linux/arch/arm/mach-davinci/board-omapl138-hawk.c
Victor Rodriguez bb59b7fdc1 davinci: EMAC support for Omapl138-Hawkboard
This patch adds EMAC support for the Hawkboard-L138 system

Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-02-28 14:53:28 -08:00

106 lines
2.5 KiB
C

/*
* Hawkboard.org based on TI's OMAP-L138 Platform
*
* Initial code: Syed Mohammed Khasim
*
* Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of
* any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/mux.h>
#define HAWKBOARD_PHY_ID "0:07"
static short omapl138_hawk_mii_pins[] __initdata = {
DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
DA850_MDIO_D,
-1
};
static __init void omapl138_hawk_config_emac(void)
{
void __iomem *cfgchip3 = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
int ret;
u32 val;
struct davinci_soc_info *soc_info = &davinci_soc_info;
val = __raw_readl(cfgchip3);
val &= ~BIT(8);
ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins);
if (ret) {
pr_warning("%s: cpgmac/mii mux setup failed: %d\n",
__func__, ret);
return;
}
/* configure the CFGCHIP3 register for MII */
__raw_writel(val, cfgchip3);
pr_info("EMAC: MII PHY configured\n");
soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID;
ret = da8xx_register_emac();
if (ret)
pr_warning("%s: emac registration failed: %d\n",
__func__, ret);
}
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
};
static __init void omapl138_hawk_init(void)
{
int ret;
davinci_serial_init(&omapl138_hawk_uart_config);
omapl138_hawk_config_emac();
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
"watchdog registration failed: %d\n",
ret);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init omapl138_hawk_console_init(void)
{
if (!machine_is_omapl138_hawkboard())
return 0;
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(omapl138_hawk_console_init);
#endif
static void __init omapl138_hawk_map_io(void)
{
da850_init();
}
MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = omapl138_hawk_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
.init_machine = omapl138_hawk_init,
MACHINE_END