linux/drivers/scsi/pm8001/pm8001_hwi.c
Mark Salyzyn 99c72ebceb [SCSI] pm8001: raise host can queue
This is a followup to a patch provided by Jack Wang on September 21 2011.

After increasing the CAN_QUEUE to 510 in pm8001 we discovered some performance
degredation from time to time. We needed to increase the MPI queue to
compensate and ensure we never hit that limit. We also needed to double
the margin to support event and administrivial commands that take from
the pool resulting in an occasional largely unproductive command completion
with soft error to the caller when the command pool is overloaded temporarily.

Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:02:07 +01:00

4716 lines
151 KiB
C

/*
* PMC-Sierra SPC 8001 SAS/SATA based host adapters driver
*
* Copyright (c) 2008-2009 USI Co., Ltd.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
*/
#include <linux/slab.h>
#include "pm8001_sas.h"
#include "pm8001_hwi.h"
#include "pm8001_chips.h"
#include "pm8001_ctl.h"
/**
* read_main_config_table - read the configure table and save it.
* @pm8001_ha: our hba card information
*/
static void __devinit read_main_config_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
pm8001_ha->main_cfg_tbl.signature = pm8001_mr32(address, 0x00);
pm8001_ha->main_cfg_tbl.interface_rev = pm8001_mr32(address, 0x04);
pm8001_ha->main_cfg_tbl.firmware_rev = pm8001_mr32(address, 0x08);
pm8001_ha->main_cfg_tbl.max_out_io = pm8001_mr32(address, 0x0C);
pm8001_ha->main_cfg_tbl.max_sgl = pm8001_mr32(address, 0x10);
pm8001_ha->main_cfg_tbl.ctrl_cap_flag = pm8001_mr32(address, 0x14);
pm8001_ha->main_cfg_tbl.gst_offset = pm8001_mr32(address, 0x18);
pm8001_ha->main_cfg_tbl.inbound_queue_offset =
pm8001_mr32(address, MAIN_IBQ_OFFSET);
pm8001_ha->main_cfg_tbl.outbound_queue_offset =
pm8001_mr32(address, MAIN_OBQ_OFFSET);
pm8001_ha->main_cfg_tbl.hda_mode_flag =
pm8001_mr32(address, MAIN_HDA_FLAGS_OFFSET);
/* read analog Setting offset from the configuration table */
pm8001_ha->main_cfg_tbl.anolog_setup_table_offset =
pm8001_mr32(address, MAIN_ANALOG_SETUP_OFFSET);
/* read Error Dump Offset and Length */
pm8001_ha->main_cfg_tbl.fatal_err_dump_offset0 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_OFFSET);
pm8001_ha->main_cfg_tbl.fatal_err_dump_length0 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_LENGTH);
pm8001_ha->main_cfg_tbl.fatal_err_dump_offset1 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_OFFSET);
pm8001_ha->main_cfg_tbl.fatal_err_dump_length1 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_LENGTH);
}
/**
* read_general_status_table - read the general status table and save it.
* @pm8001_ha: our hba card information
*/
static void __devinit
read_general_status_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->general_stat_tbl_addr;
pm8001_ha->gs_tbl.gst_len_mpistate = pm8001_mr32(address, 0x00);
pm8001_ha->gs_tbl.iq_freeze_state0 = pm8001_mr32(address, 0x04);
pm8001_ha->gs_tbl.iq_freeze_state1 = pm8001_mr32(address, 0x08);
pm8001_ha->gs_tbl.msgu_tcnt = pm8001_mr32(address, 0x0C);
pm8001_ha->gs_tbl.iop_tcnt = pm8001_mr32(address, 0x10);
pm8001_ha->gs_tbl.reserved = pm8001_mr32(address, 0x14);
pm8001_ha->gs_tbl.phy_state[0] = pm8001_mr32(address, 0x18);
pm8001_ha->gs_tbl.phy_state[1] = pm8001_mr32(address, 0x1C);
pm8001_ha->gs_tbl.phy_state[2] = pm8001_mr32(address, 0x20);
pm8001_ha->gs_tbl.phy_state[3] = pm8001_mr32(address, 0x24);
pm8001_ha->gs_tbl.phy_state[4] = pm8001_mr32(address, 0x28);
pm8001_ha->gs_tbl.phy_state[5] = pm8001_mr32(address, 0x2C);
pm8001_ha->gs_tbl.phy_state[6] = pm8001_mr32(address, 0x30);
pm8001_ha->gs_tbl.phy_state[7] = pm8001_mr32(address, 0x34);
pm8001_ha->gs_tbl.reserved1 = pm8001_mr32(address, 0x38);
pm8001_ha->gs_tbl.reserved2 = pm8001_mr32(address, 0x3C);
pm8001_ha->gs_tbl.reserved3 = pm8001_mr32(address, 0x40);
pm8001_ha->gs_tbl.recover_err_info[0] = pm8001_mr32(address, 0x44);
pm8001_ha->gs_tbl.recover_err_info[1] = pm8001_mr32(address, 0x48);
pm8001_ha->gs_tbl.recover_err_info[2] = pm8001_mr32(address, 0x4C);
pm8001_ha->gs_tbl.recover_err_info[3] = pm8001_mr32(address, 0x50);
pm8001_ha->gs_tbl.recover_err_info[4] = pm8001_mr32(address, 0x54);
pm8001_ha->gs_tbl.recover_err_info[5] = pm8001_mr32(address, 0x58);
pm8001_ha->gs_tbl.recover_err_info[6] = pm8001_mr32(address, 0x5C);
pm8001_ha->gs_tbl.recover_err_info[7] = pm8001_mr32(address, 0x60);
}
/**
* read_inbnd_queue_table - read the inbound queue table and save it.
* @pm8001_ha: our hba card information
*/
static void __devinit
read_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
{
int inbQ_num = 1;
int i;
void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
for (i = 0; i < inbQ_num; i++) {
u32 offset = i * 0x20;
pm8001_ha->inbnd_q_tbl[i].pi_pci_bar =
get_pci_bar_index(pm8001_mr32(address, (offset + 0x14)));
pm8001_ha->inbnd_q_tbl[i].pi_offset =
pm8001_mr32(address, (offset + 0x18));
}
}
/**
* read_outbnd_queue_table - read the outbound queue table and save it.
* @pm8001_ha: our hba card information
*/
static void __devinit
read_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
{
int outbQ_num = 1;
int i;
void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
for (i = 0; i < outbQ_num; i++) {
u32 offset = i * 0x24;
pm8001_ha->outbnd_q_tbl[i].ci_pci_bar =
get_pci_bar_index(pm8001_mr32(address, (offset + 0x14)));
pm8001_ha->outbnd_q_tbl[i].ci_offset =
pm8001_mr32(address, (offset + 0x18));
}
}
/**
* init_default_table_values - init the default table.
* @pm8001_ha: our hba card information
*/
static void __devinit
init_default_table_values(struct pm8001_hba_info *pm8001_ha)
{
int qn = 1;
int i;
u32 offsetib, offsetob;
void __iomem *addressib = pm8001_ha->inbnd_q_tbl_addr;
void __iomem *addressob = pm8001_ha->outbnd_q_tbl_addr;
pm8001_ha->main_cfg_tbl.inbound_q_nppd_hppd = 0;
pm8001_ha->main_cfg_tbl.outbound_hw_event_pid0_3 = 0;
pm8001_ha->main_cfg_tbl.outbound_hw_event_pid4_7 = 0;
pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid0_3 = 0;
pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid4_7 = 0;
pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid0_3 = 0;
pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid4_7 = 0;
pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid0_3 = 0;
pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid4_7 = 0;
pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid0_3 = 0;
pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid4_7 = 0;
pm8001_ha->main_cfg_tbl.upper_event_log_addr =
pm8001_ha->memoryMap.region[AAP1].phys_addr_hi;
pm8001_ha->main_cfg_tbl.lower_event_log_addr =
pm8001_ha->memoryMap.region[AAP1].phys_addr_lo;
pm8001_ha->main_cfg_tbl.event_log_size = PM8001_EVENT_LOG_SIZE;
pm8001_ha->main_cfg_tbl.event_log_option = 0x01;
pm8001_ha->main_cfg_tbl.upper_iop_event_log_addr =
pm8001_ha->memoryMap.region[IOP].phys_addr_hi;
pm8001_ha->main_cfg_tbl.lower_iop_event_log_addr =
pm8001_ha->memoryMap.region[IOP].phys_addr_lo;
pm8001_ha->main_cfg_tbl.iop_event_log_size = PM8001_EVENT_LOG_SIZE;
pm8001_ha->main_cfg_tbl.iop_event_log_option = 0x01;
pm8001_ha->main_cfg_tbl.fatal_err_interrupt = 0x01;
for (i = 0; i < qn; i++) {
pm8001_ha->inbnd_q_tbl[i].element_pri_size_cnt =
PM8001_MPI_QUEUE | (64 << 16) | (0x00<<30);
pm8001_ha->inbnd_q_tbl[i].upper_base_addr =
pm8001_ha->memoryMap.region[IB].phys_addr_hi;
pm8001_ha->inbnd_q_tbl[i].lower_base_addr =
pm8001_ha->memoryMap.region[IB].phys_addr_lo;
pm8001_ha->inbnd_q_tbl[i].base_virt =
(u8 *)pm8001_ha->memoryMap.region[IB].virt_ptr;
pm8001_ha->inbnd_q_tbl[i].total_length =
pm8001_ha->memoryMap.region[IB].total_len;
pm8001_ha->inbnd_q_tbl[i].ci_upper_base_addr =
pm8001_ha->memoryMap.region[CI].phys_addr_hi;
pm8001_ha->inbnd_q_tbl[i].ci_lower_base_addr =
pm8001_ha->memoryMap.region[CI].phys_addr_lo;
pm8001_ha->inbnd_q_tbl[i].ci_virt =
pm8001_ha->memoryMap.region[CI].virt_ptr;
offsetib = i * 0x20;
pm8001_ha->inbnd_q_tbl[i].pi_pci_bar =
get_pci_bar_index(pm8001_mr32(addressib,
(offsetib + 0x14)));
pm8001_ha->inbnd_q_tbl[i].pi_offset =
pm8001_mr32(addressib, (offsetib + 0x18));
pm8001_ha->inbnd_q_tbl[i].producer_idx = 0;
pm8001_ha->inbnd_q_tbl[i].consumer_index = 0;
}
for (i = 0; i < qn; i++) {
pm8001_ha->outbnd_q_tbl[i].element_size_cnt =
PM8001_MPI_QUEUE | (64 << 16) | (0x01<<30);
pm8001_ha->outbnd_q_tbl[i].upper_base_addr =
pm8001_ha->memoryMap.region[OB].phys_addr_hi;
pm8001_ha->outbnd_q_tbl[i].lower_base_addr =
pm8001_ha->memoryMap.region[OB].phys_addr_lo;
pm8001_ha->outbnd_q_tbl[i].base_virt =
(u8 *)pm8001_ha->memoryMap.region[OB].virt_ptr;
pm8001_ha->outbnd_q_tbl[i].total_length =
pm8001_ha->memoryMap.region[OB].total_len;
pm8001_ha->outbnd_q_tbl[i].pi_upper_base_addr =
pm8001_ha->memoryMap.region[PI].phys_addr_hi;
pm8001_ha->outbnd_q_tbl[i].pi_lower_base_addr =
pm8001_ha->memoryMap.region[PI].phys_addr_lo;
pm8001_ha->outbnd_q_tbl[i].interrup_vec_cnt_delay =
0 | (10 << 16) | (0 << 24);
pm8001_ha->outbnd_q_tbl[i].pi_virt =
pm8001_ha->memoryMap.region[PI].virt_ptr;
offsetob = i * 0x24;
pm8001_ha->outbnd_q_tbl[i].ci_pci_bar =
get_pci_bar_index(pm8001_mr32(addressob,
offsetob + 0x14));
pm8001_ha->outbnd_q_tbl[i].ci_offset =
pm8001_mr32(addressob, (offsetob + 0x18));
pm8001_ha->outbnd_q_tbl[i].consumer_idx = 0;
pm8001_ha->outbnd_q_tbl[i].producer_index = 0;
}
}
/**
* update_main_config_table - update the main default table to the HBA.
* @pm8001_ha: our hba card information
*/
static void __devinit
update_main_config_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
pm8001_mw32(address, 0x24,
pm8001_ha->main_cfg_tbl.inbound_q_nppd_hppd);
pm8001_mw32(address, 0x28,
pm8001_ha->main_cfg_tbl.outbound_hw_event_pid0_3);
pm8001_mw32(address, 0x2C,
pm8001_ha->main_cfg_tbl.outbound_hw_event_pid4_7);
pm8001_mw32(address, 0x30,
pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid0_3);
pm8001_mw32(address, 0x34,
pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid4_7);
pm8001_mw32(address, 0x38,
pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid0_3);
pm8001_mw32(address, 0x3C,
pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid4_7);
pm8001_mw32(address, 0x40,
pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid0_3);
pm8001_mw32(address, 0x44,
pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid4_7);
pm8001_mw32(address, 0x48,
pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid0_3);
pm8001_mw32(address, 0x4C,
pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid4_7);
pm8001_mw32(address, 0x50,
pm8001_ha->main_cfg_tbl.upper_event_log_addr);
pm8001_mw32(address, 0x54,
pm8001_ha->main_cfg_tbl.lower_event_log_addr);
pm8001_mw32(address, 0x58, pm8001_ha->main_cfg_tbl.event_log_size);
pm8001_mw32(address, 0x5C, pm8001_ha->main_cfg_tbl.event_log_option);
pm8001_mw32(address, 0x60,
pm8001_ha->main_cfg_tbl.upper_iop_event_log_addr);
pm8001_mw32(address, 0x64,
pm8001_ha->main_cfg_tbl.lower_iop_event_log_addr);
pm8001_mw32(address, 0x68, pm8001_ha->main_cfg_tbl.iop_event_log_size);
pm8001_mw32(address, 0x6C,
pm8001_ha->main_cfg_tbl.iop_event_log_option);
pm8001_mw32(address, 0x70,
pm8001_ha->main_cfg_tbl.fatal_err_interrupt);
}
/**
* update_inbnd_queue_table - update the inbound queue table to the HBA.
* @pm8001_ha: our hba card information
*/
static void __devinit
update_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha, int number)
{
void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
u16 offset = number * 0x20;
pm8001_mw32(address, offset + 0x00,
pm8001_ha->inbnd_q_tbl[number].element_pri_size_cnt);
pm8001_mw32(address, offset + 0x04,
pm8001_ha->inbnd_q_tbl[number].upper_base_addr);
pm8001_mw32(address, offset + 0x08,
pm8001_ha->inbnd_q_tbl[number].lower_base_addr);
pm8001_mw32(address, offset + 0x0C,
pm8001_ha->inbnd_q_tbl[number].ci_upper_base_addr);
pm8001_mw32(address, offset + 0x10,
pm8001_ha->inbnd_q_tbl[number].ci_lower_base_addr);
}
/**
* update_outbnd_queue_table - update the outbound queue table to the HBA.
* @pm8001_ha: our hba card information
*/
static void __devinit
update_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha, int number)
{
void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
u16 offset = number * 0x24;
pm8001_mw32(address, offset + 0x00,
pm8001_ha->outbnd_q_tbl[number].element_size_cnt);
pm8001_mw32(address, offset + 0x04,
pm8001_ha->outbnd_q_tbl[number].upper_base_addr);
pm8001_mw32(address, offset + 0x08,
pm8001_ha->outbnd_q_tbl[number].lower_base_addr);
pm8001_mw32(address, offset + 0x0C,
pm8001_ha->outbnd_q_tbl[number].pi_upper_base_addr);
pm8001_mw32(address, offset + 0x10,
pm8001_ha->outbnd_q_tbl[number].pi_lower_base_addr);
pm8001_mw32(address, offset + 0x1C,
pm8001_ha->outbnd_q_tbl[number].interrup_vec_cnt_delay);
}
/**
* pm8001_bar4_shift - function is called to shift BAR base address
* @pm8001_ha : our hba card infomation
* @shiftValue : shifting value in memory bar.
*/
int pm8001_bar4_shift(struct pm8001_hba_info *pm8001_ha, u32 shiftValue)
{
u32 regVal;
unsigned long start;
/* program the inbound AXI translation Lower Address */
pm8001_cw32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW, shiftValue);
/* confirm the setting is written */
start = jiffies + HZ; /* 1 sec */
do {
regVal = pm8001_cr32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW);
} while ((regVal != shiftValue) && time_before(jiffies, start));
if (regVal != shiftValue) {
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("TIMEOUT:SPC_IBW_AXI_TRANSLATION_LOW"
" = 0x%x\n", regVal));
return -1;
}
return 0;
}
/**
* mpi_set_phys_g3_with_ssc
* @pm8001_ha: our hba card information
* @SSCbit: set SSCbit to 0 to disable all phys ssc; 1 to enable all phys ssc.
*/
static void __devinit
mpi_set_phys_g3_with_ssc(struct pm8001_hba_info *pm8001_ha, u32 SSCbit)
{
u32 value, offset, i;
unsigned long flags;
#define SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR 0x00030000
#define SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR 0x00040000
#define SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET 0x1074
#define SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET 0x1074
#define PHY_G3_WITHOUT_SSC_BIT_SHIFT 12
#define PHY_G3_WITH_SSC_BIT_SHIFT 13
#define SNW3_PHY_CAPABILITIES_PARITY 31
/*
* Using shifted destination address 0x3_0000:0x1074 + 0x4000*N (N=0:3)
* Using shifted destination address 0x4_0000:0x1074 + 0x4000*(N-4) (N=4:7)
*/
spin_lock_irqsave(&pm8001_ha->lock, flags);
if (-1 == pm8001_bar4_shift(pm8001_ha,
SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return;
}
for (i = 0; i < 4; i++) {
offset = SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET + 0x4000 * i;
pm8001_cw32(pm8001_ha, 2, offset, 0x80001501);
}
/* shift membase 3 for SAS2_SETTINGS_LOCAL_PHY 4 - 7 */
if (-1 == pm8001_bar4_shift(pm8001_ha,
SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return;
}
for (i = 4; i < 8; i++) {
offset = SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET + 0x4000 * (i-4);
pm8001_cw32(pm8001_ha, 2, offset, 0x80001501);
}
/*************************************************************
Change the SSC upspreading value to 0x0 so that upspreading is disabled.
Device MABC SMOD0 Controls
Address: (via MEMBASE-III):
Using shifted destination address 0x0_0000: with Offset 0xD8
31:28 R/W Reserved Do not change
27:24 R/W SAS_SMOD_SPRDUP 0000
23:20 R/W SAS_SMOD_SPRDDN 0000
19:0 R/W Reserved Do not change
Upon power-up this register will read as 0x8990c016,
and I would like you to change the SAS_SMOD_SPRDUP bits to 0b0000
so that the written value will be 0x8090c016.
This will ensure only down-spreading SSC is enabled on the SPC.
*************************************************************/
value = pm8001_cr32(pm8001_ha, 2, 0xd8);
pm8001_cw32(pm8001_ha, 2, 0xd8, 0x8000C016);
/*set the shifted destination address to 0x0 to avoid error operation */
pm8001_bar4_shift(pm8001_ha, 0x0);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return;
}
/**
* mpi_set_open_retry_interval_reg
* @pm8001_ha: our hba card information
* @interval - interval time for each OPEN_REJECT (RETRY). The units are in 1us.
*/
static void __devinit
mpi_set_open_retry_interval_reg(struct pm8001_hba_info *pm8001_ha,
u32 interval)
{
u32 offset;
u32 value;
u32 i;
unsigned long flags;
#define OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR 0x00030000
#define OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR 0x00040000
#define OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET 0x30B4
#define OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET 0x30B4
#define OPEN_RETRY_INTERVAL_REG_MASK 0x0000FFFF
value = interval & OPEN_RETRY_INTERVAL_REG_MASK;
spin_lock_irqsave(&pm8001_ha->lock, flags);
/* shift bar and set the OPEN_REJECT(RETRY) interval time of PHY 0 -3.*/
if (-1 == pm8001_bar4_shift(pm8001_ha,
OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return;
}
for (i = 0; i < 4; i++) {
offset = OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET + 0x4000 * i;
pm8001_cw32(pm8001_ha, 2, offset, value);
}
if (-1 == pm8001_bar4_shift(pm8001_ha,
OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return;
}
for (i = 4; i < 8; i++) {
offset = OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET + 0x4000 * (i-4);
pm8001_cw32(pm8001_ha, 2, offset, value);
}
/*set the shifted destination address to 0x0 to avoid error operation */
pm8001_bar4_shift(pm8001_ha, 0x0);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return;
}
/**
* mpi_init_check - check firmware initialization status.
* @pm8001_ha: our hba card information
*/
static int mpi_init_check(struct pm8001_hba_info *pm8001_ha)
{
u32 max_wait_count;
u32 value;
u32 gst_len_mpistate;
/* Write bit0=1 to Inbound DoorBell Register to tell the SPC FW the
table is updated */
pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_UPDATE);
/* wait until Inbound DoorBell Clear Register toggled */
max_wait_count = 1 * 1000 * 1000;/* 1 sec */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
value &= SPC_MSGU_CFG_TABLE_UPDATE;
} while ((value != 0) && (--max_wait_count));
if (!max_wait_count)
return -1;
/* check the MPI-State for initialization */
gst_len_mpistate =
pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
GST_GSTLEN_MPIS_OFFSET);
if (GST_MPI_STATE_INIT != (gst_len_mpistate & GST_MPI_STATE_MASK))
return -1;
/* check MPI Initialization error */
gst_len_mpistate = gst_len_mpistate >> 16;
if (0x0000 != gst_len_mpistate)
return -1;
return 0;
}
/**
* check_fw_ready - The LLDD check if the FW is ready, if not, return error.
* @pm8001_ha: our hba card information
*/
static int check_fw_ready(struct pm8001_hba_info *pm8001_ha)
{
u32 value, value1;
u32 max_wait_count;
/* check error state */
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
/* check AAP error */
if (SCRATCH_PAD1_ERR == (value & SCRATCH_PAD_STATE_MASK)) {
/* error state */
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
return -1;
}
/* check IOP error */
if (SCRATCH_PAD2_ERR == (value1 & SCRATCH_PAD_STATE_MASK)) {
/* error state */
value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3);
return -1;
}
/* bit 4-31 of scratch pad1 should be zeros if it is not
in error state*/
if (value & SCRATCH_PAD1_STATE_MASK) {
/* error case */
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
return -1;
}
/* bit 2, 4-31 of scratch pad2 should be zeros if it is not
in error state */
if (value1 & SCRATCH_PAD2_STATE_MASK) {
/* error case */
return -1;
}
max_wait_count = 1 * 1000 * 1000;/* 1 sec timeout */
/* wait until scratch pad 1 and 2 registers in ready state */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)
& SCRATCH_PAD1_RDY;
value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)
& SCRATCH_PAD2_RDY;
if ((--max_wait_count) == 0)
return -1;
} while ((value != SCRATCH_PAD1_RDY) || (value1 != SCRATCH_PAD2_RDY));
return 0;
}
static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *base_addr;
u32 value;
u32 offset;
u32 pcibar;
u32 pcilogic;
value = pm8001_cr32(pm8001_ha, 0, 0x44);
offset = value & 0x03FFFFFF;
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Scratchpad 0 Offset: %x\n", offset));
pcilogic = (value & 0xFC000000) >> 26;
pcibar = get_pci_bar_index(pcilogic);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Scratchpad 0 PCI BAR: %d\n", pcibar));
pm8001_ha->main_cfg_tbl_addr = base_addr =
pm8001_ha->io_mem[pcibar].memvirtaddr + offset;
pm8001_ha->general_stat_tbl_addr =
base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x18);
pm8001_ha->inbnd_q_tbl_addr =
base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x1C);
pm8001_ha->outbnd_q_tbl_addr =
base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x20);
}
/**
* pm8001_chip_init - the main init function that initialize whole PM8001 chip.
* @pm8001_ha: our hba card information
*/
static int __devinit pm8001_chip_init(struct pm8001_hba_info *pm8001_ha)
{
/* check the firmware status */
if (-1 == check_fw_ready(pm8001_ha)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Firmware is not ready!\n"));
return -EBUSY;
}
/* Initialize pci space address eg: mpi offset */
init_pci_device_addresses(pm8001_ha);
init_default_table_values(pm8001_ha);
read_main_config_table(pm8001_ha);
read_general_status_table(pm8001_ha);
read_inbnd_queue_table(pm8001_ha);
read_outbnd_queue_table(pm8001_ha);
/* update main config table ,inbound table and outbound table */
update_main_config_table(pm8001_ha);
update_inbnd_queue_table(pm8001_ha, 0);
update_outbnd_queue_table(pm8001_ha, 0);
mpi_set_phys_g3_with_ssc(pm8001_ha, 0);
/* 7->130ms, 34->500ms, 119->1.5s */
mpi_set_open_retry_interval_reg(pm8001_ha, 119);
/* notify firmware update finished and check initialization status */
if (0 == mpi_init_check(pm8001_ha)) {
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("MPI initialize successful!\n"));
} else
return -EBUSY;
/*This register is a 16-bit timer with a resolution of 1us. This is the
timer used for interrupt delay/coalescing in the PCIe Application Layer.
Zero is not a valid value. A value of 1 in the register will cause the
interrupts to be normal. A value greater than 1 will cause coalescing
delays.*/
pm8001_cw32(pm8001_ha, 1, 0x0033c0, 0x1);
pm8001_cw32(pm8001_ha, 1, 0x0033c4, 0x0);
return 0;
}
static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
{
u32 max_wait_count;
u32 value;
u32 gst_len_mpistate;
init_pci_device_addresses(pm8001_ha);
/* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
table is stop */
pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_RESET);
/* wait until Inbound DoorBell Clear Register toggled */
max_wait_count = 1 * 1000 * 1000;/* 1 sec */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
value &= SPC_MSGU_CFG_TABLE_RESET;
} while ((value != 0) && (--max_wait_count));
if (!max_wait_count) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("TIMEOUT:IBDB value/=0x%x\n", value));
return -1;
}
/* check the MPI-State for termination in progress */
/* wait until Inbound DoorBell Clear Register toggled */
max_wait_count = 1 * 1000 * 1000; /* 1 sec */
do {
udelay(1);
gst_len_mpistate =
pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
GST_GSTLEN_MPIS_OFFSET);
if (GST_MPI_STATE_UNINIT ==
(gst_len_mpistate & GST_MPI_STATE_MASK))
break;
} while (--max_wait_count);
if (!max_wait_count) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk(" TIME OUT MPI State = 0x%x\n",
gst_len_mpistate & GST_MPI_STATE_MASK));
return -1;
}
return 0;
}
/**
* soft_reset_ready_check - Function to check FW is ready for soft reset.
* @pm8001_ha: our hba card information
*/
static u32 soft_reset_ready_check(struct pm8001_hba_info *pm8001_ha)
{
u32 regVal, regVal1, regVal2;
if (mpi_uninit_check(pm8001_ha) != 0) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MPI state is not ready\n"));
return -1;
}
/* read the scratch pad 2 register bit 2 */
regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)
& SCRATCH_PAD2_FWRDY_RST;
if (regVal == SCRATCH_PAD2_FWRDY_RST) {
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Firmware is ready for reset .\n"));
} else {
unsigned long flags;
/* Trigger NMI twice via RB6 */
spin_lock_irqsave(&pm8001_ha->lock, flags);
if (-1 == pm8001_bar4_shift(pm8001_ha, RB6_ACCESS_REG)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
RB6_ACCESS_REG));
return -1;
}
pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET,
RB6_MAGIC_NUMBER_RST);
pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET, RB6_MAGIC_NUMBER_RST);
/* wait for 100 ms */
mdelay(100);
regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2) &
SCRATCH_PAD2_FWRDY_RST;
if (regVal != SCRATCH_PAD2_FWRDY_RST) {
regVal1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
regVal2 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("TIMEOUT:MSGU_SCRATCH_PAD1"
"=0x%x, MSGU_SCRATCH_PAD2=0x%x\n",
regVal1, regVal2));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3)));
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return -1;
}
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
}
return 0;
}
/**
* pm8001_chip_soft_rst - soft reset the PM8001 chip, so that the clear all
* the FW register status to the originated status.
* @pm8001_ha: our hba card information
* @signature: signature in host scratch pad0 register.
*/
static int
pm8001_chip_soft_rst(struct pm8001_hba_info *pm8001_ha, u32 signature)
{
u32 regVal, toggleVal;
u32 max_wait_count;
u32 regVal1, regVal2, regVal3;
unsigned long flags;
/* step1: Check FW is ready for soft reset */
if (soft_reset_ready_check(pm8001_ha) != 0) {
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("FW is not ready\n"));
return -1;
}
/* step 2: clear NMI status register on AAP1 and IOP, write the same
value to clear */
/* map 0x60000 to BAR4(0x20), BAR2(win) */
spin_lock_irqsave(&pm8001_ha->lock, flags);
if (-1 == pm8001_bar4_shift(pm8001_ha, MBIC_AAP1_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
MBIC_AAP1_ADDR_BASE));
return -1;
}
regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("MBIC - NMI Enable VPE0 (IOP)= 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP, 0x0);
/* map 0x70000 to BAR4(0x20), BAR2(win) */
if (-1 == pm8001_bar4_shift(pm8001_ha, MBIC_IOP_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
MBIC_IOP_ADDR_BASE));
return -1;
}
regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("MBIC - NMI Enable VPE0 (AAP1)= 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1, 0x0);
regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PCIE -Event Interrupt Enable = 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE, 0x0);
regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PCIE - Event Interrupt = 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT, regVal);
regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PCIE -Error Interrupt Enable = 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE, 0x0);
regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PCIE - Error Interrupt = 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT, regVal);
/* read the scratch pad 1 register bit 2 */
regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)
& SCRATCH_PAD1_RST;
toggleVal = regVal ^ SCRATCH_PAD1_RST;
/* set signature in host scratch pad0 register to tell SPC that the
host performs the soft reset */
pm8001_cw32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_0, signature);
/* read required registers for confirmming */
/* map 0x0700000 to BAR4(0x20), BAR2(win) */
if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
GSM_ADDR_BASE));
return -1;
}
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x0(0x00007b88)-GSM Configuration and"
" Reset = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
/* step 3: host read GSM Configuration and Reset register */
regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET);
/* Put those bits to low */
/* GSM XCBI offset = 0x70 0000
0x00 Bit 13 COM_SLV_SW_RSTB 1
0x00 Bit 12 QSSP_SW_RSTB 1
0x00 Bit 11 RAAE_SW_RSTB 1
0x00 Bit 9 RB_1_SW_RSTB 1
0x00 Bit 8 SM_SW_RSTB 1
*/
regVal &= ~(0x00003b00);
/* host write GSM Configuration and Reset register */
pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x0 (0x00007b88 ==> 0x00004088) - GSM "
"Configuration and Reset is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
/* step 4: */
/* disable GSM - Read Address Parity Check */
regVal1 = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700038 - Read Address Parity Check "
"Enable = 0x%x\n", regVal1));
pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, 0x0);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable"
"is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK)));
/* disable GSM - Write Address Parity Check */
regVal2 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700040 - Write Address Parity Check"
" Enable = 0x%x\n", regVal2));
pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, 0x0);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700040 - Write Address Parity Check "
"Enable is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK)));
/* disable GSM - Write Data Parity Check */
regVal3 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x300048 - Write Data Parity Check"
" Enable = 0x%x\n", regVal3));
pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, 0x0);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x300048 - Write Data Parity Check Enable"
"is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK)));
/* step 5: delay 10 usec */
udelay(10);
/* step 5-b: set GPIO-0 output control to tristate anyway */
if (-1 == pm8001_bar4_shift(pm8001_ha, GPIO_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
GPIO_ADDR_BASE));
return -1;
}
regVal = pm8001_cr32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GPIO Output Control Register:"
" = 0x%x\n", regVal));
/* set GPIO-0 output control to tri-state */
regVal &= 0xFFFFFFFC;
pm8001_cw32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET, regVal);
/* Step 6: Reset the IOP and AAP1 */
/* map 0x00000 to BAR4(0x20), BAR2(win) */
if (-1 == pm8001_bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SPC Shift Bar4 to 0x%x failed\n",
SPC_TOP_LEVEL_ADDR_BASE));
return -1;
}
regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Top Register before resetting IOP/AAP1"
":= 0x%x\n", regVal));
regVal &= ~(SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS);
pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
/* step 7: Reset the BDMA/OSSP */
regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Top Register before resetting BDMA/OSSP"
": = 0x%x\n", regVal));
regVal &= ~(SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP);
pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
/* step 8: delay 10 usec */
udelay(10);
/* step 9: bring the BDMA and OSSP out of reset */
regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Top Register before bringing up BDMA/OSSP"
":= 0x%x\n", regVal));
regVal |= (SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP);
pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
/* step 10: delay 10 usec */
udelay(10);
/* step 11: reads and sets the GSM Configuration and Reset Register */
/* map 0x0700000 to BAR4(0x20), BAR2(win) */
if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SPC Shift Bar4 to 0x%x failed\n",
GSM_ADDR_BASE));
return -1;
}
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x0 (0x00007b88)-GSM Configuration and "
"Reset = 0x%x\n", pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET);
/* Put those bits to high */
/* GSM XCBI offset = 0x70 0000
0x00 Bit 13 COM_SLV_SW_RSTB 1
0x00 Bit 12 QSSP_SW_RSTB 1
0x00 Bit 11 RAAE_SW_RSTB 1
0x00 Bit 9 RB_1_SW_RSTB 1
0x00 Bit 8 SM_SW_RSTB 1
*/
regVal |= (GSM_CONFIG_RESET_VALUE);
pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM (0x00004088 ==> 0x00007b88) - GSM"
" Configuration and Reset is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET)));
/* step 12: Restore GSM - Read Address Parity Check */
regVal = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK);
/* just for debugging */
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable"
" = 0x%x\n", regVal));
pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, regVal1);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700038 - Read Address Parity"
" Check Enable is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK)));
/* Restore GSM - Write Address Parity Check */
regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK);
pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, regVal2);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700040 - Write Address Parity Check"
" Enable is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK)));
/* Restore GSM - Write Data Parity Check */
regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK);
pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, regVal3);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GSM 0x700048 - Write Data Parity Check Enable"
"is set to = 0x%x\n",
pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK)));
/* step 13: bring the IOP and AAP1 out of reset */
/* map 0x00000 to BAR4(0x20), BAR2(win) */
if (-1 == pm8001_bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
SPC_TOP_LEVEL_ADDR_BASE));
return -1;
}
regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET);
regVal |= (SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS);
pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal);
/* step 14: delay 10 usec - Normal Mode */
udelay(10);
/* check Soft Reset Normal mode or Soft Reset HDA mode */
if (signature == SPC_SOFT_RESET_SIGNATURE) {
/* step 15 (Normal Mode): wait until scratch pad1 register
bit 2 toggled */
max_wait_count = 2 * 1000 * 1000;/* 2 sec */
do {
udelay(1);
regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) &
SCRATCH_PAD1_RST;
} while ((regVal != toggleVal) && (--max_wait_count));
if (!max_wait_count) {
regVal = pm8001_cr32(pm8001_ha, 0,
MSGU_SCRATCH_PAD_1);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("TIMEOUT : ToggleVal 0x%x,"
"MSGU_SCRATCH_PAD1 = 0x%x\n",
toggleVal, regVal));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0,
MSGU_SCRATCH_PAD_0)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD2 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0,
MSGU_SCRATCH_PAD_2)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0,
MSGU_SCRATCH_PAD_3)));
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return -1;
}
/* step 16 (Normal) - Clear ODMR and ODCR */
pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);
/* step 17 (Normal Mode): wait for the FW and IOP to get
ready - 1 sec timeout */
/* Wait for the SPC Configuration Table to be ready */
if (check_fw_ready(pm8001_ha) == -1) {
regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
/* return error if MPI Configuration Table not ready */
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("FW not ready SCRATCH_PAD1"
" = 0x%x\n", regVal));
regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
/* return error if MPI Configuration Table not ready */
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("FW not ready SCRATCH_PAD2"
" = 0x%x\n", regVal));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD0 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0,
MSGU_SCRATCH_PAD_0)));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SCRATCH_PAD3 value = 0x%x\n",
pm8001_cr32(pm8001_ha, 0,
MSGU_SCRATCH_PAD_3)));
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return -1;
}
}
pm8001_bar4_shift(pm8001_ha, 0);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SPC soft reset Complete\n"));
return 0;
}
static void pm8001_hw_chip_rst(struct pm8001_hba_info *pm8001_ha)
{
u32 i;
u32 regVal;
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("chip reset start\n"));
/* do SPC chip reset. */
regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET);
regVal &= ~(SPC_REG_RESET_DEVICE);
pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal);
/* delay 10 usec */
udelay(10);
/* bring chip reset out of reset */
regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET);
regVal |= SPC_REG_RESET_DEVICE;
pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal);
/* delay 10 usec */
udelay(10);
/* wait for 20 msec until the firmware gets reloaded */
i = 20;
do {
mdelay(1);
} while ((--i) != 0);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("chip reset finished\n"));
}
/**
* pm8001_chip_iounmap - which maped when initialized.
* @pm8001_ha: our hba card information
*/
static void pm8001_chip_iounmap(struct pm8001_hba_info *pm8001_ha)
{
s8 bar, logical = 0;
for (bar = 0; bar < 6; bar++) {
/*
** logical BARs for SPC:
** bar 0 and 1 - logical BAR0
** bar 2 and 3 - logical BAR1
** bar4 - logical BAR2
** bar5 - logical BAR3
** Skip the appropriate assignments:
*/
if ((bar == 1) || (bar == 3))
continue;
if (pm8001_ha->io_mem[logical].memvirtaddr) {
iounmap(pm8001_ha->io_mem[logical].memvirtaddr);
logical++;
}
}
}
/**
* pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm8001_chip_intx_interrupt_enable(struct pm8001_hba_info *pm8001_ha)
{
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);
pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
}
/**
* pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm8001_chip_intx_interrupt_disable(struct pm8001_hba_info *pm8001_ha)
{
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_MASK_ALL);
}
/**
* pm8001_chip_msix_interrupt_enable - enable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm8001_chip_msix_interrupt_enable(struct pm8001_hba_info *pm8001_ha,
u32 int_vec_idx)
{
u32 msi_index;
u32 value;
msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE;
msi_index += MSIX_TABLE_BASE;
pm8001_cw32(pm8001_ha, 0, msi_index, MSIX_INTERRUPT_ENABLE);
value = (1 << int_vec_idx);
pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, value);
}
/**
* pm8001_chip_msix_interrupt_disable - disable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm8001_chip_msix_interrupt_disable(struct pm8001_hba_info *pm8001_ha,
u32 int_vec_idx)
{
u32 msi_index;
msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE;
msi_index += MSIX_TABLE_BASE;
pm8001_cw32(pm8001_ha, 0, msi_index, MSIX_INTERRUPT_DISABLE);
}
/**
* pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm8001_chip_interrupt_enable(struct pm8001_hba_info *pm8001_ha)
{
#ifdef PM8001_USE_MSIX
pm8001_chip_msix_interrupt_enable(pm8001_ha, 0);
return;
#endif
pm8001_chip_intx_interrupt_enable(pm8001_ha);
}
/**
* pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm8001_chip_interrupt_disable(struct pm8001_hba_info *pm8001_ha)
{
#ifdef PM8001_USE_MSIX
pm8001_chip_msix_interrupt_disable(pm8001_ha, 0);
return;
#endif
pm8001_chip_intx_interrupt_disable(pm8001_ha);
}
/**
* mpi_msg_free_get- get the free message buffer for transfer inbound queue.
* @circularQ: the inbound queue we want to transfer to HBA.
* @messageSize: the message size of this transfer, normally it is 64 bytes
* @messagePtr: the pointer to message.
*/
static int mpi_msg_free_get(struct inbound_queue_table *circularQ,
u16 messageSize, void **messagePtr)
{
u32 offset, consumer_index;
struct mpi_msg_hdr *msgHeader;
u8 bcCount = 1; /* only support single buffer */
/* Checks is the requested message size can be allocated in this queue*/
if (messageSize > 64) {
*messagePtr = NULL;
return -1;
}
/* Stores the new consumer index */
consumer_index = pm8001_read_32(circularQ->ci_virt);
circularQ->consumer_index = cpu_to_le32(consumer_index);
if (((circularQ->producer_idx + bcCount) % PM8001_MPI_QUEUE) ==
le32_to_cpu(circularQ->consumer_index)) {
*messagePtr = NULL;
return -1;
}
/* get memory IOMB buffer address */
offset = circularQ->producer_idx * 64;
/* increment to next bcCount element */
circularQ->producer_idx = (circularQ->producer_idx + bcCount)
% PM8001_MPI_QUEUE;
/* Adds that distance to the base of the region virtual address plus
the message header size*/
msgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt + offset);
*messagePtr = ((void *)msgHeader) + sizeof(struct mpi_msg_hdr);
return 0;
}
/**
* mpi_build_cmd- build the message queue for transfer, update the PI to FW
* to tell the fw to get this message from IOMB.
* @pm8001_ha: our hba card information
* @circularQ: the inbound queue we want to transfer to HBA.
* @opCode: the operation code represents commands which LLDD and fw recognized.
* @payload: the command payload of each operation command.
*/
static int mpi_build_cmd(struct pm8001_hba_info *pm8001_ha,
struct inbound_queue_table *circularQ,
u32 opCode, void *payload)
{
u32 Header = 0, hpriority = 0, bc = 1, category = 0x02;
u32 responseQueue = 0;
void *pMessage;
if (mpi_msg_free_get(circularQ, 64, &pMessage) < 0) {
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("No free mpi buffer\n"));
return -1;
}
BUG_ON(!payload);
/*Copy to the payload*/
memcpy(pMessage, payload, (64 - sizeof(struct mpi_msg_hdr)));
/*Build the header*/
Header = ((1 << 31) | (hpriority << 30) | ((bc & 0x1f) << 24)
| ((responseQueue & 0x3F) << 16)
| ((category & 0xF) << 12) | (opCode & 0xFFF));
pm8001_write_32((pMessage - 4), 0, cpu_to_le32(Header));
/*Update the PI to the firmware*/
pm8001_cw32(pm8001_ha, circularQ->pi_pci_bar,
circularQ->pi_offset, circularQ->producer_idx);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("after PI= %d CI= %d\n", circularQ->producer_idx,
circularQ->consumer_index));
return 0;
}
static u32 mpi_msg_free_set(struct pm8001_hba_info *pm8001_ha, void *pMsg,
struct outbound_queue_table *circularQ, u8 bc)
{
u32 producer_index;
struct mpi_msg_hdr *msgHeader;
struct mpi_msg_hdr *pOutBoundMsgHeader;
msgHeader = (struct mpi_msg_hdr *)(pMsg - sizeof(struct mpi_msg_hdr));
pOutBoundMsgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt +
circularQ->consumer_idx * 64);
if (pOutBoundMsgHeader != msgHeader) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("consumer_idx = %d msgHeader = %p\n",
circularQ->consumer_idx, msgHeader));
/* Update the producer index from SPC */
producer_index = pm8001_read_32(circularQ->pi_virt);
circularQ->producer_index = cpu_to_le32(producer_index);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("consumer_idx = %d producer_index = %d"
"msgHeader = %p\n", circularQ->consumer_idx,
circularQ->producer_index, msgHeader));
return 0;
}
/* free the circular queue buffer elements associated with the message*/
circularQ->consumer_idx = (circularQ->consumer_idx + bc)
% PM8001_MPI_QUEUE;
/* update the CI of outbound queue */
pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar, circularQ->ci_offset,
circularQ->consumer_idx);
/* Update the producer index from SPC*/
producer_index = pm8001_read_32(circularQ->pi_virt);
circularQ->producer_index = cpu_to_le32(producer_index);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk(" CI=%d PI=%d\n", circularQ->consumer_idx,
circularQ->producer_index));
return 0;
}
/**
* mpi_msg_consume- get the MPI message from outbound queue message table.
* @pm8001_ha: our hba card information
* @circularQ: the outbound queue table.
* @messagePtr1: the message contents of this outbound message.
* @pBC: the message size.
*/
static u32 mpi_msg_consume(struct pm8001_hba_info *pm8001_ha,
struct outbound_queue_table *circularQ,
void **messagePtr1, u8 *pBC)
{
struct mpi_msg_hdr *msgHeader;
__le32 msgHeader_tmp;
u32 header_tmp;
do {
/* If there are not-yet-delivered messages ... */
if (le32_to_cpu(circularQ->producer_index)
!= circularQ->consumer_idx) {
/*Get the pointer to the circular queue buffer element*/
msgHeader = (struct mpi_msg_hdr *)
(circularQ->base_virt +
circularQ->consumer_idx * 64);
/* read header */
header_tmp = pm8001_read_32(msgHeader);
msgHeader_tmp = cpu_to_le32(header_tmp);
if (0 != (le32_to_cpu(msgHeader_tmp) & 0x80000000)) {
if (OPC_OUB_SKIP_ENTRY !=
(le32_to_cpu(msgHeader_tmp) & 0xfff)) {
*messagePtr1 =
((u8 *)msgHeader) +
sizeof(struct mpi_msg_hdr);
*pBC = (u8)((le32_to_cpu(msgHeader_tmp)
>> 24) & 0x1f);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk(": CI=%d PI=%d "
"msgHeader=%x\n",
circularQ->consumer_idx,
circularQ->producer_index,
msgHeader_tmp));
return MPI_IO_STATUS_SUCCESS;
} else {
circularQ->consumer_idx =
(circularQ->consumer_idx +
((le32_to_cpu(msgHeader_tmp)
>> 24) & 0x1f))
% PM8001_MPI_QUEUE;
msgHeader_tmp = 0;
pm8001_write_32(msgHeader, 0, 0);
/* update the CI of outbound queue */
pm8001_cw32(pm8001_ha,
circularQ->ci_pci_bar,
circularQ->ci_offset,
circularQ->consumer_idx);
}
} else {
circularQ->consumer_idx =
(circularQ->consumer_idx +
((le32_to_cpu(msgHeader_tmp) >> 24) &
0x1f)) % PM8001_MPI_QUEUE;
msgHeader_tmp = 0;
pm8001_write_32(msgHeader, 0, 0);
/* update the CI of outbound queue */
pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar,
circularQ->ci_offset,
circularQ->consumer_idx);
return MPI_IO_STATUS_FAIL;
}
} else {
u32 producer_index;
void *pi_virt = circularQ->pi_virt;
/* Update the producer index from SPC */
producer_index = pm8001_read_32(pi_virt);
circularQ->producer_index = cpu_to_le32(producer_index);
}
} while (le32_to_cpu(circularQ->producer_index) !=
circularQ->consumer_idx);
/* while we don't have any more not-yet-delivered message */
/* report empty */
return MPI_IO_STATUS_BUSY;
}
static void pm8001_work_fn(struct work_struct *work)
{
struct pm8001_work *pw = container_of(work, struct pm8001_work, work);
struct pm8001_device *pm8001_dev;
struct domain_device *dev;
/*
* So far, all users of this stash an associated structure here.
* If we get here, and this pointer is null, then the action
* was cancelled. This nullification happens when the device
* goes away.
*/
pm8001_dev = pw->data; /* Most stash device structure */
if ((pm8001_dev == NULL)
|| ((pw->handler != IO_XFER_ERROR_BREAK)
&& (pm8001_dev->dev_type == NO_DEVICE))) {
kfree(pw);
return;
}
switch (pw->handler) {
case IO_XFER_ERROR_BREAK:
{ /* This one stashes the sas_task instead */
struct sas_task *t = (struct sas_task *)pm8001_dev;
u32 tag;
struct pm8001_ccb_info *ccb;
struct pm8001_hba_info *pm8001_ha = pw->pm8001_ha;
unsigned long flags, flags1;
struct task_status_struct *ts;
int i;
if (pm8001_query_task(t) == TMF_RESP_FUNC_SUCC)
break; /* Task still on lu */
spin_lock_irqsave(&pm8001_ha->lock, flags);
spin_lock_irqsave(&t->task_state_lock, flags1);
if (unlikely((t->task_state_flags & SAS_TASK_STATE_DONE))) {
spin_unlock_irqrestore(&t->task_state_lock, flags1);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
break; /* Task got completed by another */
}
spin_unlock_irqrestore(&t->task_state_lock, flags1);
/* Search for a possible ccb that matches the task */
for (i = 0; ccb = NULL, i < PM8001_MAX_CCB; i++) {
ccb = &pm8001_ha->ccb_info[i];
tag = ccb->ccb_tag;
if ((tag != 0xFFFFFFFF) && (ccb->task == t))
break;
}
if (!ccb) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
break; /* Task got freed by another */
}
ts = &t->task_status;
ts->resp = SAS_TASK_COMPLETE;
/* Force the midlayer to retry */
ts->stat = SAS_QUEUE_FULL;
pm8001_dev = ccb->device;
if (pm8001_dev)
pm8001_dev->running_req--;
spin_lock_irqsave(&t->task_state_lock, flags1);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags1);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p"
" done with event 0x%x resp 0x%x stat 0x%x but"
" aborted by upper layer!\n",
t, pw->handler, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags1);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
t->task_done(t);
}
} break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
{ /* This one stashes the sas_task instead */
struct sas_task *t = (struct sas_task *)pm8001_dev;
u32 tag;
struct pm8001_ccb_info *ccb;
struct pm8001_hba_info *pm8001_ha = pw->pm8001_ha;
unsigned long flags, flags1;
int i, ret = 0;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ret = pm8001_query_task(t);
PM8001_IO_DBG(pm8001_ha,
switch (ret) {
case TMF_RESP_FUNC_SUCC:
pm8001_printk("...Task on lu\n");
break;
case TMF_RESP_FUNC_COMPLETE:
pm8001_printk("...Task NOT on lu\n");
break;
default:
pm8001_printk("...query task failed!!!\n");
break;
});
spin_lock_irqsave(&pm8001_ha->lock, flags);
spin_lock_irqsave(&t->task_state_lock, flags1);
if (unlikely((t->task_state_flags & SAS_TASK_STATE_DONE))) {
spin_unlock_irqrestore(&t->task_state_lock, flags1);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
if (ret == TMF_RESP_FUNC_SUCC) /* task on lu */
(void)pm8001_abort_task(t);
break; /* Task got completed by another */
}
spin_unlock_irqrestore(&t->task_state_lock, flags1);
/* Search for a possible ccb that matches the task */
for (i = 0; ccb = NULL, i < PM8001_MAX_CCB; i++) {
ccb = &pm8001_ha->ccb_info[i];
tag = ccb->ccb_tag;
if ((tag != 0xFFFFFFFF) && (ccb->task == t))
break;
}
if (!ccb) {
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
if (ret == TMF_RESP_FUNC_SUCC) /* task on lu */
(void)pm8001_abort_task(t);
break; /* Task got freed by another */
}
pm8001_dev = ccb->device;
dev = pm8001_dev->sas_device;
switch (ret) {
case TMF_RESP_FUNC_SUCC: /* task on lu */
ccb->open_retry = 1; /* Snub completion */
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
ret = pm8001_abort_task(t);
ccb->open_retry = 0;
switch (ret) {
case TMF_RESP_FUNC_SUCC:
case TMF_RESP_FUNC_COMPLETE:
break;
default: /* device misbehavior */
ret = TMF_RESP_FUNC_FAILED;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("...Reset phy\n"));
pm8001_I_T_nexus_reset(dev);
break;
}
break;
case TMF_RESP_FUNC_COMPLETE: /* task not on lu */
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
/* Do we need to abort the task locally? */
break;
default: /* device misbehavior */
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
ret = TMF_RESP_FUNC_FAILED;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("...Reset phy\n"));
pm8001_I_T_nexus_reset(dev);
}
if (ret == TMF_RESP_FUNC_FAILED)
t = NULL;
pm8001_open_reject_retry(pm8001_ha, t, pm8001_dev);
PM8001_IO_DBG(pm8001_ha, pm8001_printk("...Complete\n"));
} break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
dev = pm8001_dev->sas_device;
pm8001_I_T_nexus_reset(dev);
break;
case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
dev = pm8001_dev->sas_device;
pm8001_I_T_nexus_reset(dev);
break;
case IO_DS_IN_ERROR:
dev = pm8001_dev->sas_device;
pm8001_I_T_nexus_reset(dev);
break;
case IO_DS_NON_OPERATIONAL:
dev = pm8001_dev->sas_device;
pm8001_I_T_nexus_reset(dev);
break;
}
kfree(pw);
}
static int pm8001_handle_event(struct pm8001_hba_info *pm8001_ha, void *data,
int handler)
{
struct pm8001_work *pw;
int ret = 0;
pw = kmalloc(sizeof(struct pm8001_work), GFP_ATOMIC);
if (pw) {
pw->pm8001_ha = pm8001_ha;
pw->data = data;
pw->handler = handler;
INIT_WORK(&pw->work, pm8001_work_fn);
queue_work(pm8001_wq, &pw->work);
} else
ret = -ENOMEM;
return ret;
}
/**
* mpi_ssp_completion- process the event that FW response to the SSP request.
* @pm8001_ha: our hba card information
* @piomb: the message contents of this outbound message.
*
* When FW has completed a ssp request for example a IO request, after it has
* filled the SG data with the data, it will trigger this event represent
* that he has finished the job,please check the coresponding buffer.
* So we will tell the caller who maybe waiting the result to tell upper layer
* that the task has been finished.
*/
static void
mpi_ssp_completion(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
struct sas_task *t;
struct pm8001_ccb_info *ccb;
unsigned long flags;
u32 status;
u32 param;
u32 tag;
struct ssp_completion_resp *psspPayload;
struct task_status_struct *ts;
struct ssp_response_iu *iu;
struct pm8001_device *pm8001_dev;
psspPayload = (struct ssp_completion_resp *)(piomb + 4);
status = le32_to_cpu(psspPayload->status);
tag = le32_to_cpu(psspPayload->tag);
ccb = &pm8001_ha->ccb_info[tag];
if ((status == IO_ABORTED) && ccb->open_retry) {
/* Being completed by another */
ccb->open_retry = 0;
return;
}
pm8001_dev = ccb->device;
param = le32_to_cpu(psspPayload->param);
t = ccb->task;
if (status && status != IO_UNDERFLOW)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("sas IO status 0x%x\n", status));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
ts = &t->task_status;
switch (status) {
case IO_SUCCESS:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS"
",param = %d\n", param));
if (param == 0) {
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
} else {
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_PROTO_RESPONSE;
ts->residual = param;
iu = &psspPayload->ssp_resp_iu;
sas_ssp_task_response(pm8001_ha->dev, t, iu);
}
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ABORTED IOMB Tag\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
break;
case IO_UNDERFLOW:
/* SSP Completion with error */
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW"
",param = %d\n", param));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
ts->residual = param;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_NO_DEVICE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_NO_DEVICE\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_PHY_DOWN;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
/* Force the midlayer to retry */
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
if (!t->uldd_task)
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
"NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_DMA:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_DMA\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_OFFSET_MISMATCH:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_PORT_IN_RESET:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_PORT_IN_RESET\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_DS_NON_OPERATIONAL:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
if (!t->uldd_task)
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_DS_NON_OPERATIONAL);
break;
case IO_DS_IN_RECOVERY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_RECOVERY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_TM_TAG_NOT_FOUND:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_TM_TAG_NOT_FOUND\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_SSP_EXT_IU_ZERO_LEN_ERROR:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_SSP_EXT_IU_ZERO_LEN_ERROR\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
default:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", status));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
}
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("scsi_status = %x \n ",
psspPayload->ssp_resp_iu.status));
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
" io_status 0x%x resp 0x%x "
"stat 0x%x but aborted by upper layer!\n",
t, status, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
t->task_done(t);
}
}
/*See the comments for mpi_ssp_completion */
static void mpi_ssp_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
struct sas_task *t;
unsigned long flags;
struct task_status_struct *ts;
struct pm8001_ccb_info *ccb;
struct pm8001_device *pm8001_dev;
struct ssp_event_resp *psspPayload =
(struct ssp_event_resp *)(piomb + 4);
u32 event = le32_to_cpu(psspPayload->event);
u32 tag = le32_to_cpu(psspPayload->tag);
u32 port_id = le32_to_cpu(psspPayload->port_id);
u32 dev_id = le32_to_cpu(psspPayload->device_id);
ccb = &pm8001_ha->ccb_info[tag];
t = ccb->task;
pm8001_dev = ccb->device;
if (event)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("sas IO status 0x%x\n", event));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
ts = &t->task_status;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("port_id = %x,device_id = %x\n",
port_id, dev_id));
switch (event) {
case IO_OVERFLOW:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n");)
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
ts->residual = 0;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
pm8001_handle_event(pm8001_ha, t, IO_XFER_ERROR_BREAK);
return;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
"_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
if (!t->uldd_task)
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
"NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
pm8001_handle_event(pm8001_ha, t, IO_XFER_OPEN_RETRY_TIMEOUT);
return;
case IO_XFER_ERROR_UNEXPECTED_PHASE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_XFER_RDY_OVERRUN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_OFFSET_MISMATCH:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_CMD_FRAME_ISSUED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk(" IO_XFER_CMD_FRAME_ISSUED\n"));
return;
default:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", event));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
" event 0x%x resp 0x%x "
"stat 0x%x but aborted by upper layer!\n",
t, event, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
t->task_done(t);
}
}
/*See the comments for mpi_ssp_completion */
static void
mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct sas_task *t;
struct pm8001_ccb_info *ccb;
u32 param;
u32 status;
u32 tag;
struct sata_completion_resp *psataPayload;
struct task_status_struct *ts;
struct ata_task_resp *resp ;
u32 *sata_resp;
struct pm8001_device *pm8001_dev;
unsigned long flags;
psataPayload = (struct sata_completion_resp *)(piomb + 4);
status = le32_to_cpu(psataPayload->status);
tag = le32_to_cpu(psataPayload->tag);
ccb = &pm8001_ha->ccb_info[tag];
param = le32_to_cpu(psataPayload->param);
t = ccb->task;
ts = &t->task_status;
pm8001_dev = ccb->device;
if (status)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("sata IO status 0x%x\n", status));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
switch (status) {
case IO_SUCCESS:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
if (param == 0) {
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
} else {
u8 len;
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_PROTO_RESPONSE;
ts->residual = param;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("SAS_PROTO_RESPONSE len = %d\n",
param));
sata_resp = &psataPayload->sata_resp[0];
resp = (struct ata_task_resp *)ts->buf;
if (t->ata_task.dma_xfer == 0 &&
t->data_dir == PCI_DMA_FROMDEVICE) {
len = sizeof(struct pio_setup_fis);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("PIO read len = %d\n", len));
} else if (t->ata_task.use_ncq) {
len = sizeof(struct set_dev_bits_fis);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("FPDMA len = %d\n", len));
} else {
len = sizeof(struct dev_to_host_fis);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("other len = %d\n", len));
}
if (SAS_STATUS_BUF_SIZE >= sizeof(*resp)) {
resp->frame_len = len;
memcpy(&resp->ending_fis[0], sata_resp, len);
ts->buf_valid_size = sizeof(*resp);
} else
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("response to large\n"));
}
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ABORTED IOMB Tag\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
/* following cases are to do cases */
case IO_UNDERFLOW:
/* SATA Completion with error */
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_UNDERFLOW param = %d\n", param));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
ts->residual = param;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_NO_DEVICE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_NO_DEVICE\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_PHY_DOWN;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_INTERRUPTED;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
"_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*in order to force CPU ordering*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
return;
}
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
return;
}
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
"NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_STP_RESOURCES"
"_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
return;
}
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_DMA:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_DMA\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
break;
case IO_XFER_ERROR_SATA_LINK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_SATA_LINK_TIMEOUT\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_XFER_ERROR_REJECTED_NCQ_MODE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_PORT_IN_RESET:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_PORT_IN_RESET\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_DS_NON_OPERATIONAL:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha, pm8001_dev,
IO_DS_NON_OPERATIONAL);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
return;
}
break;
case IO_DS_IN_RECOVERY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk(" IO_DS_IN_RECOVERY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_DS_IN_ERROR:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_ERROR\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha, pm8001_dev,
IO_DS_IN_ERROR);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
return;
}
break;
case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
default:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", status));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task 0x%p done with io_status 0x%x"
" resp 0x%x stat 0x%x but aborted by upper layer!\n",
t, status, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else if (t->uldd_task) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* ditto */
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
} else if (!t->uldd_task) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
}
}
/*See the comments for mpi_ssp_completion */
static void mpi_sata_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
struct sas_task *t;
struct task_status_struct *ts;
struct pm8001_ccb_info *ccb;
struct pm8001_device *pm8001_dev;
struct sata_event_resp *psataPayload =
(struct sata_event_resp *)(piomb + 4);
u32 event = le32_to_cpu(psataPayload->event);
u32 tag = le32_to_cpu(psataPayload->tag);
u32 port_id = le32_to_cpu(psataPayload->port_id);
u32 dev_id = le32_to_cpu(psataPayload->device_id);
unsigned long flags;
ccb = &pm8001_ha->ccb_info[tag];
t = ccb->task;
pm8001_dev = ccb->device;
if (event)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("sata IO status 0x%x\n", event));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
ts = &t->task_status;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("port_id = %x,device_id = %x\n",
port_id, dev_id));
switch (event) {
case IO_OVERFLOW:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
ts->residual = 0;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_INTERRUPTED;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT"
"_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
return;
}
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
"NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_PEER_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PEER_ABORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_REJECTED_NCQ_MODE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_UNEXPECTED_PHASE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_XFER_RDY_OVERRUN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_OFFSET_MISMATCH:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_CMD_FRAME_ISSUED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n"));
break;
case IO_XFER_PIO_SETUP_ERROR:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_PIO_SETUP_ERROR\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
default:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", event));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task 0x%p done with io_status 0x%x"
" resp 0x%x stat 0x%x but aborted by upper layer!\n",
t, event, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else if (t->uldd_task) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* ditto */
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
} else if (!t->uldd_task) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/*ditto*/
spin_unlock_irq(&pm8001_ha->lock);
t->task_done(t);
spin_lock_irq(&pm8001_ha->lock);
}
}
/*See the comments for mpi_ssp_completion */
static void
mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
u32 param;
struct sas_task *t;
struct pm8001_ccb_info *ccb;
unsigned long flags;
u32 status;
u32 tag;
struct smp_completion_resp *psmpPayload;
struct task_status_struct *ts;
struct pm8001_device *pm8001_dev;
psmpPayload = (struct smp_completion_resp *)(piomb + 4);
status = le32_to_cpu(psmpPayload->status);
tag = le32_to_cpu(psmpPayload->tag);
ccb = &pm8001_ha->ccb_info[tag];
param = le32_to_cpu(psmpPayload->param);
t = ccb->task;
ts = &t->task_status;
pm8001_dev = ccb->device;
if (status)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("smp IO status 0x%x\n", status));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
switch (status) {
case IO_SUCCESS:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ABORTED IOMB\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_OVERFLOW:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
ts->residual = 0;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_NO_DEVICE:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NO_DEVICE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_PHY_DOWN;
break;
case IO_ERROR_HW_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ERROR_HW_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_BUSY;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_BUSY;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_BUSY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_"
"NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_RX_FRAME:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_RX_FRAME\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_ERROR_INTERNAL_SMP_RESOURCE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ERROR_INTERNAL_SMP_RESOURCE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_QUEUE_FULL;
break;
case IO_PORT_IN_RESET:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_PORT_IN_RESET\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_DS_NON_OPERATIONAL:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_DS_IN_RECOVERY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_RECOVERY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
default:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", status));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
/* not allowed case. Therefore, return failed status */
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with"
" io_status 0x%x resp 0x%x "
"stat 0x%x but aborted by upper layer!\n",
t, status, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
t->task_done(t);
}
}
static void
mpi_set_dev_state_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct set_dev_state_resp *pPayload =
(struct set_dev_state_resp *)(piomb + 4);
u32 tag = le32_to_cpu(pPayload->tag);
struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
struct pm8001_device *pm8001_dev = ccb->device;
u32 status = le32_to_cpu(pPayload->status);
u32 device_id = le32_to_cpu(pPayload->device_id);
u8 pds = le32_to_cpu(pPayload->pds_nds) | PDS_BITS;
u8 nds = le32_to_cpu(pPayload->pds_nds) | NDS_BITS;
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Set device id = 0x%x state "
"from 0x%x to 0x%x status = 0x%x!\n",
device_id, pds, nds, status));
complete(pm8001_dev->setds_completion);
ccb->task = NULL;
ccb->ccb_tag = 0xFFFFFFFF;
pm8001_ccb_free(pm8001_ha, tag);
}
static void
mpi_set_nvmd_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct get_nvm_data_resp *pPayload =
(struct get_nvm_data_resp *)(piomb + 4);
u32 tag = le32_to_cpu(pPayload->tag);
struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
u32 dlen_status = le32_to_cpu(pPayload->dlen_status);
complete(pm8001_ha->nvmd_completion);
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Set nvm data complete!\n"));
if ((dlen_status & NVMD_STAT) != 0) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Set nvm data error!\n"));
return;
}
ccb->task = NULL;
ccb->ccb_tag = 0xFFFFFFFF;
pm8001_ccb_free(pm8001_ha, tag);
}
static void
mpi_get_nvmd_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct fw_control_ex *fw_control_context;
struct get_nvm_data_resp *pPayload =
(struct get_nvm_data_resp *)(piomb + 4);
u32 tag = le32_to_cpu(pPayload->tag);
struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
u32 dlen_status = le32_to_cpu(pPayload->dlen_status);
u32 ir_tds_bn_dps_das_nvm =
le32_to_cpu(pPayload->ir_tda_bn_dps_das_nvm);
void *virt_addr = pm8001_ha->memoryMap.region[NVMD].virt_ptr;
fw_control_context = ccb->fw_control_context;
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Get nvm data complete!\n"));
if ((dlen_status & NVMD_STAT) != 0) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Get nvm data error!\n"));
complete(pm8001_ha->nvmd_completion);
return;
}
if (ir_tds_bn_dps_das_nvm & IPMode) {
/* indirect mode - IR bit set */
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("Get NVMD success, IR=1\n"));
if ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == TWI_DEVICE) {
if (ir_tds_bn_dps_das_nvm == 0x80a80200) {
memcpy(pm8001_ha->sas_addr,
((u8 *)virt_addr + 4),
SAS_ADDR_SIZE);
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("Get SAS address"
" from VPD successfully!\n"));
}
} else if (((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == C_SEEPROM)
|| ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == VPD_FLASH) ||
((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == EXPAN_ROM)) {
;
} else if (((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == AAP1_RDUMP)
|| ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == IOP_RDUMP)) {
;
} else {
/* Should not be happened*/
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("(IR=1)Wrong Device type 0x%x\n",
ir_tds_bn_dps_das_nvm));
}
} else /* direct mode */{
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("Get NVMD success, IR=0, dataLen=%d\n",
(dlen_status & NVMD_LEN) >> 24));
}
memcpy(fw_control_context->usrAddr,
pm8001_ha->memoryMap.region[NVMD].virt_ptr,
fw_control_context->len);
complete(pm8001_ha->nvmd_completion);
ccb->task = NULL;
ccb->ccb_tag = 0xFFFFFFFF;
pm8001_ccb_free(pm8001_ha, tag);
}
static int mpi_local_phy_ctl(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct local_phy_ctl_resp *pPayload =
(struct local_phy_ctl_resp *)(piomb + 4);
u32 status = le32_to_cpu(pPayload->status);
u32 phy_id = le32_to_cpu(pPayload->phyop_phyid) & ID_BITS;
u32 phy_op = le32_to_cpu(pPayload->phyop_phyid) & OP_BITS;
if (status != 0) {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("%x phy execute %x phy op failed!\n",
phy_id, phy_op));
} else
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("%x phy execute %x phy op success!\n",
phy_id, phy_op));
return 0;
}
/**
* pm8001_bytes_dmaed - one of the interface function communication with libsas
* @pm8001_ha: our hba card information
* @i: which phy that received the event.
*
* when HBA driver received the identify done event or initiate FIS received
* event(for SATA), it will invoke this function to notify the sas layer that
* the sas toplogy has formed, please discover the the whole sas domain,
* while receive a broadcast(change) primitive just tell the sas
* layer to discover the changed domain rather than the whole domain.
*/
static void pm8001_bytes_dmaed(struct pm8001_hba_info *pm8001_ha, int i)
{
struct pm8001_phy *phy = &pm8001_ha->phy[i];
struct asd_sas_phy *sas_phy = &phy->sas_phy;
struct sas_ha_struct *sas_ha;
if (!phy->phy_attached)
return;
sas_ha = pm8001_ha->sas;
if (sas_phy->phy) {
struct sas_phy *sphy = sas_phy->phy;
sphy->negotiated_linkrate = sas_phy->linkrate;
sphy->minimum_linkrate = phy->minimum_linkrate;
sphy->minimum_linkrate_hw = SAS_LINK_RATE_1_5_GBPS;
sphy->maximum_linkrate = phy->maximum_linkrate;
sphy->maximum_linkrate_hw = phy->maximum_linkrate;
}
if (phy->phy_type & PORT_TYPE_SAS) {
struct sas_identify_frame *id;
id = (struct sas_identify_frame *)phy->frame_rcvd;
id->dev_type = phy->identify.device_type;
id->initiator_bits = SAS_PROTOCOL_ALL;
id->target_bits = phy->identify.target_port_protocols;
} else if (phy->phy_type & PORT_TYPE_SATA) {
/*Nothing*/
}
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("phy %d byte dmaded.\n", i));
sas_phy->frame_rcvd_size = phy->frame_rcvd_size;
pm8001_ha->sas->notify_port_event(sas_phy, PORTE_BYTES_DMAED);
}
/* Get the link rate speed */
static void get_lrate_mode(struct pm8001_phy *phy, u8 link_rate)
{
struct sas_phy *sas_phy = phy->sas_phy.phy;
switch (link_rate) {
case PHY_SPEED_60:
phy->sas_phy.linkrate = SAS_LINK_RATE_6_0_GBPS;
phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_6_0_GBPS;
break;
case PHY_SPEED_30:
phy->sas_phy.linkrate = SAS_LINK_RATE_3_0_GBPS;
phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_3_0_GBPS;
break;
case PHY_SPEED_15:
phy->sas_phy.linkrate = SAS_LINK_RATE_1_5_GBPS;
phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_1_5_GBPS;
break;
}
sas_phy->negotiated_linkrate = phy->sas_phy.linkrate;
sas_phy->maximum_linkrate_hw = SAS_LINK_RATE_6_0_GBPS;
sas_phy->minimum_linkrate_hw = SAS_LINK_RATE_1_5_GBPS;
sas_phy->maximum_linkrate = SAS_LINK_RATE_6_0_GBPS;
sas_phy->minimum_linkrate = SAS_LINK_RATE_1_5_GBPS;
}
/**
* asd_get_attached_sas_addr -- extract/generate attached SAS address
* @phy: pointer to asd_phy
* @sas_addr: pointer to buffer where the SAS address is to be written
*
* This function extracts the SAS address from an IDENTIFY frame
* received. If OOB is SATA, then a SAS address is generated from the
* HA tables.
*
* LOCKING: the frame_rcvd_lock needs to be held since this parses the frame
* buffer.
*/
static void pm8001_get_attached_sas_addr(struct pm8001_phy *phy,
u8 *sas_addr)
{
if (phy->sas_phy.frame_rcvd[0] == 0x34
&& phy->sas_phy.oob_mode == SATA_OOB_MODE) {
struct pm8001_hba_info *pm8001_ha = phy->sas_phy.ha->lldd_ha;
/* FIS device-to-host */
u64 addr = be64_to_cpu(*(__be64 *)pm8001_ha->sas_addr);
addr += phy->sas_phy.id;
*(__be64 *)sas_addr = cpu_to_be64(addr);
} else {
struct sas_identify_frame *idframe =
(void *) phy->sas_phy.frame_rcvd;
memcpy(sas_addr, idframe->sas_addr, SAS_ADDR_SIZE);
}
}
/**
* pm8001_hw_event_ack_req- For PM8001,some events need to acknowage to FW.
* @pm8001_ha: our hba card information
* @Qnum: the outbound queue message number.
* @SEA: source of event to ack
* @port_id: port id.
* @phyId: phy id.
* @param0: parameter 0.
* @param1: parameter 1.
*/
static void pm8001_hw_event_ack_req(struct pm8001_hba_info *pm8001_ha,
u32 Qnum, u32 SEA, u32 port_id, u32 phyId, u32 param0, u32 param1)
{
struct hw_event_ack_req payload;
u32 opc = OPC_INB_SAS_HW_EVENT_ACK;
struct inbound_queue_table *circularQ;
memset((u8 *)&payload, 0, sizeof(payload));
circularQ = &pm8001_ha->inbnd_q_tbl[Qnum];
payload.tag = cpu_to_le32(1);
payload.sea_phyid_portid = cpu_to_le32(((SEA & 0xFFFF) << 8) |
((phyId & 0x0F) << 4) | (port_id & 0x0F));
payload.param0 = cpu_to_le32(param0);
payload.param1 = cpu_to_le32(param1);
mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
}
static int pm8001_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha,
u32 phyId, u32 phy_op);
/**
* hw_event_sas_phy_up -FW tells me a SAS phy up event.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void
hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_evt_status_phyid_portid =
le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
u8 link_rate =
(u8)((lr_evt_status_phyid_portid & 0xF0000000) >> 28);
u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
u8 phy_id =
(u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate);
u8 portstate = (u8)(npip_portstate & 0x0000000F);
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
unsigned long flags;
u8 deviceType = pPayload->sas_identify.dev_type;
port->port_state = portstate;
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SAS_PHY_UP port id = %d, phy id = %d\n",
port_id, phy_id));
switch (deviceType) {
case SAS_PHY_UNUSED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("device type no device.\n"));
break;
case SAS_END_DEVICE:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("end device.\n"));
pm8001_chip_phy_ctl_req(pm8001_ha, phy_id,
PHY_NOTIFY_ENABLE_SPINUP);
port->port_attached = 1;
get_lrate_mode(phy, link_rate);
break;
case SAS_EDGE_EXPANDER_DEVICE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("expander device.\n"));
port->port_attached = 1;
get_lrate_mode(phy, link_rate);
break;
case SAS_FANOUT_EXPANDER_DEVICE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("fanout expander device.\n"));
port->port_attached = 1;
get_lrate_mode(phy, link_rate);
break;
default:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("unknown device type(%x)\n", deviceType));
break;
}
phy->phy_type |= PORT_TYPE_SAS;
phy->identify.device_type = deviceType;
phy->phy_attached = 1;
if (phy->identify.device_type == SAS_END_DEVICE)
phy->identify.target_port_protocols = SAS_PROTOCOL_SSP;
else if (phy->identify.device_type != SAS_PHY_UNUSED)
phy->identify.target_port_protocols = SAS_PROTOCOL_SMP;
phy->sas_phy.oob_mode = SAS_OOB_MODE;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE);
spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags);
memcpy(phy->frame_rcvd, &pPayload->sas_identify,
sizeof(struct sas_identify_frame)-4);
phy->frame_rcvd_size = sizeof(struct sas_identify_frame) - 4;
pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr);
spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags);
if (pm8001_ha->flags == PM8001F_RUN_TIME)
mdelay(200);/*delay a moment to wait disk to spinup*/
pm8001_bytes_dmaed(pm8001_ha, phy_id);
}
/**
* hw_event_sata_phy_up -FW tells me a SATA phy up event.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void
hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_evt_status_phyid_portid =
le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
u8 link_rate =
(u8)((lr_evt_status_phyid_portid & 0xF0000000) >> 28);
u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
u8 phy_id =
(u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate);
u8 portstate = (u8)(npip_portstate & 0x0000000F);
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
unsigned long flags;
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SATA_PHY_UP port id = %d,"
" phy id = %d\n", port_id, phy_id));
port->port_state = portstate;
port->port_attached = 1;
get_lrate_mode(phy, link_rate);
phy->phy_type |= PORT_TYPE_SATA;
phy->phy_attached = 1;
phy->sas_phy.oob_mode = SATA_OOB_MODE;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE);
spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags);
memcpy(phy->frame_rcvd, ((u8 *)&pPayload->sata_fis - 4),
sizeof(struct dev_to_host_fis));
phy->frame_rcvd_size = sizeof(struct dev_to_host_fis);
phy->identify.target_port_protocols = SAS_PROTOCOL_SATA;
phy->identify.device_type = SATA_DEV;
pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr);
spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags);
pm8001_bytes_dmaed(pm8001_ha, phy_id);
}
/**
* hw_event_phy_down -we should notify the libsas the phy is down.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void
hw_event_phy_down(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_evt_status_phyid_portid =
le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
u8 phy_id =
(u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate);
u8 portstate = (u8)(npip_portstate & 0x0000000F);
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
port->port_state = portstate;
phy->phy_type = 0;
phy->identify.device_type = 0;
phy->phy_attached = 0;
memset(&phy->dev_sas_addr, 0, SAS_ADDR_SIZE);
switch (portstate) {
case PORT_VALID:
break;
case PORT_INVALID:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" PortInvalid portID %d\n", port_id));
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Last phy Down and port invalid\n"));
port->port_attached = 0;
pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
port_id, phy_id, 0, 0);
break;
case PORT_IN_RESET:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Port In Reset portID %d\n", port_id));
break;
case PORT_NOT_ESTABLISHED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" phy Down and PORT_NOT_ESTABLISHED\n"));
port->port_attached = 0;
break;
case PORT_LOSTCOMM:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" phy Down and PORT_LOSTCOMM\n"));
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Last phy Down and port invalid\n"));
port->port_attached = 0;
pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
port_id, phy_id, 0, 0);
break;
default:
port->port_attached = 0;
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" phy Down and(default) = %x\n",
portstate));
break;
}
}
/**
* mpi_reg_resp -process register device ID response.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*
* when sas layer find a device it will notify LLDD, then the driver register
* the domain device to FW, this event is the return device ID which the FW
* has assigned, from now,inter-communication with FW is no longer using the
* SAS address, use device ID which FW assigned.
*/
static int mpi_reg_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
u32 status;
u32 device_id;
u32 htag;
struct pm8001_ccb_info *ccb;
struct pm8001_device *pm8001_dev;
struct dev_reg_resp *registerRespPayload =
(struct dev_reg_resp *)(piomb + 4);
htag = le32_to_cpu(registerRespPayload->tag);
ccb = &pm8001_ha->ccb_info[htag];
pm8001_dev = ccb->device;
status = le32_to_cpu(registerRespPayload->status);
device_id = le32_to_cpu(registerRespPayload->device_id);
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" register device is status = %d\n", status));
switch (status) {
case DEVREG_SUCCESS:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("DEVREG_SUCCESS\n"));
pm8001_dev->device_id = device_id;
break;
case DEVREG_FAILURE_OUT_OF_RESOURCE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_OUT_OF_RESOURCE\n"));
break;
case DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED\n"));
break;
case DEVREG_FAILURE_INVALID_PHY_ID:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_INVALID_PHY_ID\n"));
break;
case DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED\n"));
break;
case DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE\n"));
break;
case DEVREG_FAILURE_PORT_NOT_VALID_STATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_PORT_NOT_VALID_STATE\n"));
break;
case DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID\n"));
break;
default:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("DEVREG_FAILURE_DEVICE_TYPE_NOT_UNSORPORTED\n"));
break;
}
complete(pm8001_dev->dcompletion);
ccb->task = NULL;
ccb->ccb_tag = 0xFFFFFFFF;
pm8001_ccb_free(pm8001_ha, htag);
return 0;
}
static int mpi_dereg_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
u32 status;
u32 device_id;
struct dev_reg_resp *registerRespPayload =
(struct dev_reg_resp *)(piomb + 4);
status = le32_to_cpu(registerRespPayload->status);
device_id = le32_to_cpu(registerRespPayload->device_id);
if (status != 0)
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" deregister device failed ,status = %x"
", device_id = %x\n", status, device_id));
return 0;
}
static int
mpi_fw_flash_update_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
u32 status;
struct fw_control_ex fw_control_context;
struct fw_flash_Update_resp *ppayload =
(struct fw_flash_Update_resp *)(piomb + 4);
u32 tag = le32_to_cpu(ppayload->tag);
struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag];
status = le32_to_cpu(ppayload->status);
memcpy(&fw_control_context,
ccb->fw_control_context,
sizeof(fw_control_context));
switch (status) {
case FLASH_UPDATE_COMPLETE_PENDING_REBOOT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_COMPLETE_PENDING_REBOOT\n"));
break;
case FLASH_UPDATE_IN_PROGRESS:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_IN_PROGRESS\n"));
break;
case FLASH_UPDATE_HDR_ERR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_HDR_ERR\n"));
break;
case FLASH_UPDATE_OFFSET_ERR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_OFFSET_ERR\n"));
break;
case FLASH_UPDATE_CRC_ERR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_CRC_ERR\n"));
break;
case FLASH_UPDATE_LENGTH_ERR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_LENGTH_ERR\n"));
break;
case FLASH_UPDATE_HW_ERR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_HW_ERR\n"));
break;
case FLASH_UPDATE_DNLD_NOT_SUPPORTED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_DNLD_NOT_SUPPORTED\n"));
break;
case FLASH_UPDATE_DISABLED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(": FLASH_UPDATE_DISABLED\n"));
break;
default:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("No matched status = %d\n", status));
break;
}
ccb->fw_control_context->fw_control->retcode = status;
pci_free_consistent(pm8001_ha->pdev,
fw_control_context.len,
fw_control_context.virtAddr,
fw_control_context.phys_addr);
complete(pm8001_ha->nvmd_completion);
ccb->task = NULL;
ccb->ccb_tag = 0xFFFFFFFF;
pm8001_ccb_free(pm8001_ha, tag);
return 0;
}
static int
mpi_general_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
u32 status;
int i;
struct general_event_resp *pPayload =
(struct general_event_resp *)(piomb + 4);
status = le32_to_cpu(pPayload->status);
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" status = 0x%x\n", status));
for (i = 0; i < GENERAL_EVENT_PAYLOAD; i++)
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("inb_IOMB_payload[0x%x] 0x%x,\n", i,
pPayload->inb_IOMB_payload[i]));
return 0;
}
static int
mpi_task_abort_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct sas_task *t;
struct pm8001_ccb_info *ccb;
unsigned long flags;
u32 status ;
u32 tag, scp;
struct task_status_struct *ts;
struct task_abort_resp *pPayload =
(struct task_abort_resp *)(piomb + 4);
status = le32_to_cpu(pPayload->status);
tag = le32_to_cpu(pPayload->tag);
scp = le32_to_cpu(pPayload->scp);
ccb = &pm8001_ha->ccb_info[tag];
t = ccb->task;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk(" status = 0x%x\n", status));
if (t == NULL)
return -1;
ts = &t->task_status;
if (status != 0)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task abort failed status 0x%x ,"
"tag = 0x%x, scp= 0x%x\n", status, tag, scp));
switch (status) {
case IO_SUCCESS:
PM8001_EH_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
break;
case IO_NOT_VALID:
PM8001_EH_DBG(pm8001_ha, pm8001_printk("IO_NOT_VALID\n"));
ts->resp = TMF_RESP_FUNC_FAILED;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();
t->task_done(t);
return 0;
}
/**
* mpi_hw_event -The hw event has come.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_hw_event(struct pm8001_hba_info *pm8001_ha, void* piomb)
{
unsigned long flags;
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_evt_status_phyid_portid =
le32_to_cpu(pPayload->lr_evt_status_phyid_portid);
u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F);
u8 phy_id =
(u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4);
u16 eventType =
(u16)((lr_evt_status_phyid_portid & 0x00FFFF00) >> 8);
u8 status =
(u8)((lr_evt_status_phyid_portid & 0x0F000000) >> 24);
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
struct asd_sas_phy *sas_phy = sas_ha->sas_phy[phy_id];
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("outbound queue HW event & event type : "));
switch (eventType) {
case HW_EVENT_PHY_START_STATUS:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_START_STATUS"
" status = %x\n", status));
if (status == 0) {
phy->phy_state = 1;
if (pm8001_ha->flags == PM8001F_RUN_TIME)
complete(phy->enable_completion);
}
break;
case HW_EVENT_SAS_PHY_UP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_START_STATUS\n"));
hw_event_sas_phy_up(pm8001_ha, piomb);
break;
case HW_EVENT_SATA_PHY_UP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SATA_PHY_UP\n"));
hw_event_sata_phy_up(pm8001_ha, piomb);
break;
case HW_EVENT_PHY_STOP_STATUS:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_STOP_STATUS "
"status = %x\n", status));
if (status == 0)
phy->phy_state = 0;
break;
case HW_EVENT_SATA_SPINUP_HOLD:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SATA_SPINUP_HOLD\n"));
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_SPINUP_HOLD);
break;
case HW_EVENT_PHY_DOWN:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_DOWN\n"));
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_LOSS_OF_SIGNAL);
phy->phy_attached = 0;
phy->phy_state = 0;
hw_event_phy_down(pm8001_ha, piomb);
break;
case HW_EVENT_PORT_INVALID:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_INVALID\n"));
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
/* the broadcast change primitive received, tell the LIBSAS this event
to revalidate the sas domain*/
case HW_EVENT_BROADCAST_CHANGE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_BROADCAST_CHANGE\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_BROADCAST_CHANGE,
port_id, phy_id, 1, 0);
spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
sas_phy->sas_prim = HW_EVENT_BROADCAST_CHANGE;
spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
break;
case HW_EVENT_PHY_ERROR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_ERROR\n"));
sas_phy_disconnected(&phy->sas_phy);
phy->phy_attached = 0;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_ERROR);
break;
case HW_EVENT_BROADCAST_EXP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_BROADCAST_EXP\n"));
spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
sas_phy->sas_prim = HW_EVENT_BROADCAST_EXP;
spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
break;
case HW_EVENT_LINK_ERR_INVALID_DWORD:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_INVALID_DWORD\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_INVALID_DWORD, port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_LINK_ERR_DISPARITY_ERROR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_DISPARITY_ERROR\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_DISPARITY_ERROR,
port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_LINK_ERR_CODE_VIOLATION:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_CODE_VIOLATION\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_CODE_VIOLATION,
port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH,
port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_MALFUNCTION:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_MALFUNCTION\n"));
break;
case HW_EVENT_BROADCAST_SES:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_BROADCAST_SES\n"));
spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
sas_phy->sas_prim = HW_EVENT_BROADCAST_SES;
spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
break;
case HW_EVENT_INBOUND_CRC_ERROR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_INBOUND_CRC_ERROR\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_INBOUND_CRC_ERROR,
port_id, phy_id, 0, 0);
break;
case HW_EVENT_HARD_RESET_RECEIVED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_HARD_RESET_RECEIVED\n"));
sas_ha->notify_port_event(sas_phy, PORTE_HARD_RESET);
break;
case HW_EVENT_ID_FRAME_TIMEOUT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_ID_FRAME_TIMEOUT\n"));
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_LINK_ERR_PHY_RESET_FAILED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_PHY_RESET_FAILED\n"));
pm8001_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_PHY_RESET_FAILED,
port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_PORT_RESET_TIMER_TMO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RESET_TIMER_TMO\n"));
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_PORT_RECOVERY_TIMER_TMO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RECOVERY_TIMER_TMO\n"));
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_PORT_RECOVER:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RECOVER\n"));
break;
case HW_EVENT_PORT_RESET_COMPLETE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RESET_COMPLETE\n"));
break;
case EVENT_BROADCAST_ASYNCH_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("EVENT_BROADCAST_ASYNCH_EVENT\n"));
break;
default:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("Unknown event type = %x\n", eventType));
break;
}
return 0;
}
/**
* process_one_iomb - process one outbound Queue memory block
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void process_one_iomb(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
__le32 pHeader = *(__le32 *)piomb;
u8 opc = (u8)((le32_to_cpu(pHeader)) & 0xFFF);
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("process_one_iomb:"));
switch (opc) {
case OPC_OUB_ECHO:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("OPC_OUB_ECHO\n"));
break;
case OPC_OUB_HW_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_HW_EVENT\n"));
mpi_hw_event(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_COMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_COMP\n"));
mpi_ssp_completion(pm8001_ha, piomb);
break;
case OPC_OUB_SMP_COMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SMP_COMP\n"));
mpi_smp_completion(pm8001_ha, piomb);
break;
case OPC_OUB_LOCAL_PHY_CNTRL:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_LOCAL_PHY_CNTRL\n"));
mpi_local_phy_ctl(pm8001_ha, piomb);
break;
case OPC_OUB_DEV_REGIST:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEV_REGIST\n"));
mpi_reg_resp(pm8001_ha, piomb);
break;
case OPC_OUB_DEREG_DEV:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("unregister the device\n"));
mpi_dereg_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_DEV_HANDLE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_DEV_HANDLE\n"));
break;
case OPC_OUB_SATA_COMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SATA_COMP\n"));
mpi_sata_completion(pm8001_ha, piomb);
break;
case OPC_OUB_SATA_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SATA_EVENT\n"));
mpi_sata_event(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_EVENT\n"));
mpi_ssp_event(pm8001_ha, piomb);
break;
case OPC_OUB_DEV_HANDLE_ARRIV:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEV_HANDLE_ARRIV\n"));
/*This is for target*/
break;
case OPC_OUB_SSP_RECV_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_RECV_EVENT\n"));
/*This is for target*/
break;
case OPC_OUB_DEV_INFO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEV_INFO\n"));
break;
case OPC_OUB_FW_FLASH_UPDATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_FW_FLASH_UPDATE\n"));
mpi_fw_flash_update_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GPIO_RESPONSE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GPIO_RESPONSE\n"));
break;
case OPC_OUB_GPIO_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GPIO_EVENT\n"));
break;
case OPC_OUB_GENERAL_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GENERAL_EVENT\n"));
mpi_general_event(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_ABORT_RSP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_ABORT_RSP\n"));
mpi_task_abort_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SATA_ABORT_RSP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SATA_ABORT_RSP\n"));
mpi_task_abort_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SAS_DIAG_MODE_START_END:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_DIAG_MODE_START_END\n"));
break;
case OPC_OUB_SAS_DIAG_EXECUTE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_DIAG_EXECUTE\n"));
break;
case OPC_OUB_GET_TIME_STAMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_TIME_STAMP\n"));
break;
case OPC_OUB_SAS_HW_EVENT_ACK:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_HW_EVENT_ACK\n"));
break;
case OPC_OUB_PORT_CONTROL:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_PORT_CONTROL\n"));
break;
case OPC_OUB_SMP_ABORT_RSP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SMP_ABORT_RSP\n"));
mpi_task_abort_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_NVMD_DATA:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_NVMD_DATA\n"));
mpi_get_nvmd_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SET_NVMD_DATA:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SET_NVMD_DATA\n"));
mpi_set_nvmd_resp(pm8001_ha, piomb);
break;
case OPC_OUB_DEVICE_HANDLE_REMOVAL:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEVICE_HANDLE_REMOVAL\n"));
break;
case OPC_OUB_SET_DEVICE_STATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SET_DEVICE_STATE\n"));
mpi_set_dev_state_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_DEVICE_STATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_DEVICE_STATE\n"));
break;
case OPC_OUB_SET_DEV_INFO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SET_DEV_INFO\n"));
break;
case OPC_OUB_SAS_RE_INITIALIZE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_RE_INITIALIZE\n"));
break;
default:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("Unknown outbound Queue IOMB OPC = %x\n",
opc));
break;
}
}
static int process_oq(struct pm8001_hba_info *pm8001_ha)
{
struct outbound_queue_table *circularQ;
void *pMsg1 = NULL;
u8 uninitialized_var(bc);
u32 ret = MPI_IO_STATUS_FAIL;
unsigned long flags;
spin_lock_irqsave(&pm8001_ha->lock, flags);
circularQ = &pm8001_ha->outbnd_q_tbl[0];
do {
ret = mpi_msg_consume(pm8001_ha, circularQ, &pMsg1, &bc);
if (MPI_IO_STATUS_SUCCESS == ret) {
/* process the outbound message */
process_one_iomb(pm8001_ha, (void *)(pMsg1 - 4));
/* free the message from the outbound circular buffer */
mpi_msg_free_set(pm8001_ha, pMsg1, circularQ, bc);
}
if (MPI_IO_STATUS_BUSY == ret) {
/* Update the producer index from SPC */
circularQ->producer_index =
cpu_to_le32(pm8001_read_32(circularQ->pi_virt));
if (le32_to_cpu(circularQ->producer_index) ==
circularQ->consumer_idx)
/* OQ is empty */
break;
}
} while (1);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return ret;
}
/* PCI_DMA_... to our direction translation. */
static const u8 data_dir_flags[] = {
[PCI_DMA_BIDIRECTIONAL] = DATA_DIR_BYRECIPIENT,/* UNSPECIFIED */
[PCI_DMA_TODEVICE] = DATA_DIR_OUT,/* OUTBOUND */
[PCI_DMA_FROMDEVICE] = DATA_DIR_IN,/* INBOUND */
[PCI_DMA_NONE] = DATA_DIR_NONE,/* NO TRANSFER */
};
static void
pm8001_chip_make_sg(struct scatterlist *scatter, int nr, void *prd)
{
int i;
struct scatterlist *sg;
struct pm8001_prd *buf_prd = prd;
for_each_sg(scatter, sg, nr, i) {
buf_prd->addr = cpu_to_le64(sg_dma_address(sg));
buf_prd->im_len.len = cpu_to_le32(sg_dma_len(sg));
buf_prd->im_len.e = 0;
buf_prd++;
}
}
static void build_smp_cmd(u32 deviceID, __le32 hTag, struct smp_req *psmp_cmd)
{
psmp_cmd->tag = hTag;
psmp_cmd->device_id = cpu_to_le32(deviceID);
psmp_cmd->len_ip_ir = cpu_to_le32(1|(1 << 1));
}
/**
* pm8001_chip_smp_req - send a SMP task to FW
* @pm8001_ha: our hba card information.
* @ccb: the ccb information this request used.
*/
static int pm8001_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb)
{
int elem, rc;
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_dev = dev->lldd_dev;
struct scatterlist *sg_req, *sg_resp;
u32 req_len, resp_len;
struct smp_req smp_cmd;
u32 opc;
struct inbound_queue_table *circularQ;
memset(&smp_cmd, 0, sizeof(smp_cmd));
/*
* DMA-map SMP request, response buffers
*/
sg_req = &task->smp_task.smp_req;
elem = dma_map_sg(pm8001_ha->dev, sg_req, 1, PCI_DMA_TODEVICE);
if (!elem)
return -ENOMEM;
req_len = sg_dma_len(sg_req);
sg_resp = &task->smp_task.smp_resp;
elem = dma_map_sg(pm8001_ha->dev, sg_resp, 1, PCI_DMA_FROMDEVICE);
if (!elem) {
rc = -ENOMEM;
goto err_out;
}
resp_len = sg_dma_len(sg_resp);
/* must be in dwords */
if ((req_len & 0x3) || (resp_len & 0x3)) {
rc = -EINVAL;
goto err_out_2;
}
opc = OPC_INB_SMP_REQUEST;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
smp_cmd.tag = cpu_to_le32(ccb->ccb_tag);
smp_cmd.long_smp_req.long_req_addr =
cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req));
smp_cmd.long_smp_req.long_req_size =
cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-4);
smp_cmd.long_smp_req.long_resp_addr =
cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_resp));
smp_cmd.long_smp_req.long_resp_size =
cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_resp)-4);
build_smp_cmd(pm8001_dev->device_id, smp_cmd.tag, &smp_cmd);
mpi_build_cmd(pm8001_ha, circularQ, opc, (u32 *)&smp_cmd);
return 0;
err_out_2:
dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_resp, 1,
PCI_DMA_FROMDEVICE);
err_out:
dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_req, 1,
PCI_DMA_TODEVICE);
return rc;
}
/**
* pm8001_chip_ssp_io_req - send a SSP task to FW
* @pm8001_ha: our hba card information.
* @ccb: the ccb information this request used.
*/
static int pm8001_chip_ssp_io_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb)
{
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_dev = dev->lldd_dev;
struct ssp_ini_io_start_req ssp_cmd;
u32 tag = ccb->ccb_tag;
int ret;
u64 phys_addr;
struct inbound_queue_table *circularQ;
u32 opc = OPC_INB_SSPINIIOSTART;
memset(&ssp_cmd, 0, sizeof(ssp_cmd));
memcpy(ssp_cmd.ssp_iu.lun, task->ssp_task.LUN, 8);
ssp_cmd.dir_m_tlr =
cpu_to_le32(data_dir_flags[task->data_dir] << 8 | 0x0);/*0 for
SAS 1.1 compatible TLR*/
ssp_cmd.data_len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.device_id = cpu_to_le32(pm8001_dev->device_id);
ssp_cmd.tag = cpu_to_le32(tag);
if (task->ssp_task.enable_first_burst)
ssp_cmd.ssp_iu.efb_prio_attr |= 0x80;
ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_prio << 3);
ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_attr & 7);
memcpy(ssp_cmd.ssp_iu.cdb, task->ssp_task.cdb, 16);
circularQ = &pm8001_ha->inbnd_q_tbl[0];
/* fill in PRD (scatter/gather) table, if any */
if (task->num_scatter > 1) {
pm8001_chip_make_sg(task->scatter, ccb->n_elem, ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info, buf_prd[0]);
ssp_cmd.addr_low = cpu_to_le32(lower_32_bits(phys_addr));
ssp_cmd.addr_high = cpu_to_le32(upper_32_bits(phys_addr));
ssp_cmd.esgl = cpu_to_le32(1<<31);
} else if (task->num_scatter == 1) {
u64 dma_addr = sg_dma_address(task->scatter);
ssp_cmd.addr_low = cpu_to_le32(lower_32_bits(dma_addr));
ssp_cmd.addr_high = cpu_to_le32(upper_32_bits(dma_addr));
ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.esgl = 0;
} else if (task->num_scatter == 0) {
ssp_cmd.addr_low = 0;
ssp_cmd.addr_high = 0;
ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.esgl = 0;
}
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &ssp_cmd);
return ret;
}
static int pm8001_chip_sata_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb)
{
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_ha_dev = dev->lldd_dev;
u32 tag = ccb->ccb_tag;
int ret;
struct sata_start_req sata_cmd;
u32 hdr_tag, ncg_tag = 0;
u64 phys_addr;
u32 ATAP = 0x0;
u32 dir;
struct inbound_queue_table *circularQ;
u32 opc = OPC_INB_SATA_HOST_OPSTART;
memset(&sata_cmd, 0, sizeof(sata_cmd));
circularQ = &pm8001_ha->inbnd_q_tbl[0];
if (task->data_dir == PCI_DMA_NONE) {
ATAP = 0x04; /* no data*/
PM8001_IO_DBG(pm8001_ha, pm8001_printk("no data\n"));
} else if (likely(!task->ata_task.device_control_reg_update)) {
if (task->ata_task.dma_xfer) {
ATAP = 0x06; /* DMA */
PM8001_IO_DBG(pm8001_ha, pm8001_printk("DMA\n"));
} else {
ATAP = 0x05; /* PIO*/
PM8001_IO_DBG(pm8001_ha, pm8001_printk("PIO\n"));
}
if (task->ata_task.use_ncq &&
dev->sata_dev.command_set != ATAPI_COMMAND_SET) {
ATAP = 0x07; /* FPDMA */
PM8001_IO_DBG(pm8001_ha, pm8001_printk("FPDMA\n"));
}
}
if (task->ata_task.use_ncq && pm8001_get_ncq_tag(task, &hdr_tag))
ncg_tag = hdr_tag;
dir = data_dir_flags[task->data_dir] << 8;
sata_cmd.tag = cpu_to_le32(tag);
sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
sata_cmd.data_len = cpu_to_le32(task->total_xfer_len);
sata_cmd.ncqtag_atap_dir_m =
cpu_to_le32(((ncg_tag & 0xff)<<16)|((ATAP & 0x3f) << 10) | dir);
sata_cmd.sata_fis = task->ata_task.fis;
if (likely(!task->ata_task.device_control_reg_update))
sata_cmd.sata_fis.flags |= 0x80;/* C=1: update ATA cmd reg */
sata_cmd.sata_fis.flags &= 0xF0;/* PM_PORT field shall be 0 */
/* fill in PRD (scatter/gather) table, if any */
if (task->num_scatter > 1) {
pm8001_chip_make_sg(task->scatter, ccb->n_elem, ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info, buf_prd[0]);
sata_cmd.addr_low = lower_32_bits(phys_addr);
sata_cmd.addr_high = upper_32_bits(phys_addr);
sata_cmd.esgl = cpu_to_le32(1 << 31);
} else if (task->num_scatter == 1) {
u64 dma_addr = sg_dma_address(task->scatter);
sata_cmd.addr_low = lower_32_bits(dma_addr);
sata_cmd.addr_high = upper_32_bits(dma_addr);
sata_cmd.len = cpu_to_le32(task->total_xfer_len);
sata_cmd.esgl = 0;
} else if (task->num_scatter == 0) {
sata_cmd.addr_low = 0;
sata_cmd.addr_high = 0;
sata_cmd.len = cpu_to_le32(task->total_xfer_len);
sata_cmd.esgl = 0;
}
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd);
return ret;
}
/**
* pm8001_chip_phy_start_req - start phy via PHY_START COMMAND
* @pm8001_ha: our hba card information.
* @num: the inbound queue number
* @phy_id: the phy id which we wanted to start up.
*/
static int
pm8001_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id)
{
struct phy_start_req payload;
struct inbound_queue_table *circularQ;
int ret;
u32 tag = 0x01;
u32 opcode = OPC_INB_PHYSTART;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
payload.tag = cpu_to_le32(tag);
/*
** [0:7] PHY Identifier
** [8:11] link rate 1.5G, 3G, 6G
** [12:13] link mode 01b SAS mode; 10b SATA mode; 11b both
** [14] 0b disable spin up hold; 1b enable spin up hold
*/
payload.ase_sh_lm_slr_phyid = cpu_to_le32(SPINHOLD_DISABLE |
LINKMODE_AUTO | LINKRATE_15 |
LINKRATE_30 | LINKRATE_60 | phy_id);
payload.sas_identify.dev_type = SAS_END_DEV;
payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
memcpy(payload.sas_identify.sas_addr,
pm8001_ha->sas_addr, SAS_ADDR_SIZE);
payload.sas_identify.phy_id = phy_id;
ret = mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload);
return ret;
}
/**
* pm8001_chip_phy_stop_req - start phy via PHY_STOP COMMAND
* @pm8001_ha: our hba card information.
* @num: the inbound queue number
* @phy_id: the phy id which we wanted to start up.
*/
static int pm8001_chip_phy_stop_req(struct pm8001_hba_info *pm8001_ha,
u8 phy_id)
{
struct phy_stop_req payload;
struct inbound_queue_table *circularQ;
int ret;
u32 tag = 0x01;
u32 opcode = OPC_INB_PHYSTOP;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
payload.tag = cpu_to_le32(tag);
payload.phy_id = cpu_to_le32(phy_id);
ret = mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload);
return ret;
}
/**
* see comments on mpi_reg_resp.
*/
static int pm8001_chip_reg_dev_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_device *pm8001_dev, u32 flag)
{
struct reg_dev_req payload;
u32 opc;
u32 stp_sspsmp_sata = 0x4;
struct inbound_queue_table *circularQ;
u32 linkrate, phy_id;
int rc, tag = 0xdeadbeef;
struct pm8001_ccb_info *ccb;
u8 retryFlag = 0x1;
u16 firstBurstSize = 0;
u16 ITNT = 2000;
struct domain_device *dev = pm8001_dev->sas_device;
struct domain_device *parent_dev = dev->parent;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return rc;
ccb = &pm8001_ha->ccb_info[tag];
ccb->device = pm8001_dev;
ccb->ccb_tag = tag;
payload.tag = cpu_to_le32(tag);
if (flag == 1)
stp_sspsmp_sata = 0x02; /*direct attached sata */
else {
if (pm8001_dev->dev_type == SATA_DEV)
stp_sspsmp_sata = 0x00; /* stp*/
else if (pm8001_dev->dev_type == SAS_END_DEV ||
pm8001_dev->dev_type == EDGE_DEV ||
pm8001_dev->dev_type == FANOUT_DEV)
stp_sspsmp_sata = 0x01; /*ssp or smp*/
}
if (parent_dev && DEV_IS_EXPANDER(parent_dev->dev_type))
phy_id = parent_dev->ex_dev.ex_phy->phy_id;
else
phy_id = pm8001_dev->attached_phy;
opc = OPC_INB_REG_DEV;
linkrate = (pm8001_dev->sas_device->linkrate < dev->port->linkrate) ?
pm8001_dev->sas_device->linkrate : dev->port->linkrate;
payload.phyid_portid =
cpu_to_le32(((pm8001_dev->sas_device->port->id) & 0x0F) |
((phy_id & 0x0F) << 4));
payload.dtype_dlr_retry = cpu_to_le32((retryFlag & 0x01) |
((linkrate & 0x0F) * 0x1000000) |
((stp_sspsmp_sata & 0x03) * 0x10000000));
payload.firstburstsize_ITNexustimeout =
cpu_to_le32(ITNT | (firstBurstSize * 0x10000));
memcpy(payload.sas_addr, pm8001_dev->sas_device->sas_addr,
SAS_ADDR_SIZE);
rc = mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
return rc;
}
/**
* see comments on mpi_reg_resp.
*/
static int pm8001_chip_dereg_dev_req(struct pm8001_hba_info *pm8001_ha,
u32 device_id)
{
struct dereg_dev_req payload;
u32 opc = OPC_INB_DEREG_DEV_HANDLE;
int ret;
struct inbound_queue_table *circularQ;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
payload.tag = cpu_to_le32(1);
payload.device_id = cpu_to_le32(device_id);
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("unregister device device_id = %d\n", device_id));
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
return ret;
}
/**
* pm8001_chip_phy_ctl_req - support the local phy operation
* @pm8001_ha: our hba card information.
* @num: the inbound queue number
* @phy_id: the phy id which we wanted to operate
* @phy_op:
*/
static int pm8001_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha,
u32 phyId, u32 phy_op)
{
struct local_phy_ctl_req payload;
struct inbound_queue_table *circularQ;
int ret;
u32 opc = OPC_INB_LOCAL_PHY_CONTROL;
memset(&payload, 0, sizeof(payload));
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(1);
payload.phyop_phyid =
cpu_to_le32(((phy_op & 0xff) << 8) | (phyId & 0x0F));
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
return ret;
}
static u32 pm8001_chip_is_our_interupt(struct pm8001_hba_info *pm8001_ha)
{
u32 value;
#ifdef PM8001_USE_MSIX
return 1;
#endif
value = pm8001_cr32(pm8001_ha, 0, MSGU_ODR);
if (value)
return 1;
return 0;
}
/**
* pm8001_chip_isr - PM8001 isr handler.
* @pm8001_ha: our hba card information.
* @irq: irq number.
* @stat: stat.
*/
static irqreturn_t
pm8001_chip_isr(struct pm8001_hba_info *pm8001_ha)
{
pm8001_chip_interrupt_disable(pm8001_ha);
process_oq(pm8001_ha);
pm8001_chip_interrupt_enable(pm8001_ha);
return IRQ_HANDLED;
}
static int send_task_abort(struct pm8001_hba_info *pm8001_ha, u32 opc,
u32 dev_id, u8 flag, u32 task_tag, u32 cmd_tag)
{
struct task_abort_req task_abort;
struct inbound_queue_table *circularQ;
int ret;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&task_abort, 0, sizeof(task_abort));
if (ABORT_SINGLE == (flag & ABORT_MASK)) {
task_abort.abort_all = 0;
task_abort.device_id = cpu_to_le32(dev_id);
task_abort.tag_to_abort = cpu_to_le32(task_tag);
task_abort.tag = cpu_to_le32(cmd_tag);
} else if (ABORT_ALL == (flag & ABORT_MASK)) {
task_abort.abort_all = cpu_to_le32(1);
task_abort.device_id = cpu_to_le32(dev_id);
task_abort.tag = cpu_to_le32(cmd_tag);
}
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort);
return ret;
}
/**
* pm8001_chip_abort_task - SAS abort task when error or exception happened.
* @task: the task we wanted to aborted.
* @flag: the abort flag.
*/
static int pm8001_chip_abort_task(struct pm8001_hba_info *pm8001_ha,
struct pm8001_device *pm8001_dev, u8 flag, u32 task_tag, u32 cmd_tag)
{
u32 opc, device_id;
int rc = TMF_RESP_FUNC_FAILED;
PM8001_EH_DBG(pm8001_ha, pm8001_printk("cmd_tag = %x, abort task tag"
" = %x", cmd_tag, task_tag));
if (pm8001_dev->dev_type == SAS_END_DEV)
opc = OPC_INB_SSP_ABORT;
else if (pm8001_dev->dev_type == SATA_DEV)
opc = OPC_INB_SATA_ABORT;
else
opc = OPC_INB_SMP_ABORT;/* SMP */
device_id = pm8001_dev->device_id;
rc = send_task_abort(pm8001_ha, opc, device_id, flag,
task_tag, cmd_tag);
if (rc != TMF_RESP_FUNC_COMPLETE)
PM8001_EH_DBG(pm8001_ha, pm8001_printk("rc= %d\n", rc));
return rc;
}
/**
* pm8001_chip_ssp_tm_req - built the task management command.
* @pm8001_ha: our hba card information.
* @ccb: the ccb information.
* @tmf: task management function.
*/
static int pm8001_chip_ssp_tm_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb, struct pm8001_tmf_task *tmf)
{
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_dev = dev->lldd_dev;
u32 opc = OPC_INB_SSPINITMSTART;
struct inbound_queue_table *circularQ;
struct ssp_ini_tm_start_req sspTMCmd;
int ret;
memset(&sspTMCmd, 0, sizeof(sspTMCmd));
sspTMCmd.device_id = cpu_to_le32(pm8001_dev->device_id);
sspTMCmd.relate_tag = cpu_to_le32(tmf->tag_of_task_to_be_managed);
sspTMCmd.tmf = cpu_to_le32(tmf->tmf);
memcpy(sspTMCmd.lun, task->ssp_task.LUN, 8);
sspTMCmd.tag = cpu_to_le32(ccb->ccb_tag);
circularQ = &pm8001_ha->inbnd_q_tbl[0];
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &sspTMCmd);
return ret;
}
static int pm8001_chip_get_nvmd_req(struct pm8001_hba_info *pm8001_ha,
void *payload)
{
u32 opc = OPC_INB_GET_NVMD_DATA;
u32 nvmd_type;
int rc;
u32 tag;
struct pm8001_ccb_info *ccb;
struct inbound_queue_table *circularQ;
struct get_nvm_data_req nvmd_req;
struct fw_control_ex *fw_control_context;
struct pm8001_ioctl_payload *ioctl_payload = payload;
nvmd_type = ioctl_payload->minor_function;
fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL);
if (!fw_control_context)
return -ENOMEM;
fw_control_context->usrAddr = (u8 *)&ioctl_payload->func_specific[0];
fw_control_context->len = ioctl_payload->length;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&nvmd_req, 0, sizeof(nvmd_req));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc) {
kfree(fw_control_context);
return rc;
}
ccb = &pm8001_ha->ccb_info[tag];
ccb->ccb_tag = tag;
ccb->fw_control_context = fw_control_context;
nvmd_req.tag = cpu_to_le32(tag);
switch (nvmd_type) {
case TWI_DEVICE: {
u32 twi_addr, twi_page_size;
twi_addr = 0xa8;
twi_page_size = 2;
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | twi_addr << 16 |
twi_page_size << 8 | TWI_DEVICE);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
}
case C_SEEPROM: {
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | C_SEEPROM);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
}
case VPD_FLASH: {
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | VPD_FLASH);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
}
case EXPAN_ROM: {
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | EXPAN_ROM);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
}
default:
break;
}
rc = mpi_build_cmd(pm8001_ha, circularQ, opc, &nvmd_req);
return rc;
}
static int pm8001_chip_set_nvmd_req(struct pm8001_hba_info *pm8001_ha,
void *payload)
{
u32 opc = OPC_INB_SET_NVMD_DATA;
u32 nvmd_type;
int rc;
u32 tag;
struct pm8001_ccb_info *ccb;
struct inbound_queue_table *circularQ;
struct set_nvm_data_req nvmd_req;
struct fw_control_ex *fw_control_context;
struct pm8001_ioctl_payload *ioctl_payload = payload;
nvmd_type = ioctl_payload->minor_function;
fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL);
if (!fw_control_context)
return -ENOMEM;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memcpy(pm8001_ha->memoryMap.region[NVMD].virt_ptr,
ioctl_payload->func_specific,
ioctl_payload->length);
memset(&nvmd_req, 0, sizeof(nvmd_req));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc) {
kfree(fw_control_context);
return rc;
}
ccb = &pm8001_ha->ccb_info[tag];
ccb->fw_control_context = fw_control_context;
ccb->ccb_tag = tag;
nvmd_req.tag = cpu_to_le32(tag);
switch (nvmd_type) {
case TWI_DEVICE: {
u32 twi_addr, twi_page_size;
twi_addr = 0xa8;
twi_page_size = 2;
nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | twi_addr << 16 |
twi_page_size << 8 | TWI_DEVICE);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
}
case C_SEEPROM:
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | C_SEEPROM);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
case VPD_FLASH:
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | VPD_FLASH);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
case EXPAN_ROM:
nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | EXPAN_ROM);
nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length);
nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98);
nvmd_req.resp_addr_hi =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi);
nvmd_req.resp_addr_lo =
cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo);
break;
default:
break;
}
rc = mpi_build_cmd(pm8001_ha, circularQ, opc, &nvmd_req);
return rc;
}
/**
* pm8001_chip_fw_flash_update_build - support the firmware update operation
* @pm8001_ha: our hba card information.
* @fw_flash_updata_info: firmware flash update param
*/
static int
pm8001_chip_fw_flash_update_build(struct pm8001_hba_info *pm8001_ha,
void *fw_flash_updata_info, u32 tag)
{
struct fw_flash_Update_req payload;
struct fw_flash_updata_info *info;
struct inbound_queue_table *circularQ;
int ret;
u32 opc = OPC_INB_FW_FLASH_UPDATE;
memset(&payload, 0, sizeof(struct fw_flash_Update_req));
circularQ = &pm8001_ha->inbnd_q_tbl[0];
info = fw_flash_updata_info;
payload.tag = cpu_to_le32(tag);
payload.cur_image_len = cpu_to_le32(info->cur_image_len);
payload.cur_image_offset = cpu_to_le32(info->cur_image_offset);
payload.total_image_len = cpu_to_le32(info->total_image_len);
payload.len = info->sgl.im_len.len ;
payload.sgl_addr_lo =
cpu_to_le32(lower_32_bits(le64_to_cpu(info->sgl.addr)));
payload.sgl_addr_hi =
cpu_to_le32(upper_32_bits(le64_to_cpu(info->sgl.addr)));
ret = mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
return ret;
}
static int
pm8001_chip_fw_flash_update_req(struct pm8001_hba_info *pm8001_ha,
void *payload)
{
struct fw_flash_updata_info flash_update_info;
struct fw_control_info *fw_control;
struct fw_control_ex *fw_control_context;
int rc;
u32 tag;
struct pm8001_ccb_info *ccb;
void *buffer = NULL;
dma_addr_t phys_addr;
u32 phys_addr_hi;
u32 phys_addr_lo;
struct pm8001_ioctl_payload *ioctl_payload = payload;
fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL);
if (!fw_control_context)
return -ENOMEM;
fw_control = (struct fw_control_info *)&ioctl_payload->func_specific[0];
if (fw_control->len != 0) {
if (pm8001_mem_alloc(pm8001_ha->pdev,
(void **)&buffer,
&phys_addr,
&phys_addr_hi,
&phys_addr_lo,
fw_control->len, 0) != 0) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Mem alloc failure\n"));
kfree(fw_control_context);
return -ENOMEM;
}
}
memcpy(buffer, fw_control->buffer, fw_control->len);
flash_update_info.sgl.addr = cpu_to_le64(phys_addr);
flash_update_info.sgl.im_len.len = cpu_to_le32(fw_control->len);
flash_update_info.sgl.im_len.e = 0;
flash_update_info.cur_image_offset = fw_control->offset;
flash_update_info.cur_image_len = fw_control->len;
flash_update_info.total_image_len = fw_control->size;
fw_control_context->fw_control = fw_control;
fw_control_context->virtAddr = buffer;
fw_control_context->len = fw_control->len;
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc) {
kfree(fw_control_context);
return rc;
}
ccb = &pm8001_ha->ccb_info[tag];
ccb->fw_control_context = fw_control_context;
ccb->ccb_tag = tag;
rc = pm8001_chip_fw_flash_update_build(pm8001_ha, &flash_update_info,
tag);
return rc;
}
static int
pm8001_chip_set_dev_state_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_device *pm8001_dev, u32 state)
{
struct set_dev_state_req payload;
struct inbound_queue_table *circularQ;
struct pm8001_ccb_info *ccb;
int rc;
u32 tag;
u32 opc = OPC_INB_SET_DEVICE_STATE;
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return -1;
ccb = &pm8001_ha->ccb_info[tag];
ccb->ccb_tag = tag;
ccb->device = pm8001_dev;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
payload.device_id = cpu_to_le32(pm8001_dev->device_id);
payload.nds = cpu_to_le32(state);
rc = mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
return rc;
}
static int
pm8001_chip_sas_re_initialization(struct pm8001_hba_info *pm8001_ha)
{
struct sas_re_initialization_req payload;
struct inbound_queue_table *circularQ;
struct pm8001_ccb_info *ccb;
int rc;
u32 tag;
u32 opc = OPC_INB_SAS_RE_INITIALIZE;
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return -1;
ccb = &pm8001_ha->ccb_info[tag];
ccb->ccb_tag = tag;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
payload.SSAHOLT = cpu_to_le32(0xd << 25);
payload.sata_hol_tmo = cpu_to_le32(80);
payload.open_reject_cmdretries_data_retries = cpu_to_le32(0xff00ff);
rc = mpi_build_cmd(pm8001_ha, circularQ, opc, &payload);
return rc;
}
const struct pm8001_dispatch pm8001_8001_dispatch = {
.name = "pmc8001",
.chip_init = pm8001_chip_init,
.chip_soft_rst = pm8001_chip_soft_rst,
.chip_rst = pm8001_hw_chip_rst,
.chip_iounmap = pm8001_chip_iounmap,
.isr = pm8001_chip_isr,
.is_our_interupt = pm8001_chip_is_our_interupt,
.isr_process_oq = process_oq,
.interrupt_enable = pm8001_chip_interrupt_enable,
.interrupt_disable = pm8001_chip_interrupt_disable,
.make_prd = pm8001_chip_make_sg,
.smp_req = pm8001_chip_smp_req,
.ssp_io_req = pm8001_chip_ssp_io_req,
.sata_req = pm8001_chip_sata_req,
.phy_start_req = pm8001_chip_phy_start_req,
.phy_stop_req = pm8001_chip_phy_stop_req,
.reg_dev_req = pm8001_chip_reg_dev_req,
.dereg_dev_req = pm8001_chip_dereg_dev_req,
.phy_ctl_req = pm8001_chip_phy_ctl_req,
.task_abort = pm8001_chip_abort_task,
.ssp_tm_req = pm8001_chip_ssp_tm_req,
.get_nvmd_req = pm8001_chip_get_nvmd_req,
.set_nvmd_req = pm8001_chip_set_nvmd_req,
.fw_flash_update_req = pm8001_chip_fw_flash_update_req,
.set_dev_state_req = pm8001_chip_set_dev_state_req,
.sas_re_init_req = pm8001_chip_sas_re_initialization,
};