linux/Documentation/netlabel/cipso_ipv4.txt
Henrik Austad a7ddcea58a Drop all 00-INDEX files from Documentation/
This is a respin with a wider audience (all that get_maintainer returned)
and I know this spams a *lot* of people. Not sure what would be the correct
way, so my apologies for ruining your inbox.

The 00-INDEX files are supposed to give a summary of all files present
in a directory, but these files are horribly out of date and their
usefulness is brought into question. Often a simple "ls" would reveal
the same information as the filenames are generally quite descriptive as
a short introduction to what the file covers (it should not surprise
anyone what Documentation/sched/sched-design-CFS.txt covers)

A few years back it was mentioned that these files were no longer really
needed, and they have since then grown further out of date, so perhaps
it is time to just throw them out.

A short status yields the following _outdated_ 00-INDEX files, first
counter is files listed in 00-INDEX but missing in the directory, last
is files present but not listed in 00-INDEX.

List of outdated 00-INDEX:
Documentation: (4/10)
Documentation/sysctl: (0/1)
Documentation/timers: (1/0)
Documentation/blockdev: (3/1)
Documentation/w1/slaves: (0/1)
Documentation/locking: (0/1)
Documentation/devicetree: (0/5)
Documentation/power: (1/1)
Documentation/powerpc: (0/5)
Documentation/arm: (1/0)
Documentation/x86: (0/9)
Documentation/x86/x86_64: (1/1)
Documentation/scsi: (4/4)
Documentation/filesystems: (2/9)
Documentation/filesystems/nfs: (0/2)
Documentation/cgroup-v1: (0/2)
Documentation/kbuild: (0/4)
Documentation/spi: (1/0)
Documentation/virtual/kvm: (1/0)
Documentation/scheduler: (0/2)
Documentation/fb: (0/1)
Documentation/block: (0/1)
Documentation/networking: (6/37)
Documentation/vm: (1/3)

Then there are 364 subdirectories in Documentation/ with several files that
are missing 00-INDEX alltogether (and another 120 with a single file and no
00-INDEX).

I don't really have an opinion to whether or not we /should/ have 00-INDEX,
but the above 00-INDEX should either be removed or be kept up to date. If
we should keep the files, I can try to keep them updated, but I rather not
if we just want to delete them anyway.

As a starting point, remove all index-files and references to 00-INDEX and
see where the discussion is going.

Signed-off-by: Henrik Austad <henrik@austad.us>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Just-do-it-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: [Almost everybody else]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2018-09-09 15:08:58 -06:00

50 lines
2.2 KiB
Plaintext

NetLabel CIPSO/IPv4 Protocol Engine
==============================================================================
Paul Moore, paul.moore@hp.com
May 17, 2006
* Overview
The NetLabel CIPSO/IPv4 protocol engine is based on the IETF Commercial
IP Security Option (CIPSO) draft from July 16, 1992. A copy of this
draft can be found in this directory
(draft-ietf-cipso-ipsecurity-01.txt). While the IETF draft never made
it to an RFC standard it has become a de-facto standard for labeled
networking and is used in many trusted operating systems.
* Outbound Packet Processing
The CIPSO/IPv4 protocol engine applies the CIPSO IP option to packets by
adding the CIPSO label to the socket. This causes all packets leaving the
system through the socket to have the CIPSO IP option applied. The socket's
CIPSO label can be changed at any point in time, however, it is recommended
that it is set upon the socket's creation. The LSM can set the socket's CIPSO
label by using the NetLabel security module API; if the NetLabel "domain" is
configured to use CIPSO for packet labeling then a CIPSO IP option will be
generated and attached to the socket.
* Inbound Packet Processing
The CIPSO/IPv4 protocol engine validates every CIPSO IP option it finds at the
IP layer without any special handling required by the LSM. However, in order
to decode and translate the CIPSO label on the packet the LSM must use the
NetLabel security module API to extract the security attributes of the packet.
This is typically done at the socket layer using the 'socket_sock_rcv_skb()'
LSM hook.
* Label Translation
The CIPSO/IPv4 protocol engine contains a mechanism to translate CIPSO security
attributes such as sensitivity level and category to values which are
appropriate for the host. These mappings are defined as part of a CIPSO
Domain Of Interpretation (DOI) definition and are configured through the
NetLabel user space communication layer. Each DOI definition can have a
different security attribute mapping table.
* Label Translation Cache
The NetLabel system provides a framework for caching security attribute
mappings from the network labels to the corresponding LSM identifiers. The
CIPSO/IPv4 protocol engine supports this caching mechanism.