linux/drivers/irqchip/irq-gic-common.c
Marc Zyngier 0e5cb77706 irqchip/gic: Split vGIC probing information from the GIC code
The vGIC advertising code is unsurprisingly very much tied to
the GIC implementations. However, we are about to extend the
support to lesser implementations.

Let's dissociate the vgic registration from the GIC code and
move it into KVM, where it makes a bit more sense. This also
allows us to mark the gic_kvm_info structures as __initdata.

Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
2021-06-01 10:45:58 +01:00

145 lines
3.6 KiB
C

// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2002 ARM Limited, All Rights Reserved.
*/
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqchip/arm-gic.h>
#include "irq-gic-common.h"
static DEFINE_RAW_SPINLOCK(irq_controller_lock);
void gic_enable_of_quirks(const struct device_node *np,
const struct gic_quirk *quirks, void *data)
{
for (; quirks->desc; quirks++) {
if (!of_device_is_compatible(np, quirks->compatible))
continue;
if (quirks->init(data))
pr_info("GIC: enabling workaround for %s\n",
quirks->desc);
}
}
void gic_enable_quirks(u32 iidr, const struct gic_quirk *quirks,
void *data)
{
for (; quirks->desc; quirks++) {
if (quirks->compatible)
continue;
if (quirks->iidr != (quirks->mask & iidr))
continue;
if (quirks->init(data))
pr_info("GIC: enabling workaround for %s\n",
quirks->desc);
}
}
int gic_configure_irq(unsigned int irq, unsigned int type,
void __iomem *base, void (*sync_access)(void))
{
u32 confmask = 0x2 << ((irq % 16) * 2);
u32 confoff = (irq / 16) * 4;
u32 val, oldval;
int ret = 0;
unsigned long flags;
/*
* Read current configuration register, and insert the config
* for "irq", depending on "type".
*/
raw_spin_lock_irqsave(&irq_controller_lock, flags);
val = oldval = readl_relaxed(base + confoff);
if (type & IRQ_TYPE_LEVEL_MASK)
val &= ~confmask;
else if (type & IRQ_TYPE_EDGE_BOTH)
val |= confmask;
/* If the current configuration is the same, then we are done */
if (val == oldval) {
raw_spin_unlock_irqrestore(&irq_controller_lock, flags);
return 0;
}
/*
* Write back the new configuration, and possibly re-enable
* the interrupt. If we fail to write a new configuration for
* an SPI then WARN and return an error. If we fail to write the
* configuration for a PPI this is most likely because the GIC
* does not allow us to set the configuration or we are in a
* non-secure mode, and hence it may not be catastrophic.
*/
writel_relaxed(val, base + confoff);
if (readl_relaxed(base + confoff) != val)
ret = -EINVAL;
raw_spin_unlock_irqrestore(&irq_controller_lock, flags);
if (sync_access)
sync_access();
return ret;
}
void gic_dist_config(void __iomem *base, int gic_irqs,
void (*sync_access)(void))
{
unsigned int i;
/*
* Set all global interrupts to be level triggered, active low.
*/
for (i = 32; i < gic_irqs; i += 16)
writel_relaxed(GICD_INT_ACTLOW_LVLTRIG,
base + GIC_DIST_CONFIG + i / 4);
/*
* Set priority on all global interrupts.
*/
for (i = 32; i < gic_irqs; i += 4)
writel_relaxed(GICD_INT_DEF_PRI_X4, base + GIC_DIST_PRI + i);
/*
* Deactivate and disable all SPIs. Leave the PPI and SGIs
* alone as they are in the redistributor registers on GICv3.
*/
for (i = 32; i < gic_irqs; i += 32) {
writel_relaxed(GICD_INT_EN_CLR_X32,
base + GIC_DIST_ACTIVE_CLEAR + i / 8);
writel_relaxed(GICD_INT_EN_CLR_X32,
base + GIC_DIST_ENABLE_CLEAR + i / 8);
}
if (sync_access)
sync_access();
}
void gic_cpu_config(void __iomem *base, int nr, void (*sync_access)(void))
{
int i;
/*
* Deal with the banked PPI and SGI interrupts - disable all
* private interrupts. Make sure everything is deactivated.
*/
for (i = 0; i < nr; i += 32) {
writel_relaxed(GICD_INT_EN_CLR_X32,
base + GIC_DIST_ACTIVE_CLEAR + i / 8);
writel_relaxed(GICD_INT_EN_CLR_X32,
base + GIC_DIST_ENABLE_CLEAR + i / 8);
}
/*
* Set priority on PPI and SGI interrupts
*/
for (i = 0; i < nr; i += 4)
writel_relaxed(GICD_INT_DEF_PRI_X4,
base + GIC_DIST_PRI + i * 4 / 4);
if (sync_access)
sync_access();
}