linux/arch/arm/mach-sa1100/assabet.c
Arnd Bergmann c6e9fbbf4c ARM: assabet: fix bogus warning in get_assabet_scr (again)
Russell fixed this bogus warning before in 2f3eca8b4f "Shut up gcc
warning in assabet.c", but apparently gcc has become smarter (or dumber)
since 2005, and the same warning came up again.

This uses the uninitialized_var() macro to convince gcc that the
variable is actually being initialized. 100 times in fact.

Without this patch, building assabet_defconfig results in:

arch/arm/mach-sa1100/assabet.c: In function 'fixup_assabet':
arch/arm/mach-sa1100/assabet.c:397:6: warning: 'scr' may be used uninitialized in this function [-Wuninitialized]
arch/arm/mach-sa1100/assabet.c:389:16: note: 'scr' was declared here

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
2012-10-09 17:27:01 +02:00

632 lines
15 KiB
C

/*
* linux/arch/arm/mach-sa1100/assabet.c
*
* Author: Nicolas Pitre
*
* This file contains all Assabet-specific tweaks.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/serial_core.h>
#include <linux/mfd/ucb1x00.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
#include <linux/mm.h>
#include <linux/leds.h>
#include <linux/slab.h>
#include <video/sa1100fb.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <asm/pgtable-hwdef.h>
#include <asm/pgtable.h>
#include <asm/tlbflush.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/irda.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
#include <mach/assabet.h>
#include <linux/platform_data/mfd-mcp-sa11x0.h>
#include <mach/irqs.h>
#include "generic.h"
#define ASSABET_BCR_DB1110 \
(ASSABET_BCR_SPK_OFF | \
ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
ASSABET_BCR_IRDA_MD0)
#define ASSABET_BCR_DB1111 \
(ASSABET_BCR_SPK_OFF | \
ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \
ASSABET_BCR_IRDA_MD0 | ASSABET_BCR_CF_RST)
unsigned long SCR_value = ASSABET_SCR_INIT;
EXPORT_SYMBOL(SCR_value);
static unsigned long BCR_value = ASSABET_BCR_DB1110;
void ASSABET_BCR_frob(unsigned int mask, unsigned int val)
{
unsigned long flags;
local_irq_save(flags);
BCR_value = (BCR_value & ~mask) | val;
ASSABET_BCR = BCR_value;
local_irq_restore(flags);
}
EXPORT_SYMBOL(ASSABET_BCR_frob);
static void assabet_ucb1x00_reset(enum ucb1x00_reset state)
{
if (state == UCB_RST_PROBE)
ASSABET_BCR_set(ASSABET_BCR_CODEC_RST);
}
/*
* Assabet flash support code.
*/
#ifdef ASSABET_REV_4
/*
* Phase 4 Assabet has two 28F160B3 flash parts in bank 0:
*/
static struct mtd_partition assabet_partitions[] = {
{
.name = "bootloader",
.size = 0x00020000,
.offset = 0,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "bootloader params",
.size = 0x00020000,
.offset = MTDPART_OFS_APPEND,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "jffs",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_APPEND,
}
};
#else
/*
* Phase 5 Assabet has two 28F128J3A flash parts in bank 0:
*/
static struct mtd_partition assabet_partitions[] = {
{
.name = "bootloader",
.size = 0x00040000,
.offset = 0,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "bootloader params",
.size = 0x00040000,
.offset = MTDPART_OFS_APPEND,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "jffs",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_APPEND,
}
};
#endif
static struct flash_platform_data assabet_flash_data = {
.map_name = "cfi_probe",
.parts = assabet_partitions,
.nr_parts = ARRAY_SIZE(assabet_partitions),
};
static struct resource assabet_flash_resources[] = {
DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M),
DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M),
};
/*
* Assabet IrDA support code.
*/
static int assabet_irda_set_power(struct device *dev, unsigned int state)
{
static unsigned int bcr_state[4] = {
ASSABET_BCR_IRDA_MD0,
ASSABET_BCR_IRDA_MD1|ASSABET_BCR_IRDA_MD0,
ASSABET_BCR_IRDA_MD1,
0
};
if (state < 4) {
state = bcr_state[state];
ASSABET_BCR_clear(state ^ (ASSABET_BCR_IRDA_MD1|
ASSABET_BCR_IRDA_MD0));
ASSABET_BCR_set(state);
}
return 0;
}
static void assabet_irda_set_speed(struct device *dev, unsigned int speed)
{
if (speed < 4000000)
ASSABET_BCR_clear(ASSABET_BCR_IRDA_FSEL);
else
ASSABET_BCR_set(ASSABET_BCR_IRDA_FSEL);
}
static struct irda_platform_data assabet_irda_data = {
.set_power = assabet_irda_set_power,
.set_speed = assabet_irda_set_speed,
};
static struct ucb1x00_plat_data assabet_ucb1x00_data = {
.reset = assabet_ucb1x00_reset,
.gpio_base = -1,
};
static struct mcp_plat_data assabet_mcp_data = {
.mccr0 = MCCR0_ADM,
.sclk_rate = 11981000,
.codec_pdata = &assabet_ucb1x00_data,
};
static void assabet_lcd_set_visual(u32 visual)
{
u_int is_true_color = visual == FB_VISUAL_TRUECOLOR;
if (machine_is_assabet()) {
#if 1 // phase 4 or newer Assabet's
if (is_true_color)
ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
else
ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
#else
// older Assabet's
if (is_true_color)
ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
else
ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
#endif
}
}
#ifndef ASSABET_PAL_VIDEO
static void assabet_lcd_backlight_power(int on)
{
if (on)
ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
else
ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
}
/*
* Turn on/off the backlight. When turning the backlight on, we wait
* 500us after turning it on so we don't cause the supplies to droop
* when we enable the LCD controller (and cause a hard reset.)
*/
static void assabet_lcd_power(int on)
{
if (on) {
ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
udelay(500);
} else
ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
}
/*
* The assabet uses a sharp LQ039Q2DS54 LCD module. It is actually
* takes an RGB666 signal, but we provide it with an RGB565 signal
* instead (def_rgb_16).
*/
static struct sa1100fb_mach_info lq039q2ds54_info = {
.pixclock = 171521, .bpp = 16,
.xres = 320, .yres = 240,
.hsync_len = 5, .vsync_len = 1,
.left_margin = 61, .upper_margin = 3,
.right_margin = 9, .lower_margin = 0,
.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
.lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
.lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
.backlight_power = assabet_lcd_backlight_power,
.lcd_power = assabet_lcd_power,
.set_visual = assabet_lcd_set_visual,
};
#else
static void assabet_pal_backlight_power(int on)
{
ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
}
static void assabet_pal_power(int on)
{
ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
}
static struct sa1100fb_mach_info pal_info = {
.pixclock = 67797, .bpp = 16,
.xres = 640, .yres = 512,
.hsync_len = 64, .vsync_len = 6,
.left_margin = 125, .upper_margin = 70,
.right_margin = 115, .lower_margin = 36,
.lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
.lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
.backlight_power = assabet_pal_backlight_power,
.lcd_power = assabet_pal_power,
.set_visual = assabet_lcd_set_visual,
};
#endif
#ifdef CONFIG_ASSABET_NEPONSET
static struct resource neponset_resources[] = {
DEFINE_RES_MEM(0x10000000, 0x08000000),
DEFINE_RES_MEM(0x18000000, 0x04000000),
DEFINE_RES_MEM(0x40000000, SZ_8K),
DEFINE_RES_IRQ(IRQ_GPIO25),
};
#endif
static void __init assabet_init(void)
{
/*
* Ensure that the power supply is in "high power" mode.
*/
GPSR = GPIO_GPIO16;
GPDR |= GPIO_GPIO16;
/*
* Ensure that these pins are set as outputs and are driving
* logic 0. This ensures that we won't inadvertently toggle
* the WS latch in the CPLD, and we don't float causing
* excessive power drain. --rmk
*/
GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
/*
* Also set GPIO27 as an output; this is used to clock UART3
* via the FPGA and as otherwise has no pullups or pulldowns,
* so stop it floating.
*/
GPCR = GPIO_GPIO27;
GPDR |= GPIO_GPIO27;
/*
* Set up registers for sleep mode.
*/
PWER = PWER_GPIO0;
PGSR = 0;
PCFR = 0;
PSDR = 0;
PPDR |= PPC_TXD3 | PPC_TXD1;
PPSR |= PPC_TXD3 | PPC_TXD1;
sa11x0_ppc_configure_mcp();
if (machine_has_neponset()) {
/*
* Angel sets this, but other bootloaders may not.
*
* This must precede any driver calls to BCR_set()
* or BCR_clear().
*/
ASSABET_BCR = BCR_value = ASSABET_BCR_DB1111;
#ifndef CONFIG_ASSABET_NEPONSET
printk( "Warning: Neponset detected but full support "
"hasn't been configured in the kernel\n" );
#else
platform_device_register_simple("neponset", 0,
neponset_resources, ARRAY_SIZE(neponset_resources));
#endif
}
#ifndef ASSABET_PAL_VIDEO
sa11x0_register_lcd(&lq039q2ds54_info);
#else
sa11x0_register_lcd(&pal_video);
#endif
sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources,
ARRAY_SIZE(assabet_flash_resources));
sa11x0_register_irda(&assabet_irda_data);
sa11x0_register_mcp(&assabet_mcp_data);
}
/*
* On Assabet, we must probe for the Neponset board _before_
* paging_init() has occurred to actually determine the amount
* of RAM available. To do so, we map the appropriate IO section
* in the page table here in order to access GPIO registers.
*/
static void __init map_sa1100_gpio_regs( void )
{
unsigned long phys = __PREG(GPLR) & PMD_MASK;
unsigned long virt = (unsigned long)io_p2v(phys);
int prot = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_DOMAIN(DOMAIN_IO);
pmd_t *pmd;
pmd = pmd_offset(pud_offset(pgd_offset_k(virt), virt), virt);
*pmd = __pmd(phys | prot);
flush_pmd_entry(pmd);
}
/*
* Read System Configuration "Register"
* (taken from "Intel StrongARM SA-1110 Microprocessor Development Board
* User's Guide", section 4.4.1)
*
* This same scan is performed in arch/arm/boot/compressed/head-sa1100.S
* to set up the serial port for decompression status messages. We
* repeat it here because the kernel may not be loaded as a zImage, and
* also because it's a hassle to communicate the SCR value to the kernel
* from the decompressor.
*
* Note that IRQs are guaranteed to be disabled.
*/
static void __init get_assabet_scr(void)
{
unsigned long uninitialized_var(scr), i;
GPDR |= 0x3fc; /* Configure GPIO 9:2 as outputs */
GPSR = 0x3fc; /* Write 0xFF to GPIO 9:2 */
GPDR &= ~(0x3fc); /* Configure GPIO 9:2 as inputs */
for(i = 100; i--; ) /* Read GPIO 9:2 */
scr = GPLR;
GPDR |= 0x3fc; /* restore correct pin direction */
scr &= 0x3fc; /* save as system configuration byte. */
SCR_value = scr;
}
static void __init
fixup_assabet(struct tag *tags, char **cmdline, struct meminfo *mi)
{
/* This must be done before any call to machine_has_neponset() */
map_sa1100_gpio_regs();
get_assabet_scr();
if (machine_has_neponset())
printk("Neponset expansion board detected\n");
}
static void assabet_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
{
if (port->mapbase == _Ser1UTCR0) {
if (state)
ASSABET_BCR_clear(ASSABET_BCR_RS232EN |
ASSABET_BCR_COM_RTS |
ASSABET_BCR_COM_DTR);
else
ASSABET_BCR_set(ASSABET_BCR_RS232EN |
ASSABET_BCR_COM_RTS |
ASSABET_BCR_COM_DTR);
}
}
/*
* Assabet uses COM_RTS and COM_DTR for both UART1 (com port)
* and UART3 (radio module). We only handle them for UART1 here.
*/
static void assabet_set_mctrl(struct uart_port *port, u_int mctrl)
{
if (port->mapbase == _Ser1UTCR0) {
u_int set = 0, clear = 0;
if (mctrl & TIOCM_RTS)
clear |= ASSABET_BCR_COM_RTS;
else
set |= ASSABET_BCR_COM_RTS;
if (mctrl & TIOCM_DTR)
clear |= ASSABET_BCR_COM_DTR;
else
set |= ASSABET_BCR_COM_DTR;
ASSABET_BCR_clear(clear);
ASSABET_BCR_set(set);
}
}
static u_int assabet_get_mctrl(struct uart_port *port)
{
u_int ret = 0;
u_int bsr = ASSABET_BSR;
/* need 2 reads to read current value */
bsr = ASSABET_BSR;
if (port->mapbase == _Ser1UTCR0) {
if (bsr & ASSABET_BSR_COM_DCD)
ret |= TIOCM_CD;
if (bsr & ASSABET_BSR_COM_CTS)
ret |= TIOCM_CTS;
if (bsr & ASSABET_BSR_COM_DSR)
ret |= TIOCM_DSR;
} else if (port->mapbase == _Ser3UTCR0) {
if (bsr & ASSABET_BSR_RAD_DCD)
ret |= TIOCM_CD;
if (bsr & ASSABET_BSR_RAD_CTS)
ret |= TIOCM_CTS;
if (bsr & ASSABET_BSR_RAD_DSR)
ret |= TIOCM_DSR;
if (bsr & ASSABET_BSR_RAD_RI)
ret |= TIOCM_RI;
} else {
ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR;
}
return ret;
}
static struct sa1100_port_fns assabet_port_fns __initdata = {
.set_mctrl = assabet_set_mctrl,
.get_mctrl = assabet_get_mctrl,
.pm = assabet_uart_pm,
};
static struct map_desc assabet_io_desc[] __initdata = {
{ /* Board Control Register */
.virtual = 0xf1000000,
.pfn = __phys_to_pfn(0x12000000),
.length = 0x00100000,
.type = MT_DEVICE
}, { /* MQ200 */
.virtual = 0xf2800000,
.pfn = __phys_to_pfn(0x4b800000),
.length = 0x00800000,
.type = MT_DEVICE
}
};
static void __init assabet_map_io(void)
{
sa1100_map_io();
iotable_init(assabet_io_desc, ARRAY_SIZE(assabet_io_desc));
/*
* Set SUS bit in SDCR0 so serial port 1 functions.
* Its called GPCLKR0 in my SA1110 manual.
*/
Ser1SDCR0 |= SDCR0_SUS;
if (!machine_has_neponset())
sa1100_register_uart_fns(&assabet_port_fns);
/*
* When Neponset is attached, the first UART should be
* UART3. That's what Angel is doing and many documents
* are stating this.
*
* We do the Neponset mapping even if Neponset support
* isn't compiled in so the user will still get something on
* the expected physical serial port.
*
* We no longer do this; not all boot loaders support it,
* and UART3 appears to be somewhat unreliable with blob.
*/
sa1100_register_uart(0, 1);
sa1100_register_uart(2, 3);
}
/* LEDs */
#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
struct assabet_led {
struct led_classdev cdev;
u32 mask;
};
/*
* The triggers lines up below will only be used if the
* LED triggers are compiled in.
*/
static const struct {
const char *name;
const char *trigger;
} assabet_leds[] = {
{ "assabet:red", "cpu0",},
{ "assabet:green", "heartbeat", },
};
/*
* The LED control in Assabet is reversed:
* - setting bit means turn off LED
* - clearing bit means turn on LED
*/
static void assabet_led_set(struct led_classdev *cdev,
enum led_brightness b)
{
struct assabet_led *led = container_of(cdev,
struct assabet_led, cdev);
if (b != LED_OFF)
ASSABET_BCR_clear(led->mask);
else
ASSABET_BCR_set(led->mask);
}
static enum led_brightness assabet_led_get(struct led_classdev *cdev)
{
struct assabet_led *led = container_of(cdev,
struct assabet_led, cdev);
return (ASSABET_BCR & led->mask) ? LED_OFF : LED_FULL;
}
static int __init assabet_leds_init(void)
{
int i;
if (!machine_is_assabet())
return -ENODEV;
for (i = 0; i < ARRAY_SIZE(assabet_leds); i++) {
struct assabet_led *led;
led = kzalloc(sizeof(*led), GFP_KERNEL);
if (!led)
break;
led->cdev.name = assabet_leds[i].name;
led->cdev.brightness_set = assabet_led_set;
led->cdev.brightness_get = assabet_led_get;
led->cdev.default_trigger = assabet_leds[i].trigger;
if (!i)
led->mask = ASSABET_BCR_LED_RED;
else
led->mask = ASSABET_BCR_LED_GREEN;
if (led_classdev_register(NULL, &led->cdev) < 0) {
kfree(led);
break;
}
}
return 0;
}
/*
* Since we may have triggers on any subsystem, defer registration
* until after subsystem_init.
*/
fs_initcall(assabet_leds_init);
#endif
MACHINE_START(ASSABET, "Intel-Assabet")
.atag_offset = 0x100,
.fixup = fixup_assabet,
.map_io = assabet_map_io,
.nr_irqs = SA1100_NR_IRQS,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
.init_machine = assabet_init,
.init_late = sa11x0_init_late,
#ifdef CONFIG_SA1111
.dma_zone_size = SZ_1M,
#endif
.restart = sa11x0_restart,
MACHINE_END