linux/arch/arm/mach-omap2/board-zoom-debugboard.c
Sergio Aguirre fcbcea93ab omap3: zoom 2/3: Change debugboard serial port id
This is now changed to PLAT8250_DEV_PLATFORM (= 0), because
it's the only port that's going to be initialized in
Zoom 2/3 boards.

So, it doesn't make sense to keep the hardcoded 3 value anymore.

Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
2010-03-15 16:34:20 -05:00

164 lines
3.8 KiB
C

/*
* Copyright (C) 2009 Texas Instruments Inc.
* Mikkel Christensen <mlc@ti.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/gpio.h>
#include <linux/serial_8250.h>
#include <linux/smsc911x.h>
#include <linux/interrupt.h>
#include <plat/gpmc.h>
#define ZOOM_SMSC911X_CS 7
#define ZOOM_SMSC911X_GPIO 158
#define ZOOM_QUADUART_CS 3
#define ZOOM_QUADUART_GPIO 102
#define QUART_CLK 1843200
#define DEBUG_BASE 0x08000000
#define ZOOM_ETHR_START DEBUG_BASE
static struct resource zoom_smsc911x_resources[] = {
[0] = {
.start = ZOOM_ETHR_START,
.end = ZOOM_ETHR_START + SZ_4K,
.flags = IORESOURCE_MEM,
},
[1] = {
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
static struct smsc911x_platform_config zoom_smsc911x_config = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = SMSC911X_USE_32BIT,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct platform_device zoom_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(zoom_smsc911x_resources),
.resource = zoom_smsc911x_resources,
.dev = {
.platform_data = &zoom_smsc911x_config,
},
};
static inline void __init zoom_init_smsc911x(void)
{
int eth_cs;
unsigned long cs_mem_base;
int eth_gpio = 0;
eth_cs = ZOOM_SMSC911X_CS;
if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
return;
}
zoom_smsc911x_resources[0].start = cs_mem_base + 0x0;
zoom_smsc911x_resources[0].end = cs_mem_base + 0xff;
eth_gpio = ZOOM_SMSC911X_GPIO;
zoom_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
eth_gpio);
return;
}
gpio_direction_input(eth_gpio);
}
static struct plat_serial8250_port serial_platform_data[] = {
{
.mapbase = 0x10000000,
.irq = OMAP_GPIO_IRQ(102),
.flags = UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ,
.irqflags = IRQF_SHARED | IRQF_TRIGGER_RISING,
.iotype = UPIO_MEM,
.regshift = 1,
.uartclk = QUART_CLK,
}, {
.flags = 0
}
};
static struct platform_device zoom_debugboard_serial_device = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev = {
.platform_data = serial_platform_data,
},
};
static inline void __init zoom_init_quaduart(void)
{
int quart_cs;
unsigned long cs_mem_base;
int quart_gpio = 0;
quart_cs = ZOOM_QUADUART_CS;
if (gpmc_cs_request(quart_cs, SZ_1M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem"
"for Quad UART(TL16CP754C)\n");
return;
}
quart_gpio = ZOOM_QUADUART_GPIO;
if (gpio_request(quart_gpio, "TL16CP754C GPIO") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n",
quart_gpio);
return;
}
gpio_direction_input(quart_gpio);
}
static inline int omap_zoom_debugboard_detect(void)
{
int debug_board_detect = 0;
int ret = 1;
debug_board_detect = ZOOM_SMSC911X_GPIO;
if (gpio_request(debug_board_detect, "Zoom debug board detect") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for Zoom debug"
"board detect\n", debug_board_detect);
return 0;
}
gpio_direction_input(debug_board_detect);
if (!gpio_get_value(debug_board_detect)) {
ret = 0;
}
gpio_free(debug_board_detect);
return ret;
}
static struct platform_device *zoom_devices[] __initdata = {
&zoom_smsc911x_device,
&zoom_debugboard_serial_device,
};
int __init zoom_debugboard_init(void)
{
if (!omap_zoom_debugboard_detect())
return 0;
zoom_init_smsc911x();
zoom_init_quaduart();
return platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices));
}