linux/Documentation/driver-api/ipmb.rst
Vijay Khemka 042f057fe2 drivers: ipmi: Support raw i2c packet in IPMB
Many IPMB devices don't support smbus protocol and this driver
only supports the smbus protocol at the moment.

Added support for the i2c protocol as well. There will be a variable
"i2c-protocol" passed by the device tree or ACPI table which determines
whether the protocol is i2c or smbus.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Asmaa Mnebhi <asmaa@mellanox.com>
Message-Id: <20191211185604.1266063-1-vijaykhemka@fb.com>
[IPMB.txt had moved to driver-api/ipmb.rst, I adjusted]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2019-12-11 13:21:36 -06:00

110 lines
3.5 KiB
ReStructuredText

==============================
IPMB Driver for a Satellite MC
==============================
The Intelligent Platform Management Bus or IPMB, is an
I2C bus that provides a standardized interconnection between
different boards within a chassis. This interconnection is
between the baseboard management (BMC) and chassis electronics.
IPMB is also associated with the messaging protocol through the
IPMB bus.
The devices using the IPMB are usually management
controllers that perform management functions such as servicing
the front panel interface, monitoring the baseboard,
hot-swapping disk drivers in the system chassis, etc...
When an IPMB is implemented in the system, the BMC serves as
a controller to give system software access to the IPMB. The BMC
sends IPMI requests to a device (usually a Satellite Management
Controller or Satellite MC) via IPMB and the device
sends a response back to the BMC.
For more information on IPMB and the format of an IPMB message,
refer to the IPMB and IPMI specifications.
IPMB driver for Satellite MC
----------------------------
ipmb-dev-int - This is the driver needed on a Satellite MC to
receive IPMB messages from a BMC and send a response back.
This driver works with the I2C driver and a userspace
program such as OpenIPMI:
1) It is an I2C slave backend driver. So, it defines a callback
function to set the Satellite MC as an I2C slave.
This callback function handles the received IPMI requests.
2) It defines the read and write functions to enable a user
space program (such as OpenIPMI) to communicate with the kernel.
Load the IPMB driver
--------------------
The driver needs to be loaded at boot time or manually first.
First, make sure you have the following in your config file:
CONFIG_IPMB_DEVICE_INTERFACE=y
1) If you want the driver to be loaded at boot time:
a) Add this entry to your ACPI table, under the appropriate SMBus::
Device (SMB0) // Example SMBus host controller
{
Name (_HID, "<Vendor-Specific HID>") // Vendor-Specific HID
Name (_UID, 0) // Unique ID of particular host controller
:
:
Device (IPMB)
{
Name (_HID, "IPMB0001") // IPMB device interface
Name (_UID, 0) // Unique device identifier
}
}
b) Example for device tree::
&i2c2 {
status = "okay";
ipmb@10 {
compatible = "ipmb-dev";
reg = <0x10>;
i2c-protocol;
};
};
If xmit of data to be done using raw i2c block vs smbus
then "i2c-protocol" needs to be defined as above.
2) Manually from Linux::
modprobe ipmb-dev-int
Instantiate the device
----------------------
After loading the driver, you can instantiate the device as
described in 'Documentation/i2c/instantiating-devices.rst'.
If you have multiple BMCs, each connected to your Satellite MC via
a different I2C bus, you can instantiate a device for each of
those BMCs.
The name of the instantiated device contains the I2C bus number
associated with it as follows::
BMC1 ------ IPMB/I2C bus 1 ---------| /dev/ipmb-1
Satellite MC
BMC1 ------ IPMB/I2C bus 2 ---------| /dev/ipmb-2
For instance, you can instantiate the ipmb-dev-int device from
user space at the 7 bit address 0x10 on bus 2::
# echo ipmb-dev 0x1010 > /sys/bus/i2c/devices/i2c-2/new_device
This will create the device file /dev/ipmb-2, which can be accessed
by the user space program. The device needs to be instantiated
before running the user space program.