linux/arch/arm/boot/dts/imx23-evk.dts
Shawn Guo 352d318cc9 ARM: dts: imx: use generic node name for fixed regulator
The device tree specification recommends that generic name should be
used for nodes.  So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-02-09 21:32:30 +08:00

160 lines
3.3 KiB
Plaintext

/*
* Copyright 2012 Freescale Semiconductor, Inc.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include "imx23.dtsi"
/ {
model = "Freescale i.MX23 Evaluation Kit";
compatible = "fsl,imx23-evk", "fsl,imx23";
memory {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
gpmi-nand@8000c000 {
pinctrl-names = "default";
pinctrl-0 = <&gpmi_pins_a &gpmi_pins_fixup>;
status = "okay";
};
ssp0: ssp@80010000 {
compatible = "fsl,imx23-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
bus-width = <4>;
wp-gpios = <&gpio1 30 0>;
vmmc-supply = <&reg_vddio_sd0>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX23_PAD_LCD_RESET__GPIO_1_18
MX23_PAD_PWM3__GPIO_1_29
MX23_PAD_PWM4__GPIO_1_30
MX23_PAD_SSP1_DETECT__SSP1_DETECT
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a>;
lcd-supply = <&reg_lcd_3v3>;
display = <&display>;
status = "okay";
display: display {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <9200000>;
hactive = <480>;
vactive = <272>;
hback-porch = <15>;
hfront-porch = <8>;
vback-porch = <12>;
vfront-porch = <4>;
hsync-len = <1>;
vsync-len = <1>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
fsl,lradc-touchscreen-wires = <4>;
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm2_pins_a>;
status = "okay";
};
auart0: serial@8006c000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_pins_a>;
status = "okay";
};
duart: serial@80070000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_vddio_sd0: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "vddio-sd0";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 29 0>;
};
reg_lcd_3v3: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "lcd-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 18 0>;
enable-active-high;
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 2 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
};
};