linux/arch/arm/boot/dts/vexpress-v2m.dtsi
Sudeep Holla 01980aa7b0 ARM: dts: vexpress: use list instead of tuple for mmci interrupts
Vexpress motherboard MMCI requires dedicated interrupts for CMD and PIO,
which obviously should be expressed as a list. Current form uses tuple
and it works fine since interrupt-cells equal to 1.

Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2019-01-22 13:46:18 +00:00

451 lines
11 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0
/*
* ARM Ltd. Versatile Express
*
* Motherboard Express uATX
* V2M-P1
*
* HBI-0190D
*
* Original memory map ("Legacy memory map" in the board's
* Technical Reference Manual)
*
* WARNING! The hardware described in this file is independent from the
* RS1 variant (vexpress-v2m-rs1.dtsi), but there is a strong
* correspondence between the two configurations.
*
* TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
* CHANGES TO vexpress-v2m-rs1.dtsi!
*/
/ {
smb@4000000 {
motherboard {
model = "V2M-P1";
arm,hbi = <0x190>;
arm,vexpress,site = <0>;
compatible = "arm,vexpress,v2m-p1", "simple-bus";
#address-cells = <2>; /* SMB chipselect number and offset */
#size-cells = <1>;
#interrupt-cells = <1>;
ranges;
flash@0,00000000 {
compatible = "arm,vexpress-flash", "cfi-flash";
reg = <0 0x00000000 0x04000000>,
<1 0x00000000 0x04000000>;
bank-width = <4>;
};
psram@2,00000000 {
compatible = "arm,vexpress-psram", "mtd-ram";
reg = <2 0x00000000 0x02000000>;
bank-width = <4>;
};
ethernet@3,02000000 {
compatible = "smsc,lan9118", "smsc,lan9115";
reg = <3 0x02000000 0x10000>;
interrupts = <15>;
phy-mode = "mii";
reg-io-width = <4>;
smsc,irq-active-high;
smsc,irq-push-pull;
vdd33a-supply = <&v2m_fixed_3v3>;
vddvario-supply = <&v2m_fixed_3v3>;
};
usb@3,03000000 {
compatible = "nxp,usb-isp1761";
reg = <3 0x03000000 0x20000>;
interrupts = <16>;
port1-otg;
};
iofpga@7,00000000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 7 0 0x20000>;
v2m_sysreg: sysreg@0 {
compatible = "arm,vexpress-sysreg";
reg = <0x00000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0x1000>;
v2m_led_gpios: gpio@8 {
compatible = "arm,vexpress-sysreg,sys_led";
reg = <0x008 4>;
gpio-controller;
#gpio-cells = <2>;
};
v2m_mmc_gpios: gpio@48 {
compatible = "arm,vexpress-sysreg,sys_mci";
reg = <0x048 4>;
gpio-controller;
#gpio-cells = <2>;
};
v2m_flash_gpios: gpio@4c {
compatible = "arm,vexpress-sysreg,sys_flash";
reg = <0x04c 4>;
gpio-controller;
#gpio-cells = <2>;
};
};
v2m_sysctl: sysctl@1000 {
compatible = "arm,sp810", "arm,primecell";
reg = <0x01000 0x1000>;
clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
clock-names = "refclk", "timclk", "apb_pclk";
#clock-cells = <1>;
clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>;
assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>;
};
/* PCI-E I2C bus */
v2m_i2c_pcie: i2c@2000 {
compatible = "arm,versatile-i2c";
reg = <0x02000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
pcie-switch@60 {
compatible = "idt,89hpes32h8";
reg = <0x60>;
};
};
aaci@4000 {
compatible = "arm,pl041", "arm,primecell";
reg = <0x04000 0x1000>;
interrupts = <11>;
clocks = <&smbclk>;
clock-names = "apb_pclk";
};
mmci@5000 {
compatible = "arm,pl180", "arm,primecell";
reg = <0x05000 0x1000>;
interrupts = <9>, <10>;
cd-gpios = <&v2m_mmc_gpios 0 0>;
wp-gpios = <&v2m_mmc_gpios 1 0>;
max-frequency = <12000000>;
vmmc-supply = <&v2m_fixed_3v3>;
clocks = <&v2m_clk24mhz>, <&smbclk>;
clock-names = "mclk", "apb_pclk";
};
kmi@6000 {
compatible = "arm,pl050", "arm,primecell";
reg = <0x06000 0x1000>;
interrupts = <12>;
clocks = <&v2m_clk24mhz>, <&smbclk>;
clock-names = "KMIREFCLK", "apb_pclk";
};
kmi@7000 {
compatible = "arm,pl050", "arm,primecell";
reg = <0x07000 0x1000>;
interrupts = <13>;
clocks = <&v2m_clk24mhz>, <&smbclk>;
clock-names = "KMIREFCLK", "apb_pclk";
};
v2m_serial0: uart@9000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x09000 0x1000>;
interrupts = <5>;
clocks = <&v2m_oscclk2>, <&smbclk>;
clock-names = "uartclk", "apb_pclk";
};
v2m_serial1: uart@a000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0a000 0x1000>;
interrupts = <6>;
clocks = <&v2m_oscclk2>, <&smbclk>;
clock-names = "uartclk", "apb_pclk";
};
v2m_serial2: uart@b000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0b000 0x1000>;
interrupts = <7>;
clocks = <&v2m_oscclk2>, <&smbclk>;
clock-names = "uartclk", "apb_pclk";
};
v2m_serial3: uart@c000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0c000 0x1000>;
interrupts = <8>;
clocks = <&v2m_oscclk2>, <&smbclk>;
clock-names = "uartclk", "apb_pclk";
};
wdt@f000 {
compatible = "arm,sp805", "arm,primecell";
reg = <0x0f000 0x1000>;
interrupts = <0>;
clocks = <&v2m_refclk32khz>, <&smbclk>;
clock-names = "wdogclk", "apb_pclk";
};
v2m_timer01: timer@11000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x11000 0x1000>;
interrupts = <2>;
clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>;
clock-names = "timclken1", "timclken2", "apb_pclk";
};
v2m_timer23: timer@12000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x12000 0x1000>;
interrupts = <3>;
clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>;
clock-names = "timclken1", "timclken2", "apb_pclk";
};
/* DVI I2C bus */
v2m_i2c_dvi: i2c@16000 {
compatible = "arm,versatile-i2c";
reg = <0x16000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
dvi-transmitter@39 {
compatible = "sil,sii9022-tpi", "sil,sii9022";
reg = <0x39>;
ports {
#address-cells = <1>;
#size-cells = <0>;
/*
* Both the core tile and the motherboard routes their output
* pads to this transmitter. The motherboard system controller
* can select one of them as input using a mux register in
* "arm,vexpress-muxfpga". The Vexpress with the CA9 core tile is
* the only platform with this specific set-up.
*/
port@0 {
reg = <0>;
dvi_bridge_in_ct: endpoint {
remote-endpoint = <&clcd_pads_ct>;
};
};
port@1 {
reg = <1>;
dvi_bridge_in_mb: endpoint {
remote-endpoint = <&clcd_pads_mb>;
};
};
};
};
dvi-transmitter@60 {
compatible = "sil,sii9022-cpi", "sil,sii9022";
reg = <0x60>;
};
};
rtc@17000 {
compatible = "arm,pl031", "arm,primecell";
reg = <0x17000 0x1000>;
interrupts = <4>;
clocks = <&smbclk>;
clock-names = "apb_pclk";
};
compact-flash@1a000 {
compatible = "arm,vexpress-cf", "ata-generic";
reg = <0x1a000 0x100
0x1a100 0xf00>;
reg-shift = <2>;
};
clcd@1f000 {
compatible = "arm,pl111", "arm,primecell";
reg = <0x1f000 0x1000>;
interrupt-names = "combined";
interrupts = <14>;
clocks = <&v2m_oscclk1>, <&smbclk>;
clock-names = "clcdclk", "apb_pclk";
/* 800x600 16bpp @36MHz works fine */
max-memory-bandwidth = <54000000>;
memory-region = <&vram>;
port {
clcd_pads_mb: endpoint {
remote-endpoint = <&dvi_bridge_in_mb>;
arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
};
};
};
};
v2m_fixed_3v3: fixed-regulator-0 {
compatible = "regulator-fixed";
regulator-name = "3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
v2m_clk24mhz: clk24mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
clock-output-names = "v2m:clk24mhz";
};
v2m_refclk1mhz: refclk1mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <1000000>;
clock-output-names = "v2m:refclk1mhz";
};
v2m_refclk32khz: refclk32khz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "v2m:refclk32khz";
};
leds {
compatible = "gpio-leds";
user1 {
label = "v2m:green:user1";
gpios = <&v2m_led_gpios 0 0>;
linux,default-trigger = "heartbeat";
};
user2 {
label = "v2m:green:user2";
gpios = <&v2m_led_gpios 1 0>;
linux,default-trigger = "mmc0";
};
user3 {
label = "v2m:green:user3";
gpios = <&v2m_led_gpios 2 0>;
linux,default-trigger = "cpu0";
};
user4 {
label = "v2m:green:user4";
gpios = <&v2m_led_gpios 3 0>;
linux,default-trigger = "cpu1";
};
user5 {
label = "v2m:green:user5";
gpios = <&v2m_led_gpios 4 0>;
linux,default-trigger = "cpu2";
};
user6 {
label = "v2m:green:user6";
gpios = <&v2m_led_gpios 5 0>;
linux,default-trigger = "cpu3";
};
user7 {
label = "v2m:green:user7";
gpios = <&v2m_led_gpios 6 0>;
linux,default-trigger = "cpu4";
};
user8 {
label = "v2m:green:user8";
gpios = <&v2m_led_gpios 7 0>;
linux,default-trigger = "cpu5";
};
};
mcc {
compatible = "arm,vexpress,config-bus";
arm,vexpress,config-bridge = <&v2m_sysreg>;
oscclk0 {
/* MCC static memory clock */
compatible = "arm,vexpress-osc";
arm,vexpress-sysreg,func = <1 0>;
freq-range = <25000000 60000000>;
#clock-cells = <0>;
clock-output-names = "v2m:oscclk0";
};
v2m_oscclk1: oscclk1 {
/* CLCD clock */
compatible = "arm,vexpress-osc";
arm,vexpress-sysreg,func = <1 1>;
freq-range = <23750000 65000000>;
#clock-cells = <0>;
clock-output-names = "v2m:oscclk1";
};
v2m_oscclk2: oscclk2 {
/* IO FPGA peripheral clock */
compatible = "arm,vexpress-osc";
arm,vexpress-sysreg,func = <1 2>;
freq-range = <24000000 24000000>;
#clock-cells = <0>;
clock-output-names = "v2m:oscclk2";
};
volt-vio {
/* Logic level voltage */
compatible = "arm,vexpress-volt";
arm,vexpress-sysreg,func = <2 0>;
regulator-name = "VIO";
regulator-always-on;
label = "VIO";
};
temp-mcc {
/* MCC internal operating temperature */
compatible = "arm,vexpress-temp";
arm,vexpress-sysreg,func = <4 0>;
label = "MCC";
};
reset {
compatible = "arm,vexpress-reset";
arm,vexpress-sysreg,func = <5 0>;
};
muxfpga {
compatible = "arm,vexpress-muxfpga";
arm,vexpress-sysreg,func = <7 0>;
};
shutdown {
compatible = "arm,vexpress-shutdown";
arm,vexpress-sysreg,func = <8 0>;
};
reboot {
compatible = "arm,vexpress-reboot";
arm,vexpress-sysreg,func = <9 0>;
};
dvimode {
compatible = "arm,vexpress-dvimode";
arm,vexpress-sysreg,func = <11 0>;
};
};
};
};
};