
#define CYSETTIMEOUT 0x435907
#define CYGETDEFTIMEOUT 0x435908
#define CYSETDEFTIMEOUT 0x435909
#define CYSETRFLOW 0x43590a
#define CYGETRFLOW 0x43590b
#define CYSETRTSDTR_INV 0x43590c
#define CYGETRTSDTR_INV 0x43590d
#define CYZSETPOLLCYCLE 0x43590e
#define CYZGETPOLLCYCLE 0x43590f
#define CYGETCD1400VER 0x435910
#define CYGETCARDINFO 0x435911
#define CYSETWAIT 0x435912
#define CYGETWAIT 0x435913
/*************** CYCLOM-Z ADDITIONS ***************/
#define CZIOC ('M' << 8)
#define CZ_NBOARDS (CZIOC|0xfa)
#define CZ_BOOT_START (CZIOC|0xfb)
#define CZ_BOOT_DATA (CZIOC|0xfc)
#define CZ_BOOT_END (CZIOC|0xfd)
#define CZ_TEST (CZIOC|0xfe)
#define CZ_DEF_POLL (HZ/25)
#define MAX_BOARD 4 /* Max number of boards */
#define MAX_DEV 256 /* Max number of ports total */
#define CYZ_MAX_SPEED 921600
#define CYZ_FIFO_SIZE 16
#define CYZ_BOOT_NWORDS 0x100
struct CYZ_BOOT_CTRL {
unsigned short nboard;
int status[MAX_BOARD];
int nchannel[MAX_BOARD];
int fw_rev[MAX_BOARD];
unsigned long offset;
unsigned long data[CYZ_BOOT_NWORDS];
};
#ifndef DP_WINDOW_SIZE
/* #include "cyclomz.h" */
/****************** ****************** *******************/
/*
* The data types defined below are used in all ZFIRM interface
* data structures. They accomodate differences between HW
* architectures and compilers.
*/
#if defined(__alpha__)
typedef unsigned long ucdouble; /* 64 bits, unsigned */
typedef unsigned int uclong; /* 32 bits, unsigned */
#else
typedef unsigned long uclong; /* 32 bits, unsigned */
#endif
typedef unsigned short ucshort; /* 16 bits, unsigned */
typedef unsigned char ucchar; /* 8 bits, unsigned */
/*
* Memory Window Sizes
*/
#define DP_WINDOW_SIZE (0x00080000) /* window size 512 Kb */
#define ZE_DP_WINDOW_SIZE (0x00100000) /* window size 1 Mb (Ze and
8Zo V.2 */
#define CTRL_WINDOW_SIZE (0x00000080) /* runtime regs 128 bytes */
/*
* CUSTOM_REG - Cyclom-Z/PCI Custom Registers Set. The driver
* normally will access only interested on the fpga_id, fpga_version,
* start_cpu and stop_cpu.
*/
struct CUSTOM_REG {
uclong fpga_id; /* FPGA Identification Register */
uclong fpga_version; /* FPGA Version Number Register */
uclong cpu_start; /* CPU start Register (write) */
uclong cpu_stop; /* CPU stop Register (write) */
uclong misc_reg; /* Miscelaneous Register */
uclong idt_mode; /* IDT mode Register */
uclong uart_irq_status; /* UART IRQ status Register */
uclong clear_timer0_irq; /* Clear timer interrupt Register */
uclong clear_timer1_irq; /* Clear timer interrupt Register */
uclong clear_timer2_irq; /* Clear timer interrupt Register */
uclong test_register; /* Test Register */
uclong test_count; /* Test Count Register */
uclong timer_select; /* Timer select register */
uclong pr_uart_irq_status; /* Prioritized UART IRQ stat Reg */
uclong ram_wait_state; /* RAM wait-state Register */
uclong uart_wait_state; /* UART wait-state Register */
uclong timer_wait_state; /* timer wait-state Register */
uclong ack_wait_state; /* ACK wait State Register */
};
/*
* RUNTIME_9060 - PLX PCI9060ES local configuration and shared runtime
* registers. This structure can be used to access the 9060 registers
* (memory mapped).
*/
struct RUNTIME_9060 {
uclong loc_addr_range; /* 00h - Local Address Range */
uclong loc_addr_base; /* 04h - Local Address Base */
uclong loc_arbitr; /* 08h - Local Arbitration */
uclong endian_descr; /* 0Ch - Big/Little Endian Descriptor */
uclong loc_rom_range; /* 10h - Local ROM Range */
uclong loc_rom_base; /* 14h - Local ROM Base */
uclong loc_bus_descr; /* 18h - Local Bus descriptor */
uclong loc_range_mst; /* 1Ch - Local Range for Master to PCI */
uclong loc_base_mst; /* 20h - Local Base for Master PCI */
uclong loc_range_io; /* 24h - Local Range for Master IO */
uclong pci_base_mst; /* 28h - PCI Base for Master PCI */
uclong pci_conf_io; /* 2Ch - PCI configuration for Master IO */
uclong filler1; /* 30h */
uclong filler2; /* 34h */
uclong filler3; /* 38h */
uclong filler4; /* 3Ch */
uclong mail_box_0; /* 40h - Mail Box 0 */
uclong mail_box_1; /* 44h - Mail Box 1 */
uclong mail_box_2; /* 48h - Mail Box 2 */
uclong mail_box_3; /* 4Ch - Mail Box 3 */
uclong filler5; /* 50h */
uclong filler6; /* 54h */
uclong filler7; /* 58h */
uclong filler8; /* 5Ch */
uclong pci_doorbell; /* 60h - PCI to Local Doorbell */
uclong loc_doorbell; /* 64h - Local to PCI Doorbell */
uclong intr_ctrl_stat; /* 68h - Interrupt Control/Status */
uclong init_ctrl; /* 6Ch - EEPROM control, Init Control, etc */
};
/* Values for the Local Base Address re-map register */
#define WIN_RAM 0x00000001L /* set the sliding window to RAM */
#define WIN_CREG 0x14000001L /* set the window to custom Registers */
/* Values timer select registers */
#define TIMER_BY_1M 0x00 /* clock divided by 1M */
#define TIMER_BY_256K 0x01 /* clock divided by 256k */
#define TIMER_BY_128K 0x02 /* clock divided by 128k */
#define TIMER_BY_32K 0x03 /* clock divided by 32k */
/****************** ****************** *******************/
#endif
#ifndef ZFIRM_ID
/* #include "zfwint.h" */
/****************** ****************** *******************/
/*
* This file contains the definitions for interfacing with the
* Cyclom-Z ZFIRM Firmware.
*/
/* General Constant definitions */
#define MAX_CHAN 64 /* max number of channels per board */
/* firmware id structure (set after boot) */
#define ID_ADDRESS 0x00000180L /* signature/pointer address */
#define ZFIRM_ID 0x5557465AL /* ZFIRM/U signature */
#define ZFIRM_HLT 0x59505B5CL /* ZFIRM needs external power supply */
#define ZFIRM_RST 0x56040674L /* RST signal (due to FW reset) */
#define ZF_TINACT_DEF 1000 /* default inactivity timeout
(1000 ms) */
#define ZF_TINACT ZF_TINACT_DEF
struct FIRM_ID {
uclong signature; /* ZFIRM/U signature */
uclong zfwctrl_addr; /* pointer to ZFW_CTRL structure */
};
/* Op. System id */
#define C_OS_LINUX 0x00000030 /* generic Linux system */
/* channel op_mode */
#define C_CH_DISABLE 0x00000000 /* channel is disabled */
#define C_CH_TXENABLE 0x00000001 /* channel Tx enabled */
#define C_CH_RXENABLE 0x00000002 /* channel Rx enabled */
#define C_CH_ENABLE 0x00000003 /* channel Tx/Rx enabled */
#define C_CH_LOOPBACK 0x00000004 /* Loopback mode */
/* comm_parity - parity */
#define C_PR_NONE 0x00000000 /* None */
#define C_PR_ODD 0x00000001 /* Odd */
#define C_PR_EVEN 0x00000002 /* Even */
#define C_PR_MARK 0x00000004 /* Mark */
#define C_PR_SPACE 0x00000008 /* Space */
#define C_PR_PARITY 0x000000ff
#define C_PR_DISCARD 0x00000100 /* discard char with frame/par error */
#define C_PR_IGNORE 0x00000200 /* ignore frame/par error */
/* comm_data_l - data length and stop bits */
#define C_DL_CS5 0x00000001
#define C_DL_CS6 0x00000002
#define C_DL_CS7 0x00000004
#define C_DL_CS8 0x00000008
#define C_DL_CS 0x0000000f
#define C_DL_1STOP 0x00000010
#define C_DL_15STOP 0x00000020
#define C_DL_2STOP 0x00000040
#define C_DL_STOP 0x000000f0
/* interrupt enabling/status */
#define C_IN_DISABLE 0x00000000 /* zero, disable interrupts */
#define C_IN_TXBEMPTY 0x00000001 /* tx buffer empty */
#define C_IN_TXLOWWM 0x00000002 /* tx buffer below LWM */
#define C_IN_RXHIWM 0x00000010 /* rx buffer above HWM */
#define C_IN_RXNNDT 0x00000020 /* rx no new data timeout */
#define C_IN_MDCD 0x00000100 /* modem DCD change */
#define C_IN_MDSR 0x00000200 /* modem DSR change */
#define C_IN_MRI 0x00000400 /* modem RI change */
#define C_IN_MCTS 0x00000800 /* modem CTS change */
#define C_IN_RXBRK 0x00001000 /* Break received */
#define C_IN_PR_ERROR 0x00002000 /* parity error */
#define C_IN_FR_ERROR 0x00004000 /* frame error */
#define C_IN_OVR_ERROR 0x00008000 /* overrun error */
#define C_IN_RXOFL 0x00010000 /* RX buffer overflow */
#define C_IN_IOCTLW 0x00020000 /* I/O control w/ wait */
#define C_IN_MRTS 0x00040000 /* modem RTS drop */
#define C_IN_ICHAR 0x00080000
/* flow control */
#define C_FL_OXX 0x00000001 /* output Xon/Xoff flow control */
#define C_FL_IXX 0x00000002 /* output Xon/Xoff flow control */
#define C_FL_OIXANY 0x00000004 /* output Xon/Xoff (any xon) */
#define C_FL_SWFLOW 0x0000000f
/* flow status */
#define C_FS_TXIDLE 0x00000000 /* no Tx data in the buffer or UART */
#define C_FS_SENDING 0x00000001 /* UART is sending data */
#define C_FS_SWFLOW 0x00000002 /* Tx is stopped by received Xoff */
/* rs_control/rs_status RS-232 signals */
#define C_RS_PARAM 0x80000000 /* Indicates presence of parameter in
IOCTLM command */
#define C_RS_RTS 0x00000001 /* RTS */
#define C_RS_DTR 0x00000004 /* DTR */
#define C_RS_DCD 0x00000100 /* CD */
#define C_RS_DSR 0x00000200 /* DSR */
#define C_RS_RI 0x00000400 /* RI */
#define C_RS_CTS 0x00000800 /* CTS */
/* commands Host <-> Board */
#define C_CM_RESET 0x01 /* reset/flush buffers */
#define C_CM_IOCTL 0x02 /* re-read CH_CTRL */
#define C_CM_IOCTLW 0x03 /* re-read CH_CTRL, intr when done */
#define C_CM_IOCTLM 0x04 /* RS-232 outputs change */
#define C_CM_SENDXOFF 0x10 /* send Xoff */
#define C_CM_SENDXON 0x11 /* send Xon */
#define C_CM_CLFLOW 0x12 /* Clear flow control (resume) */
#define C_CM_SENDBRK 0x41 /* send break */
#define C_CM_INTBACK 0x42 /* Interrupt back */
#define C_CM_SET_BREAK 0x43 /* Tx break on */
#define C_CM_CLR_BREAK 0x44 /* Tx break off */
#define C_CM_CMD_DONE 0x45 /* Previous command done */
#define C_CM_INTBACK2 0x46 /* Alternate Interrupt back */
#define C_CM_TINACT 0x51 /* set inactivity detection */
#define C_CM_IRQ_ENBL 0x52 /* enable generation of interrupts */
#define C_CM_IRQ_DSBL 0x53 /* disable generation of interrupts */
#define C_CM_ACK_ENBL 0x54 /* enable acknowledged interrupt mode */
#define C_CM_ACK_DSBL 0x55 /* disable acknowledged intr mode */
#define C_CM_FLUSH_RX 0x56 /* flushes Rx buffer */
#define C_CM_FLUSH_TX 0x57 /* flushes Tx buffer */
#define C_CM_Q_ENABLE 0x58 /* enables queue access from the
driver */
#define C_CM_Q_DISABLE 0x59 /* disables queue access from the
driver */
#define C_CM_TXBEMPTY 0x60 /* Tx buffer is empty */
#define C_CM_TXLOWWM 0x61 /* Tx buffer low water mark */
#define C_CM_RXHIWM 0x62 /* Rx buffer high water mark */
#define C_CM_RXNNDT 0x63 /* rx no new data timeout */
#define C_CM_TXFEMPTY 0x64
#define C_CM_ICHAR 0x65
#define C_CM_MDCD 0x70 /* modem DCD change */
#define C_CM_MDSR 0x71 /* modem DSR change */
#define C_CM_MRI 0x72 /* modem RI change */
#define C_CM_MCTS 0x73 /* modem CTS change */
#define C_CM_MRTS 0x74 /* modem RTS drop */
#define C_CM_RXBRK 0x84 /* Break received */
#define C_CM_PR_ERROR 0x85 /* Parity error */
#define C_CM_FR_ERROR 0x86 /* Frame error */
#define C_CM_OVR_ERROR 0x87 /* Overrun error */
#define C_CM_RXOFL 0x88 /* RX buffer overflow */
#define C_CM_CMDERROR 0x90 /* command error */
#define C_CM_FATAL 0x91 /* fatal error */
#define C_CM_HW_RESET 0x92 /* reset board */
/*
* CH_CTRL - This per port structure contains all parameters
* that control an specific port. It can be seen as the
* configuration registers of a "super-serial-controller".
*/
struct CH_CTRL {
uclong op_mode; /* operation mode */
uclong intr_enable; /* interrupt masking */
uclong sw_flow; /* SW flow control */
uclong flow_status; /* output flow status */
uclong comm_baud; /* baud rate - numerically specified */
uclong comm_parity; /* parity */
uclong comm_data_l; /* data length/stop */
uclong comm_flags; /* other flags */
uclong hw_flow; /* HW flow control */
uclong rs_control; /* RS-232 outputs */
uclong rs_status; /* RS-232 inputs */
uclong flow_xon; /* xon char */
uclong flow_xoff; /* xoff char */
uclong hw_overflow; /* hw overflow counter */
uclong sw_overflow; /* sw overflow counter */
uclong comm_error; /* frame/parity error counter */
uclong ichar;
uclong filler[7];
};
/*
* BUF_CTRL - This per channel structure contains
* all Tx and Rx buffer control for a given channel.
*/
struct BUF_CTRL {
uclong flag_dma; /* buffers are in Host memory */
uclong tx_bufaddr; /* address of the tx buffer */
uclong tx_bufsize; /* tx buffer size */
uclong tx_threshold; /* tx low water mark */
uclong tx_get; /* tail index tx buf */
uclong tx_put; /* head index tx buf */
uclong rx_bufaddr; /* address of the rx buffer */
uclong rx_bufsize; /* rx buffer size */
uclong rx_threshold; /* rx high water mark */
uclong rx_get; /* tail index rx buf */
uclong rx_put; /* head index rx buf */
uclong filler[5]; /* filler to align structures */
};
/*
* BOARD_CTRL - This per board structure contains all global
* control fields related to the board.
*/
struct BOARD_CTRL {
/* static info provided by the on-board CPU */
uclong n_channel; /* number of channels */
uclong fw_version; /* firmware version */
/* static info provided by the driver */
uclong op_system; /* op_system id */
uclong dr_version; /* driver version */
/* board control area */
uclong inactivity; /* inactivity control */
/* host to FW commands */
uclong hcmd_channel; /* channel number */
uclong hcmd_param; /* pointer to parameters */
/* FW to Host commands */
uclong fwcmd_channel; /* channel number */
uclong fwcmd_param; /* pointer to parameters */
uclong zf_int_queue_addr; /* offset for INT_QUEUE structure */
/* filler so the structures are aligned */
uclong filler[6];
};
/* Host Interrupt Queue */
#define QUEUE_SIZE (10*MAX_CHAN)
struct INT_QUEUE {
unsigned char intr_code[QUEUE_SIZE];
unsigned long channel[QUEUE_SIZE];
unsigned long param[QUEUE_SIZE];
unsigned long put;
unsigned long get;
};
/*
* ZFW_CTRL - This is the data structure that includes all other
* data structures used by the Firmware.
*/
struct ZFW_CTRL {
struct BOARD_CTRL board_ctrl;
struct CH_CTRL ch_ctrl[MAX_CHAN];
struct BUF_CTRL buf_ctrl[MAX_CHAN];
};
/****************** ****************** *******************/
#endif
/* Per card data structure */
struct resource;
struct cyclades_card {
unsigned long base_phys;
unsigned long ctl_phys;
void __iomem *base_addr;
void __iomem *ctl_addr;
int irq;
int num_chips; /* 0 if card absent, -1 if Z/PCI, else Y */
int first_line; /* minor number of first channel on card */
int nports; /* Number of ports in the card */
int bus_index; /* address shift - 0 for ISA, 1 for PCI */
int intr_enabled; /* FW Interrupt flag - 0 disabled, 1 enabled */
struct pci_dev *pdev;
#ifdef __KERNEL__
spinlock_t card_lock;
#else
unsigned long filler;
#endif
};
struct cyclades_chip {
int filler;
};
#ifdef __KERNEL__
/***************************************
* Memory access functions/macros *
* (required to support Alpha systems) *
***************************************/
#define cy_writeb(port,val) {writeb((val),(port)); mb();}
#define cy_writew(port,val) {writew((val),(port)); mb();}
#define cy_writel(port,val) {writel((val),(port)); mb();}
#define cy_readb(port) readb(port)
#define cy_readw(port) readw(port)
#define cy_readl(port) readl(port)
/*
* Statistics counters
*/
struct cyclades_icount {
__u32 cts, dsr, rng, dcd, tx, rx;
__u32 frame, parity, overrun, brk;
__u32 buf_overrun;
};
/*
* This is our internal structure for each serial port's state.
*
* Many fields are paralleled by the structure used by the serial_struct
* structure.
*
* For definitions of the flags field, see tty.h
*/
struct cyclades_port {
int magic;
int card;
int line;
int flags; /* defined in tty.h */
int type; /* UART type */
struct tty_struct *tty;
int read_status_mask;
int ignore_status_mask;
int timeout;
int xmit_fifo_size;
int cor1,cor2,cor3,cor4,cor5;
int tbpr,tco,rbpr,rco;
int baud;
int rflow;
int rtsdtr_inv;
int chip_rev;
int custom_divisor;
int x_char; /* to be pushed out ASAP */
int close_delay;
unsigned short closing_wait;
unsigned long event;
unsigned long last_active;
int count; /* # of fd on device */
int breakon;
int breakoff;
int blocked_open; /* # of blocked opens */
unsigned char *xmit_buf;
int xmit_head;
int xmit_tail;
int xmit_cnt;
int default_threshold;
int default_timeout;
unsigned long jiffies[3];
unsigned long rflush_count;
struct cyclades_monitor mon;
struct cyclades_idle_stats idle_stats;
struct cyclades_icount icount;
struct work_struct tqueue;
wait_queue_head_t open_wait;
wait_queue_head_t close_wait;
wait_queue_head_t shutdown_wait;
wait_queue_head_t delta_msr_wait;
int throttle;
};
/*
* Events are used to schedule things to happen at timer-interrupt
* time, instead of at cy interrupt time.
*/
#define Cy_EVENT_READ_PROCESS 0
#define Cy_EVENT_WRITE_WAKEUP 1
#define Cy_EVENT_HANGUP 2
#define Cy_EVENT_BREAK 3
#define Cy_EVENT_OPEN_WAKEUP 4
#define Cy_EVENT_SHUTDOWN_WAKEUP 5
#define Cy_EVENT_DELTA_WAKEUP 6
#define Cy_EVENT_Z_RX_FULL 7
#define CLOSING_WAIT_DELAY 30*HZ
#define CY_CLOSING_WAIT_NONE 65535
#define CY_CLOSING_WAIT_INF 0
#define CyMAX_CHIPS_PER_CARD 8
#define CyMAX_CHAR_FIFO 12
#define CyPORTS_PER_CHIP 4
#define CD1400_MAX_SPEED 115200
#define CyISA_Ywin 0x2000
#define CyPCI_Ywin 0x4000
#define CyPCI_Yctl 0x80
#define CyPCI_Zctl CTRL_WINDOW_SIZE
#define CyPCI_Zwin 0x80000
#define CyPCI_Ze_win (2 * CyPCI_Zwin)
#define PCI_DEVICE_ID_MASK 0x06
/**** CD1400 registers ****/
#define CD1400_REV_G 0x46
#define CD1400_REV_J 0x48
#define CyRegSize 0x0400
#define Cy_HwReset 0x1400
#define Cy_ClrIntr 0x1800
#define Cy_EpldRev 0x1e00
/* Global Registers */
#define CyGFRCR (0x40*2)
#define CyRevE (44)
#define CyCAR (0x68*2)
#define CyCHAN_0 (0x00)
#define CyCHAN_1 (0x01)
#define CyCHAN_2 (0x02)
#define CyCHAN_3 (0x03)
#define CyGCR (0x4B*2)
#define CyCH0_SERIAL (0x00)
#define CyCH0_PARALLEL (0x80)
#define CySVRR (0x67*2)
#define CySRModem (0x04)
#define CySRTransmit (0x02)
#define CySRReceive (0x01)
#define CyRICR (0x44*2)
#define CyTICR (0x45*2)
#define CyMICR (0x46*2)
#define CyICR0 (0x00)
#define CyICR1 (0x01)
#define CyICR2 (0x02)
#define CyICR3 (0x03)
#define CyRIR (0x6B*2)
#define CyTIR (0x6A*2)
#define CyMIR (0x69*2)
#define CyIRDirEq (0x80)
#define CyIRBusy (0x40)
#define CyIRUnfair (0x20)
#define CyIRContext (0x1C)
#define CyIRChannel (0x03)
#define CyPPR (0x7E*2)
#define CyCLOCK_20_1MS (0x27)
#define CyCLOCK_25_1MS (0x31)
#define CyCLOCK_25_5MS (0xf4)
#define CyCLOCK_60_1MS (0x75)
#define CyCLOCK_60_2MS (0xea)
/* Virtual Registers */
#define CyRIVR (0x43*2)
#define CyTIVR (0x42*2)
#define CyMIVR (0x41*2)
#define CyIVRMask (0x07)
#define CyIVRRxEx (0x07)
#define CyIVRRxOK (0x03)
#define CyIVRTxOK (0x02)
#define CyIVRMdmOK (0x01)
#define CyTDR (0x63*2)
#define CyRDSR (0x62*2)
#define CyTIMEOUT (0x80)
#define CySPECHAR (0x70)
#define CyBREAK (0x08)
#define CyPARITY (0x04)
#define CyFRAME (0x02)
#define CyOVERRUN (0x01)
#define CyMISR (0x4C*2)
/* see CyMCOR_ and CyMSVR_ for bits*/
#define CyEOSRR (0x60*2)
/* Channel Registers */
#define CyLIVR (0x18*2)
#define CyMscsr (0x01)
#define CyTdsr (0x02)
#define CyRgdsr (0x03)
#define CyRedsr (0x07)
#define CyCCR (0x05*2)
/* Format 1 */
#define CyCHAN_RESET (0x80)
#define CyCHIP_RESET (0x81)
#define CyFlushTransFIFO (0x82)
/* Format 2 */
#define CyCOR_CHANGE (0x40)
#define CyCOR1ch (0x02)
#define CyCOR2ch (0x04)
#define CyCOR3ch (0x08)
/* Format 3 */
#define CySEND_SPEC_1 (0x21)
#define CySEND_SPEC_2 (0x22)
#define CySEND_SPEC_3 (0x23)
#define CySEND_SPEC_4 (0x24)
/* Format 4 */
#define CyCHAN_CTL (0x10)
#define CyDIS_RCVR (0x01)
#define CyENB_RCVR (0x02)
#define CyDIS_XMTR (0x04)
#define CyENB_XMTR (0x08)
#define CySRER (0x06*2)
#define CyMdmCh (0x80)
#define CyRxData (0x10)
#define CyTxRdy (0x04)
#define CyTxMpty (0x02)
#define CyNNDT (0x01)
#define CyCOR1 (0x08*2)
#define CyPARITY_NONE (0x00)
#define CyPARITY_0 (0x20)
#define CyPARITY_1 (0xA0)
#define CyPARITY_E (0x40)
#define CyPARITY_O (0xC0)
#define Cy_1_STOP (0x00)
#define Cy_1_5_STOP (0x04)
#define Cy_2_STOP (0x08)
#define Cy_5_BITS (0x00)
#define Cy_6_BITS (0x01)
#define Cy_7_BITS (0x02)
#define Cy_8_BITS (0x03)
#define CyCOR2 (0x09*2)
#define CyIXM (0x80)
#define CyTxIBE (0x40)
#define CyETC (0x20)
#define CyAUTO_TXFL (0x60)
#define CyLLM (0x10)
#define CyRLM (0x08)
#define CyRtsAO (0x04)
#define CyCtsAE (0x02)
#define CyDsrAE (0x01)
#define CyCOR3 (0x0A*2)
#define CySPL_CH_DRANGE (0x80) /* special character detect range */
#define CySPL_CH_DET1 (0x40) /* enable special character detection
on SCHR4-SCHR3 */
#define CyFL_CTRL_TRNSP (0x20) /* Flow Control Transparency */
#define CySPL_CH_DET2 (0x10) /* Enable special character detection
on SCHR2-SCHR1 */
#define CyREC_FIFO (0x0F) /* Receive FIFO threshold */
#define CyCOR4 (0x1E*2)
#define CyCOR5 (0x1F*2)
#define CyCCSR (0x0B*2)
#define CyRxEN (0x80)
#define CyRxFloff (0x40)
#define CyRxFlon (0x20)
#define CyTxEN (0x08)
#define CyTxFloff (0x04)
#define CyTxFlon (0x02)
#define CyRDCR (0x0E*2)
#define CySCHR1 (0x1A*2)
#define CySCHR2 (0x1B*2)
#define CySCHR3 (0x1C*2)
#define CySCHR4 (0x1D*2)
#define CySCRL (0x22*2)
#define CySCRH (0x23*2)
#define CyLNC (0x24*2)
#define CyMCOR1 (0x15*2)
#define CyMCOR2 (0x16*2)
#define CyRTPR (0x21*2)
#define CyMSVR1 (0x6C*2)
#define CyMSVR2 (0x6D*2)
#define CyANY_DELTA (0xF0)
#define CyDSR (0x80)
#define CyCTS (0x40)
#define CyRI (0x20)
#define CyDCD (0x10)
#define CyDTR (0x02)
#define CyRTS (0x01)
#define CyPVSR (0x6F*2)
#define CyRBPR (0x78*2)
#define CyRCOR (0x7C*2)
#define CyTBPR (0x72*2)
#define CyTCOR (0x76*2)
/* Custom Registers */
#define CyPLX_VER (0x3400)
#define PLX_9050 0x0b
#define PLX_9060 0x0c
#define PLX_9080 0x0d
/***************************************************************************/
#endif /* __KERNEL__ */
#endif /* _LINUX_CYCLADES_H */