linux/Documentation/devicetree/bindings/spi/spi-rspi.txt
Fabrizio Castro 10c1705ece spi: rspi: Add r8a7743/5 to the compatible list
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-19 14:14:07 +01:00

73 lines
2.7 KiB
Plaintext

Device tree configuration for Renesas RSPI/QSPI driver
Required properties:
- compatible : For Renesas Serial Peripheral Interface on legacy SH:
"renesas,rspi-<soctype>", "renesas,rspi" as fallback.
For Renesas Serial Peripheral Interface on RZ/A1H:
"renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback.
For Quad Serial Peripheral Interface on R-Car Gen2 and
RZ/G1 devices:
"renesas,qspi-<soctype>", "renesas,qspi" as fallback.
Examples with soctypes are:
- "renesas,rspi-sh7757" (SH)
- "renesas,rspi-r7s72100" (RZ/A1H)
- "renesas,qspi-r8a7743" (RZ/G1M)
- "renesas,qspi-r8a7745" (RZ/G1E)
- "renesas,qspi-r8a7790" (R-Car H2)
- "renesas,qspi-r8a7791" (R-Car M2-W)
- "renesas,qspi-r8a7792" (R-Car V2H)
- "renesas,qspi-r8a7793" (R-Car M2-N)
- "renesas,qspi-r8a7794" (R-Car E2)
- reg : Address start and address range size of the device
- interrupts : A list of interrupt-specifiers, one for each entry in
interrupt-names.
If interrupt-names is not present, an interrupt specifier
for a single muxed interrupt.
- interrupt-names : A list of interrupt names. Should contain (if present):
- "error" for SPEI,
- "rx" for SPRI,
- "tx" to SPTI,
- "mux" for a single muxed interrupt.
- interrupt-parent : The phandle for the interrupt controller that
services interrupts for this device.
- num-cs : Number of chip selects. Some RSPI cores have more than 1.
- #address-cells : Must be <1>
- #size-cells : Must be <0>
Optional properties:
- clocks : Must contain a reference to the functional clock.
- dmas : Must contain a list of two references to DMA specifiers,
one for transmission, and one for reception.
- dma-names : Must contain a list of two DMA names, "tx" and "rx".
Pinctrl properties might be needed, too. See
Documentation/devicetree/bindings/pinctrl/renesas,*.
Examples:
spi0: spi@e800c800 {
compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
reg = <0xe800c800 0x24>;
interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>,
<0 239 IRQ_TYPE_LEVEL_HIGH>,
<0 240 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error", "rx", "tx";
interrupt-parent = <&gic>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
};
spi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7791", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
interrupt-parent = <&gic>;
interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>;
dma-names = "tx", "rx";
};