linux/Documentation/ABI
Kirill Smelkov cc62a7eb63 USB: EHCI: Allow users to override 80% max periodic bandwidth
There are cases, when 80% max isochronous bandwidth is too limiting.

For example I have two USB video capture cards which stream uncompressed
video, and to stream full NTSC + PAL videos we'd need

    NTSC 640x480 YUV422 @30fps      ~17.6 MB/s
    PAL  720x576 YUV422 @25fps      ~19.7 MB/s

isoc bandwidth.

Now, due to limited alt settings in capture devices NTSC one ends up
streaming with max_pkt_size=2688  and  PAL with max_pkt_size=2892, both
with interval=1. In terms of microframe time allocation this gives

    NTSC    ~53us
    PAL     ~57us

and together

    ~110us  >  100us == 80% of 125us uframe time.

So those two devices can't work together simultaneously because the'd
over allocate isochronous bandwidth.

80% seemed a bit arbitrary to me, and I've tried to raise it to 90% and
both devices started to work together, so I though sometimes it would be
a good idea for users to override hardcoded default of max 80% isoc
bandwidth.

After all, isn't it a user who should decide how to load the bus? If I
can live with 10% or even 5% bulk bandwidth that should be ok. I'm a USB
newcomer, but that 80% set in stone by USB 2.0 specification seems to be
chosen pretty arbitrary to me, just to serve as a reasonable default.

NOTE 1
~~~~~~

for two streams with max_pkt_size=3072 (worst case) both time
allocation would be 60us+60us=120us which is 96% periodic bandwidth
leaving 4% for bulk and control.  Alan Stern suggested that bulk then
would be problematic (less than 300*8 bittimes left per microframe), but
I think that is still enough for control traffic.

NOTE 2
~~~~~~

Sarah Sharp expressed concern that maxing out periodic bandwidth
could lead to vendor-specific hardware bugs on host controllers, because

> It's entirely possible that you'll run into
> vendor-specific bugs if you try to pack the schedule with isochronous
> transfers.  I don't think any hardware designer would seriously test or
> validate their hardware with a schedule that is basically a violation of
> the USB bus spec (more than 80% for periodic transfers).

So far I've only tested this patch on my HP Mini 5103 with N10 chipset

    kirr@mini:~$ lspci
    00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
    00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
    00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
    00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
    00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
    00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
    00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
    00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
    00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
    00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
    00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
    00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
    00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
    00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
    01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
    02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8059 PCI-E Gigabit Ethernet Controller (rev 11)

and the system works stable with 110us/uframe (~88%) isoc bandwith allocated for
above-mentioned isochronous transfers.

NOTE 3
~~~~~~

This feature is off by default. I mean max periodic bandwidth is set to
100us/uframe by default exactly as it was before the patch. So only those of us
who need the extreme settings are taking the risk - normal users who do not
alter uframe_periodic_max sysfs attribute should not see any change at all.

NOTE 4
~~~~~~

I've tried to update documentation in Documentation/ABI/ thoroughly, but
only "TBD" was put into Documentation/usb/ehci.txt -- the text there seems
to be outdated and much needing refreshing, before it could be amended.

Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-07-08 14:51:33 -07:00
..
obsolete ocfs2: remove the /sys/o2cb symlink 2011-05-23 23:37:14 -07:00
removed ocfs2: remove the /sys/o2cb symlink 2011-05-23 23:37:14 -07:00
stable backlight: add backlight type 2011-03-22 17:43:59 -07:00
testing USB: EHCI: Allow users to override 80% max periodic bandwidth 2011-07-08 14:51:33 -07:00
README [PATCH] Add kernel<->userspace ABI stability documentation 2006-06-21 12:40:47 -07:00

This directory attempts to document the ABI between the Linux kernel and
userspace, and the relative stability of these interfaces.  Due to the
everchanging nature of Linux, and the differing maturity levels, these
interfaces should be used by userspace programs in different ways.

We have four different levels of ABI stability, as shown by the four
different subdirectories in this location.  Interfaces may change levels
of stability according to the rules described below.

The different levels of stability are:

  stable/
	This directory documents the interfaces that the developer has
	defined to be stable.  Userspace programs are free to use these
	interfaces with no restrictions, and backward compatibility for
	them will be guaranteed for at least 2 years.  Most interfaces
	(like syscalls) are expected to never change and always be
	available.

  testing/
	This directory documents interfaces that are felt to be stable,
	as the main development of this interface has been completed.
	The interface can be changed to add new features, but the
	current interface will not break by doing this, unless grave
	errors or security problems are found in them.  Userspace
	programs can start to rely on these interfaces, but they must be
	aware of changes that can occur before these interfaces move to
	be marked stable.  Programs that use these interfaces are
	strongly encouraged to add their name to the description of
	these interfaces, so that the kernel developers can easily
	notify them if any changes occur (see the description of the
	layout of the files below for details on how to do this.)

  obsolete/
  	This directory documents interfaces that are still remaining in
	the kernel, but are marked to be removed at some later point in
	time.  The description of the interface will document the reason
	why it is obsolete and when it can be expected to be removed.
	The file Documentation/feature-removal-schedule.txt may describe
	some of these interfaces, giving a schedule for when they will
	be removed.

  removed/
	This directory contains a list of the old interfaces that have
	been removed from the kernel.

Every file in these directories will contain the following information:

What:		Short description of the interface
Date:		Date created
KernelVersion:	Kernel version this feature first showed up in.
Contact:	Primary contact for this interface (may be a mailing list)
Description:	Long description of the interface and how to use it.
Users:		All users of this interface who wish to be notified when
		it changes.  This is very important for interfaces in
		the "testing" stage, so that kernel developers can work
		with userspace developers to ensure that things do not
		break in ways that are unacceptable.  It is also
		important to get feedback for these interfaces to make
		sure they are working in a proper way and do not need to
		be changed further.


How things move between levels:

Interfaces in stable may move to obsolete, as long as the proper
notification is given.

Interfaces may be removed from obsolete and the kernel as long as the
documented amount of time has gone by.

Interfaces in the testing state can move to the stable state when the
developers feel they are finished.  They cannot be removed from the
kernel tree without going through the obsolete state first.

It's up to the developer to place their interfaces in the category they
wish for it to start out in.