linux/arch/m68k/coldfire/m528x.c
Arnd Bergmann 63aadb7766 m68k: coldfire: use clkdev_lookup on most coldfire
Coldfire is now the only target that implements the clk_get()/clk_put()
helpers itself rather than using the common implementation.

Most coldfire variants only have two distinct clocks and use the clk
code purely for lookup. Change those over to use clkdev_lookup instead
but leave the custom clk interface for those two clocks.

Also leave the four SoCs that have gated clocks.

Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-06-08 17:00:09 +02:00

144 lines
3.8 KiB
C

// SPDX-License-Identifier: GPL-2.0
/***************************************************************************/
/*
* m528x.c -- platform support for ColdFire 528x based boards
*
* Sub-architcture dependent initialization code for the Freescale
* 5280, 5281 and 5282 CPUs.
*
* Copyright (C) 1999-2003, Greg Ungerer (gerg@snapgear.com)
* Copyright (C) 2001-2003, SnapGear Inc. (www.snapgear.com)
*/
/***************************************************************************/
#include <linux/clkdev.h>
#include <linux/kernel.h>
#include <linux/param.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
#include <asm/mcfuart.h>
#include <asm/mcfclk.h>
/***************************************************************************/
DEFINE_CLK(pll, "pll.0", MCF_CLK);
DEFINE_CLK(sys, "sys.0", MCF_BUSCLK);
static struct clk_lookup m528x_clk_lookup[] = {
CLKDEV_INIT(NULL, "pll.0", &clk_pll),
CLKDEV_INIT(NULL, "sys.0", &clk_sys),
CLKDEV_INIT("mcfpit.0", NULL, &clk_pll),
CLKDEV_INIT("mcfpit.1", NULL, &clk_pll),
CLKDEV_INIT("mcfpit.2", NULL, &clk_pll),
CLKDEV_INIT("mcfpit.3", NULL, &clk_pll),
CLKDEV_INIT("mcfuart.0", NULL, &clk_sys),
CLKDEV_INIT("mcfuart.1", NULL, &clk_sys),
CLKDEV_INIT("mcfuart.2", NULL, &clk_sys),
CLKDEV_INIT("mcfqspi.0", NULL, &clk_sys),
CLKDEV_INIT("fec.0", NULL, &clk_sys),
CLKDEV_INIT("imx1-i2c.0", NULL, &clk_sys),
};
/***************************************************************************/
static void __init m528x_qspi_init(void)
{
#if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
/* setup Port QS for QSPI with gpio CS control */
__raw_writeb(0x07, MCFGPIO_PQSPAR);
#endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */
}
/***************************************************************************/
static void __init m528x_i2c_init(void)
{
#if IS_ENABLED(CONFIG_I2C_IMX)
u16 paspar;
/* setup Port AS Pin Assignment Register for I2C */
/* set PASPA0 to SCL and PASPA1 to SDA */
paspar = readw(MCFGPIO_PASPAR);
paspar |= 0xF;
writew(paspar, MCFGPIO_PASPAR);
#endif /* IS_ENABLED(CONFIG_I2C_IMX) */
}
/***************************************************************************/
static void __init m528x_uarts_init(void)
{
u8 port;
/* make sure PUAPAR is set for UART0 and UART1 */
port = readb(MCFGPIO_PUAPAR);
port |= 0x03 | (0x03 << 2);
writeb(port, MCFGPIO_PUAPAR);
}
/***************************************************************************/
static void __init m528x_fec_init(void)
{
u16 v16;
/* Set multi-function pins to ethernet mode for fec0 */
v16 = readw(MCFGPIO_PASPAR);
writew(v16 | 0xf00, MCFGPIO_PASPAR);
writeb(0xc0, MCFGPIO_PEHLPAR);
}
/***************************************************************************/
#ifdef CONFIG_WILDFIRE
void wildfire_halt(void)
{
writeb(0, 0x30000007);
writeb(0x2, 0x30000007);
}
#endif
#ifdef CONFIG_WILDFIREMOD
void wildfiremod_halt(void)
{
printk(KERN_INFO "WildFireMod hibernating...\n");
/* Set portE.5 to Digital IO */
writew(readw(MCFGPIO_PEPAR) & ~(1 << (5 * 2)), MCFGPIO_PEPAR);
/* Make portE.5 an output */
writeb(readb(MCFGPIO_PDDR_E) | (1 << 5), MCFGPIO_PDDR_E);
/* Now toggle portE.5 from low to high */
writeb(readb(MCFGPIO_PODR_E) & ~(1 << 5), MCFGPIO_PODR_E);
writeb(readb(MCFGPIO_PODR_E) | (1 << 5), MCFGPIO_PODR_E);
printk(KERN_EMERG "Failed to hibernate. Halting!\n");
}
#endif
void __init config_BSP(char *commandp, int size)
{
#ifdef CONFIG_WILDFIRE
mach_halt = wildfire_halt;
#endif
#ifdef CONFIG_WILDFIREMOD
mach_halt = wildfiremod_halt;
#endif
mach_sched_init = hw_timer_init;
m528x_uarts_init();
m528x_fec_init();
m528x_qspi_init();
m528x_i2c_init();
clkdev_add_table(m528x_clk_lookup, ARRAY_SIZE(m528x_clk_lookup));
}
/***************************************************************************/